NI-MAX/NVIORef.dll and RTE 8.2.x nightmare. pls someone sends me a RTE 8.2.1 dll?

hi there
i just installed LV 7.1 PDS 2005Q3 (default installation), and after that LV 8.5 PDS 2007Q4 (default installation). all works fine except the NI-MAX panels (e.g. devices test panels etc.). see attached ni-max (sorry for the german version..). this is annoying because i cannot add any devices etc.!
LVBroker needs the RTE 8.2.1 , well OK, i downloaded the RTE 8.2.1 and ran the installer. the installer says "8.2.1 already installed", and so does MAX (see rte attachment). so the installer does nothing at all. the only content of the \Shared\LabVIEW Run-Time\8.2 - directory is the NVIORef.dll with version 8.2.0.131. i assume this is the 8.20 dll version, and not the 8.2.1.
i'd like to replace this single dll with a "real" 8.2.1 dll. can someone please send me this dll?. or does someone have a better idea?
the NVIORef.dll can be found in the directory \Shared\LabVIEW Run-Time\8.2, you can find out the version number in explorer with right click on the dll and then click the "version" tab page.
thanks in advance
Best regards
chris
CL(A)Dly bending G-Force with LabVIEW
famous last words: "oh my god, it is full of stars!"
Attachments:
ni-max.JPG ‏18 KB
rte.JPG ‏72 KB

Chris,
I just checked my LabVIEW 8.2.1 installation, and the version of the NVIORef.dll in the Runtime directory is still 8.2.0.131.
BUT: this is not the only content of the Runtime directory, as you can see in the screenshot attached to this post.
What OS are you using? If it is Microsoft Windows 2000, be sure to have at least SP3 installed before running the LabVIEW-RTE Setup.
Regarding the broken Test Panels in MAX - do you have any drivers installed (VISA, DAQmx, ...)? If so, did you reinstall them after running the LabVIEW 8.5 setup?
From my personal experience, I dare recommend you a clean new installation of both LabVIEW versions and the 8.2.1 runtime engine, best performed in the version order (7.1, then the 8.2.1 RTE, than 8.5.
There is a forum entry with a download link to MSI blast and a very good PDF which points you to the Windows Registry keys that you need to delete after deinstallation, which you can find here:
http://forums.ni.com/ni/board/message?board.id=250&message.id=34373&requireLogin=False
I think it's worth giving a try.
Attachments:
version check1.gif ‏59 KB

Similar Messages

Need lvrt.dll and lvapp.rsc Ver. 7.1.1

hi there
can someone please send me the lvrt.dll and the lvapp.rsc Version 7.1.1?
Both can be found at ..\National Instruments\Shared\LabVIEW Run-Time\7.1
because the files are quite large you can post them at ftp://ftp.ni.com/incoming/, i'll fetch them from there.
Best regards
chris
CL(A)Dly bending G-Force with LabVIEW
famous last words: "oh my god, it is full of stars!"

hi carsten
thanks for your answer, but to avoid troubles with several versions installed on my machine i don't want to install the rte 7.1.1. i played around with some files and then i managed it to overwrite the two files with 7.1 versions.....
Best regards
chris
CL(A)Dly bending G-Force with LabVIEW
famous last words: "oh my god, it is full of stars!"

Creating DLL and identifying LVRTE for 32bit/64bit/WinXP/Win7

I have a labVIEW 2010 application (created on 32bitXP) to be distributed
for
-Windows XP 32 bit
-Windows XP 64 bit
-Windows 7 32 bit
-Windows 7 64 bit.
What kind of runtime engine will I need?
I also found that
- there is no runtime engine available for WinXP64 bit, what do I do for
this
OS?
- there are multiple runtime engines for LV2010 (min/std/64bit).
Can someone pls help me to dentify,
Which link to use for which OS/bit combination with LV 2010.
Also can someone help me to identify, if I need to build the application
(EXE
or DLL) in 4 different ways, for these 4 OS?
regards
Sandeep
NI Software : LabVIEW version 2010
NI Hardware : None device

Hi Greg,
Thank you for your response too.
Yes, I must have 32 bit RTE for running 32 bit DLL.
And also I do want to have 32 bit DLL only (& not 64 bit one).
To explain, let me propose the following case.
I have a C# created (built in 32 bit mode for x86) parent EXE .
I have C# created (built in 32 bit mode for x86) child DLL.
The child DLL gets called successfully by parent EXE. In all 4 possible OS combinations. ie. 32bitWinXP,64bitWinXP,32bitWin64,64bitWin64.
But..
When I create a 32 bit DLL from 32 bit LabVIEW on XP32bit,
it never gives me success to be called by 32 bit C# parent in 64bitWinXP, 32bitWin7, 64bitWin7.
I am aware that I must not create 64bit DLL, becasue my C# EXE is built in 32 bit (& That's how it must be to be able to run in all 4 OS combinations).
Below is my thread
http://forums.ni.com/t5/LabVIEW/Creating-DLL-and-identifying-LVRTE-for-32bit-64bit-WinXP-Win7/m-p/13...
Thanks for reading thru.

TS1368 I'm a PC user with an itunes account for several years. I updated my itunes and now it wont open and shows me 'missing file MSVCR80.dll,and error 7(Window error 126)' keep coming up even after re-installing itunes . What should i do?

I'm a PC user with an itunes account for several years. I updated my itunes and now it wont open and shows me 'missing file MSVCR80.dll,and error 7(Window error 126)' keep coming up even after re-installing itunes . What should i do?

Click here and follow the instructions.
(98897)

What is new with MAX 2.0 and is it compatible with Session Manager?

We added non-IVI instrument information in, basically the same structure as for IVI instruments,
into the ivi.ini file to keep all instrument information in the same place. Using MAX Version 1.1 caused no problems whatsoever and the system worked fine. With the advent of MAX 2.0 you seem to use ivi.ini as well as config.mxs to store instrument information. What we have found now is that given a working ivi.ini file from MAX 1.1, we end up with 2 or 3 copies of all the devices in the IVI Instruments->Devices section! When the duplicate entries are deleted and the application exited, the
ivi.ini file is updated minus the [Hardware->] sections which contain the resource descriptors that our appl
ications look for. As an added complication, under MAX 2.1 (From an evaluation of the Switch Executive) It behaves the same, except that it almost always crashes with one of the following errors. 'OLEChannelWnd Fatal Error', or 'Error#26 window.cpp line 10028 Labview Version 6.0.2' Once opened and closed MAX 2.1 will not open again! (Note we do not have LabVIEW on the system.) What is the relationship between the config.mxs and ivi.ini now? Also, your Session Manager application (for use with TestStand) extracts information from ivi.ini and may expect entries to be manually entered into ivi.ini (e.g. NISessionManager_Reset = True) i.e. Is the TestStand Session Manager compatible with MAX 2.0?

Brian,
The primary difference between MAX 1.1 and 2.x is that there is a new internal architecture. MAX 2.x synchronizes data between the config.mxs and the ivi.ini. The reason you're having trouble is that user-editing of the ivi.ini file is not supported with MAX 2.x.
Some better solutions to accomplish what you want:
1. Do as Mark Ireton suggested in his answer
2. Use the IVI Run-Time Configuration functions. They will allow you to dynamically configure your Logical Names, Virtual Instruments, Instrument Drivers, and Devices. You can then use your own format for storing and retrieving that information, and use the relevant pieces for each execution. You can find information on these functions in the IVI CVI Help file located in Start >> National I
nstruments >> IVI Driver Toolset folder. Go to the chapter on Run-time Initialization Configuration.
I strongly suggest #2, because those functions will continue to be supported in the future, while other mechanisms may not be.
--Bankim
Bankim Tejani
National Instruments

Issues with Shell32.dll, NTDLL.DLL and Migration from Windows 2003 to Windows 2012

Hello all,
I am new to ThinApp and working as a consultant to help a company migrate older Windows 2003 software to Windows 2012. They have purchased ThinApp 5.0.4.5 so that is what we will be using.
We have created a clean 2003 VM and did a pre-scan
We loaded the application and configured it and then did a capture.
We then tested the capture the 2003 VM and it works
We then loaded the capture on a Clean 2003 VM and it works
We then loaded onto a 2012 VM and when running the app from a command window get an error -missing import shell32.dll:StrCpyNW
If we run the capture in Emulation Mode on 2012 VM, we do not get the Shell32.dll error but instead the cmd fails with a Fault Module Name - NTDLL.DLL error
I am sure I am just missing the correct location to identify or configure the capture - but do not have the experience to know where yet. (Taking training next week).
Until then, is there any suggestions which I can try?
Thanks for your time in advance,
Vince

Tried and done that. The main issue while configuring the printer from the printer Web Interface is that there is no access to the Digital Sending section due to a problem with the "Sun Java plug in" I think the code mentions 1.31. or similar.
We downloaded the java plug in and installed it. No progress.
We reset the printer to defaults and reconfigured it .. It sees the smtp gateway and access it but fails sending email with scanned documents..
We have tried in very different ways. We connected the printer to another domain SBS server 2003 and it works beautifully. So, I have no idea on what is the problem. We created a firewall exception for ports 390. 1783 from the SBS to the Printer
and still no go..
We have tried four different accounts and nothing. Same results as stated originally.
Any other suggestions??
JFM

Captivate 6 Errors: Missing file libwinpthread-1.dll and The Application was unable to start correctly (0xc000007b) on Windows 2008 R2

Hi,
I have a problem with Captivate 6 installation on Windows Server 2008 R2. I have 2 different scenarios where I tested but the result is same.
1- I used AMEE (Application Manager Enterprise 3.1) to create the installation Package to deploy through SCCM 2012.
Notice that the current package works fine on Windows7 (x86 & x64) but not on 2008 R2 due to an error after I try to launch Captivate.exe application.
The error states that there's a Missing file: libwinpthread-1.dll and if I copy and made a registration of this .DLL file then it sends another error saying: The Application was unable to start correctly (0xc000007b) so it never let me launch the application.
2- Now if I install the package directly from the Original sources(CD) without creating any AMEE package after completing the installation I still have the same error about the DLL missing file.
Is there any fix or workaround to install Captivate 6 on Win2008 R2 ?
Thanks in advance & kind regards.

Wow, No replies so far !!
Any one ??

How do I stop Win7 from breaking my software? Ole32.dll and "Power" service suspected culprits.

Hello and thanks for any help with this.
I built a new computer for my aunt and her one major request is that she still be able to use her card maker software Creatacard (yes misspelled just like that) by American Greetings. I thought this would be no issue, I could give her a much faster machine
and get her off (the no longer supported) WindowsXP all at the same time by moving her to Windows7 and copying all her files over from the old PC to the new one.
I tested the software first on a test PC of mine and found it would not install in a 64bit environment (error message saying use 32bit during install) which I solved by using Windows7 32bit. It worked perfectly so I proceeded to build her machine thinking
that issue resolved. Problem is after the new rig was built and SP1 plus all windows updates were installed the Creatacard software would not load. I get an instant popup message saying "Creatacard Application File has stopped working" with the options
to "Check online for a solution..." and "Close the Program."
Checking online does nothing noticeable and close program doesn't help as every time you reload it fails immediately with the same message. Clicking on the "view problem details" drop menu reveals that this is an APPCRASH with the following clues
Fault Module Name ole32.dll
Fault Module Version 6.1.7601.17514
I have researched and tried everything I could find online about this crash and none of it (up to and including completely re-installing Windows, systematically loading a few Win-updates and trying the app after each batch, editing the registry multiple
times, trying alt versions of ole32.dll, and using a Linux live CD to alter windows settings) has fixed the problem. I have learned the following though:
When windows is first installed the card maker software (CMS from here on) works fine.
After windows updates itself and a few device drivers auto load (like when you first plug in a USB mouse or Flash drive) CMS breaks.
Loading windows normally after it is up to date always causes CMS to crash and give the above message.
When I perform a "clean boot" CMS works fine once again.
When I boot into safe mode CMS works fine.
Someone online suggested a service could be the actual problem and there being 140 of them I used the 50% method to quickly narrow the list and found that yes indeed windows services do appear to be related because if I don't allow the "Power"
service to run the CMS works perfectly. With a bit of testing to see what it does I found that it controlled wake/sleep settings, delay until your monitor goes dark etc and that if the Power service is disabled it remembers the last settings entered and I
thought GREAT! Finally after many days of frustration and being balked by nonsense I have a solution. My aunt will never use/miss the power settings I will set them up for her once and then kill that service and all is well for a Happy Holiday... (from my
research online some may already guess where this is headed) until I went to play a video............ and there was no sound.
A little red X had appeared next to the speaker icon down in the system tray next to the clock and hovering over it gave a popup with "The Audio Service is not running." This is where the BS gets deep. I had of course NOT disabled the sound (Windows
Audio) service and a quick check showed it and all the services it depended on were in fact on and running. The Windows trouble shooter offered to fix the issue and so I let it run but it comes back with "one or more Audio service is not running"
and attempting to restart the service on its own came back with a "Not fixed" result. Now if I go to check dependencies for the "Power" it claims that no other services depend on it and it depends on nothing but that is an outright lie.
Further digging shows me the Power service's "path to executable" as... C:\Windows\system32\svchost.exe -k DcomLauncher and many other services show they depend on DcomLauncher to run.
Long extra trouble shooting session short here is where I am at. I can have the sound working or the CMS but not both.
Uninstalling and re-installing the sound card drivers didn't help (since sound is being stopped at the windows OS level) either.
As soon as I turn on the Power service and reboot the CMS breaks. As soon as I disable the Power service and reboot the CMS works perfectly but all audio breaks. Both of these are a deal breaker as she will not leave her old slow XP machine without her CMS
and I cannot give her a new machine that has no sound. Reboots take 30 seconds on this new PC so were it mine I could just live with it as the CMS has no sound and I don't need music playing when I am designing a Christmas card. Use the sound/power on 99%
of the time and disable them and reboot whenever I make a card and then enable and reboot when I am done. This would be over her head though I fear as she is a senior and not very tech savvy. My question then is...
Is there any way to have the CMS work while still keeping the Windows Audio service (and all the other not listed but still existing dependent services) running? Or alternatively is there something else I can do to the ole32.dll to make it stop the crash/error?
To be clear I would happily accept a system without the Power service running if (like it actually says under dependencies) nothing else other than the "Power Options" in Control Panel ceased to function.

Thanks Michael. Apologies for the slow reply I was away for a bit (holiday blitz at work and visiting family madness etc.etc.) back now, I set both options you requested to "never " and retried the CMS software with no change.
I do have progress of a sort though, as a test I took a separate test PC and put a clean install of Win7 on and loaded up the CMS software (it worked perfectly) and then took the version of ole32.dll off that machine and put it onto the computer I had built
for her (using Linux) and...
got a new error code. Darn I was so sure I had found a clever solution this time lol.
Anyway now when the CMS fails it gives me a similar error but the offending module is "ntdll.dll" sooo... I tried taking the "working" version of ntdll.dll from the test box and moving it over (making sure to back up the existing ones
first so I could put them back if needed) to her new PC and the PC would not boot.
It seems to want the original versions of a few Dynamic Link Libraries and if I could somehow give it those while not breaking Win7 it should theoretically work seeing as it no longer errors with ole32.dll.
ntdll.dll however seems necessary for Win7 to boot.
So what I am wondering now is:
Is there some way to have both versions of the DLL file in the system32 folder (bypassing the "cannot have two files with the exact same name in the same folder" thing) or rename the original DLL's something else and somehow make the CMS look for
the new named versions so the system has the updated DLL's it needs to boot/run and the CMS has the old ones it wants to run or is there someway to have a self contained install of the CMS, say on a USB flash drive and give it it's own E:/windows/system32/needed
dll's path to the files it needs?
Willing to try any other options or settings you may have come up with as well.
Thanks again for your reply and my apologies for not answering sooner.

HT1926 just lost my itunes after doing a update. getting error message MSVCR80.dll and ERROR 7 (Windows error 126)I even tried to reinstall the whole program off from here. What happened? HELP!

I tried to open my Itunes toady on my home computer. It said to update the library so I did. Now it wont open or anything. Tried reinstalling everything and get the error messages posted in the title above. Please Help. I have a lot tied into Itunes. Now when I check for updates it says everything is upt to date but when I try to open it i still get these two erroe messages. MSVCR80.dll and ERROR 7 (Windows error 126)

Hello berlinfire1979,
The following article provides further information regarding this error, and steps that can help get iTunes working again.
iTunes for Windows: "Error 7" message when opening iTunes
http://support.apple.com/kb/TS3074
Cheers,
Allen

How do I use a dll and C++ code to create a labview driver

I have a dll and some .net code to read temperature from a USB HID device I purchased from the website below. In addition some other people have posted their methods/codes of reading the temperatures. I am trying to convert this into a Labview VI but I am very lost.
http://www.no-feature.com/2008/01/taking-advantage-of-your-temper-device.html
It seems I can use the call function to see the functions in the DLL but I cannot use them to actually do anything. I have used serial communcation in labview before but never USB so I feel like I am in a little over my head and would really appreaciate some guidance.

This is not quite easy But to find out how try to reverse engineer this code http://pc8-termo.fis.ucm.es/~josechu/mitemper.zip
Before starting on the job I would recommend doing some testing to see if the code work with your device. I can help if you promise to post the tested code here in this forum. It doable in Labview. It just requires some bit manipulation. Also the unit drive must be installed
To establish a communication link with the device, the settings can be extracted from function SetupCommPort in MITEMPer.c, which are:
9600bps, 8 bits, no parity bit and one stop bit with DTR and RTS enabled.
To initialize the device, the function is init in functions.c. The sequence is:
Calling the Start_IIC function, which in turn calls the SetDataLine and SetClockLine passing 1 as parameters for both, and then calling those two functions again with 0 as parameters.
SetDataLine function sets the RTS line if the passed parameter is 1 or clears the RTS if the passed parameter is 0.
Similarly, the SetClockLine function sets the DTR line if the passed parameter is 1 or clears the DTR line if the passed parameter is 0.
In other words to to initializes the device, we first have to set the RTS, set the DTR, then clear RTS and clear DTR.
So to some part that involves a technique that is often referred to as bit banging. There are 3 groups of 8 bits (one byte) that need to be transferred. Which are, first group 10011110, second group 00000001, third group 01100000.
Then stop the IIC (look in the respective function on what have to be done here).
Start the IIC again.
Transfer another 3 groups of 8 bits.
Stop the IIC.
The sequence of transferring the group can be obtained from the function Transmit in functions.c:
The transmission is done through the DTR and RTS line only. Not through the usual TX data line.
If the data is 1 set the RTS or if the data is 0 clear the RTS.
Then the tick (clock), set the DTR followed by clearing the DTR.
Loop to the next data bit for 8 times.
After 8 bits, set the RTS line and set the DTR line.
Then read the CTS line for acknowledgement (inverted).
Closed by clearing the DTR.
You can follow the C code and find the necessary sequences and data that you need to talk to the device and obtained a reading.
Besides which, my opinion is that Express VIs Carthage must be destroyed deleted
(Sorry no Labview "brag list" so far)

I would like to convert a matlab file into a .dll and use it in LabVIEW. However, when I run the .dll in LabVIEW I get an error stating "... Procedure not found". What could this be? Can anyone help me...

I wish to convert my Matlab files into .dll's so that I can use them in LabVIEW. I am using 'mcc' and 'mbuild' of Matlab to convert my .m files into .c and .dll.
When I try to run the .dll's in LabVIEW, I get an error message in a modal window stating some required .dll or procedure is not found.
How should I resolve this issue. Should I add any other Matlab .dll's in course of making my .dll?
Please help in solving this issue... Thankyou very much.

KJV wrote in message news:<[email protected]>...
> When I run the matlab generated dll, it is stating 'matllb.dll not
> found'. Is it that I should set the path for matlab\bin to include
> all the dll's before I compile? When I make dll from C, it works fine
> in LabVIEW. The problem is from .m to .dll. The problem also arises
> when I convert my .m to .exe. The same error of 'matllb.dll not
> found' comes over. Should I change my matlab compiler options or
> something else? Please help me?
I have the same question,I don't know how to use the matlab DLL file in labview,
I hope someone can descripe the procedure in detail.

When trying to upload a document or attach a document in an email Firefox gives me an error "Failed to load CTDFMRES.dll" and stops responding, I have no issues in any other browsers. And I am using Firefox 4, Fixes???

When trying to upload a document or attach a document in an email Firefox gives me an error "Failed to load CTDFMRES.dll" and stops responding, I have no issues in any other browsers. And I am using Firefox 4, Fixes???

You don't have to disable any addons or extentions!!!You guys are not going to believe this I figured out the problem it's really dumb...ok here goes the attachment uploader loads seperate so I got to thinking it's a popup so I went to options content and under block pop ups there is an option exceptions click on that and in the box type firefox.com and hit allow pow its fixed!!!!! :-)

I'm useing lvwutil32.dll and am getting a "Error 10" (New I/O attempted with old I/O in progress), help :-(

Like my question says, I'm trying to use a buntch of vi's I had gotten about 3 years ago. They work with windows and managing them, along with other standard PC events. I have no problem with the implementation of these vi's into any of my diagrams nor while running the application where my IDE is installed. However, when I try to compile it, I get the "Error 10 occurred at C:\Program File\...\user.lib\lvwutil32.dll". It states 2 possible causes: 1) LabVIEW: Duplicate path & 2) NI-488: New I/O attempted with old I/O in progress".

It has to do with the way you have your build file constructed. The source and destination can't be the same because the application builder attempts to copy the dll into the build directory-which causes the error.
To fix the problem, create a directory containing the dlls you will be using in the build. Specify the dlls in this directory as the source file. Next, after adding all the dlls to the project, click on the "Custom Destinations..." button and for each of the dlls you've added, specify the "Windows System Directory" as the destination WITH NO RELATIVE PATH.
The build should now work...
Mike...
Certified Professional Instructor
Certified LabVIEW Architect
LabVIEW Champion
"... after all, He's not a tame lion..."
Be thinking ahead and mark your dance card for NI Week 2015 now: TS 6139 - Object Oriented First Steps

ITunes install errors: MSVCR80.dll and Error 7 (windows error 126)

All of a sudden my iTunes stopped working, and I get the following error messages:
1. the program can't start because MSVCR80.dll is missing from your computer. Try reinstalling the program to fix this problem
and
2. iTunes was not installed correctly. Please reinstall iTunes. Error 7 (Windows error 126).
Now I've checked the forums and followed the advice of uninstalling all Apple applications, rebooting, and reinstalling iTunes.
This is not working. I've tried installing as Administrator but doesn't make any difference at all.
There must be a way to fix this? I'm not a tech geek but I want to avoid having to take my laptop back to factory settings to sort this out.
Thanks

ITunes tried to automatically update today and failed and then I was also getting the MSVCR80.dll error
After trying many things I finally removed all Apple software
iTunes
Apple Software Update
Apple Mobile Device Support
Bonjour
Apple Application Support
I was then able to finally successfully install the latest version of iTunes and the software installed correctly and the error went away.
I hope this works for you as well.

All of a sudden my iTunes stopped working, and I get the following error messages: 1. the program can't start because MSVCR80.dll is missing from your computer. Try reinstalling the program to fix this problem and 2. iTunes was not installed correct

All of a sudden my iTunes stopped working, and I get the following error messages:
1. the program can't start because MSVCR80.dll is missing from your computer. Try reinstalling the program to fix this problem
and
2. iTunes was not installed correctly. Please reinstall iTunes. Error 7 (Windows error 126).
Now I've checked the forums and followed the advice of uninstalling all Apple applications, rebooting, and reinstalling iTunes.
This is not working. I've tried installing as Administrator but doesn't make any difference at all.
There must be a way to fix this? I'm not a tech geek but I want to avoid having to take my laptop back to factory settings to sort this out.
Thanks

Click here and follow the instructions. You may need to completely remove and reinstall iTunes and all related components, or run the process multiple times; this won't normally affect its library, but that should be backed up anyway.
(99192)

NI-MAX/NVIORef.dll and RTE 8.2.x nightmare. pls someone sends me a RTE 8.2.1 dll?

Similar Messages

Maybe you are looking for