NI Scope Sorf Front Panel will not detect NI PXI-5122
Hello,
I am trying to use NI Scope Soft Front Panel 2.7f0 to acquire simple waveforms;
however it will not detect my NI PXI-5122. I have confirmed that the digitizer
works under MAX 4.2.1 and can see waveforms under the test panel. I have
installed NI Scope 3.3.1 on my machine and have updated the driver on the PXI
to version 3.3.1. Any ideas on what is wrong?
~Buck
It is unclear from your post whether or not the 5122 is on the same physical device as you are running the soft front panel (SFP). The SFP only works on local devices. It does not have the capability to attach to RT or remote systems (MAX does). However, if you are running Windows on your PXI controller or are using MXI to control the chassis, there is another issue.
This account is no longer active. Contact ShadesOfGray for current posts and information.
Similar Messages
-
MAX does not detect my PXI-5122 and PXI-6551 cards in a PXI-1045 chassis.
I have been using a PC with MXI-3 to PXI-1045 chassis to develop LabView TestStand code. Things are fine on my development PC. [Software configuration report attached nireport_rich.txt].
I have a 2nd PC set aside to test my deployment packages. I installed a GPIB card and MXI-3 card in my deployment test PC, and loaded a bunch of hardware drivers. [Report attached nireport_depPC_0006.txt]
All the PXI cards are found just fine when my development PC is connected, but when I power up my deployment PC (with MXI-3 connected to the 1045 chassis) -- I can't import the development configuration [exported from development PC] because the deployment PC does not see the PXI-6551 DIO card in slot 6 [PXI6::10::INSTR] and the PXI-5122 card in slot 13 [PXI8::15::INSTR].
I keep reviewing the hardware driver versions installed, and the only small difference that I see at this point is that the deployment PC has a slightly older version of NI-Switch.
Anybody have any ideas of what I can try next? I'm out of ideas.
. . . . hmmm, can't seem to attach more than one file, so here's the software info on the deployment PC
NI Software Information:
CVI Run-Time 7.0.0.395
NI-DAQ 7.3.0f1
NI-DAQmx 7.3.1f0
NI Script Editor 1.1
NI-DMM 2.3.1
Soft Front Panel 2.3.0
NI-FGEN 2.2.1
FGEN Soft Front Panel 2.2
NI-488.2 Software 2.30
IVI Compliance Package 2.2 2.2
LabVIEW Run-Time 7.0
Measurement & Automation Explorer 3.1.1.3003
Measurement Studio 6.0
For Visual Basic
ActiveX User Interface 7.0.0.344
ActiveX 3D Graph 7.0.0.344
ActiveX DataSocket 4.2.2.1
NI-USI 1.0.2
NI-HSDIO 1.2.1.3
NI-HWS 1.2.2.0
NI-PAL Software 1.8.2.0
NI-SCOPE 2.7.0f5
SCOPE Soft Front Panel 2.1.0
NI Spy 2.2.0.12
NI-SWITCH 2.30.49153
NI-TClk 1.2
TestStand 3.1
NI-VISA 3.2
visa32.dll 3.2.0.19
NiVisaServer.exe 3.2.0.19
NIvisaic.exe 3.2.0.19
LabVIEW Run-Time 7.1Hello Maggie,
Appreciate your assistance and reply.
The pxisys.ini and pxiesys.ini files are modified by me with referring to
1)PXI System Alliance PXI-2 SW spec,
2)PXI-6 SW spec,
and 3)pxisys.ini pxiesys.ini generated by MAX v5.3.0f0 with NI PXIe-1075 + NI PXIe-8133.
The content in pxisys.ini/pxiesys.ini generated by MAX looks like simple. Consequently, I modified and checked it line by line according to actual hardware of PXES-2590+PXIe-3975. Then, MAX just list devices as described in the first post. I tried to find the root cause but in vain.
Is this minor issue can be related any incorrect tag lines in pxisys.ini or pxiesys.ini I posted?
Is any suggestion tests I can do to troubleshoot root cause?
Looking forward your reply.
Cheers,
KL Tseng -
NI DMM Soft front panel did not detect any ni-dmm
Hello,
has anyone seen this failure? I can´t open soft front panel to setup the dmm. I tried to reinstall VISA and NI-DMM without success.
Thanks
Robert
Solved!
Go to Solution.
Attachments:
NIDMM FrontPanel_Failure.JPG 107 KBHello,
reinstalling the nidmm and visa will cause several reboots of the system. That was no solution
for me and my problem.
After starting the nidmm, the window with the information, that the 4072 won´t be found shows
a RESCAN button. By pressing the RESCAN button, the error code -1074118656 and the message,
that the device ist not recognized and this version or driver wont fit my 4072.
Should I install the only install the delivered driver or could I update to the actual version?
Delivered was Version 2.5 of NIDMM, installed on my system is the actual one from the NI homepage.
I think, I try to deinstall the NI-SW completely and install "only" the delivered SW. Hope, this will solve.
Robert
Attachments:
Error -1074118656.PNG 23 KB -
NI 5112 Scope soft front panel setting problem
Hi,
I tried to meausre a 5.1 voltage using SCOPE soft front panel. I could get 5.1 AC voltage from SCOPE soft front panel,
but it did not go back to 0 volt after 1 to 2 second in a horizontal line. Nornamlly, my 5,1V will go back to 0 volts
in my oscilloscope after 1 to 2 seconds because I am measureing a shock beep pulse waveform.
Can you tell why?
I am going to give you my setting. I was trying Y-axis 2 volt/div, AC coupe, ch 0, X-axis is 10 microsecond/div. normal mode.
Trigger: edge, rising, ch 0, trigger lever 2.5.
I am in a urgent. Coould you pls send me quicklyI'm sorry if I don't completely understand what the behavior is but if I understand you correctly, you have a signal that goes from 1 volt, peaks at 5.1, and then slowly drops to 1 volt again. That entire signal takes 1 to 2 seconds.
I am not sure if the problem you are seeing is 1. You can never get the full signal in the SFP or 2. You get the signal ok but the SFP does not wait for you to hit a button to try and acquire again.
If the question is number 1
If this is the issue it sounds like you are able to capture the 5 Volt peak, however it never goes back down to 1 volt. You mentioned that you have the X-Axis set to 10 microseconds/ div. Therefore the SFP is only acquiring an total of 100 microseconds, and if the reference is set to 50%, then you are only getting 50 microseconds of signal after the trigger, so you will not be able to acquire the 1-2 seconds it takes for your signal to drop. I would suggest increasing the number of points and slowing down the Time/Division. You should be able to change those settings a few times to actually get 2 seconds worth of signal.
2. If you want to simply hit a button and the SFP will acquire again then you need to change the mode to SGL. Then you just need to hit the run or pause button and the SFP will acquire again.
Message Edited by Evan on 09-12-2005 10:03 AM -
Front panel sound not working* Hello everyone,
I've just bought a PCI Express X-Fi Titanium. So far everything works great with my 5. sound system, but I have problems with my front panel audio.
My case only supports AC97 front panel audio, but has all individual connectors (so 7 single connectors, not one with 0 pins).
I've already tried only connecting 5 pins (the two AC97 return pins unconnected) and connecting all 7 pins. In both ways the microphone works, but sadly not the headphone output. I also tried changing the two options in the driver but that changed nothing.
I did some Google searching and found many reports where the sound itself works with an AC97 front panel on an HD soundcard, just no jack detection.
Any ideas why that isn't working for me?! Try here for pinouts of your jacks. I have a Cooler Master case that has AC97 and INTEL HD front panel jacks, but here is the kicker. The AC97 jacks come from the front panel first and then about fi've inches from this jack is an INTEL HD jack. A few wires are changed but perhaps these will help...
http://www.intel.com/support/motherboards/desktop/sb/CS-0585.htm
Cheers,
Jerry Macguire -
Scope soft front panel signal position
I'm using the new version of the Scope Soft Front Panel, 2.7f0.
How can I change the position of Ch 0 relative to Ch 1. When they are right on top of eachother, its not as clear. The older soft scope allowed them to be moved.
You can see in the attached picture that there is a little action cursor available as I hover over the channel designator on the left. But no action is available.
Anybody know how to do this? I don't want to use the offset values, because then I have to change the trigger levels as well
~~~~~~~~~~~~~~~~~~~~
Paul Johnson
Renco Encoders, Inc
Goleta, CA
~~~~~~~~~~~~~~~~~~~~
Attachments:
New Scope.jpg 146 KBThanks Raajot,
Unfortunately, the first method does not work. Seems like the channels
move together and can't be separated. However, changing to the classic
mode with the scroll bars works fine.
Its nice having the controls for both channels available in the new
mode, but I can't have the signals laying ont op of each other, so I
suppose I'll just have to stick with the old mode.
Does changing the vertical postion apply to only one channel on your
installtion? On mine, as soon as I pick a percentage, that same value
appears if I pick a different channel on the channel selector control.
Strangely enough, the menu method works fine in the classic mode. I
suspect a bug with the new mode. Otherwise, I'd be able to drag the
channel indicator in the new mode, similar to having scroll bars in
the classic mode.
~~~~~~~~~~~~~~~~~~~~
Paul Johnson
Renco Encoders, Inc
Goleta, CA
~~~~~~~~~~~~~~~~~~~~ -
HT1386 iTunes will not detect my iPhone(5s) after the most recent update.
Ever since i updated iTunes it will not detect my iPhone, every time i plug it in it asks to trust the computer which I always use to sync my iPhone. Every time i select "trust this computer" and it still won't detect it. PLEASE HELP.
Hello fercho965,
Sorry to hear that your iPhone is currently not recognized by iTunes. I found an article with steps you can take when you experience an issue like this. I wasn't sure whether you were using a Windows or Mac computer, so I included the respective articles for each:
iOS: Device not recognized in iTunes for Windows
http://support.apple.com/kb/TS1538
iOS: Device not recognized in iTunes for Mac OS X
http://support.apple.com/kb/TS1591
Thank you for using Apple Support Communities.
Best,
Sheila M. -
I have a VGA monitor plugged in to my imac using the VGA adapter to the mini-DVI. All was working well. Since I updated over the weekend, the computer will not detect the monitor.
Any ideas how to fix this?Pcantin wrote:
I have tried another VGA monitor and that failed as well. Since you don't think the update was the cause, it may be that the adapter I am using decided to call it quits. I will see if I can find another and test that out.
I will look into the external drive idea as well.
Thanks for your help on this.
I didn't think about the adaptor, but you should at least visually inspect both the adaptor and the cable at both ends. If one or more pins got bent even slightly the connection might fail. The cables can also fail internally. Replacing the adaptor and cable may be the quickest thing to do initially. If you want to try to save money, first replace the adaptor, and if the problem persists, then go replace the cable (or vice versa). -
I have done absalutely nothing to my 4g apple ipod touch, and it over heats, won't hold a charge, and the front camera will not work. I bought this brand new in december, and i've barely used it. I've tried restarting it and everything, I honestly think this is out raging because i spend over $200 on this. To have for music and instagram. I use it about an hour a day, but i've only been using it for about 3 months although i've had it since December. Any suggestions that may help me?
Try:
- A reset. Nothing is lost
Reset iPod touch: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Restore from backup
- Restore to factory settings/new iPod
If still problem make an appointment at the Genius Bar of an Apple store. -
On a windows 7, i finally got the Iphone4 setup so i can copy my pictures off of the phone. Know itunes will not detect the iphone to get it synced. how do i get it back to be seen by Itunes?
See earlier post by tt2
https://discussions.apple.com/message/7217190#7217190 -
IPod 4th gen grayscale will not detect usb connection.
Hello everyone, I have a iPod 4th gen grayscale and I'm running Ubuntu, everything has worked well for about a year now, I have been syncing my iPod through VirtualBox with Windows XP for as long as I have been using Linux, though, for some reason, my iPod has stopped noticing my usb being connected, I know it's not the usb cable, or the usb ports, I have restarted my iPod and put it into disk mode, still no luck, restarted my computer, Linux will not detect anything plugged in, nor will Windows, though my iPod shows the battery charging when plugged in, but iTunes will not detect the iPod.
I have switched the hard drive of the iPod out seeing if that was the problem, still no luck, my car dock will pick up the iPod and play music, so will my other docks, I thought it might of been Linux at first, so I plugged it into my desktop with Vista, it also will not detect it.
Does anyone have an answer to this riddle?A bad USB hub will cause the problem ... are you using it ??
-
HP installer will not detect networked LaserJet MFP M1536dnf just on some PCs
Hello,
this printer/scanner was working fine (printer still works fine via a Windows print server). Then scanning (via network) stopped working on one PC (Windows 7).
Tried to uninstall drivers / HP software and reboot. Then tried to install again - HP Installer will not detect printer on the network no matter what. I can ping the IP of this printer, access its web interface without any issues on the same PC. Tried specifying IP address in the installer - does not detect, the same issue with MAC address.
Had a Windows 8 machine with drivers / software installed on it, tested - scanning still worked fine on that PC. Tried to remove HP software to see if problem will appear. And it did! I cannot install the same software package which I still had in downloads - it will NOT detect the printer on network.
Upgraded printer firmware - no change, even though I don't expect this to be a printer issue as it worked fine until I have uninstalled software on this W8 machine.
Tried using HP Scan & Print doctor. That thing doesn't see printer/scanner installed and only suggest to download and install software which is not helpfull at all.
I also tried extracting HP installation files and finding *.inf files which could be used to add scanner via Windows directly, but haven't succeded with that (I would also be not sure how to specify network IP address in such a case anyway).
Any help is MUCH appreciated. We are kind of stuck...
Thanks!Hi,
Run some diagnostics and see if any issues are discovered.
There have been reported issues with the NVIDIA 650 with some of the HP PCs. Additionally, most models of the NVIDIA 650 require a 400 watt power supply as the minimum and some models require a PCI six (6) pin power connector which the 300 watt power supply in your PC is not provisioned.
There is a BIOS update posted for your PC so you might want to consider installing that update.
HP DV9700, t9300, Nvidia 8600, 4GB, Crucial C300 128GB SSD
HP Photosmart Premium C309G, HP Photosmart 6520
HP Touchpad, HP Chromebook 11
Custom i7-4770k,Z-87, 8GB, Vertex 3 SSD, Samsung EVO SSD, Corsair HX650,GTX 760
Custom i7-4790k,Z-97, 16GB, Vertex 3 SSD, Plextor M.2 SSD, Samsung EVO SSD, Corsair HX650, GTX 660TI
Windows 7/8 UEFI/Legacy mode, MBR/GPT -
The iCloud Control Panel will not intall on my WIN 7 32-bit PC
the iCloud Control Panel will not install on my WIN 7 32-bit PC. I receive the error message,
"There is a problem with this Windows installer package. A program run as part of the install did not finish as expected. Contact your local support personnel or package vendor."
When the panel finished being "backed off" my PC, I also received the following message,
"iCloud for Windows Installer Error.
The installer encountered errors before iCloud for Windows could be configured.
Your system has not been modified. To retry these operations at a later time, please run the installer again.
Click FINISH to exit the installer."
Each time I tried to download and install the Control Panel, these messages would appear.
The Genius Bar was unable to help me and referred me to the ICloud Support Line. They were unable to help me.
I refuse to believe that Apple is unable to solve this issue with their own software, but if there is anyone in this august community that can help me, I would be forever grateful,
Thank you.I'm having the exact same problem, and the exact same error messages. I have windows 8.1 64-bit. I've tried looking for solutions everywhere. I'm very frustrated.
-
My wifi is on and when it tries to find a wifi connection, the gray little circle just keeps spinning and will not detect our home wifi. I have tried to search for it and connect to it manually, but it will not search for the network name. I'm hoping I don't need a new phone so please help.
The following may have something that will help: http://support.apple.com/kb/TS1398
-
i just got an ipod touch but it will not sync to itunes. my itunes will not detect it. but my computer does. what do i do???
Start here:
iPhone, iPad, or iPod touch: Device not recognized in iTunes for Windows
Maybe you are looking for
-
Export error in Pages-"the file format is invalid" (Mavericks)
Hi there, as I have seen in prior discussions, this error has already been an issue in 2011, but the solution won't work any more, as the link is dead While the export still worked yesterday, it has ceased doing so today. The only exporting format af
-
Getting embedded video to pause at a certain point
Hello, I am using captivate 6 at the moment. Is there a way to automatically pause a video at a certain point - (to add for example a text caption) than automatically play again for example after a few seconds? Thanks Alison
-
Business Objects Lead or Architect position open in NJ -pls contact asap
<font color="#800000"><p>Hi,</p>My name is Fahima Hilal and I am a Recruiter . We are Tier one vendors to major Fortune 100 clients. I am contacting you, with regards to your resume being posted on the internet. We have an opportunity that I have lis
-
Marking albums to be excluded from automatic sync
Hello, Is there a way to mark albums / songs in itunes, so that they are excluded from the next automatic sync when i hook up my ipod? I like the auto-sync cause it's easy, but i just got some albums i don't really want on my ipod. I could just to th
-
Audio won't play in the Viewer but will in the Canvas from the timeline.
If I select a clip from the timeline to open in the viewer, I cannot hear the audio even though both video and audio are selected. This only happens in certain projects. Anyone know why?