NI Switch Executive error when attempting to add NI PXI-2566 switch to new virtual device.

I just loaded Switch Executive and am wanted to explore its capabilities. I have a PXI system that I am setting up. Currently I have PXI-2566 cards in slots 8 and 9.
I was following the NI Switch Executive help documentation "Creating a Virtual Device" and attempted to create a virtual device with the 2566 modules and I got this error;
Error xBFFA000A occurred.
Failure loading driver module.
The driver for the DAQmx switch is not loaded.[DeviceXI1Slot9_ivi]
Attachments:
SwitchExecutiveError_01.bmp ‏229 KB
SwitchExecutiveError_MAX.bmp ‏364 KB

I had not loaded the "NI-DAQ 7" software that came with the 2566 switch card. I assumed that since MAX showed that I had version 7.2 of DAQmx that I was already up to date.
I received a new PXI-2532 switch, and when I got a "driver not found" error in Switch Executive when I tried to add the 2532 to a new virtual device, I had second thoughts on running the setup/install from the new discs.
After running the software install, I was able to add the 2566 switches to a virtual device in Switch Executive. However, the 2532 failed.
Error xBFFA4B4A occurred.
DAQmx Error -200181 occurred:
Channel name specified is not valid for the switch device.
Device: PXI1Slot10
Channel Name: r4
Attachments:
SwitchExecutiveError_02.bmp ‏35 KB

Similar Messages

Error When Attempting to add a builder in Flex Builder 3

Hi All,
When I attempt to add a builder to my flex project, I get a "Internal Error: Unable to Save Launch Configuration" message. I was wondering if anyone knew how to fix this problem. A screenshot below. Also, there does not appear to be any error message written to the .log file in the .metadata folder.

Hi,
From your description, it seems that the address
sales@[domain].com has been used in another mailbox. I recommend you use the following cmdlet to find out which mailbox is using this address.
Get-recipient | Where {$_.EmailAddresses -match "[email protected]"} | select Identity, DisplayName, RecipientType. The mailbox which is using this address will show up in the result.
Hope this can be helpful to you.
Best regards,
Please remember to mark the replies as answers if they help, and unmark the answers if they provide no help. If you have feedback for TechNet Support, contact [email protected]
Amy Wang
TechNet Community Support

Hyperion Performance Scorecard error when attempting to add Accountab'y Map

Hi
I getting the generic error message -- "Performance Scorecard is having difficulty fulfilling your request. Consult your Performance Scorecard Administrator." -- when I attempt to add a new Accountability Map.
I am using the Balanced Scorecard framework and have so far defined the Framework, some Measures, an Employee and now want to define the Accountability Elements. Based on what I am reading in the documentation, I need to do this via the Add Accountability Map function -- correct me if I am wrong.
Any ideas on where I can look to see what is actually generating the error?
Thanks
Taha
PS. I am trying to get ready for a meeting later this week so need an answer as quickly as possible. Thanks

RESOLVED....SORT OF...
I requested a recycle of the environment and that seems to have fixed the problem. We are going to monitor and if it re-occurs will open an SR.

Error when attempting to add Oracle Text using DBCA

Hi all -
I'm trying to add Oracle Text to my 10gR1 database using DBCA. The Oracle Text option is available, but when I attempt to add it I get the error message: "A tablespace for the database option Oracle Text is not found. Cannot install this option in the database." I have a SYSAUX tablespace, which I believe is the default tablespace for Text, so I'm not sure what the problem could be. I also tried manually adding Oracle Text by running catctx.sql but received the error message:
ERROR at line1:
ORA-39705: component 'CONTEXT' not found in registry
ORA-06512: at "SYS.DBMS_SYS_ERROR", line 86
ORA-06512: at "SYS.DBMS_REGISTRY", line 757
ORA-06512: at line 2
Any ideas or suggestions would be greatly appreciated. Thanks!

Hi,
this looks like a half way install, I think you should try to deinstall Oracle Text and then reinstall, have a look at note 280713.1 on Oracle Support
Herald ten Dam
http://htendam.wordpress.com

ODBC driver error when attempting to add Region to a new Analysis

With MMASTERS login, attempting to do the demo script. When I try to add the Region from Accounts, get error code:
OPR4ONWY:U9IM8TAC:OI2DL65P
State: HY000. Code:10058 General error Session variable has no value.
I would like to know how to fix this, so I can present the demo to clients.l

Hi,
From your description, it seems that the address
sales@[domain].com has been used in another mailbox. I recommend you use the following cmdlet to find out which mailbox is using this address.
Get-recipient | Where {$_.EmailAddresses -match "[email protected]"} | select Identity, DisplayName, RecipientType. The mailbox which is using this address will show up in the result.
Hope this can be helpful to you.
Best regards,
Please remember to mark the replies as answers if they help, and unmark the answers if they provide no help. If you have feedback for TechNet Support, contact [email protected]
Amy Wang
TechNet Community Support

Strange error when attempting to add an article to the Folio Builder

I've just installed the trial of InDesign 5.5 along with the Digital Publishing Suite.
I've followed the instructions to add an article to the Folio Builder but I am continually greeted with this error:
Not sure what I am doing wrong, the document is set at 1024x768 and it's the first article I've tried to create. It's very simple, just a single image and some text.
I've tried installing on a seperate machine but I get the same error.
Any help would be appreciated.
Ryan

In some instances, InDesign isn't recognizing the new tools. To fix, restore InDesign preferences:
(Windows) Start InDesign, and then press Shift+Ctrl+Alt. Click Yes when asked if you want to delete preference files.
(Mac OS) While pressing Shift+Option+Command+Control, start InDesign. Click Yes when asked if you want to delete preference files.
http://help.adobe.com/en_US/indesign/cs/using/WSa285fff53dea4f8617383751001ea8cb3f-6d21a.h tml#WSa285fff53dea4f8617383751001ea8cb3f-6d1ba

"Frame Load Interrupted" error when attempting to add to Passbook

I just got a postcard from Ford Motor Co. announcing the new Mobile Member Card. To start, I had to read the QR code printed on the postcard using my iPhone. I was then taken to a page and directed to fill in my member number (on the postcard), e-mail and last name. I then clicked "Submit," and was taken to another page instructing me to click on the "Passbook" icon in order to add my new Mobile Member Card to my phone's Passbook. I clicked it, and got an error box: "Frame Load Interrupted." This happened to me three more times, even after I reset my Safari prefs. to "always" accept cookies. Is there a glitch in Passbook? Is it my iPhone? Have yet to upgrade to iOS7 for fear of losing functionality of many if not most of my apps--same reason I'm not giving up my iPhone 4S for a 5S. I am currently running the most recent update of iOS 6.1.
Please advise.

You are using VMM 2012 R2. What version is the cluster you try to add?
I have seen odd behavior when VMM 2012 R2 is running on Windows Server 2012, and not Windows Server 2012 R2.
What's happening then, is that when VMM is using Windows native powershell modules, it is using 2012 versions instead of 2012 R2, which doesn't goes too well with your cluster if that is 2012 R2.
Can you confirm whether this is true or not in your environment?
Also, you should investigate in the logs on VMM and the cluster to see if anything is not working as expected.
-kn
Kristian (Virtualization and some coffee: http://kristiannese.blogspot.com )

SharePoint Online switching to mobile view when attempting to add user permissions

Hello,
I am having a very weird problem that just started out of no where. It happens when I go to the Site Settings of my site collection and click on Site Permissions. When I click Grant Permissions to try to add users, the browser will immediately switch to
the mobile view.
I am able to switch back to the regular browser view, then when I click Grant Permissions, the box to select the user opens. I then choose the user and click Share. After clicking Share, the popup immediately goes to the mobile view. When I exit that the
users were never granted permissions.
This only happens so far when I am trying to add permissions. Is there something that I could have messed up?
What is happening and how can I fix this? I am out of ideas and unable to add permissions for users. I do not want to have to blow this site collection away.
Thanks.

Hi Andy,
According to your description, my understanding is that the page would switch to mobile view when attempting to add user permissions in SharePoint Online.
I recommend to verify the things below:
Clear the caches in browser to see if the issue still occurs.
Test the same scenario in another computer to see if the issue still occurs.
Append mobile=0 to the URLs in SharePoint Online.
In the meanwhile, you can post your question to the forum for SharePoint Online: http://social.technet.microsoft.com/Forums/msonline/en-US/home?forum=onlineservicessharepoint.
More experts will assist you, then you will get more information relation to SharePoint Online.
Best regards.
Thanks
Victoria Xia
TechNet Community Support

Photosmart Plus B210 - Error Message when attempting to add printer

When attempting to add our Photosmart Plus B210 on a computer with Windows 7, we get the error message: "Active Directory Domain Service is currently unavailable". We have installed the drivers from the disc and have attempted both USB and Wireless installation--neither have been successful. We have uninstalled and reinstalled mulltiple times as well as followed another forum suggestion to run msconfig and change startup to diagnostic, etc. HP Print & Scan doctor has not helped resolve. Any ideas out there?

Hello felenti,
Please let me take a moment to say "Welcome" to the HP Forums. I hope you enjoy your experience!
To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More.
I see that you are having some issue with the installation of your printer to your computer. I also see that you have ran the HP Print and Scan Doctor and it did not resolve the issue.
One step that I do suggest we try is to run the HP Printer Install Wizard for Windows.
Please write me back with the results of the Wizard.
If I don't hear back from you today, I hope you have a Great Wednesday.
Cheers,
Click the “Kudos Thumbs Up" at the bottom of this post to say “Thanks” for helping!
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
W a t e r b o y 71
I work on behalf of HP

Switch Executive Error -1074130544

An operation is getting the following error when attempting to make a NISE connection. He is running a sequence in TestStand 4.0 and using the switching properties of the step. This is the first switching operation in the test sequence.
An error occurred while performing the switch operation 'Connect' for the following device '265869_T45_LED_Driver'. Could not perform the switching operation: Details: (IVI Error Code: BFFA1190) [Device: NI_PXI-2532_ivi](Error = -1074130544) [Error Code: -17500, Operation Failed.]
I cannot find any information on any of the above error codes. What exactly does this error relate to?
I am using TestStand 4.0, and NISE 2.11
Thanks,
Paul Holzrichter

Hey kwseitz3 and Paul,
After doing some more testing on
our end, we believe that this might be a separate bug and would thus
warrant a separate CAR to be filed. Do you still have the NI Spy
captures from: 1. using Reset and 2. using Single Pass? You also
mentioned that it worked just fine when you ran your test without
hardware so it would also be helpful if you could get us NI Spy
captures for Reset and Single Pass for this scenario as well.
One last piece of the puzzle that would help us would be your Switch
Executive and IVI configuration information. For Switch Executive you
could just export your configuration from MAX and for IVI you can copy
the IVI configuration store file. Both of these should be .XML files.
NISE Configuration: In MAX, right-click Switch Executive Virtual Device, select Export. Send this file.
IVI Configuration: Click on IVI Drivers to find the Master IVI
Configuration Store Location. Send the IviConfigurationStore.xml file.
I went ahead and attached screenshots of where you can grab these files.
Do you think either of you could get us these files so we can further isolate the
cause of this issue?
Attachments:
NISE Configuration.JPG ‏65 KB
IVI Configuration.JPG ‏49 KB

Error when attempting to IMPORT object "TS_CHECK".

When using in BI SAP NetWeaver 2004s (700 - SP 15) the transaction ST04old -> Detail analysis menu -> Summary report
The following short dump occurs:
Runtime Errors         CONNE_IMPORT_WRONG_COMP_TYPE
Except.                CX_SY_IMPORT_MISMATCH_ERROR
Date and Time          19.11.2008 15:14:08
Short text
Error when attempting to IMPORT object "TS_CHECK".
What happened?
Error in the ABAP Application Program
The current ABAP program "SAPLSTD4" had to be terminated because it has
come across a statement that unfortunately cannot be executed.
Error analysis
An exception occurred that is explained in detail below.
The exception, which is assigned to class 'CX_SY_IMPORT_MISMATCH_ERROR', was
not caught in
procedure "DB02_ORA_FILL_TS_CHECK__CRITOB" "(FUNCTION)", nor was it propagated
by a RAISING clause.
Since the caller of the procedure could not have anticipated that the
exception would occur, the current program is terminated.
The reason for the exception is:
When importing the object "TS_CHECK", the component no. 4 in the
dataset has a different type from the corresponding component
of the target object in the program "SAPLSTD4".
The data type is "I" in the dataset, but "N" in the program.
Missing RAISING Clause in Interface
Program                                 SAPLSTD4
Include                                 LSTD4U03
Row                                     1
Module type                             (FUNCTION)
Module Name                             DB02_ORA_FILL_TS_CHECK__CRITOB
Trigger Location of Exception
Program                                 SAPLSTD4
Include                                 LSTD4U03
Row                                     51
Module type                             (FUNCTION)
Module Name                             DB02_ORA_FILL_TS_CHECK__CRITOB
Source Code Extract
Line
SourceCde
21
DATA: BEGIN OF TD110.
22
INCLUDE STRUCTURE TD110_STRU.
23
DATA: END OF TD110.
24
25
CURR_TIME = SY-UZEIT.
26
CURR_DATE = SY-DATUM.
27
28
CALL FUNCTION 'GET_DB_ORA_RELEASE'
29
IMPORTING
30
ORACLE_RELEASE = ORA_REL.
31
32
IF FLAG_REFRESH = 'y'. FLAG_REFRESH = 'Y'. ENDIF.
33
flag_refresh = 'Y': Es soll in jedem Fall auf die DB zugegriffen werd.
34
35
CLEAR TS_CHECK. REFRESH TS_CHECK.
36
CLEAR CRITOBJ. REFRESH CRITOBJ.
37
CLEAR NR_CRIT_OBJ.
38
39
IF FLAG_REFRESH <> 'Y'.
40
41
Suche zunächst im Arbeitsspeicher !
42
CLEAR TS_CHECK_CACHE. READ TABLE TS_CHECK_CACHE.
43
IF NOT ( TS_CHECK_CACHE IS INITIAL ) .
44
TS_CHECK[] = TS_CHECK_CACHE[].
45
CRITOBJ[] = CRITOBJ_CACHE[].
46
OK_1 = 'Y'.
47
48
Suche danach in 'MONI' !
49
ELSE.
50
PERFORM PREPARE_MONIKEY USING 2.
>>>>>
IMPORT TS_CHECK CRITOBJ FROM DATABASE MONI(DB) ID MONIKEY.
52
53
IF SY-SUBRC = 0.
54
OK_1 = 'Y'.
55
TS_CHECK_CACHE[] = TS_CHECK[].
56
CRITOBJ_CACHE[] = CRITOBJ[].
57
ENDIF.
58
ENDIF.
59
60
'Same procedure' für datetime:
61
IF NOT ( TD110_CACHE IS INITIAL ).
62
DATETIME-MONI_DATE = TD110_CACHE-DATUM.
63
DATETIME-MONI_TIME = TD110_CACHE-UZEIT.
64
ELSE.
65
PERFORM PREPARE_MONIKEY USING 3.
66
IMPORT TD110 FROM DATABASE MONI(DB) ID MONIKEY.
67
IF SY-SUBRC = 0.
68
DATETIME-MONI_DATE = TD110-DATUM.
69
DATETIME-MONI_TIME = TD110-UZEIT.
70
TD110_CACHE = TD110.
Only related SDN post is following, but solved by changing permissions for saposcol.
Only related SAP Note is SAP Note Number 597743 "DB02: Poor entries for critical objects list", but not applicable for current SAP version.
For me strange is that this issue occurs on the development system, but not on the acceptance and production system.
Thanks in advance for any assistance.
KR
Gidion

Received the solution from SAP Active Global Support:
This error occurs due a corruption in the table MONI.
For solving this issue you need to clean the records of this table via the following path :
1. Call transaction ST03
2. With GOTO -> Performance database -> Content of database
3. Push button Delete data group
4. Enter ID DB
5. Continue
6. Confirm the delete
If you wish to backup the data before deleting the entry please follow the steps in the note 1000275 "DB02: history data backup procedure".
Regards,
Gidion

Error when trying to add printer on USB Print Server

I'm attempting to connect to a Canon MP530 printer via a Netcomm NP3680 USB Print Server.
When attempting to add the printer via the Print & Scan process, the USB port is seen by the MacBook and listed - ie: mini_me-3-usb2, and the driver is selected automatically without any problem after gathering printer information, however the macbook is unable to connect and returns the error: "An error occurred while trying to add the selected printer."
If a manual configuration is attempted the message returned is: "An error occurred while trying to add the selected printer. Unable to communicate with the printer at this time." Further manual config via the IP address will allow the printer to be entered, however the printer is non-responsive.
I have setup this printer via the same Print Server on the same Macbook prior to this and it setup and worked correctly - the same setup is working correctly on my wife's macbook. However I had to remove the setup on my Macbook and can't get the printer functioning again on this particular Macbook, or my son's.
The direct connection setup via USB directly works without any problem at all.
I'm currently running OSX 10.8.1, however my son is running 10.7.x and has the same problem. My wife's macbook is also running 10.7.x and is working fine.
Can anyone throw any light on this issue - it is truely frustrating, especially when I know it has worked in the past.
thanks very much in advance
GDT

After 55 views and 0 replies, and a number of calls to Applecare (without success) , I decided to once again troubleshoot the problem.
Fixed!
Bearing in mind, I had no other printers already set up in the Print and Scan window....
I removed the following items from the /library/preferences directory:
"com.apple.print.makequeues.plist",
"jp.co.canon.ij.print.filter.raster2canonij.plist",
"jp.co.canon.ij.print.utility.command2canonij.plist",
"org.cups.printers.plist"
I also removed all items from the /library/printers directory (including Canon, PPDs, plist files and icons)
Then I retried to install the printer..... (holidng my breath) and the Console showed:
Repairing access permissions of "/Library/Printers/InstalledPrinters.plist"
All is fine now

When attempting to add an event to my calendar and I press "done," I receive a message that reads "Cannot Save Event." "That event does not belong to that event store." What can I do remedy this issue?

When attempting to add an event to my calendar and I press "Done," I receive a message that reads "Cannot Save Event," "That event does not belong to that event store." How do I remedy this problem so I can add events and appointments to my calendar?

i am having the exact same problem, same messages (no end date set; cannot save; no calendar set; event does not belong to that event store."
it is unbelievable to me that this issue existed so long ago and hasn't been fixed. I just bought my first apple product (iphone4s) and am ready to toss it. Despite hours of searching on these forums I have been unable to find out how to fix my calendar. I have rebooted, adjusted settings to no avail. without a calendar, i can't use this product. Also, i am not technologically brilliant and can't handle the advanced fixes that some people recommend.
question, is apple a product for the ignorant like me? or should i go back to nuts and bolts pc?
all i really want is to be able to use the calendar without "uploading, reprogramming, contacting support offices for 3 hours, contacting network administrators, upgrading, switching fonts, changing operating systems.... etc. " I am just a regular person who needs a portable calendar.
sorry to vent, but can anybody tell me (in simple terms) how to get my calendar to accept a simple apointment?
thank you.

"Capture Device Offline" message when attempting to add additional clips from HDV Videocamera,in CS5

"Capture device off line" message when attempting to add additional clips to existing project in Premiere Pro CS5.5.2.
Previous capture was accomplished, but, then when trying to add additional clips from same device it failed.
All 40 minutes of some 185 clips was originally captured using Sony Vegas Moviemaker Platinum 11, with no errors. The additional mt2 clips were then successfully imported into Premiere Pro after indexing and conforming the clips, and they play perfectly well and of a high quality in CS5.5.2 at 1440 x 1080i.
Why would the Capture device be off line , when no physical alteration has been made to the equipment ?

Hi Joe,
Thanks for the advice but, the splitter may not help here, now Sony Vegas Movie Studio Platinum 12 which we also use for less complicated editing is now saying Canon HDV Camcorder is also "OFF LINE"
I think it is a physical connection issue either with the cable , the output from the camera or input into the laptop, because it was working. The issue has been intermittent making it difficilt to diagnose. We use it only for back up as we are overseas and do not have access to our main computer. The tapes are good and the video is high quality so I will have to wait worse luck, and the technical back up for HDV in Belgium is non existent as they have no computers in the stores that have the Firewire or I33394 card.
I have not changed any settings, I may have to wait till I get back to base in 10 days, I am also having an issue with a lens on the Canon 5 D Mark II, which I know must go back to Service but, it still works and, has issues after I dropped it ??????????
Message was edited by: Bob Dix Photographer

Error when attempting to import object C1

Hi,
We are doing an ECC 6.0 Upgrade from 4.6C version.
While executing Payroll Simulation, we are getting short dump error stating Error when attempting to import structure C1.
This error occurs in the Payroll driver RPCALCX0.
Requests for your inputs.
Regards,
Ravi.

'The data type is "N" in the dataset, but "C" in the program.'
Rob

NI Switch Executive error when attempting to add NI PXI-2566 switch to new virtual device.

Similar Messages

Maybe you are looking for