NI-USRP 14.0 driver ,and labview 2013 64 bit

Hi
Is it possible to use the NI-USRP 14.0 (64 bit driver) with Labview 2013 64 bit ?
have someone tried to install NI-USRP 14.0 drivers and then convert the driver ("instr.lib \niUSRP" directory) back to 2013 version ?
or do i need to purchase the 2014 version if i want to run 64 bit labview & USRP?
Thanks

Hi again
i installed the 32 bit verision of niusrp 14.0 driver (selected to install the driver for labview 2013 ,32 bit version)
& copied the installed files from 32 bit labview directories to the 64 bit version directories
, when opening a usrp vi (like "open rx session.vi" ) it says :
"error loading "niusrp.dll" A dynamic link library (DLL) initalization routine failed.
if i then try to point to another niusrp.dll like the one placed at C:\windows\SysWOW64\ , i got :
" the library selected is not valid for the current platform. for example ,you are running 64 bit labview and the library might be a 32 bit library"
where can i find the "right" niusrp.dll ?
so it seems that the niusrp 14.0 driver does not support labview 2013 64 bit version, ?

Similar Messages

Camera Vision Loop Snap will be 1% right and left inverse in Vision2013 and Labview 2013.

Hello,
I use a Camera to Loop Capture Vision Snap in Vision2013 and Labview 2013.
(see the right-up picture that is the needle in the right side, but the right-down picture it is in the left side.)
The right-up picture that is the current snap image shows normally.
The right-down picture is after en-queued and de-queued image.
But the image will be 1 % Randenly Chance to show right and left inverse.
Could someone tell me how to solve the problem?
Thanks.
Attachments:
IMAQ_Mirro_)_(.JPG ‏149 KB
IMAQ_realtime_image_snap_queue.JPG ‏196 KB

Good-day.
2 Cameras are both the same "AVT GUPPY F033B" , Connected to the IEEE1394 interface PCI Card (2 ports, Controller Chip is Texas Instruments).(See" cam_driver.JPG")
Both Cameras are 1 % Randenly right and left inverse.(See" IMAG_Mirro_)_(2.JPG")
The Labview 2012 program is the attached file called "IMAGE_LOOP_SNAP_Queue As a Multiplexer_LV2012.vi.zip"
Thanks.
Attachments:
cam_driver.JPG ‏55 KB
IMAQ_Mirro_)_(_2.JPG ‏159 KB
IMAGE_LOOP_SNAP_Queue As a Multiplexer_LV2012.vi.zip ‏769 KB

Solidwork x64 and labview 32 bits compatibility?

Hello community.
I'm with a project where I want to make the connection with Labview 32 bit and 64 bit Solidwork to control motors with LabVIEW, I have been following many tutorials and I get to create everything you need but when you run the VI does not move nothing SolidWork thousand times and reviewed the steps and is desesperate. Ruling out any option and I wonder if these two shows are 32 and 64 bits can be the cause of not getting the communication with these two programs. I hope your help. regards
Es un placer echar una mano siempre( Base de una sana convivencia). Si mi respuesta te sirve por favor agradecemelo con un Kudo
Un especial saludo a mis hermanos latinos. Un mundo mejor es posible.

Does this help?
http://digital.ni.com/public.nsf/allkb/71E9408E6DEAD76C8625760B006B6F98
Q. Can I run an executable built with LabVIEW 64-bit on a 32-bit PC?
A. You cannot run the LabVIEW 64-bit Development System, Run-Time Engine, or executables on a 32-bit PC.
Q. Can I run an executable built with LabVIEW 32-bit on a 64-bit PC?
A. Windows can run 32-bit executables on a 64-bit PC. Therefore, the LabVIEW 32-bit Development System, Run-Time Engine, and executables can be run on Windows 64-bit.
Q. Can I have both LabVIEW 32-bit and LabVIEW 64-bit installed on the same 64-bit machine?
A. Yes.
Q. Can I build a 32-bit version of an executable from the LabVIEW 64-bit application builder?
A. There currently is not an option to create a 32-bit version of an executable from the LabVIEW 64-bit application builder.

Report Generation Toolkit failure with Win 7 and Labview 2013

I recently had my computer updated to Windows 7 and am now seeing a problem with the Report Generation toolkit (version 2013) when working with Excel files. If I try to run the New Report.vi with report type Excel selected I get error -2146777998. Doing the same thing with Word selected eventually opens Word, although this takes about ten seconds, but it does not generate an error. Selecting Standard Report or HTML also run without errors.
I've researched this error on line but I keep ending up .NET and C# forums where everything goes over my head. Has anybody got any suggestions?
Solved!
Go to Solution.

I found the solution to this particular source of error code -2146777998. There are two template files that reside in C:\Program Files (x86)\National Instruments\LabVIEW 2013\templates\Report by the name of MSOffice_RGT_Template.dot and MSOffice_RGT_Template.xlt. The problem came down to that these templates got corrupted somehow during the fresh install. As soon as I replaced them with versions from another machine the problem disappeared.
Just as a side note, I discovered the problem by kicking off the MS Office Report Express vi and out came a much clearer message that aimed me at the templates. Not quite sure why that message isn't echoed into the individual subvi's on the pallette, but life is a mystery.

Integrating an NI-USB 8451 driver and Labview Run-Time Files in an installation package of a .vi application

Hello,
I've built a .vi which uses the NI-USB 8451 device (please see http://sine.ni.com/nips/cds/view/p/lang/en/nid/202368), and I would like to create an installation package to be used on a costumer's PC, which has no Labview installed on or a driver for this device.
I would like to have this installation as a completely stand-alone setup, so that the user could take this file and run it, and have the driver to the 8451, the run-time files for the Labview application installed by themselves, and have the .exe file working on a completely "clean" PC.
How can I integrate it all in one package ?
Thanks,
Michael.

Nice hearing from you again, Ipshita
I do not call any dll's currently, but am using the driver of the USB device, NI-USB 845x, version 1.0.1
Now, I would very like to make the use of my application, by another user, with no Labview or this driver on his PC, as simple as possible.
I just thought that maybe I could create an .EXE file with some Labview created dll's, which this executable would use, and spare the need of the 845x Driver or Labview Run-Time library prior installation. I could be wrong.
What should I do ?
P.S.
Meanwhile, I've been playing with the Application Builder and tried to create an installation with the Driver and the Labview Run-Time.
It had started the compile, but stopped with the following pop-up window: "Locate the 'NI-845x Software 1.0.1' distribution. Labview needs to copy a component installed or updated by the distribution..."
(Attaching the pop-up window below)
What is it looking for and where can I find it ?
Thanks,
Michael.
Attachments:
Installation_pop-up.JPG ‏20 KB

Windows 8 and Labview 2013 FPGA

I installed Labview 2013 including the FPGA design suite on a Windows 8 (x64) host. I was surprised to see Windows 8 on the list of supported OS as I was aware that up to this day no Xilinx design suite supported Windows 8.
But as a matter of fact it didn't took long before I hit:
ERROR: Simulator:861 - Failed to link the design
following this tutorial while clicking on check syntax (using one of the VHDL file provided with the tutorial). The error is clearly linked to a lack of Windows 8 compatibility from the XIlinx tools running underneath. Is there a known workaround? Thanks.
Solved!
Go to Solution.

That I could do but Linux is not listed here ... but Windows 8 is listed as supported for the farm server and not for the development environment. Isn't is the other way around? On top of that it looks like we should read GB instead of MB for the farm toolkit.

DC Motor Control - AKD Drive and LabVIEW Softmotion

Dear all,
I need to control a DC motor, which basicly has to rotate from -15 degrees to +15 degrees with changeable frequencies/time period.
The motor is used for inducing vibrations, thus the frequency and positioning must be (easily) controlled in LabVIEW.
My setup looks as follows:
cRIO 9082, NI 9514 C-Module, AKD Servo drive and an AKD DC Brushless motor.
Until this point i have used a "Contour move block - repetitive" for controlling the engine using a table, however, this doesn't allow me to configure velocity and acceleration etc. Furthermore, I don't know what units the block inputs are (radians, degrees, units/rotations whatsoever) - See pictures for details on diagram and setup.
Also, i would like the possibility to actually see and/or control a PID-controller using the feedback option.
So, i short, i basicly want to:
- Control the positioning of my DC motor (from -15 to +15 degrees).
- Control the motor using a PID controller (not necessarily needed, but i would like the possibilty)
- Control the velocity, acceleration, deceleration and frequency/time period.
Thanks in advance - looking forward to some good answers!
Have a great easter holiday.
Best regards,
Jzaulich
Attachments:
Motion and error.PNG ‏20 KB
Project tree.PNG ‏22 KB

Hi Anders,
Thanks for your reply.
I have the softmotion module installed and working - thats not the issue.
However, at the moment i'm using the "countour move" example provided with the SoftMotion module.
It works fine, however, it doesn't allow me to change the system too much and the unit of the input is not denoted anywhere (radians, degrees, revolutions etc.).
As i am all new to both LabVIEW and SoftMotion there's obviously a lot of obstacles.
I would like to model the motor control using a PID regulator with the position as input - is this possible, without making it too complex?
Best regards,
JZaulich.

Fieldpoint and Labview 64 bit - why is the LabVIEW Support missing from MAX and the Measurement I/O Pallette?

I am running Labview 2010 on a Windows 7 virtual Machine, I have installed Fieldpoint 6.0.7 with all the appropriate support. The VIs are in vi.lib. BUT, MAX doesn't show the LabVIEW support as existing, and the Measurement I/O pallette doesn't have the Fieldpoint VIs linked into it.
Anyone out there with any idea what I might need to do to get these seen? I've uninstalled, re-installed, installed only sections, and so far - no sign of these VIs appearing.
So, any ideas?

Not quite. I can see Fieldpoint, but not the LabVIEW support section.
The first screenshot is from my 32-bit system, the second is the one from the 64-bit system.
Attachments:
Fieldpoint Screenshot 1.JPG ‏20 KB
Fieldpoint Screenshot 2.JPG ‏15 KB

Compatibilidad de driver 845 para daq 8451 para labview 2013

Estoy intentando instalar el driver 845 para poder emplear la daq 8451 para un proyecto pero se diseño empleando labview 2011 y actualmente tengo el 2013, al momento de intentar instalar el driver más nuevo me aparece un error debido a que tengo un software más reciente y no se intala generando que al momento de querrer utilizar el proyecto busca el driver para actualizarlo y no llego a nada.
No se si alguien conosc la forma de poder instalar el driver para labview 2013.

Hola Artama,
Gracias por utilizar los foros de National Instruments! Que versión del driver 845x estabas instalando? Que error es el que te aparece al tratar de instalar? Te envío la liga de la última versión del driver (2.1.2 agosto 2013):
http://www.ni.com/download/ni-845x-2.1.2/4141/en/
Podrías descargarlo e intentar nuevamente con esta versión? En caso de que te siga apareciendo el error te agradecería si pudieras adjuntarlo en tu respuesta.
Saludos!

LabVIEW 2013 Patch f2 update problem

I have installed LV 2013 (13.0.1f1) Patch f1 (32-bit). I tried to install NI LabVIEW 2013 f2 Update but I got error message: "NI LabVIEW 2013 must be installed before you can install this update."
So, why it doesn't recognize installed app?
BR,
Jick

There is a difference between
LabVIEW 2013 f2-Patch and
LabVIEW 2013 SP1 f2-Patch
Choose the right one.

I cannot see the NI-DAQmx icon in measurement window in Labview 2013 (student Edition)

Hi All:
I have installed NI-DAQmx and Labview 2013 (Student Edition). I have connected an NI USB-6008 DAQ and tested it using NI-DAQmx and it is working properly.
Now I tried to do logging of data from this device using the installed Labview software but as I open a new project and go to Block Diagram screen and display the measurement menu I cannot see the NI-DAQmx icon in the measurement window (Menu) within Labview 2013 (student Edition).
Any suggestion?
I am attaching two screen shots.
Please help.
Thanks
Solved!
Go to Solution.
Attachments:
1.png ‏77 KB
2.png ‏88 KB

In which order did you install the software packages?
You should install LabVIEW first, followed by DeviceDrivers!
Best regards,
GerdW
CLAD, using 2009SP1 + LV2011SP1 + LV2014SP1 on WinXP+Win7+cRIO
Kudos are welcome

Usrp driver 1.3 do not support for Labview 2013 64 bit ??

Hello, dear all
Is anyone install the latest USRP driver 1.3 for LV 2013 64 bit ? I found there is no version for 64 bit LV 2013.

Currently the 1.3 driver supports only LabVIEW 2013 32 bit (even on 64 bit computers.)
The LabVIEW 2014 version will support 64 bit and will be available to download very soon.
Please check here within the next week or so: http://search.ni.com/nisearch/app/main/p/bot/no/ap/tech/lang/en/pg/1/sn/ssnav:drv/q/usrp/

Driver install don't detect Labview 2013

Hello,
After installing Labview 2013 (32bits) , installing driver (Daqmx,etc...) (DVD feb.2013) , application driver don't detect labview 2013, and doesn't want install anything.
Do you know this problem ? and how can i fix ?
Thanks.
Ludovic
Windows 7 32bits
Labview 2013 Eng 32bits
Devices drivers DVD4 feb.13 (also try with Aug12 version)

Hello,
Thanks for answer,
I can't find link for download devices drivers August2013... Exist ?
(@Julien..) Your download link is Labview 2013 download application, but don't contain drivers (i.e. DaqMx)
In other link for download Labview (2013), ( https://lumen.ni.com/nicif/confirmation.xhtml ) recommended download devices drivers is August 2012 ... (http://joule.ni.com/nidu/cds/view/p/id/3145)
Best regards
Ludovic

Problems with Labivew 2013 / 14 install - Ni Variable Engine error and Labview does not close, processes do not stop when I run Vis.

Hi All,
I am hoping at all my problems are relateded to a problem I am experancing, when I look into my windows 7 (64bit) event viewer near every time I boot up I get an error regarding the NI Variable Engine which reads.
The description for Event ID 0 from source NI Variable Engine cannot be found. Either the component that raises this event is not installed on your local computer or the installation is corrupted. You can install or repair the component on the local computer.
If the event originated on another computer, the display information had to be saved with the event.
The following information was included with the event:
C:\Program Files (x86)\National Instruments\Shared\Tagger\ni_tagger_plugin_mxs.dll: Failure to load plugin: Unexpected Error: Unable to get the Interface from the plug-in.
and a second which is the same apart fomr the last line
Unable to load the MXS configuration plugIn: Failed to get MAX Configuration interface for Tagger: 0x80040318
I have tried uninstalling all labview things and I have tried repairing all labivew programs. Along with this I got this error when I installed Labview 2013 so I thougth why not try 2014 and I still get the same problems. I also shoudl point out I use bot 32 bit and 64 bit versions of labivew. I have installed labview on many machines before but never encountered this problem. That being said this was a new clean windows install.
Along with thiese errors labview heardly ever shuts down properly when I close the program it just freezes and needs forshed shut down.
Apart form this I noticed that when I run any of my Vis which I have never had problems with in the past and I stop the program somtiems processes keep using CPU such as "lktsrv.exe"
I really need to get this sorted out because its morstly the crushing and processes not stopping which is rather annoying.
I shoudl also say that these problems are both in the 32bit and 64 bit versions of labview not difference. and no difference if its 2013 or 2014
Cheers

Hi GajanS,
Thanks for your reply sorry I havetn noticed anybody had replied as I stopped hoping for any responce before then.
I have attached a screenshot of the four processes that seems to be giving me a problem.
I have actually managed to find the program causing labivew to crash was in fact my antivirus software which I have now removed and have no more problems with labview crashing on shutdown.
After removing it I tried the repair feature again for all my labview programs but sadly the one persistant problem remaining is still the four processes using around 13% processor each. I have found out this happens sometime after booting up regardless of if I run labivew or not. So it does not directly seem related to the running of any labview applications but rather a bug in the labview software.
the processes are:
lktsrv.exe
tagsrv.exe
nidmsrv.exe
lkads.exe
as shown in the task manager.
I would relaly help if I can get this sorted out.
Cheers
Attachments:
Screenshot 2015-03-24 21.50.00.png ‏12 KB

Agilent Driver Causes LabVIEW to Blow Up and Stop

I have started to use the AG6000A driver for LabVIEW. It seems to work fine until I do a "Text" search and only on specific drivers. When I search on the "Acquire Multiple Waveforms Example"for any text, the LabVIEW application ends suddenly causing a loss in any work that is being performed. Anyone else have this problem?
I am using LV 8.5 on a 32 bit Windows XP OS.
Thanks.
Michael
Solved!
Go to Solution.

The driver I found at http://sine.ni.com/apps/utf8/niid_web_display.download_page?p_id_guid=0D3F5F0998FE61CAE0440003BA7CCD... and I selected version 8.0. However, I also found this driver:
http://sine.ni.com/apps/utf8/niid_web_display.download_page?p_id_guid=1E5E6D70FCA569A3E0440003BA7CCD... and I selected version 8.2.
I downloaded the 2nd driver and had no problems and them I download the original driver and again had no problems. All is well now. Something must have happened when I added the driver to the LabVIEW instr.lib folder. Anyway, sorry to bother.
Michael

NI-USRP 14.0 driver ,and labview 2013 64 bit

Similar Messages

Maybe you are looking for