NI WSN 3212 takes incorrect measurement with external power

Hi, all.
I have a problem with temperature measurement using NI WSN 3212 node with external power supply. The value randomly changes for all four channels. It happens if at least one thermocouple connected to any channel. If I disconnect all thermocouples, the values of channels are NaN. I have not this problem when node powers by battery.

Hi,
1. Check for the correct power cord that you have attached with the node to give the external power.
2. Check for any external power supplied to the channels from your side.
3. Reboot the node and try to obtain the temperature from thermometer.

Similar Messages

  • How much time ipod needs to restore after plugging with external power?

    how much time ipod needs to restore after plugging with external power?

    Restore? Do you mean power on after it's been drained for awhile? It depends how long it's been dead. Sometimes it can take awhile (10-20 minutes maybe more) in some cases.

  • I have new hard drive in macbook pro(08) and have SATA cable with external power source to old hard drive (10.5.8)via. USB port and newer drive(10.6.8) will not recognize older drive..Do I need to partition newer drive with older disk to recover data?

    I have new HD 750GB Hybrid in 2008 Macbook Pro 17" w/ Snow Leopard 10.6.8  connected to old Hard drive(250GB that had 10.5.8 on it at time of failure) via SATA cable to USB port with external power source.. Computer not acknowledging old HD at all in Disk Utility or otherwise (that I'm aware of)..Do I need to partition New HD and load old(10.5.8) onto partition to recognize older drive for data recovery? Thanks Wayno08

    You do not need to load 10.5.8 onto your new drive in order for a 10.6.8 system to see the contents of a 10.5.8 system.
    You might want to check out the hard drive troubleshooting bootk in the downloads section of this web site:
    http://scsc-online.com
    They also sell a product named Phoenix that can do OS extraction  and volume copying/cloning, but to be honest I don't know if it's appropriate in this case.
    I would suggest the following:
    Open up Terminal.app (under utilities) and type "diskutil list" without the quotes. This is the command line version of Disk Utility. If the external drive doesn't show up at all, then it's likely not connected properly, not getting power, or just plain dead. If it shows up with only a devce name like disk0s16 but no volume it means the drive is seen, the OS just can't make sense of it.
    Assuming the drive shows up, I would try to boot off the original installl disks for the system and run Disk Utility from that. I'm assuming the drive will show up. You'll want to select the option to repair the drive and then perform the option to repair the permissions.
    If the unit isn't showing up, as per step 1, try a different USB port. More importantly with your unit, try it on another side of the unit if possible. If you read the book I referenced above, some of those units have I/O boards that are separated from the logic board. If the cable from the logic board to the I/O card goes bad or has problems, which isn't all that uncommon, some or all of the ports on the I/O card may appear to be bad as well. If you use a USB port on another side, it would be routing out of a completely different I/O path, so that's a potential problem.
    If the drive is only seen with a device name such as disk0s16, it's likely either the index files are corrupt beyond Disk Utility's ability to see them. The  only thing that I think would help would be a product named DIsk Warrior, but I can't guarantee that.
    Disk Warrior can be found at:
    http://www.alsoft.com/diskwarrior/
    The company that I linked in the first link above also makes a product named Scannerz that does HD and system testing. The Scannerz/Disk Warrior combination make a good pair because the complement each other....Scannerz does what Disk Warriror can't and Disk Warrior does what Scannerz can't. However, at this point I'm not too sure getting a tool like Scannerz would be of much use because it sounds like the  damage has already been done.
    Let us know what happens.

  • Helix only works with external power

    Hello
    Just received my Helix and I have some issue, one of the biggest issue so far is that it will only power up and stay on with external power, when I dock it it works fine, if I undock it it will shut down, if I plug the power cord to the tablet it will power on but as soon as I remove the power cord it will shut down, I have checked and the batteries are 100% charged, any advice ?
    thanks
    Solved!
    Go to Solution.

    Thanks for the reply, I called Lenovo tech support and they thought it was the mother board, the tech changed it and it did the same he suspected a faulty battery, he replaced that and it works great now, so it was a faulty battery on the tablet it was not getting charged, Lenovo tech support was great, quick and very apologetic, love the laptop so far, thanks for all the help.

  • 17"display with extern power supply won´t work

    Hi there,
    my second display a 17"apple studio display (CRT with VGA) just works every now and then. Can´t locate what´s wrong, I already changed the graphic card, no result. In system profiler both displays are listed mostly, also in the display menue on the topbar, though as soon as I tell to recognize the displays only the main display remains. The 17" display has the extern power supply, but it´s a original apple as well. Thought it might be a bad contact, but can´t find anything. Living here in spain I nearly have no chance to check the display by a dealer. I would be grateful for some help, Michael.
    G5   Mac OS X (10.3.8)  

    Try an SMC reset:
    http://docs.info.apple.com/article.html?artnum=303319

  • No internet with external power on L20

    Can connect to internet when my L20 runs off own power pack, but when battery level goes low and asks for external power, internet connection is lost when my mains power adaptor attatched. Also, internet will not connect if external power supply is used from the outset. Disconnect external power and run on battery pack, internet connection can now take place !! Any thoughts.

    Try checking that the polarity of the dc power coming out of the ac adapter is correct. In fact check that you have any dc voltage coming out of the adapter.
    I don't really understand what you're describing. Are you really saying that ONLY the internet connection is affected. That everything else is working ok on mains power. The power and disk indicator lights are all on; the battery charges up ok; the screen is lit; the fan is running and that these things will continue to work if you then removed the battery? (Except the battery charging of course).

  • Testing keyboard connector with external power key

    My PowerBook recently would not wake from sleep. I was unable to use the usual cmdctrlpwr to reboot it, so I removed the battery. Since then, it has not responded in any way to my pressing the power key. (The battery has all its LEDs and the power adapter turns colors when plugged in.)
    I've had a few keyboard connector problems recently, so I tried reseating the connector to no avail. Additionally, an external USB keyboard's power key had no effect. My question is this: should the PowerBook G4 17" 1.33GHz respond to a power key on an external keyboard? If it should, then I can stop working on the keyboard connector and think about the power system and logic board.
    I can't find any listing of computers on which this behavior is supported; if I missed something, please let me know. Thanks!

    most likely it's not supposed to work with the external power button on the keyboard.
    if you are removing top case, there are "power button" contacts in the lower middle of the logic board which can be used for testing.
    no power issue could be caused by bad keyboard/keyboard cable, since the power button connects thru the keyboard cable.
    any taking aprt of laptops at home is risky though and could cause more damage.

  • Powering down display with external power supply

    I am using a 23" display with an old PowerMac G4 from 1998 with an upgraded video card and external power supply.
    Is there any way to power off the monitor without powering down the computer? Ideally I'd like this to happen automatically based on my system prefs, but apparently the external power supply precludes this.
    As a "workaround", I've created a screen saver that displays a black image. Does this actually save any energy and/or extend the life of my display?
    Thanks,
    - Michael

    Hi Michael,
    Welcome to the discussions.
    You can install an on-off switch on the power lead to the external power supply (actually, it's safer to have a qualified electrician do this, as you are dealing with a mains power supply). I have this system for my ADC 15" Display, and it works fine.
    A black screen saver will not extend the life of your monitor. Screen savers were meant to mitigate the "burn in" effect that happens with CRT displays (and which doesn't happen with LCD displays). If the display is still on, the backlights will still be functioning and they are the finite life component of the LCD display that you need to look after. Also, because the LCD's themselves use so little energy, there will not be much energy saving.
    It's more appropriate to "sleep" the display. You can do this (via Energy saver settings in System Preferences) without having to "sleep" the entire computer. This will turn off the backlights and significantly extend the life of the display.
    (I'm presuming you are using OS X - you haven't supplied any details regarding your system. :))
    Cheers!
    Karl

  • NI USB 8451 with external power source

    Hello everyone !
    I try to figure for 2 days now why my USB 8451 gave me an error 301740 : SDA or SCL line or both are in a low state or there are no pull-up resistor.
    I try to change a multiplexer channel in order to obtain a temperature mesurement from a sensor. I checked my SDA and SCL lines, thye're both in high state and i have 2 pull-up resistors with a value of 10K.
    The only change with my older circuit is that  i use an external power supply for my electronic chip and a MUX PCA9543(texas instruments) to select the sensor of which i need the data .
    Does anyone have encountered similar issues ?
    Solved!
    Go to Solution.

    Ok guys,
    apparently, the ground of my usb 8451 wasn't connected to the ground of my power supply, it is not working yet but my components are responding !

  • Automated disabling screen blackout with external power

    Does anyone have a solution to automatically defeat the screen blackout, other than turning it off in the screen options, so that the screen will stay on while external power is connected and revert to the set screen saver settings when on battery power.  This would be helpful when using Navigation or other applications that require screen on mode but retain the battery saving function of teh screen blanking.  I have an 8830 with Sprint service.
    Thanks to anyone with a suggestion

    You need to install BBLight on your BlackBerry.

  • Shut off with external power loss

    My macbook shuts off when the external power source is disconnected. It will not turn on when external power is not connected. Battery is at 100%, This happens 95% of the time. The other 5% every thing is normal. What is wrong? What dan be done

    - Press the control key, the command key, and the power button simultaneously and hold for three seconds to try to restart the computer.
    - Reset the PRAM. After pressing the power button, hold down these keys simultaneously: Command-Option-P-R, until you hear the startup chime at least one additional time after the initial startup chime.
    - Reset the SMC for the MacBook And MacBook Pro by removing the AC power, removing the battery and then holding down the power button for five seconds.

  • Can anyone help me with External power for the 2900XL

    I hope someone can help me,
    I've got the cisco 2900 XL catalyst, and now my power supply is broken.
    I know its possible to use my own adapter of an normal desktop pc, but i wanna know what the color code is that i must use.
    The current power supply to the mainboard of the cisco is from left to right:
    Orange | black | black | red | red | none
    I also try to find some on the internet but can't find a thing. Can anyone help me or refer me to an site ?
    Thnx.

    check out the following link on power connectors for Catalyst 2900 XL :
    http://www.cisco.com/en/US/products/hw/switches/ps605/products_installation_guide_chapter09186a00800d9cfe.html#1068450

  • How to use external timebase for Two Edge Separation measurement with PCIe 6351

    Hi
    I am working with PCIe 6351 x series DAQ card.
    counter measurements.
    Here i need to measure the time/no edges between two edges. Falling to Raising of two signals.
    I got the measurement with internal time base.
    here i need to synchronize the measurements with external clock from the external setup.
    so i need to use that external clock,timebase for the counters.
    Any solution please..
    Regards,
    Hari

    First, the VI you mention is NOT for STC timer/counters. Therefore, it won't work.
    If you want to get the time interval between two edges, you want to use the Functions -> Data Acquisition -> Counter -> Count Events or Time VI. This will do the function you are looking for.
    Mark

  • Nano won't play using the battery, but ok on external power.  Got washed in the washing machine.

    I washed my nano with my jeans in the washing machine.  It still works when I use external power, but not on the battery.  I've charaged it, but it doesn't hold the charge.   Sugggestions?

    The battery is dead, permanantly pretty much.
    I had this happen to an old nano, 2nd gen or 3rd i forgot which it was.
    Anyway i went in a lake with it, after that it would no longer work on the battery, but would with external power.
    I spent a good while looking for a solution but couldn't find a fix or any suggestions other than replacing the ipod battery, or the ipod itself.
    I did keep it though and just kept it on a ipod player speaker device though. Maybe now theres a trick to fix it or something but i highly doubt it.

  • If I back up iMovie projects to an external drive does it take the media with it? I want to free up space and remove pictures that were in iPhoto...that were used as media by iMovie when project was under way. In short I want archive iMovie stuff

    If I back up iMovie projects to an external drive does imovie  take the media with it? I want to free up space and remove pictures that were in iPhoto...that were used as media by iMovie when project was under way. In short I want archive iMovie stuff. If I pull pics out of iPhoto, and later want to drag an archived projet bac into iMovie and the pics are no longer in iPhoto, will I be able to keep working in the project in iMovie?

    Very likely not, as the iPhoto's can be used for something else.
    More like it took a copy, or it's referencing that spot on the drive in the editable files and most likely made a copy to create a new permanent export file.
    Sample one picture and a iMovie file and see what happens.

Maybe you are looking for