Nike Amp: stops connecting half way through workout

I've been using the Nike Amp with my ipod for the past two months. It's a great piece of kit, and I've come to depend on it to change music, pause a workout when I need to wait for traffic etc. Now it loses it's connection to the ipod mid workout which is rather frustrating. Does anyone else have experience of this problem and any advice as to how I may resolve it? Thanks

This happens to me in a roundabout way. I suspect the watch is just not a very good transmitter. I've had 3 watches replaced now and they all do the same thing.

Similar Messages

My 80 gig ipod color stops updating half way through

My ipod 80 gig color stops updating half way through the synch process. I have tried to restore it and it still fails and gives me an error message saying it cannot read or wrtie to the ipod after it is half way loaded after trying to load 5000+ songs only it gets to about 2,250 and stops.

It could be an indication or a damaged or dying hard drive. I would recommend doing a disk diagnostic on the iPod's HD using the instructions given by turingtest2 in this older thread. He also covers what the resulting numbers indicate.
https://discussions.apple.com/thread/3784647?start=0&tstart=0
If necessary, post the resultings numbers and we can verify what the next steps to take.
B-rock

IPOD CLASSIC STOPS SYNCING HALF WAY THROUGH

my ipod classing stops syncing half way through and says could not be synced can anyone help me please?

It could be an indication or a damaged or dying hard drive. I would recommend doing a disk diagnostic on the iPod's HD using the instructions given by turingtest2 in this older thread. He also covers what the resulting numbers indicate.
https://discussions.apple.com/thread/3784647?start=0&tstart=0
If necessary, post the resultings numbers and we can verify what the next steps to take.
B-rock

IT tunes music - some, a lot, of somgs stop playing half way through. the files are all ok and complete? ive tried downloading / updating but no joy?

IT tunes music - some, a lot, of songs stop playing half way through. the files are all ok and complete? ive tried re - downloading / updating but no joy? can anyone help its most annoying

Yes, in theory re-converting would lessen the quality further. However, I have heard people claim (unsubstantiated) that if you are encoding with the same encoder at the same bit rate, then since it will use the same algorthymn, it won't really change the file. I have absolutely no idea if that is true or not.
But... I figure some slight loss in quality re-encoding is still better quality than a song that only plays half way and then stops, right? I suppose you could always tag those files in the comment section with something like "Re-Encoded" and then later if you gain access to your old CDs, you can then make a Smart Playlist to gather those songs and then re-rip them again from your CDs.
Cheers,
Patrick

My Mad Men shows stop downloading half way through. Why is that happening, and how do I fix it?

I bought mad men and the shows stop downloading half way through. Help!

Do you get an error message when you try to download the items? If so, what does it say? (Include error message numbers if you're getting any, please.)

I recieved a notice that there was an update for Elements 13 but when I try to install it it stop's half way through then I get the error message that "updates could not be applied" I have tried several times and it continues to give me the error. What is

I get a message that an update is available and when I install it the update stops half way through and I get the error code: U44M1I210 for Camera Raw and Elements 13.1 updates. I get the message "UPDATES COULD NOT BE APPLIED" Can someone help with this? Thank you. David

drmeyers381
Thanks for the follow up.
Is your Premiere Elements 13 on Mac computer?
I have not seen much in the way of alternatives coming from Adobe on the Premiere Elements 13.1 failed updates.
But there seems to be several discussions on U44M11210 in the CC products...one
Update failure. (U44M1I210) | Adobe Community
You could try the uninstall, free ccleaner, reinstall with antivirus and firewall(s) and then try for the Help Menu/Update for 13.1..
If Mac, https://www.piriform.com/mac/ccleaner
If Windows, CCleaner - PC Optimization and Cleaning - Free Download
The CC people seem to have the advantage of an online download of their update as well as the one via the Help Menu/Update.
Premiere Elements does not have that perk - update only via Help Menu/Update.
Please review and consider and please let us know of your progress as your schedule permits.
Thank you.
ATR

Why do songs stop playing half way through?

My husband downloaded a new playlist to his iphone, but many of the songs end half way through and then go on to the next song. How can we fix this?

Hi ktrib76,
In my experience, the songs that are skipping may not have transferred over to your husband's iPhone correctly. I would advise you to uncheck the "Sync Music" checkbox, and apply the changes (so there is ultimately no music syncing to the iPhone).
Once you have done that, recheck the "Sync Music" checkbox, and apply the changes once more. This will instruct iTunes to completely remove all music from the iPhone, and then copy the files once more. If you have a large amount of music, this initial sync may take a while.
If the above does not resolve your issue, see the following articles:
iPhone and iPod touch: Songs or other audio content are skipped during playback
http://support.apple.com/kb/TS3159
Troubleshooting songs that skip
http://support.apple.com/kb/TS3217
Cheers!,
Matt M.

My nano just switches off and stops playing half way through a track

Tried resetting several times ... still stops after approc a minute
I switch it back on and press play and it continues right were it went on pause.
Attempted to check if the MUSIC SETTINGS had some timeout ... but cant succeed.
Any advice?

Your nano is pausing playback when the screen goes dark (Either when it goes dark on its own or when you click the sleep/wake button). The reason for this is that it is not detecting your headset. You may be able to hear music, but the headset jack is not inserted enough for the nano to detect that it is there (or something is blocking the connection). Here are your three options:
Insert the headset jack harder. Most folks find that this solves their problem. If you can see ANY of the silver of the plug when it is inserted, it is NOT fully inserted. You should feel and hear a click" when it is fully inserted.
Clean out the crud in the headset port. If you have tried #1 and it just won't insert all the way, it is likely that you have crud in your headset jack. Shine a light in there. The entire inside of the jack is white, so if it looks dark down at the bottom, there is probably crud down there. You can try blowing it out or using canned air. Just understand that shoving anything else in there to clean it out will be taking your warranty into your own hands! However, I have cleaned mine out using whatever was handy and small enough to fit in there and so far so good. Your results may vary!
Take it to the Apple store. If you have really tried with 1 and 2 and it is still happening, then there might just be something up with your headset port or your headset jack. If it is the headset jack, you can look closely at that and be pretty sure if that is the problem. Try another headset to make sure. If you have worked all the way through to this point and it is still happening, it is time to take it to the Apple store.
i

Stop rebooting half way through

My phone stopped rebooting over half way the rebooting process. The line is just sittng there

Please try to boot your handheld in safe mode, using procedure given in below URL
http://btsc.webapps.blackberry.com/btsc/viewdocument.do?externalId=KB17877&sliceId=2&cmd=displayKC&d...

Media Encoder CS4 stops encoding half way through

I am going a little bit insane.
Running PP and Media Encoder CS4 on Windows 7 and attempting to export a 5 minute film on preset 'Download NTSC Source' (but this happens no matter what settings I use): Media Encoder runs for approximately 5-6 minutes, loads the sequence, begins to encode and then stops.
It doesn't spit out an error message, it finishes the file (a 6MB .wmv file (on these settings) that plays a blip of white and then ends) but never gets further than four minutes through what should be a 35 minute encode process.
I've trashed the prefs, I've run all the updates, I'm using XP Compatibility mode ... I literally cannot figure out why the process should just ... stop.
Help??

Welcome to the forum!
Do you have any titles, graphics or MOV files near the beginning of your sequence? I think there was a bug in CS4 that would trash the encode if they were there. It was eventually solved -- either through an update or in CS5. Make sure your copy of CS4 is fully updated.
Jeff

Was watching a video I downloaded earlier today, and it worked fine. Tried watching it now and it stops about half way through. Solutions to this issue?

This happened just today with the only two videos I downloaded from iTunes. They seemed to stop working after I synced my itouch, but I don't know how that would have caused the problem... Both videos will play about 2 minutes on the itouch, then stop.

In case you do not know, to redownload videos you have to contact iTunes.
How to report an issue with Your iTunes Store purchase

I bought an album but 3 of the songs stop playing half way through, it's just silence. Can I get a refund and if so, how?

Recently, I bought the Adam Barnes album and I put it on my iPod. When I started listening to it and it was great. But when it got to track 4, it played the first minute and then it was just silence for the rest of the 3 and a half minutes song. It did this again for tracks 5 and 6 too, but the other tracks are fine. I checked my iTunes and it doesn't work on there too. Has this happened to anyone else? Can I get a refund? If so, how can I get one?

Welcome to the Apple Community.
Try deleting the problematic file (electing to remove original file if/when prompted) and then re-downloading the file from the iTunes store.
You can re-download content purchased from the iTunes store (availability varies depending on location) using the purchased option from the Quick Links section in the top right corner of the iTunes homepage in your iTunes application on your computer.
You can re-download content purchased from the iTunes store (availability varies depending on location) using the purchased option at the bottom of the screen of the iTunes app (or video app) on your iOS device.
If the problem re-occurs, select the content which is causing a problem and use the 'Report a problem' button in Your Purchase History using your computer.

Creative cloud installer stopes installing half way through. No error. The window just disappears.

No issues downloading the DMG. but I cant actually run the installer all the way. Im running 10.10 and there dousnt seem to be any trace of cc on my Mac?
Help please.

Spdj86 please utilize the steps listed in Error "Failed to Install" Creative Cloud Desktop application - http://helpx.adobe.com/creative-cloud/kb/failed-install-creative-cloud-desktop.html to reinstall the Creative Cloud Desktop application.

Duces ex. stopped downloading half way through and now it wont restart.

i was downloading this game. i walked away for a while and when i came back it ahd stopped downloading and it was not installed. in the app store under purchases, i clicked the install button. it tried to restart the download, but afer a minuet or so i get a popu[ telling me that the app failed to download. whats the deal how do i get this download to finish?

I have the same issue just keeps stopping....?

Rich forms stop loading half way through

Hi, I have already posted this in the getting started forum
but it didn't get any response, thought I might try here too to see
if anyone here can help.
I am having a few problems with my testing server (CF 7.02
developer version) that I am hoping someone can shed some light on
for me. I am having two issues which may be related, one
(Administrator) is not really a problem for me, but as they may be
related I thought I'd mention both. I'm sure when I get them sorted
out the solution will be obvious, but right now I just seem to have
a mental block on where I should be looking to resolve it.
The machine is running Apache on Windows Xp, the webroot is
localhost/public/
Basic cf pages are running fine (all images etc appear as
expected), but when I go to view administrator using the link under
programs (Start button) it looks for it at
localhost/CFIDE/administrator/index.cfm and gives a "file not
found" error. If I add /public/ to the address administrator opens
but all images are broken (the images are being looked for at
localhost/CFIDE/administrator instead of
localhost/public/CFIDE/administrator). As I said, this isn't really
a big deal, but may be a symptom of the problem that is causing my
other issue.
I am starting to play with Rich forms, and while the files I
have created work on the production server at our host, I had not
been able to get them working on my testing server (just gave me a
blank space instead of the form). I managed to improve the
situation this morning by changing CFAdministrators 'Default CFFORM
ScriptSrc Directory' setting from /CFIDE/scripts/ to
/public/CFIDE/scripts/. Unfortunately, that wasn't the whole
problem though as now my rich forms start to load but never seem to
complete that process. The timer icon remains on the cursor
indefinately and some parts of the form (stuff within cfitem tags,
as well as any data in datagrids coming from queries) does not
appear. Actual form fields/buttons etc do appear though. The fact
that the timer stays there and the progress of loading the flash
form seems to stop suggests to me that it is looking for something
that it can't find, and therefore may be related to the path
problems I seem to have.
So it seems when I installed CF I didn't tell it where to
look for web files correctly. As I said, I'm sure I should know
this, but can't for the life of me think of where I should be able
to tell cf where the web root is. I am hoping when I do all of my
rich form problems will dissapear (as well as allowing me to see
the CF Adminstrator pages in all their glory with images instead of
boxes with broken icons).
Any help or advice would be appreciated.
Peter.

Please see the reply in your
Getting
Started thread

Nike Amp: stops connecting half way through workout

Similar Messages

Maybe you are looking for