NIPBCFK.sys

I am having my computer post a Unknown Device Error in the System Devices . When you look at the device it states that it is a National Instruments device with the following files:
NIPCFK.sys Version 1.1.1.f0
NIPXIBAF.sys Version 2.5.4f1
NIPXIBRC.sys Version 2.5.4f0
I am unable to update the drivers or clear this error from the list.
Can anyone explain to me what this error is and how I can correct it?
Thanks

Hi Bill,
Would it be possible for you to attach a picture of your device manager, or just the portion that lists the errors, along with a MAX Report so that I can compare the NI software that you have installed to the error that you are receiving? Have you ever used this computer to communicate with a PXI chassis before?
Thank you for your help.
Regards,
Marcus
Marcus M.
PXI Product Support Engineer
National Instruments

Similar Messages

BSOD controlling Nanotec servo (Labview+visa+Daqmx)

I'm using a set-up where I control a servo with Labview. I run the VI, set some speeds to the servo, and within minutes, Windows gets a BSOD. I would like to know the cause of the problem and a fix please.
What am I using?
- Windows 8.1 (and windows XP before)
- Labview Student Ed 2014
- NI Visa
- NI Daq mx
- USB to RS-485/422/232 Converter
- Nanotec servo
- Nanotec Labview example: http://en.nanotec.com/support/application-notes/labview-example/
What happens?
I open the VI, set the com port. Run the VI and set some motor speeds. Within minutes windows 8.1 gives a Blue Screen, with the error MULTIPLE_IRP_COMPLETE_REQUESTS. In Windows XP, this gave the error IRQL_NOT_LESS_OR_EQUAL. After rebooting, windows 8.1 shows Automatic Repair. 'Automatic repair couldn't repair your PC', and refers to C:\WINDOWS\system32\Logfiles\Srt\SrtTrail.txt.
This is 'Startup Repair diagnosis and repair log'. This gives some actions that take 0ms, untill finally:
Boot critical file c:\windows\system32\drivers\nipbcfk.sys is corrupt.
Repair action: File repair
Result: Failed. Error code = 0x2
Time taken = 8546 ms
Opening that file in notepad shows this: http://pastebin.com/dwp2X5er
Can anyone spot why Windows goes into a BSOD, and how this can be prevented?

It sounds like the installation of some NI drivers failed on your system. Can you please re-install those? I recommend to uninstall the current installed ones first.
Also, please try to install the latest driver versions. If you are using old drivers (e.g. from an out-dated driver DVD), it is possible that you have drivers installed which were never tested with Windows 8.1.
Norbert
CEO: What exactly is stopping us from doing this?
Expert: Geometry
Marketing Manager: Just ignore it.

Instead of using the make file can you build nirlpk.sys using MS WDK 8.0 on VS2012?

After downloading the NI nimhddk_windowsWDM-2 and -1
Instead of using the make file I built nirlpk.sys using MS WDK 8.0 on VS2012
I copied the source files out of the dir /nirlpk to the MS template for WDM drivers
It built after turning warnings as errors off.
After uninstalling the NI_DMX driver I tried to install the RLP driver that consisted of nirlp.inf and nirlpk.sys
I got this message:
Windows found driver software for your device but encounted and error while attempting to install it.
PCI-6602 RLP WDM
Driver is not intended for this platform
Is the nirlp.inf file correct for loading on Windows 7 64 bit?
Any ideas?

I have now altered the example along lines
suggested by ghaneman*, who pointed out that
a trusted application did not need to use the
FileOpenService/FileContents just to get an
InputStream.
* Mentioned on 'File associations / sandboxed app.'
http://forum.java.sun.com/thread.jspa?threadID=785224
The altered code is..
/** Load a file into the editing area.
@param path A string representing the path to the desired file. */
public void loadFile(String path) {
    // first try as if this were a trusted application..
    if (!path.equals(".")) {
        try {
            FileInputStream inputStream = new
                FileInputStream(path);
            loadFile(inputStream);
        } catch (Exception e) {
            // we do not have trust, use the FileOpenService
            loadFileByFileService(path);
    } else {
        // we only have a directory, use the FileOpenService
        loadFileByFileService(path);
public void loadFileByFileService(String path) {
    try {
        if (fileOpenService==null) {
            fileOpenService = (FileOpenService)ServiceManager.
                lookup("javax.jnlp.FileOpenService");
        fileContents = fileOpenService.openFileDialog(path, xtns);
        // the user may have cancelled the action..
        if (fileContents!=null) {
            loadFile( fileContents.getInputStream() );
    } catch(UnavailableServiceException use) {
        use.printStackTrace();
    } catch(IOException ioe) {
        ioe.printStackTrace();
}If the user launches the trusted version, and
selects 'always trust' for the (self signed)
certificate, the end user can thereafter double
click a file and see it appear in the application's
editing area with no further user interaction.

"Couldn't load library 'C:\SAP\NSP\SYS\exe\run\dbsdbslib.dll'"

Hi!
As you can see from here :
http://www.fabiocavallo.it/sap/maxdb.jpg
MaxDB seems to work fine, but after starting application server i have got an error :
SAPGUI Logon Error Message:
http://www.fabiocavallo.it/sap/sapguilog.jpg
...here comes dev_w0 :
trc file: "dev_w0", trc level: 1, release: "700"
ACTIVE TRACE LEVEL 1
ACTIVE TRACE COMPONENTS all, MJ
B
B Thu May 22 19:58:50 2008
B create_con (con_name=R/3)
B Loading DB library 'C:\SAP\NSP\SYS\exe\run\dbsdbslib.dll' ...
M *** ERROR => DlLoadLib: LoadLibrary(C:\SAP\NSP\SYS\exe\run\dbsdbslib.dll) Error 126 http://dlnt.c 237
M Error 126 = "Impossibile trovare il modulo specificato."
B *** ERROR => Couldn't load library 'C:\SAP\NSP\SYS\exe\run\dbsdbslib.dll'
http://dbcon.c 4726
M sysno 00
M sid NSP
M systemid 560 (PC with Windows NT)
M relno 7000
M patchlevel 0
M patchno 95
M intno 20050900
M make: multithreaded, ASCII, optimized
M pid 3376
M
M kernel runs with dp version 224(ext=109) (@(#) DPLIB-INT-VERSION-224)
M length of sys_adm_ext is 360 bytes
M ***LOG Q0Q=> tskh_init, WPStart (Workproc 0 3376) http://dpxxdisp.c 1301
I MtxInit: 30000 0 0
M DpSysAdmExtCreate: ABAP is active
M DpSysAdmExtCreate: VMC (JAVA VM in WP) is not active
M
M Thu May 22 19:58:51 2008
M DpShMCreate: sizeof(wp_adm) 6328 (904)
M DpShMCreate: sizeof(tm_adm) 3605136 (17936)
M DpShMCreate: sizeof(wp_ca_adm) 1200 (60)
M DpShMCreate: sizeof(appc_ca_adm) 1200 (60)
M DpCommTableSize: max/headSize/ftSize/tableSize=500/8/528040/528048
M DpShMCreate: sizeof(comm_adm) 528048 (1048)
M DpSlockTableSize: max/headSize/ftSize/fiSize/tableSize=0/0/0/0/0
M DpShMCreate: sizeof(slock_adm) 0 (96)
M DpFileTableSize: max/headSize/ftSize/tableSize=0/0/0/0
M DpShMCreate: sizeof(file_adm) 0 (72)
M DpShMCreate: sizeof(vmc_adm) 0 (1280)
M DpShMCreate: sizeof(wall_adm) (22440/34344/56/100)
M DpShMCreate: sizeof(gw_adm) 48
M DpShMCreate: SHM_DP_ADM_KEY (addr: 06420040, size: 4205552)
M DpShMCreate: allocated sys_adm at 06420040
M DpShMCreate: allocated wp_adm at 06421A28
M DpShMCreate: allocated tm_adm_list at 064232E0
M DpShMCreate: allocated tm_adm at 06423310
M DpShMCreate: allocated wp_ca_adm at 067935A0
M DpShMCreate: allocated appc_ca_adm at 06793A50
M DpShMCreate: allocated comm_adm at 06793F00
M DpShMCreate: system runs without slock table
M DpShMCreate: system runs without file table
M DpShMCreate: allocated vmc_adm_list at 06814DB0
M DpShMCreate: allocated gw_adm at 06814DF0
M DpShMCreate: system runs without vmc_adm
M DpShMCreate: allocated ca_info at 06814E20
M DpShMCreate: allocated wall_adm at 06814E28
X EmInit: MmSetImplementation( 2 ).
X MM global diagnostic options set: 0
X <ES> client 0 initializing ....
X Using implementation view
M <EsNT> Memory Reset disabled as NT default
X ES initialized.
M ThInit: running on host PCFABIO
M
M Thu May 22 19:58:52 2008
M calling db_connect ...
B create_con (con_name=R/3)
B Loading DB library 'C:\SAP\NSP\SYS\exe\run\dbsdbslib.dll' ...
M *** ERROR => DlLoadLib: LoadLibrary(C:\SAP\NSP\SYS\exe\run\dbsdbslib.dll) Error 126 http://dlnt.c 237
M Error 126 = "Impossibile trovare il modulo specificato."
B *** ERROR => Couldn't load library 'C:\SAP\NSP\SYS\exe\run\dbsdbslib.dll'
http://dbcon.c 4726
M ***LOG R19=> ThInit, db_connect ( DB-Connect 008192) http://thxxhead.c 1426
M in_ThErrHandle: 1
M *** ERROR => ThInit: db_connect (step 1, th_errno 13, action 3, level 1) http://thxxhead.c 10240
M
M Info for wp 0
M
M stat = WP_RUN
M waiting_for = NO_WAITING
M reqtype = DP_RQ_DIAWP
M act_reqtype = NO_REQTYPE
M rq_info = 0
M tid = -1
M mode = 255
M len = -1
M rq_id = 65535
M rq_source =
M last_tid = 0
M last_mode = 0
M semaphore = 0
M act_cs_count = 0
M csTrack = 0
M csTrackRwExcl = 0
M csTrackRwShrd = 0
M control_flag = 0
M int_checked_resource(RFC) = 0
M ext_checked_resource(RFC) = 0
M int_checked_resource(HTTP) = 0
M ext_checked_resource(HTTP) = 0
M report = > <
M action = 0
M tab_name = > <
M vm = no VM
M
M *****************************************************************************
M *
M * LOCATION SAP-Server PCFABIO_NSP_00 on host PCFABIO (wp 0)
M * ERROR ThInit: db_connect
M *
M * TIME Thu May 22 19:58:52 2008
M * RELEASE 700
M * COMPONENT Taskhandler
M * VERSION 1
M * RC 13
M * MODULE thxxhead.c
M * LINE 10439
M * COUNTER 1
M *
M *****************************************************************************
M
M PfStatDisconnect: disconnect statistics
M Entering TH_CALLHOOKS
M ThCallHooks: call hook >ThrSaveSPAFields< for event BEFORE_DUMP
M *** ERROR => ThrSaveSPAFields: no valid thr_wpadm http://thxxrun1.c 720
M *** ERROR => ThCallHooks: event handler ThrSaveSPAFields for event BEFORE_DUMP failed http://thxxtool3.c 260
M Entering ThSetStatError
M ThIErrHandle: do not call ThrCoreInfo (no_core_info=0, in_dynp_env=0)
M Entering ThReadDetachMode
M call ThrShutDown (1)...
M ***LOG Q02=> wp_halt, WPStop (Workproc 0 3376) http://dpnttool.c 327
File dbsdbslib.dll' is 'there' (in 'C:\SAP\NSP\SYS\exe\run\), maybe i have to set environment variable in windows for SAP.
Could you help me, please ?
I don't know how to set these variables.......
Many thanks.
Regards.
Fabio

Hello Fabio,
-> You wrote:
"File dbsdbslib.dll' is 'there' (in 'C:\SAP\NSP\SYS\exe\run\)"
=> Please check the version of this file.
< Go to file properties ->Version && update with 'file version', Platform,
   Product Name, Product Version information >
-> What version of the SAP system did you install?
     "I suppose that i can download this patch from Sap MaketPlace, but i can't register there, because i have no
      Customer or   Installation Number! (i can't Logon in SAP....) "
     From were did you get the SAP software installation or CD?
-> Could you upgrade the database client software on the application server to the version 7.7.04.08 or higher.
    You pointed "As you can see from here : http://www.fabiocavallo.it/sap/maxdb.jpg u2026 "
   => If the database and application were running on the same server, you installed the database
Software version 7.6.02.17. Please run 'sdbregview -l' to review the list of all installed packages
on the server.
-> "MaxDB seems to work fine, but after starting application server i have got an error"
     Was the system working fine before? What was changed?
     Or you was not able to start the application server after installation. ?
Thank you and best regards, Natalia Khlopina

Upgrade oracle 9.2.0.8.0 to 10.2.03 ORA-06512: at "SYS.VERSION_SCRIPT", lin

Upgrade oracle 9.2.0.8.0 to 10.2.03. while runing catupgrd.sql script. i am geting error.
SELECT version_script AS file_name FROM DUAL
ERROR at line 1:
ORA-20000: Upgrade not supported from version
ORA-06512: at "SYS.VERSION_SCRIPT", line 52
Please help me.
AT

Strange. Metalink doc 316889.1 says you should be able to upgrade following versions directly to 10.2.0.3.0
8.1.7.4 -> 10.2.X.X.X
9.0.1.4 or 9.0.1.5 -> 10.2.X.X.X
9.2.0.4 or higher -> 10.2.X.X.X
10.1.0.2 or higher -> 10.2.X.X.X
Not too sure but may be you need to contact Oracle support.

COMPUTE INDEX vs. SYS.DBMS_STATS.GATHER_INDEX_STATS

Hi,
I've got an Oracle 9 database.
I am creating an index. I had created this index using the following syntax:
CREATE INDEX index1. . . . . . COMPUTE STATISTICS;
One of my colleagues tells me that I should scrap 'COMPUTE STATISTICS' and instead make this a two step process:
(1) CREATE INDEX index1. . . . .
(2) SYS.DBMS_STATS.GATHER_INDEX_STATS
OwnName => 'schema'
,IndName => 'index_name'
,Estimate_Percent => 10
,Degree => 4
,No_Invalidate => FALSE);
Is there any advantage to using SYS.DBMS_STATS.GATHER_INDEX_STATS instead of 'COMPUTE STATISTICS'?
Thanks,
Tom

9i references<br>
In particular...<br>
Deprecated at 10<br>

How to protect the SYS ID?

Hi All,
I have an application that allows a central application administrator - this ID in the application matches to an Oracle ID with no objects, but many rights. Since they need to reset regular user passwords this user gets granted the "ALTER USER" role. Doing some experimentation I found that this user has the rights to change the SYS password now! (and any other SYSDBA user). The documentation does confirm this:
*Security administrators are typically the only users that have this system privilege, as it allows a modification of any user security domain.*
Now, my solution is to remove the ALTER USER privilege and leave the password resets to the DBA (i.e. me), but I was wondering if anyone knows of a solution that will still allow a user to change other database user passwords, but exclude the SYS password?
FYI, this is running 11.1.0.7 on Windows 64-bit. Any ideas would be greatly appreciated.
Thanks,
Martin

Normally, you'd use a stored procedure for this.
A highly privileged user (i.e. a DBA account) would own a procedure that resets user passwords. That procedure would do a bit of validation that the password being reset is a regular application user account, not a DBA. And the procedure would probably do a bit of logging so you can track who reset the password. The highly privileged user would then grant the application administrator EXECUTE access on this stored procedure. The application admin would be able to reset normal user passwords by calling the procedure but would not be able to reset the password for privileged users.
Justin

Jobs running under sys user name

Oracle 10.2.0.3 Enterprise
Win2k3
Just upgraded to 10.2.0.3 ee from 10.1.0.4 standard.
The jobs were entered via em and given the proper owner.
em was logged in as sys. All jobs are running as user name sys.
Can the user name be changed to the owner or do I have to drop and rebuild the jobs?
Thanks for any help
Bob

Hi,
For jobs there are two users, the job_owner and the job_creator.
The job_owner is the schema the job is created in. The job runs as the job owner and with the privileges of the job owner.
The job_creator is the user that creates the job (even if he creates it in another schema). When a job runs it sets its logged-in-user to be the job creator, so any actions will be audited as having been done by the job creator.
Neither the job_owner nor the job_creator can be modified after the job has been created.
But you may be able to use the copy_job command or the create_like EM button to save you some trouble.
Hope this helps,
Ravi.

Vista crcdisk.sys error on Tecra A4

When the beta version of Vista came out several people were having installation problems where start-up would stop on first reboot at 'crcdisk'sys'
I've been following the MS forums as well as here but never found a solution.
Has anyone successfully installed Vista Beta on a Tecra A4 yet? If so, what's the secret?
Any help appreciated
Salamat

Thanks for replying and suggesting the link. I have been keeping my eyes on the MS forums since first installing
Beta2 but not yet found the cause or solution in there. Most of the posts go back to June and July shortly after Beta 2 came out and since it went all quiet I assume people resigned themselves to not solving the problem. With the release of 5536 maybe the issue will raise itself there again.
Thanks
Salamat
> Hi,
>
> Maybe found you a answer for your Question with Vista
> in the Vista Forum.
> Please check this.
> http://forums.microsoft.com/TechNet/Search/Search.aspx
> ?words=Installation+from+Vista&localechoice=9&Site ID=1
> 7&searchscope=allforums
>
> By

I keep getting blue screen and error message to remove this file from system. spooldr.sys

HP Officejet 4500 Wireless All-in-One Printer - G510n    w/operating system     Windows XP Professional
I installed the printer in February and the disk did not finalize the setup process. I went online and
down loaded the drivers and software that was offered from the HP website.
The printer works, but as the months have gone along, I keep getting updates for the printer and
the system needs to reboot and it does automatically.
Now I am getting a blue screen with a critical dump error message. HP error reporting keeps sending
the same message back to restore to earlier date before the updates. That worked for awhile. Now
HP Error system says that malware has corrupted and needs to remove system file     spooldr.sys
Is this in your driver software. Spooldr is the system that caches pages of data for printing in chronological
order....
Can I uninstall my software and drivers and change to the plain & simple, print and scan to prevent the
spool driver from loading to my system?

Thank you for your input. But, It is amazing that you can tell me that I was infected with rootkit.
Without information as to how to fix, your information is after the fact and useless.
I used the Safety Scanner provided to me by HP.  A full scan didn't detect any Malware in any files on my system. But the last screen dump provided the information that   spooldr.sys was corrupted and needed
to be removed.
Coming into HP Form, I did read on the HP website that my system Windows XP Professional was not listed
and noted that the software may have not been just what I needed. This was the reason for the question
about uninstalling and reinstalling less of the program. I really don't need my printer to print backward and
that is all I see that it is doing that other printers don't.
Besides, Kudos goes to the person from HP who sent the email, suggesting I used the HP Update software and drives recommended for my computer system. Computer, printer is working, back to normal and hasn't taken a dump since, I uploaded software and drives for Windows XP Professional.

Storport.sys BSOD on Windows Server 2012 R2

I recently purchased a Server that houses 45 4TB drives to use as my backup to disk solution. I installed Windows Server 2012 R2 Standard so that I could take advantage of Microsoft's Storage Spaces. I have configured the Storage Pool
with Dual Parity with 3 hot spares. I have also updated every thing to the most current firmware, drivers and Windows Updates that I could find but I am still getting the BSOD. I am using Symantec Backup Exec 2010 R3 to backup my file server to this server.
It will run for anywhere between 12 to 31 hours transferring 1.5 to 3TB and then my server will Blue Screen and every time it Blue Screens it says it is caused by the storport.sys Driver. I've found articles talking about the storport.sys driver causing nonpaged
pool leaks but that was for Windows Server 2008 R2, I can't find anything for Windows Server 2012 R2. If you need additional information just let me know and I will provide it. Any help you can give would be greatly appreciated.

Hi,
This article provided the limitation of Storage Pool in Windows Server 2012 R2:
https://social.technet.microsoft.com/wiki/contents/articles/11382.storage-spaces-frequently-asked-questions-faq.aspx#What_are_the_recommended_configuration_limits
Yor current situation is still in supported configuration.
Also there is no hotfix for Windows Server 2012 R2 regarding storport.sys yet. Which means your current issue is not a known issue.
For further troubleshooting purpose you may need to collect dump files for analysis. However it will take a long time to do the troubleshooting process on forum. Thus it is recommended to submit a ticket to Microsoft online support for a professional troubleshooting.
To obtain the phone numbers for specific technology request please take a look at the web site listed below:
http://support.microsoft.com/default.aspx?scid=fh;EN-US;PHONENUMBERS
If you have any feedback on our support, please send to [email protected]

Dc5850 cpu fan speeds to top speed sys then shutdown

I have a Hewlett-Packard HP Compaq dc5850 Micro tower PC, now running windows 7 pro 64-bit. That was new in late 2008. Originally it came with vista 32-bit downgrade able to XP pro 32 bit, running on 2G RAM, and 160G C drive with a 2.30 gigahertz AMD Phenom 8600B Triple-Core processor. It also has ATI 3100 integrated graphics as well as integrated NIC at 1G and integrated High def audio. In the first few months I had the system, I upgraded memory by 4G and total Disc space by 500G by adding a D drive; then upgraded to windows 7 pro 64-bit.
Overall, I have had a good experience with the PC but it has had problems while in its 3-year warranty. I did need to replace the C drive and later it original RAM devices. Yes HP did these replacements and swaps, under warranty; that meant I had 6G memory for a long time before the HP 2Gig failed out of warranty, leaving me with 4Gig now. Yes I have always had the Unit on an UPS; I even replaced the old UPS with a more powerful unit in late 2009 or early 2010 when the old UPS showed signs of failure. Now instead of serial based UPS connection it is USB.
Over the last few months I have been getting blue-screen errors of all sorts. Ranging from video related errors, Memory faults, Disc read/write failures and processor flag errors too. After numerous repair disc runs or re-install of windows, the disc read write errors wore corrected by the HP drive sanitation utility disc repair/wipe after failing the extended test. The non video ram was tested by a bootable CD of memtest86 v4 running extended test as well as MS memory Diagnostic. Both run multiple times, both passed multiple times. I was able to find a CD based video diagnostic for ATI and the Video passed repeated stress test as well. Over Labor Day I conducted these test and re-installed windows 64-bit; on the following Monday windows informed me I needed to activate windows, so I verified the correct key and called to do so, successfully.
With that background given here is the question. Recently over the last two or three months, for no apparent reason, mainly on boot the fan races to top speed and the system shuts down to protect itself. I researched this a little and found one cause to be inadequate airflow over the CPU to keep it cool; the recommendation made sense to vacuum with a computer vacuum and be sure airflow is not somehow obstructed. I am now thinking all these problems are related to the CPU temp sensor. Is it on the CPU fan or the motherboard, and can raising the fan speed in BIOS help prevent the problem, particularly if it on the motherboard.
John M Gray II

My pentium 4 3.0c stock Intel fan is 4.44 watts. Isn't the mobo designed for this?
Also, can the sys fan header have the speed sensor activated by a bios fix or is it a hardware issue where it just does not exist? If hardware, seems strange since Corecell shows sys fan.
Regards

T61 with memory leak on XP for driver battc.sys

Hi
I have an issue with XP where the battc.sys module that is part of Windows XP and responsible for the kernel side of monitoring the battery status. This module continually leaks memory until I have no more kernel paged resources left and programs start to fail on my laptop.
I raised a support case for this with Microsoft and after some investigation and upgrading to the latest T61 power drivers that were released a few days ago on the Lenovo site, MS support told me it is a fault of the T61 and that I would need to disable Microsoft APCI support to stop this memory leak from occuring and to take the issue up with Lenovo.
I have used the verifier tool to confirm that it is the Windows XP SP3 battc.sys memory module leaking.
I am running the latest T61 drivers and fully patch with MS drivers on SP3.
As MS have told me it is the fault of the T61 I am posting this issue here.
Thanks
Stephen

It is memory available to the kernelwhich itself does not show under a process in task manager as far as I am aware (unles it is taken account as part of the system process).
The best way to measure the available kernel memory space available is by using sysinternals procexp.
You need to download procexp and also install the windows debugging tools from Microsoft. Then in procexp set the "Options > Configure Symbols : Debughlp.dll path" to the new debughlp.dll installed with your debu tools and set the symbols path to srv*c:\Symbols*http://msdl.microsoft.com/download/symbols
Then you can choose in procexp "View > System Information" and see the used and total paged and non-paged kernel memory space.
poolmon helps monitor all the symbols that are taking up this memory and verifier lets you drill down to the exact module and the changes in memory for a module that is occuring.
Here are two really good links on it
http://blogs.msdn.com/ntdebugging/archive/2006/12/18/Understanding-Pool-Consumption-and-Event-ID_3A0...
http://blogs.msdn.com/ntdebugging/archive/2008/05/08/tracking-down-mmst-paged-pool-usage.aspx
In my poolmon i notice that Mmst and battc are taking alot of memory after my computer has been running for some time. Mmst being high is normal but battc should not continually be growing as it is which is why I raised the case to MS but they want verification it is not a Lenovo issue.

Am unable to get the data from Sys.databases when i use where condition for column owner_sid

Hi all,
Help me here when i try am unable to get a data,Can some one help me with a query to get.
If it cant be done can i know why..
select * from Sys.databases
where owner_sid='0x01'
What am trying is to get a login
names from syslogin
table with respect to Sid.
Select a.name,b.name,a.owner_sid from Sys.databases a
Join Syslogins b
on a.owner_sid = b.sid
where owner_sid like '0x01'
Thanks all in Advance.....

Below are a couple of examples of how to accomplish the task. Note that SID is varbinary so the literal should not be enclosed in quotes.
SELECT
a.name AS DatabaseName
,b.name AS OwnerName
,a.owner_sid AS OwnerSID
FROM sys.databases a
JOIN sys.server_principals b ON
a.owner_sid = b.sid
WHERE owner_sid = 0x01;
SELECT
a.name AS DatabaseName
,SUSER_SNAME(owner_sid) AS OwnerName
,a.owner_sid AS OwnerSID
FROM sys.databases a
WHERE a.owner_sid = 0x01;
Dan Guzman, SQL Server MVP, http://www.dbdelta.com

Postoffice-startup-file not copied from SYS-volume

We migrated a Groupwise 7.02-postoffice from a Netware 6.5-Sp5-server to a
SLES10-SP1-server with the Novell GroupWise Migration Utility.
When we started gwpoa the postoffice-startup-file was not
in /opt/novell/groupwise/agenst/share/
We looked in the migration-logfile and we saw these messages
10/27/07 02:32:23 Configuring agent(s)...
10/27/07 02:32:23 Running remote command:
sh /tmp/groupwise/software/addagent.sh -
b /opt/novell/groupwise/agents/bin/gwpoa -
s /tmp/groupwise/software/p006.poa -h /var/opt/novell/groupwise/mail/p006 -
v 7
/tmp/groupwise/software/addagent.sh: line
135: /tmp/groupwise/software/p006.poa: No such file or directory
mv: cannot stat `/tmp/p006.poa.tmp.16849': No such file or
directory
cp: cannot stat `/tmp/groupwise/software/p006.poa': No such file
or directory
10/27/07 02:32:25 Remote command failed (1)
This is were our sourcefiles were:
Post Office:
Source database path: \\fileserver\VOL1\DATA\GRPWISE\P006\
Destination path: /var/opt/novell/groupwise/mail/p006
Agents:
Post Office Agent:
Path to startup file: \\fileserver\SYS\SYSTEM\p006.poa
As you see, our startup-file was on another volume then the postoffice.
In the migration-log we only saw a mount of the postoffice-volume, so we
think there is a bug in the migration utility. It does not copy the
startup-file if it is on another volume (in this case on the SYS-volume).
Or did we something wrong?
At last we solved our problem by copying (and editing) a startup-file
to /opt/novell/groupwise/agenst/share/
Regards,
Jeroen van der Klaauw

It happens between the full dbcopy and the incremental dbcopy, when the
agent is configured.
Jeroen van der Klaauw
> When the migration agent finishes the migration of the data there are
> the second and third phases that the application runs through - 2) to
> install the agents and 3) configure them. If you bombed out before
> that third phase then I would understand...
>
>
>
> On Mon, 29 Oct 2007 15:55:53 GMT, [email protected] wrote:
>
> >We migrated a Groupwise 7.02-postoffice from a Netware 6.5-Sp5-server
to a
> >SLES10-SP1-server with the Novell GroupWise Migration Utility.
> >When we started gwpoa the postoffice-startup-file was not
> >in /opt/novell/groupwise/agenst/share/
> >We looked in the migration-logfile and we saw these messages
> >
> >10/27/07 02:32:23 Configuring agent(s)...
> >10/27/07 02:32:23 Running remote command:
> >sh /tmp/groupwise/software/addagent.sh -
> >b /opt/novell/groupwise/agents/bin/gwpoa -
> >s /tmp/groupwise/software/p006.poa -
h /var/opt/novell/groupwise/mail/p006 -
> >v 7
> > /tmp/groupwise/software/addagent.sh: line
> >135: /tmp/groupwise/software/p006.poa: No such file or directory
> > mv: cannot stat `/tmp/p006.poa.tmp.16849': No such file or
> >directory
> > cp: cannot stat `/tmp/groupwise/software/p006.poa': No such file
> >or directory
> >10/27/07 02:32:25 Remote command failed (1)
> >
> >This is were our sourcefiles were:
> >
> >Post Office:
> > Source database path: \\fileserver\VOL1\DATA\GRPWISE\P006\
> > Destination path: /var/opt/novell/groupwise/mail/p006
> >
> >Agents:
> > Post Office Agent:
> > Path to startup file: \\fileserver\SYS\SYSTEM\p006.poa
> >
> >As you see, our startup-file was on another volume then the postoffice.
> >In the migration-log we only saw a mount of the postoffice-volume, so
we
> >think there is a bug in the migration utility. It does not copy the
> >startup-file if it is on another volume (in this case on the SYS-
volume).
> >Or did we something wrong?
> >
> >
> >At last we solved our problem by copying (and editing) a startup-file
> >to /opt/novell/groupwise/agenst/share/
> >
> >Regards,
> >
> >Jeroen van der Klaauw
> Tim
> ___________________
> Tim Heywood (SYSOP)
> NDS8
> Scotland
> (God's Country)
> www.nds8.co.uk
> ___________________
>
> In theory, practice and theory are the same
> In Practice, they are different

NIPBCFK.sys

Similar Messages

Maybe you are looking for