NM-16AM module question in my cisco 3660

hi,
I have 3 of these modules.
with 1 module, when I configure a line and I connect to the line I get only a black screen.
when I do the exact same thing with another module, (configure a line on the 2nd module) it works fine.
my question is, how can I know if a module is broken or not functional. can this happen?
any advice on how to find out if a module is broken or if I single modem in the module is dead.
thank you.
also when I use debug modem and I call a modem that works fine I get this
11w6d: Modem 5/14 Mcom: in modem state 'Dialing/Answering'
11w6d: Modem 5/14 Mcom: in modem state 'Incoming ring'
11w6d: Modem 5/14 Mcom: in modem state 'Waiting for Carrier'
but when I don't get this I know in advance that it's not going to work and that I'll get just a black screen.
any advice please?
thank you.

To identify a functional module , we need to look at the front panel LED of 3660 router. If READY 0, 1, 2, 3 is blinking green it indicates,it indicates the functional module is installed in the slot.If this LED is OFF, it indicates the slot is empty or the module is not functional. For more info on 3660 MAR router, refer the following Link.
http://www.cisco.com/en/US/products/hw/routers/ps274/prod_module_configuration_guide09186a00800d9e97.html

Similar Messages

How to Use Cisco 3660 or 3745 router for FAx

I want to use Cisco 3660 Router or 3745 Router for Receiving FAX on email. I have NM-2CE1T1-PRI which supports E1 R2 signalling on 3660 and 3745 both. What are the additional hardware requires? Kindly Help.

Hi,
You could use T.37 Store and forward fax which has the feature called Onramp faxing.
On-ramp faxing, in which a voice gateway that handles incoming calls from a standard fax machine or the PSTN converts a traditional Group 3 fax to an e-mail message with a Tagged Image File Format (TIFF) attachment. The fax e-mail message and attachment are handled by an e-mail server while traversing the packet network and can be stored for later delivery or delivered immediately to a PC or to an off-ramp gateway. Below URL is for detaield config.
http://www.cisco.com/en/US/products/sw/iosswrel/ps1839/products_feature_guide_chapter09186a00800b5dcf.html
You would not require any extra hardware for the same.
Thanks
GS

Calling process failure tone on cisco 3660

We have a 1 Channelized E1/PRI port cisco 3660,but we have a calling problem on closed cell phones.In other words;when we are calling a closed cell phone,we might be take a rollback anounce like "closed phone tone" but we are taking only continuous ring back tone to our tel.How can we solve on our dial peer method configuration.Could you help us.

The following commands will help you debug the problem
debug voice ccapi inout
debug vpm all
debug vtsp all

Order the FAQ module questions

I am trying to order the FAQ module questions in Business Catalyst.
It puts them in alphabetical order by default so I numbered them. But once it gets to 10 it obviously goes out of order.
And the client does not want to put a letter in front. ie A, B, C
Any ideas on how to acheive this?
Thanks in advance.

Try leaving numerical gaps in your weighting scheme so you have future flexibility.
For example, I like to use the weightings of 1000, 900, 800, 700 and so on.
Then I have a LOT of wiggle room to add new information and sort my information the way I like.
Tricia

SQL Questions (New to Cisco)

Hello. I work for Clarian Health in Indianapolis and am trying to learn as much as possible about the SQL databases, both AWDB and HDS so that I can handle the reporting for our Revenue Cycle Customer Service.
I am currently working my way through the Database Schema Handbook for Cisco Unified ICM /Contact Center Enterprise & Hosted. I’m also reviewing the explanation pages that are available for the reports on WebView. During my reviews, I have noticed a few things that confuse me.
My questions are:
1. Why do a majority of the tables on our SQL Server start with “t_”?
2. Why do some of the tables have data on the AWDB server but not on the HDS server, and vice versa? (Examples: t_Agent and t_Agent_Team and t_Agent_Team_Member and t_Person are blank on the HDS database but not blank on the AWDB database; but the t_Agent_Logout is blank on the AWDB database and not blank on the HDS database)
3. When data is moved to the HDS server every 30 minutes, is it also removed from the corresponding AWDB table?
4. In review of the agent26: Agent Consolidated Daily Report syntax info located on the WebView, 1 of the calculations uses the LoggedOnTimeToHalf from the Agent_Half_Hour table while the remaining calculations uses the same field from the Agent_Skill_Group_Half_Hour table. Can you please tell me why this is? Why would all of the percent calculations not use the data from the same table? (The % of time Agent paused and/or put a task on hold uses the Agent_Half_Hour Table. All other % calculations uses the same field from the Agent_Skill_Group_Half_Hour Table.)
5. Also in reviewing the agent26: Agent Consolidated Daily Report syntax info, I noticed that it contains the Skill_Group table, the Agent_Half_Hour table and the Media_Routing_Domain table. Both the Skill Group table and the Agen_Half_Hour table contain links to the Media_Routing_Domain table. Which relationship/join is actually utilized for this report?
6. Why doesn't the LoggedOnTimeToHalf field on both the Agent_Half_Hour table and the Agent_Skill_Group_Half_Hour table have the same value in them?
7. On the agent_26: Agent Consolidated Daily Report syntax explanation page, the Agent State Times: Log on Duration says that it is derived using the Agent_Half_Hour.LoggedOnTimeToHalf field, but when i convert this field to HH:MM:SS, it does not match the actual WebView report. But, when I use the Agent_Skill_Group_Half_Hour.LoggedOnTimeToHalfHour, it does match. Which one is correct?
8. On the agent_26: Agent Consolidated Daily Report, why does the Completed Tasks: Transfer Out contain both the TransferredOutCallsToHalf and the NetTransferredOutCallsToHalf fields? What's the difference between the two? What Transfer out data writes to each field?
Thank you.
Angie Combest
Clarian Health
[email protected]

You need to be careful when looking at the three databases - Logger, AW, HDS - which use the same schema. But many of what appear to be tables in the AW are really views into the t_ tables in the HDS - the data is not there in the AW DB. You are right to look at the schema - but check with SQL Enterprise to understand a bit more.
In essence, the AW DB is for configuration data and real-time data. The HDS is for historical data. You can query the AW DB for (say) Call_Type_Half_Hour data and join with the Call_Type table to resolve the call type ID into its name - but the data is really in the HDS through the view.
The DB design is quite complex and sophisticated - many things are not obvious.
Keep up your research.
Regards,
Geoff

Training and Event module questions.

Hi .
I have some questions regarding Training and Event Management module.
1. IS there a way to configure a custom attendee type for this module ?
2. If no is there a way to rename a existing attendee type. I have a requirement to create a group of attendees type of External Person. I know i can use Company attendee type for grouping external person. But i need to change this Company to Group for displaying purposes. I know i can change the Company via T7778O table but won't it lead to bad consequences ?
3. Is there a way to hide tabstrips on PVOO screen ? i have a requirement to keep only Company tabstrip others are not relevant for my scenario.
That's all for now.
Thanks in advance.
Edited by: kernel.panic on Dec 22, 2010 8:47 AM

Hi,
thanks this one is ok, the one which I can not find is the info message for when the maximum capacity of the attendee list is reached:
'Optimum capacity reached, only essential or wait list bookings possible' This one I want to change into a warning message.
br,
Ovidiu
And I have a new question as well
In the Attendee List layout is it possible to add columns which are not in the column set from customizing e.g. Personnel subarea,
Employee subgroup, Employee group etc?
Thanks
br,
Ovidiu
Edited by: Ovidiu Moldovan on Apr 20, 2010 3:51 PM

Module Question.

Hi all,
My scenario is File->XI->R3
Can I validate file information in a Sender Adapter Custom Module and if the validation fails then cancel the input so Integration Engine never gets the corresponding message? My question is how to cancel the procesing of the message in the adapter module?
Thanks in advance,
Diego.

Chandu,
my problem is that I want to validate data of an input file, so if the file doesn't contain certain fields, then it doesn't go to the XI Engine. (It's discarded before that.)
So i thought to build a module for the sender adapter that do this validation, but I don't know how to discard the message at modules chain.
I hope you could understand my english.
Regards,
Diego.

FC-2GB module part number for cisco 4503 switch

Dear Sir,
We hv a SAN switch MDS-9216 with FC-2GB ports.
We want to connect the SAN switch to our newly installed cisco 4503 switch which modules is required in the cisco 4503 switch to connect the SAN switch FC-2GB ports.
Regards
Deepak

Deepak,
Can you explain why you want to do this?
The Catalyst 4503 is an ethernet switch and does not support FC-2G interfaces. If you want to enable IP access to your storage, you would need an IP storage services module in your MDS 9216. This would then provide GE interfaces which you could connect to your Catalyst 4503. You could then provide IP-based hosts access to FC-connected storage using iSCSI for instance.
Regards
Rob.

5B32 module question

This is more of an equipment question, but I figure that thisis as good a
place as any to ask.
I've got about six 5B32 modules, and I need three. The problem is that
four of the resistors that go with them are bad. I had as bad board,
which I think might have screwed up the resistors. The resistors that
Ihave that are good are reading about 20 Ohms of resistance, and the bad
ones are 6 Ohms, 80 Ohms, 1.5 megaOhms, and 2.2 megaOhms.
I have tried to buy some resistors from National Instruments and Analog
Devices, but they don't know what they are (the part number doesn't come
up at all). I hate to keep buying entire 5B32 modules when I only need
the resistor. So, can I just go buy a 20 Ohm resistor at Radio Shack, and
plug it i
n, or is this thing that comes with it something special?
Thanks in advance,
Harry
"Little Joe for the Big Heisman, '99"

Absolutely - go down to Radio Shack and purchase some - The max current
sould be 20 ma (since the 5B32 is a 4 - 20 ma current input module) so P =
I^2 R , P = (.02)^2 * 20 = .008 Watts therefore a 1/4 or 1/2 watt resistor
should be more than adequate.
A 1/2 watt resistor has leads that would probably plug into the 5B01
backplane nicely.
Good Luck
Harry King wrote in message <7q65an$[email protected]>...
>This is more of an equipment question, but I figure that thisis as good a
>place as any to ask.
>
>I've got about six 5B32 modules, and I need three. The problem is that
So, can I just go buy a 20 Ohm resistor at Radio Shack, and
>plug it in, or is this thing that comes with it something special?
>
>Thanks in advance,
>Harry
>
>--
>"Little Joe for the Big Heis
man, '99"

Quick Module Question

I have a link bar component that is linked to a ViewStack
component, which has four stacks. I want to use modules in the last
three stacks and my question is: Will the modules load when the
user clicks on that particular stack, or will all of them be loaded
even if the currentView property is set to 0?

I think that that has to do with the "creation policy" and
can be set either way.

STREAM module question

Hi all,
I am newbe in STREAM module development and this question might be a concept error. If so, please could you give me some clues?
I would like to use the "libc" funcion "getpwuid()" in a kernel STREAM module.
I have Solaris 7 64-bit kernel.
�Can I do it? I have read that for 64-bit kernels, only dynamic libraries are available. Therefore in order ot use libc functions I would have to link dynamically the module relocatable object with the libc library in sparcv9. I have tried to link the kernel STREAM module with libc.so.1 (in /usr/lib/sparcv9) with no success so far. Everytime I trie to load the module it complains with the message: unknown symbol "getpwuid".
If it is not possible, why? . Is it not possible to use libc functions such us: memcpy() etc..from the kernel context?
Looking forward to hearing from you.
Best Regards

You cannot use user space libraries from within a kernel module. What exactly are you trying to
do? What do you need password information for
down in the kernel?
Maybe ddi_get_cred() will help?
Some functions like memcopy have kernel space equivalents (bcopy)....
dan

Fastethernet module question.

I understand that the NM-1FE Fastethernet modules are not compatible with Cisco 2600 series routers, just the Ethernet 1-E module. With that being said, are there ANY modules supported by the 2600, 2621 or 2621XM series routers that have fastethernet port(s) outside of the pricey NM-16ESW module? I don't need a 16 port module!

I think you would spend less and get better results replacing that 16-years old model with it e.g. an 851, or 871. These have FE, almost current IOS, and much better performances.

Array Module Question

Hi,
I am currently working on designing phase for an Array Module. We are planning to track the Array information and store it's content to database. Currently I am finalizing the data model and I have following question.
--We need to track the Geneology of the Sample through out the whole system (Especially the results of Transfers). Is it better to have all that relationship in one flat table with columns for location (like PlateWell, GelLane..) and columns for Content (Column like . LocationType LocationId ContentType ContentId) or is it better to store all the content of location as a ArrayType? Or is there any other option available in the Market?
In the first case database rows for that table will increate very very fast plus to find out the geneology of the location in Array , I have to use Connect By Prior which will take good amount of time(Is there any other option available?). I dont have much idea about second option but I think retrieval individual content is going to be a problem.
Any help is really appreciated.
Thanks in Advance
Raj

Made a complete example:
String searchKey = "Juice";
TreeMap tm = new TreeMap();
tm.put("soda", "coke");
tm.put("Juice", "orange");
tm.put("SODA", "7-up");
Set set = tm.entrySet();
Iterator iterator = set.iterator();
while( iterator.hasNext() ) {
Map.Entry entry = (Map.Entry)iterator.next();
if(entry.getKey().equals(searchKey)){
System.out.println("searchKey '"+searchKey+"' value is: "+entry.getValue());
What do you think? Anything obvious that can be improved?

Robotic module Question

Hi all
i have some question about the robotic module.
i already have a DH table for my robto arm.
Now i am trying to input this DH parameters into Labview.
I saw the example of inverse kinematis for puma 560.
Also,I find that the "create PUMA 560 Modified.Vi" can let user to input their only DH parameters.
But
What is the Twist in Labview? angle about previous Z, from old X to new X.
What is the Length in Labview? is it represent thelength of the common normal (r).
What is the Offset in Labview?offset along previousZ to the common normal.
What is the Joint Corrdinate Offseti? in Labview?offset along previousZ to the common normal.
When i modify the DH paramters into "set kinematic parameter.vi",there show a error about -310040.
Anyone can indicate which part i get worg?
Thank you so much
Tim
Attachments:
Inverse Kinematics for Puma 560 org Test.vi ‏34 KB
Test_PUM_560_tim.vi ‏32 KB
myrobotarm.jpg ‏98 KB

Hi Tim,
Thanks for your question. Are you attempting to modify the "create PUMA 560 Modified.vi" that you mentioned using your DH parameters, or are you modifying the "Test_PUM_560_tim.vi" example VI that you attached? The "Inverse Kinematics for PUMA 560 org Test.vi calls the "Test_PUM_560_tim.vi" so if you are using this example as a model, you would have to input your parameters (Length, Twist, Offset which you mentioned) into that VI.
The particular error you are getting (-310040) corresponds to the following error message: "LabVIEW cannot converge to a solution in the number of steps you specified. Make sure that the serial arm can achieve the transform you desire." This could be due to the fact that the current constraints are over defined.
Here is a link to the Robotic Help Manual:
http://zone.ni.com/reference/en-XX/help/372983D-01/
If you would like to give me some more information about your application, I would be happy to help further. Which version of LabVIEW are you using, and which version of the Robotics Module are you working with?
Good luck!
R. Brill
Applications Engineer
National Instruments

Very basic modules questions (ath_pci, etc)

Hello! (I'm sorry, I posted this one in another forum first, thinking I was posting it in this one :oops: )
I have a very simple question:
Where can I find modules (e.g., ah_pci for my Atheros mini PCI wireless card), and where and how do I install them?
For example, when I do:
modprobe ath_pci, I get a message saying something like:
can't find ath_pci module;
although I've seen a directory with this name on my system (IIRC, under /sys/drivers???).
Other example:
I have a 855GM Intelchipset. How do I find the module for it and how do I install it?
Thanks a lot.

Thanks for the reply, and for deleting the other thread.
I looked for /lin/modules, and I don't have a /lin directory... Is it normal?
Or maybe you meant /bin/modules...? Anyway, I looked for this too and there is no /modules directory under /bin.
I found some modules under /sys/module. There is one named ide_cd that I put in the MODULES array of rc.conf (just for a test, I don't know why it is for...), but I get a message at bootup:
[/code]FATAL: module ide_cd not found[code]
Is this normal too? Or it has to be compiled with the kernel to work. And BTW, if I compile the kernel (I don't think I'm at this point in Linux yet!), do I loose my installation or if everything stays in place in my system?
Thanks a lot![/code]

NM-16AM module question in my cisco 3660

Similar Messages

Maybe you are looking for