NM-2V with VIC-FXO card

I have a 2621xm router. Can someone tell me which Network Module I need to get to support either 2 VIC-2FXO cards or 1 VIC-4FXO card. And these hardwares will be use in India so I also need to know which VIC-FXO card I need to get for India. Thank you in advance !!!
I understand the VIC-4FXO is universal but not sure of the VIC-2FXO.
Any helps will be greatly appreciated !!
Danny

Those cards work with NM-1V and NM-2V
(Currently EoS)
Customers are encouraged to migrate to the Cisco IP Communications Voice/Fax Network Modules (NM-HD-xx) and associated VICs. The Cisco IP Communications Voice/Fax Network Modules (NM-HD-1V, NM-HD-2V and NM-HD-2VE) support all the features of the current low density voice/fax network modules (NM-xV) while offering significant advantages such as higher port and channel densities and a new generation of digital signal processors (DSPs) with greater memory and processing power
This link contains the info you want.
http://www.cisco.com/en/US/products/hw/modules/ps5365/products_data_sheet0900aecd801c595e.html

Similar Messages

Show ringing status on FXO card.

Hi all,
This might sound a bit nit pickey, but you know that when you typically dial out on a T1 or other digital line, it show on the phone the it is ringing. That is basically what I want to do with my FXO card. I would like the CM or Gateway to hear the tones, and send the Cisco Call Manger ringback status, out-of-service, and end-call. So that when I, or anyone, dials a number out, it shows it ringing, instead of connected, while it is still ringing.
Thank you for all your help.
Sincerly,
JZci

Hi Jonathan,
Just as an update, i made the changes on the config of the FXO card but the port still doesnt go to on-hook after a call is dropped. I however observed that this only happens when it is an incoming call. All incoming calls land on the IVR. So when I call in, I disconnect the call just after the attendant starts talking. When I check the status of the port, it remains off-hook till I shut down the port or disconnect the telephone line physically from the FXO card.
After applying echo-cancel enable and supervisory disconnect anytone commands, here is the config I have on the router now:
voice-port 2/0/0
supervisory disconnect anytone
cptone NG
timeouts call-disconnect 3
timeouts wait-release 3
connection plar opx 21000
description FXO CONNECTION TO PSTN
caller-id enable
I removed the following commands:
compand-type a-law
impedance complex2
Would appreciate any further suggestions.
Regards,
Femi

Cisco UCS C220 with VIC 1225

Hello,
We have Cisco UCS C220 M3 with VIC 1225 card installed. We connected only one 10G port of VIC 1225 to Nexus 5548UP switch. But I do not see this port on switch and in CIMI the status for this port shows Link Down. I wanted to to iSCSI boot from storage NetApp FAS2240 but since I don't see this port on my Nexus switch I am unable to do boot from NetApp. I tried both ports on VIC 1225 with same result. Please I need help in this matter. I know I am missing something very simple but can't figure this out.
Thanks,
Salman

Hi Kenny,
Here is the answers:
-What slot is this card installed in?
Mezzenine
-How many CPUs does the server have installed? (1 OR 2 CPUs can make the difference)
2x 2.90 GHz E5-2690/135W 8C/20MB Cache/DDR3 1600MHz
-Is the PCIe slot enabled in BIOS? << Let us know if you don't know how to check it from CIMC
I believe I did. Server>BIOS>BIOS advanced> PCIe (Let me know if this correct)
-Have you confirmed that the cable is good?
I have changed four cables. I am using SFP-H10GB-CU2M= Twinax cable.
-If the switch does not even see the port and CIMC says it is down, have you confirmed the switch port is properly configured?
CIMI says “Link Down” in VIC adapter General area. The switch interface config has only “switchport mode access” in default vlan 1.
-What is the firmware running on the server and the OS?
We upgraded the firmware with latest ucs-c220-huu-1.5.4-3.iso.
Let me share with you the complete BoM of the server:
UCSC-C220-M3S              1x UCS C220 M3 SFF w/o CPU mem HDD PCIe PSU w/ rail kit
UCS-CPU-E5-2690              2x 2.90 GHz E5-2690/135W 8C/20MB Cache/DDR3 1600MHz
UCS-MR-1X082RY-A    16x 8GB DDR3-1600-MHz RDIMM/PC3-12800/dual rank/1.35v
CAB-9K10A-UK              2x Power Cord 250VAC 10A BS1363 Plug (13 A fuse) UK
UCSC-PCIE-CSC-02    1x           Cisco VIC 1225 Dual Port 10Gb SFP+ CNA
UCSC-PCIE-QSFP              1x Qlogic QLE8242-CU Dual Port 10 GbE FCoE CNA
UCSC-HS-C220M3              2x Heat Sink for UCS C220 M3 Rack Server
UCSC-RAIL1              1x Rail Kit for C220 C22 C24 rack servers

UC 540 VIC 4 FXO CARD ADDITION IN VIC EXPANSION SLOT

Dear all,
I would like to add an additional VIC 4 FXO card in UC 540 expansion slot. Can I add additional VIC 4 FXO card without adding DSP modules.?
Same device I have to create auto attendant system. What are the licence required for auto attendant feature ?
Products details are given below
UC 540 VIC 4 FXO CARD ADDITION IN VIC EXPANSION SLOT
Cisco UC540W-FXO-K9 (MPC8358) processor (revision 0x100) with 235520K/26624K bytes of memory.
MPC8358 CPU Rev: Part Number 0x804A, Revision ID 0x20
30 User Licenses
10 FastEthernet interfaces
2 terminal lines
1 Virtual Private Network (VPN) Module
4 Voice FXO interfaces
4 Voice FXS interfaces
1 Voice MoH interface
1 802.11 Radio
1 cisco service engine(s)
128K bytes of non-volatile configuration memory.
250880K bytes of ATA CompactFlash (Read/Write)
Regards,
Ajay Jose K

Hi Emmanuel Valdez,
Thank you for your support.
We are not using conference and Transcoding in our network.We have built in VIC 4 FXO and VIC 4 FXS in our system.When I go through show dsp farm
Dspfarm Profile Configuration
Profile ID = 1, Service = CONFERENCING, Resource ID = 1
Profile Description : DO NOT MODIFY, active CCA conference profile - CCA2.0 codec711
Profile Service Mode : Non Secure
Profile Admin State : UP
Profile Operation State : ACTIVE
Application : SCCP Status : ASSOCIATED
Resource Provider : FLEX_DSPRM Status : UP
Number of Resource Configured : 4
Number of Resource Available : 4
Maximum conference participants : 32
Codec Configuration: num_of_codecs:2
Codec : g711alaw, Maximum Packetization Period : 30 , Transcoder: Not Required
Codec : g711ulaw, Maximum Packetization Period : 30 , Transcoder: Not Required
SLOT DSP VERSION STATUS CHNL USE TYPE RSC_ID BRIDGE_ID PKTS_TXED PKTS_RXED
0 3 28.3.5 UP N/A FREE conf 1 - - -
0 3 28.3.5 UP N/A FREE conf 1 - - -
0 4 28.3.5 UP N/A FREE conf 1 - - -
0 4 28.3.5 UP N/A FREE conf 1 - - -
Total number of DSPFARM DSP channel(s) 4
Can I use auto attendant system with out CUE ?
Thanks&Regards,
Ajay Jose K

Need to test a bunch of FXO cards.

I am tasked with testing a bunch of FXO cards (VIC-2FXO) and I have a 1760 router with an FXS card in it. I configured the router so that when I call from an IP phone (ext 4000) to the FXS card port 1/0 (ext 4015) it calls the FXO card on port 0/0 which uses plar to ext 4444 which is port 1/1 on the FXS card.
I also tried to plar calls to ext 4001 an IP phone.
When I call 4015 from the IP phone, it rings the 4444 extension once then the FXS port 1/0 (ext 4015) hangs up. A call remains between the FXO port 0/0 and the FXS port 1/1 but since the FXS port 1/0 dropped off you can not talk to the IP phone.
4001 calls ---> 4015 FXS 1/0 which rings ---> FXO 0/0 using PLAR rings ---> 4444 which is on FXS port 1/0
The port light for FXS 1/0 comes on during the call proces but then goes out. The port lights for the FXO 0/0 and FXS 1/1 stay light until I unplug th RJ11 cable between them.
Any ideas how I can keep FSX 1/0 from dropping one the call is answered on FXS 1/1?
Current configuration : 1917 bytes
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname Router
boot-start-marker
boot-end-marker
no aaa new-model
memory-size iomem 15
voice-card 0
voice-card 1
interface FastEthernet0/0
ip address 192.168.69.200 255.255.255.0
speed auto
voice-port 0/0
connection plar 4444
voice-port 0/1
voice-port 1/0
station-id number 4015
voice-port 1/1
station-id number 4444
dial-peer voice 400 pots
destination-pattern 4015
port 1/0
dial-peer voice 200 pots
incoming called-number .
port 0/0
dial-peer voice 444 pots
destination-pattern 4444
port 1/1
telephony-service
max-ephones 6
max-dn 6
ip source-address 192.168.69.200 port 2000
auto assign 1 to 6
max-conferences 4 gain -6
transfer-system full-consult
create cnf-files version-stamp Jan 01 2002 00:00:00
ephone-dn 1 dual-line
number 4000
ephone-dn 2 dual-lin
number 4001
ephone 1
no multicast-moh
mac-address 000A.8AF0.3016
type 7960
button 1:1
ephone 2
no multicast-moh
mac-address 001B.535C.CABD
type 7940
button 1:2
line con 0
line aux 0
line vty 0 4
login
end
Thanks

Michael,
I have seen issues like this and its all dow to actual physical wiring.
Your 2 port FXS & FXO cards have 2 lines available on each port.
Can you ensure that you wire everything as a single 2 wire.
FXS 1/0 RJ11 PIN3 ------------------------------------------------- FXO 0/0 PIN 3
FXS 1/0 RJ11 PIN4 ------------------------------------------------- FXO 0/0 PIN 4
FXS 1/1 RJ11 PIN3 ------------------------------------------------- EXT 4444
FXS 1/1 RJ11 PIN4 ------------------------------------------------- EXT 4444
Do not put through any other wires
Regards,
Alex.
Please rate useful posts.

FXS versus FXO cards in 2821

I am new to Cisco CME and VOIP and am trying to configure a new 2821 with CME 4.1. I have two 4 port FXS cards. The intent was to use the ports on these cards to connect to PSTN POTS lines for inbounce and outbound cards. Can I use these FXS cards for this purpose or do they need to be FXO cards? According to the description they do as the FXS is intended to have phones connected and supplies dial-tone and the FXO does not supply dial-tone and is intended to be connected to PSTN. The reason that I am a little confused is that I have configured the system to dial out but was having issues where it would not hang up the line.

Hi Michael,
Here is some background info to add to Paolos always Great info (hey P.);
Analog Telephony Protocols
Analog telephony signaling, the original signaling protocol, provides the method for connecting or disconnecting calls on analog trunks. By using direct current (DC) over two-wire or four-wire circuits to signal on-hook and off-hook conditions, each analog trunk connects analog endpoints or devices such as a PBX or analog phone.
To provide connections to legacy analog central offices and PBXs, Cisco CallManager uses analog signaling protocols over analog trunks that connect voice gateways to analog endpoints and devices . Cisco CallManager supports these types of analog trunk interfaces:
Foreign Exchange Office (FXO) Analog trunks that connect a gateway to a central office (CO) or private branch exchange (PBX).
Foreign Exchange Station (FXS) Analog trunks that connect a gateway to plain old telephone service (POTS) device such as analog phones, fax machines, and legacy voice-mail systems.
From this good doc;
http://www.cisco.com/en/US/products/sw/voicesw/ps556/products_administration_guide_chapter09186a00801ec5cc.html#1134121
FXS and FXO Interfaces
An FXS interface connects the router or access server to end-user equipment such as telephones, fax machines, or modems. The FXS interface supplies ring, voltage, and dial tone to the station and includes an RJ-11 connector for basic telephone equipment, keysets, and PBXs.
An FXO interface is used for trunk, or tie line, connections to a PSTN CO or to a PBX that does not support E&M signaling (when local telecommunications authority permits). This interface is of value for off-premise station applications. A standard RJ-11 modular telephone cable connects the FXO voice interface card to the PSTN or PBX through a telephone wall outlet.
FXO and FXS interfaces indicate on-hook or off-hook status and the seizure of telephone lines by one of two access signaling methods: loop start or ground start. The type of access signaling is determined by the type of service from the CO; standard home telephone lines use loop start, but business telephones can order ground start lines instead.
Loop-start is the more common of the access signaling techniques. When a handset is picked up (the telephone goes off-hook), this action closes the circuit that draws current from the telephone company CO and indicates a change in status, which signals the CO to provide dial tone. An incoming call is signaled from the CO to the handset by sending a signal in a standard on/off pattern, which causes the telephone to ring.
Loop-start has two disadvantages, however, that usually are not a problem on residential telephones but that become significant with the higher call volume experienced on business telephones. Loop-start signaling has no means of preventing two sides from seizing the same line simultaneously, a condition known as glare. Also, loop start signaling does not provide switch-side disconnect supervision for FXO calls. The telephony switch (the connection in the PSTN, another PBX, or key system) expects the router's FXO interface, which looks like a telephone to the switch, to hang up the calls it receives through its FXO port. However, this function is not built into the router for received calls; it only operates for calls originating from the FXO port.
Another access signaling method used by FXO and FXS interfaces to indicate on-hook or off-hook status to the CO is ground start signaling. It works by using ground and current detectors that allow the network to indicate off-hook or seizure of an incoming call independent of the ringing signal and allow for positive recognition of connects and disconnects.
From this very descriptive doc;
http://www.cisco.com/en/US/products/sw/iosswrel/ps1835/products_configuration_guide_chapter09186a0080080afd.html
Hope this helps!
Rob

CME FXO Card

We have an fxo card that used to work with an intercom. It is no longer working. No configs changed or anything. Is there any command or method of testing an FXO card in a CME>

You can open a TAC case and collect some details debugs, if you have a contract.
You can also try changing ports (and the configuration for the related port) to see if it happens on another port.
May also want to check deeper into your network to see if anything else has changed.
For instance, upgrading from CUCM 6 to CUCM 7 would change your phone loads, and the phone load in CUCM 7 by default has a nasty duplicate DTMF bug. This duplicate DTMF bug may be causing users to dial the wrong number when they dial in. (If your IP phones are 8.4.1 or 8.4.1 sr 1 this is the problem).
You can check show diag to make sure the board is 'analyzed' and doesn't have an error message related to it.
But there is no 'check hardware' command or anything like that.
hth,
nick

FXO card disconnect issues!!!!!!!!!! IS this a bug !!!!!!!!!! help out !!!!

I have 2620 router with fxo card. The call is not disconnecting at the fxo side after the call is complete. This issue is happening only with PBX. With PSTN no problem.
I tested all options of our discconecting FXO card from cisco site. It didn't help.
Whether this is bug !!!!!!!!!!! help out guys!!!!!!!!!!!
Anybody faced similiar issues
Thankx

hi
we are facing the same issue : also be careful of the fxo as a source of crosstalk
I will let you know when we have these issues resolved

Mac with airport card and PC with wi-fi card

Hi!
I just bought my first mac, and strange, but I have problems connecting my mac via airport extreme card to my wi-fi card (as computer-to-computer or ad-hoc mode) on my PC. I am not using base station or any wi-fi router, just two computers with their internal cards.
PC has WinXP pro with SP2 and mac - imac g5. The problem is that both of the cards are enabled and are working on 100%, but they do not see each other! I tried to create a wireless network on my PC and then search for this network from mac and vice versa - nothing. By the way my notebook finds the PC's newly created network with no problem, but not the mac.
What could be wrong? Is it possible, that it's nessesary to use the base station with them?
iMac G5 Mac OS X (10.4.3) OS Tiger

anyone?

UCS C420M3 server with VIC 1225 , Cant see LOM ethernet ports

Hi Guyz,
we have C420M3 server with VIC 1225 connected on PCIe slot, with Fabric Interconnet.
After installing OS & drivers , vNICs created on VIC 1225 by service profile appear, but 4 gig ports on Server LOM dont appear.
Any Idea.?
Thank

If you integrate your rack server to UCSM, you will be able to use the LOM ports ONLY for Mgmt traffic, that is when you integrate the server in "Dual Wire Mode".
There is no need (unless you have one for an special reason I am not considering in this very moment) to use the LOM ports once you have integrated the server, precisely cause the VIC 1225 is a not a regular NIC card, nor a regular HBA, it is actually a CNA (Converged Network Adapter) which basically lets you do in one card, what you would do with two (meaning "what you would do with a separate NIC and HBA")
When you have a VIC card, you actually have the option to create up to 256 virtual interfaces (that's the capability of the hardware, always limited by the OS used, please keep that in mind), that is the reason why, after the server is integrated, you totally depend on the interfaces set in the Service Profile instead of the physical interfaces.
Find more info here:
http://www.cisco.com/c/en/us/products/interfaces-modules/unified-computing-system-adapters/models-comparison.html
Do you have a particular reason for using the LOM ports instead of creating 2 additional virtual interfaces in the Server's Service Profile?
-Kenny

Fxo card is not connecting dtmf calls

I have an analogue line that is being set up from GSM modem and connected to fxo card on VG router .The fxo card is configured to go to an automated message with option of pressing digits to take one to the right operator.i.e press 1 for....,2 for......,etc. Unfortunately,this is not working when i callled the number.Its looking like a DTMF issue,but i ve adjusted all the seeting that has to do with dtmf on the fxo card......Has anyone encounter any familiar issue?

Check to see if you have the voice license bundle for the router.
show license
Index 3 Feature: uck9
Period left: Life time
License Type: Permanent
License State: Active, In Use
License Count: Non-Counted
License Priority: Medium
Without the voice license, no voice ports can be configured on 2900 series routers.

SQL Clustering on C Series server with QLE8152-CNA cards

Is there any documentation on best practices when installing Windows on a c series server
with QLE8152-CNA cards for SQL clustering? Since it will be a bare metal install of Windows, this card will only present a maximum of 2 nics (FI A and FI B) to the Windows OS and because SQL clustering requires multiple nics (heartbeat, regular network), I wanted to know whethere there are guidelines on how to do this or whether it is even supported. I intend on using the failover feature in UCS Manager 1.4 when creating a service profile for these c series server which means I'll end up with 1 NIC presented to the Windows server. Thanks.

Hi Keny,
I tried to powercycle both servers (c260M2 and C460M2) but still no discovered server and also no logg.
I checked
Rack Server Discovery Policy == immediate
Rack management Connecton Policy == Auto Achnowledged
Chassis/Fex Doscovery Policy == 2 Link and Port-Channel (As I installed 2232PP I moved to Port Channel)
I am running UCSM Version 2.1(1e)
FI 6248 Version 5.0(3)N2(2.11e)
2232PP run on same as FI
I also have a connected 5108 with IOM 2104 running on 2.1(1e) Version.
CIMC Version of C260M2 and C460M2 will be checked tomorrow when my kolleague is in the datacenter.
Server Connection is not really the same like in http://www.cisco.com/en/US/docs/unified_computing/ucs/c-series_integration/ucsm2.1/b_UCSM2-1_C-Integration_chapter_011.html
Because I still have no VIC Card but the connections are the same.
C260 GE LOM1 <-> FEX2 Port 11
C260 GE LOM2 <-> FEX3 Port 11
C260 10 GE LOM1 (PCIE Slot4) <-> FEX2 Port 12
C260 10 GE LOM2 (PCIE Slot4) <-> FEX3 Port 12
GE LOM ist position 13 and 10 GE LOM is position 11 in the techspech of c260
http://www.cisco.com/en/US/docs/unified_computing/ucs/c/hw/C260/install/overview.html#wp1243740
C460 GE LOM1 <-> FEX2 Port 10
C460 GE LOM2 <-> FEX3 Port 10
C460 10 GE LOM1 <-> FEX2 Port 9
C460 10 GE LOM2 <-> FEX3 Port 9
GE LOM ist postion 8 and 10 GE LOM ist position 7
http://www.cisco.com/en/US/docs/unified_computing/ucs/c/hw/C460/install/overview.html#wp1243740
With C260 I also tried a reboot with disconnected 10 GE Ports, but also no discoverd Server until now.
Regards Alois

Syslog and FXO card

I have a 2811 with one four-port FXO card; 4 POTS lines are connected to it. Syslog is configured on the router, sending traps (debug level) to a host. For some reasons, I do not get any info in syslog form the card; so making or receiving a call sends nothing. Any ideas?
Thanks, S.

This is the normal, making and receiving calls do not generate syslog output. If you want output, either enable some debug permanently, or use a radius server for exact accounting.
Hope this helps, please rate post if it does!

How do I activate a used iPhone 3 with no SIM card for use as an ipod touch?

How do I activate a used iPhone 3G with no SIM card for use like an iPod Touch? It was apparently on AT&T previously and I have another iPhone 3 that is active on AT&T if that is helpful. Thanks!

Copied from the link provided.
Follow these steps to use your iPhone without a wireless service plan:
Insert the SIM card from your new, activated iPhone or one that was previously used to activate the original iPhone.
Connect the iPhone to iTunes on a computer connected to the Internet.
Once iTunes activates the device, you're free to use the iPhone as if it were an iPod touch.

Dear sir I bought my iPhone 4 from Apple store in Charlotte N/C about 2years ago without contract. Now I tried to upgrade it to iOS 7.0.4.but after that my phone not work with last sim card. And invalid sim appeared.so I bought it without contract but it

Dear sir
I bought my iPhone 4 from Apple store in Charlotte N/C about 2years ago without contract.
Now I tried to upgrade it to iOS 7.0.4.but after that my phone not work with last sim card.
And invalid sim appeared.so I bought it without contract but it seems to be lock in my country
Please tell me whats the matter?
My phone serial no 86034HTCA4T
Modem firmware 04.12.09
Thanks

Without contract is not the same as unlocked. The update to iOS 7 relocked
the iPhone to the wireless carrier to which it was originally locked. You must
contact that wireless carrier to see if they offer unlocking and if you qualify.
If you used jailbreak or other hack to unlock the iPhone initially, the method
used may prevent a legitimate unlock from succeeding and may render your
iPhone unuseable.

NM-2V with VIC-FXO card

Similar Messages

Maybe you are looking for