NM-HDA-4FXS in Cisco 2610

Hi, can I use NM-HDA-4FXS in "old" Cisco 2610 router (not XM series). I have tried it with a few different IOS version (12.2.15T, 12.3.9) and different feature set (PLUS, ENTERPRISE PLUS, ,,,) and still I have message that card in bay #1 (NM slot) is not correctly recognized (%PA-2-UNDEFPA: Undefined Port Adaptor type 22C in bay 1).
On CCO I found information that in Plus soft 12.2.2T and above Cisco 2610 serves NM-HDA.
Any suggestions ?
Thank a lot
Maciej

Hi
hope this link will help u out to get the exact compatible ios for u r H/W.
http://tools.cisco.com/Support/Fusion/FusionHCHome.do
regds
prem

Similar Messages

Cisco 2610 and nm-16a

Hi,
I have problem with configure ppp on nm-16a. I have 2 modems motorola uds v.3400 ,and one is connected to the windows 2000, and second to nm-16a. I want connect from windows 2000 pc with modem to the router by modem. I have tested this with the same modems and router motorola vanguard-320 and was ok.
Current configuration:
version 12.0
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
hostname Router
username ppp
ip subnet-zero
interface Ethernet0/0
no ip address
no ip directed-broadcast
shutdown
interface Serial0/0
no ip address
no ip directed-broadcast
no ip mroute-cache
shutdown
interface Group-Async1
no ip address
no ip directed-broadcast
autodetect encapsulation ppp
async mode interactive
ppp authentication chap
group-range 33 48
ip classless
line con 0
transport input none
line 33 48
password ppp
login
modem autoconfigure discovery
full-help
line aux 0
line vty 0 4
no scheduler allocate
end

Hello,
not sure if this problem still exists for you, but have a look at the document below, it includes a sample configuration for dialin:
Configuring Dialin with the NM-8AM or NM-16AM Analog Modem Module
http://www.cisco.com/en/US/partner/products/hw/modules/ps2740/products_configuration_example09186a00800e0dcd.shtml
HTH,
GP

2610 LAN configuration with devices on both internal and external IPs

I am more than a bit rusty and reconfiguring a network due the arrival of a new SBS office server. The new office server (and clients) needs to connect to the Internet via our Cisco 2610 router. The server is say 10.1.1.10 and the FastEthernet0 interface on the router is set to 10.1.1.200. The 2600 has a Serial0 interface that is connected to a leased line with an external IP address. We also have our own class C IP range used for web, mail and dns servers.
So:
OfficeServer (10.1.1.10)<----->FastEthernet0(10.1.1.200)[2600 ROUTER1]Serial0(123.123.123.54)<---leased line--->ISP(Internet)
However, I also have a webserver etc in our office, with an external IP address from our range, that needs to, and can, see the Internet.
So, we also have, on the same router:
WebServer (90.4.123.35)<----->FastEthernet0(90.4.123.254)[2600 ROUTER1]Serial0(123.123.123.1)<---leased line--->ISP(Internet)
interface FastEthernet0/0
ip address 10.1.1.200 255.255.0.0 secondary
ip address 90.4.123.254 255.255.255.0
ip nat inside
speed auto
full-duplex
interface Serial0/0
description Connection to NTL
ip address 123.123.123.54 255.255.255.252
ip broadcast-address 123.123.123.55
ip access-group inboundfilter in
ip access-group outboundfilter2 out
ip nat outside
encapsulation ppp
no fair-queue
The FastEthernet0 interface has both an internet and external IP address mapped to it. Currently the office PCs use the external IP address as their gateway address and this works, however the new server is more secure and won't allow this.
There is NAT and access-lists running on the Cisco and each office PC has an internal IP address that is NATted to a dedicated external IP.
At the moment the webserver can see the Internet, but the office server cannot. Office PCs can see the Internet if they use the external IP address mapped to FastEthernet0/0 direct as their gateway address (although you get a message suggesting that this is not the way to go). So I am trying to resolve this whilst also trying to set it up better/properly.
What is the best way to do this (all assistance appreciated)?
Do I need to NAT the internal office server IP to an external IP address for it to see the internet?
Do I need to NAT the internal gateway address to an external IP address or will the router be able to route this anyhow?
Could it be DNS, so should I set the DNS server on the office server NIC to the ISPs DNS server, or to the Cisco

The best solution is to renumber the webserver to an internal ip address and configure a static nat on the router:
ip nat inside source static
http://www.cisco.com/en/US/docs/ios/12_3/12_3x/12_3xe/feature/guide/gt_ntsip.html
regards,
Leo

802.1q support on 2610 router built-in eth interface

I read in an official Cisco document that support for 802.1q on built-in ethernet interfaces on routers was enabled for recent IOS versions. I installed an recent IOS version and still giving me a hard time. Any ideas?
I attached the document.

the ping is responding ok but the network services are pretty slow, here is the show version output:
CusSanJoseRou1#sh version
Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-IS-M), Version 12.2(34a), RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2006 by cisco Systems, Inc.
Compiled Tue 02-May-06 11:58 by pwade
Image text-base: 0x8000808C, data-base: 0x8111CF0C
ROM: System Bootstrap, Version 11.3(2)XA4, RELEASE SOFTWARE (fc1)
CusSanJoseRou1 uptime is 1 week, 5 days, 5 hours, 29 minutes
System returned to ROM by reload
System image file is "flash:c2600-is-mz.122-34a.bin"
cisco 2610 (MPC860) processor (revision 0x202) with 45056K/4096K bytes of memory.
Processor board ID JAB0331000W (4147343804)
M860 processor: part number 0, mask 49
Bridging software.
X.25 software, Version 3.0.0.
Basic Rate ISDN software, Version 1.1.
1 Ethernet/IEEE 802.3 interface(s)
2 Serial(sync/async) network interface(s)
1 ISDN Basic Rate interface(s)
32K bytes of non-volatile configuration memory.
16384K bytes of processor board System flash (Read/Write)
Configuration register is 0x2102

Which version of IOS is required on Cisco 3640 to have Xconnect command?

Hi,
I want to to configure layer2 circuits on Cisco 3640 , If anybody can let me knowWhich version of IOS is required on Cisco 3640 to have Xconnect command?

Hi Harold,
I have a home lab having Cisco 3640, Cisco 2610 and Juniper J2320. I want to configure Layer-2 VPN/EoMPLS between Juniper J2320 and Cisco device.
Could you please guide me on these 2 below mentioned questions.
1) Does Cisco 2610 supports Layer-2/EoMPLS with any IOS. If so what IOS should I have to support Layer-2/EoMPLS on 2610.
2)Can you please confirm me that Cisco 2801 with IOS c2801-spservicesk9-mz.124-15.T9 will support Layer2/EoMPLS ?
While researching on this I cam to know that only 2801 with IOS c2801-spservicesk9-mz.124-15.T9 can support this , but not sure , need your guidance.
Based on your answer I will buy Cisco router 2801 for my Layer-2/EoMPLS setup.
Regards
Ranjeet

2610 Factory Reset and Startup Config Files

Hi all;
I have a used 2610 which I did a factory reset on. I am able to get into the IOS and edit/change the config.
However after editing and trying to save using the command:
copy run start
I get prompted to save the config to a file name/location which ultimately fails. Then on reboot it goes into the "basic setup" sequence again never saving to the config I'm trying to save.
The IOS ver. is 12.0(3)T and I do have the latest ver. and an TFTP program to upgrade, but I would like to create a config and save it first.
Any help would be appreciated.
Thanks in advance. Steve

Edison;
Thanks for the reply. Yes my register was 0x2142 but I did the "config-register 0x2102" and then was able to copy the running config to the startup config.
I do have another ?. I did type in a time offset command for my timezone but after reboot it keeps defaulting back to year 1993.
Here's my sh ver:
Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-I-M), Version 12.0(3)T, RELEASE SOFTWARE (fc1)
Copyright (c) 1986-1999 by cisco Systems, Inc.
Compiled Mon 22-Feb-99 20:00 by ccai
Image text-base: 0x80008088, data-base: 0x8069353C
ROM: System Bootstrap, Version 11.3(2)XA4, RELEASE SOFTWARE (fc1)
uptime is 14 minutes
System restarted by reload
System image file is "flash:c2600-i-mz.120-3.T"
cisco 2610 (MPC860) processor (revision 0x202) with 18432K/6144K bytes of memory
Processor board ID JAB03090910 (856765012)
M860 processor: part number 0, mask 49
Bridging software.
X.25 software, Version 3.0.0.
1 Ethernet/IEEE 802.3 interface(s)
2 Serial network interface(s)
32K bytes of non-volatile configuration memory.
8192K bytes of processor board System flash (Read/Write)
Configuration register is 0x2102
Thanks, Steve

5 users limitation using PPPoE on cisco??

Hello,
I am trying to use a cisco as a pppoe server. The problem is that its not able to connect mor e than 5 users at a time. I thought the cisco(3620) had some problems and used another (2610) with the same result. What could be the problem?
TIA
Shekhar Basnet
Here are some info.
System image file is "flash:c2600-ik9o3s-mz.122-31"
cisco 2610 (MPC860) processor (revision 0x203) with 61440K/4096K bytes of memory
32K bytes of non-volatile configuration memory.
16384K bytes of processor board System flash (Read/Write)
PPPoE# sho run
Building configuration...
ip audit notify log
ip audit po max-events 100
vpdn enable
vpdn-group canopy-consumer
accept-dialin
protocol pppoe
virtual-template 10
pppoe limit per-vlan 300
interface FastEthernet1/0.630
description #### PPPoE clients #####
encapsulation dot1Q 630
pppoe enable
interface Virtual-Template10
ip address 192.168.125.125 255.255.255.252
peer default ip address pool consumer-pool
ppp authentication pap
ip local pool consumer-pool x.x.254.112 x.x.254.119
Here's a sample log when trying to connect using a 6th customer
Feb 5 16:49:53: PPPoE 0: I PADI L:ffff.ffff.ffff R:000a.e44f.ba27 630 Fa1/0.630
Feb 5 16:49:53: PPPoE 0: O PADO L:f730.8100.0276 R:ba27.0003.e3e8 630 Fa1/0.630
Feb 5 16:49:53: PPPoE 0: I PADR L:0003.e3e8.f730 R:000a.e44f.ba27 630 Fa1/0.630
Feb 5 16:49:53: PPPoE 396: Creating
Feb 5 16:49:53: PPPoE 396: Created L:0003.e3e8.f730 R:000a.e44f.ba27 630 Fa1/0.630
Feb 5 16:49:53: PPPoE 396: O PADS L:0003.e3e8.f730 R:000a.e44f.ba27 630 Fa1/0.630
Feb 5 16:49:53: %LINK-3-UPDOWN: Interface Virtual-Access2, changed state to up
Feb 5 16:49:54: PPPoE 396: I PADT L:0003.e3e8.f730 R:000a.e44f.ba27 630 Fa1/0.630
Feb 5 16:49:54: PPPoE 396: Shutting down
Feb 5 16:49:54: PPPoE 396: O PADT L:0003.e3e8.f730 R:000a.e44f.ba27 630 Fa1/0.630
Feb 5 16:49:54: PPPoE 396: Destroying L:0003.e3e8.f730 R:000a.e44f.ba27 630 Fa1/0.630
Feb 5 16:49:54: %LINK-3-UPDOWN: Interface Virtual-Access2, changed state to down
PPPoE#sho idb
Maximum number of IDBs 300
24 SW IDBs allocated (2624 bytes each)
19 HW IDBs allocated (4976 bytes each)
HWIDB#1 1 Ethernet0/0 (HW IFINDEX, Ether)
HWIDB#2 3 BRI0/0 (HW IFINDEX, HW ISDN, Serial)
HWIDB#3 4 Serial0/0 (HW IFINDEX, Serial)
HWIDB#4 5 BRI0/0:1 (HW ISDN, Serial)
HWIDB#5 6 BRI0/0:2 (HW ISDN, Serial)
HWIDB#6 7 Serial0/1 (HW IFINDEX, Serial)
HWIDB#7 8 FastEthernet1/0 (DOT1Q, HW IFINDEX, Ether)
HWIDB#8 9 Virtual-Access1 (Serial, HW VACCESS)
HWIDB#9 10 Virtual-Access2 (Serial, HW VACCESS)
HWIDB#10 11 Virtual-Access3 (Serial, HW VACCESS)
HWIDB#11 12 Virtual-Access4 (Serial, HW VACCESS)
HWIDB#12 13 Virtual-Access5 (Serial, HW VACCESS)
HWIDB#13 14 Virtual-Access6 (Serial, HW VACCESS)
HWIDB#14 15 Virtual-Template10 (HW IFINDEX, Serial, HW VTEMPLATE)
HWIDB#15 16 Loopback0 (HW IFINDEX)

Yahoooo!! Success at last.. Thanks a lot Mak. But I would love to know the reason behind it. So even changing the subnet on VT to /24 would have had no effect then?
PPPoE#sho user
Line User Host(s) Idle Location
* 66 vty 0 shekhar idle 00:00:00 x.x.233.248
Interface User Mode Idle Peer Address
Vi1 silt Virtual PPP (PPPoE ) 00:00:05 x.x.225.35
Vi2 hhc123 Virtual PPP (PPPoE ) 00:00:15 x.x.225.37
Vi3 mahaguthi Virtual PPP (PPPoE ) 00:00:55 x.x.225.33
Vi4 atlas Virtual PPP (PPPoE ) 00:00:35 x.x.225.36
Vi5 hope Virtual PPP (PPPoE ) 00:01:35 x.x.225.34
Vi6 ktptest Virtual PPP (PPPoE ) 00:00:05 x.x.225.38
PPPoE#

20 Analog Trunks on CME 2911

Hi guys.
We have a current requirement that has the following specifications.
Minimum of 20 Analog trunks, 1 x E1 PRI ISDN trunk, with SIP license (60 licenses), with IVR, call data recording
I have configured a 2911 with the appropriate licenses in CCW. But, how can I come up with a solution for 20 analog trunks? I am not yet familiar with this.
Thanks in advance.

EVM-HD-8FXS/DID High density voice/fax extension module -8 FXS/DID
EVM-HD-8FXS/DID
The Cisco High-Density Extension Module for voice and fax
has 8 FXS and DID ports. Individual ports on the basebo
ard
module can be configured for FXS or DID signaling. Adj
acent ports should share the same configuration to avoid i
mpedance
setting conflicts. A change to the impedance setting for o
ne port, changes the setting on the adjacent port. Pair
ed ports are: 0
and 1; 2 and 3; 4 and 5; 6 and 7.
An on-premises FXS interface connects directly to a standar
d telephone, fax machine, or similar device and supplies
ring,
voltage, and dial tone. Signaling support available in
FXS mode includes loop-start and ground-start. DID tru
nks from the
central office can be connected to the Cisco High-Density E
xtension Module baseboard for off-premises connections.
Signaling support available in DID mode includes immedi
ate, delay dial, and wink start.
Users plug in up to two expansion modules in any combina
tion to increase the voice and fax capacity of the Cisco Hi
gh-
Density Extension Module baseboard.
or
EM3-HDA-8FXS/DID 8-port voice/fax expansion module-FXS/DID
EM3-HDA-8FXS/DID
This 8-port FXS/DID Voice and Fax Expansion Module pro
vides on-premises FXS signaling to connect directly to a sta
ndard
telephone, fax machine, or similar device and supplies ri
ng, voltage, and dial tone. Signaling support availabl
e in FXS mode
includes loop-start and ground-start. This expansion modu
le also works with the Cisco High-Density Analog Voice an
d Fax
Network Module (part number NM-HDA-4FXS).
DID trunks from the central office can be connected to t
he Cisco Voice and Fax Expansion Module for off-premises
connections. Signaling support available in DID mode incl
udes immediate, delay dial, and wink start. It support
s up to eight
ports in DID mode, both expansion slots combined (with ei
ght DIDs on EVM baseboard, up to 16 DIDs maximum).
Additionally, it supports robust front end protection.

Encapsulation command in subif

Greets,
I have a 2610 router and I am attempting to enable DOT1Q on eth0/0.1 for router-on-a-stick configuration.
My sh ver is as follows:
Router>sh ver
Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-I-M), Version 12.2(8)T5, RELEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/tac
Copyright (c) 1986-2002 by cisco Systems, Inc.
Compiled Fri 21-Jun-02 08:50 by ccai
Image text-base: 0x80008074, data-base: 0x80A2BD40
ROM: System Bootstrap, Version 11.3(2)XA4, RELEASE SOFTWARE (fc1)
Router uptime is 39 minutes
System returned to ROM by reload
System image file is "flash:c2600-i-mz.122-8.T5.bin"
cisco 2610 (MPC860) processor (revision 0x203) with 28672K/4096K bytes of memory.
Processor board ID JAD042108TF (1440777694)
M860 processor: part number 0, mask 49
Bridging software.
X.25 software, Version 3.0.0.
1 Ethernet/IEEE 802.3 interface(s)
32K bytes of non-volatile configuration memory.
8192K bytes of processor board System flash (Read/Write)
Configuration register is 0x2102
Now the problem is I can not enter the encapsulation command as you can see here:
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#int eth0/0.1
Router(config-subif)#encapsulation
^
% Invalid input detected at '^' marker.
Any reason for this? I thought IOS 12.2 should have dot1q capability.
Cheers

Hi Dan.
you're right as this document does.
http://www.cisco.com/en/US/products/hw/routers/ps259/prod_bulletin09186a00800921e4.html
But you need to make sure that by using the cisco navigator.
http://tools.cisco.com/ITDIT/CFN/jsp/index.jsp
As far as I see you should use c2600-is-mz.122-4.T.bin IOS that is IP-PLUS feature set.Kindly check the ios you want for sure!
Edit : Jon and Glen are absolutely right. I didn't see your replies.
Hopes this helps
Thot

Having trouble with AS2511 RJ configuration.

Hello all. Could someone give me advice on this issue, i think i have it close to being resolved but need a slight push in the right direction. Any help/advise would be great.
I am in the process of building my lab. MY current setup has 4 cisco 2610 and 2 2501s for backbone routers along with a frame switch and a 2511 rj term server.
I have set up 2 of my routers to connect through the frame switch and am configuring the console ports to allow me access via my terminal server.
Following is my setup
2610----frame switch----2610
term server
This is what i am a problem with. Both 2610s can talk to each other so i have ip connectivity. But when i try to connect on the console ports from the term serv i get a message saying. Trying r2 (172.16.1.1)... Open
Password required, but none set. Wierd thing is that both 2610s have the console password set. Config follows. So what gives? i know the config is saved and i have the right roll over cables connecting or else i would never even get the message saying password not set.
line con 0
password lab
line aux 0
password labs
login
transport input all
line vty 0 4
password lab
login
The term serv config follows.
Term_Server#sh ru
Building configuration...
Current configuration:
version 12.0
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
hostname Term_Server
ip subnet-zero
no ip domain-lookup
ip host r2 172.16.1.1
ip host r1 172.16.1.1
interface Loopback0
ip address 172.16.1.1 255.255.255.255
no ip directed-broadcast
interface Ethernet0
no ip address
no ip directed-broadcast
shutdown
interface Serial0
no ip address
no ip directed-broadcast
shutdown
no ip http server
ip classless
line con 0
transport input none
line 1 16
no exec
exec-timeout 25 0
transport input all
line aux 0
line vty 0 4
login
end
So can anyone help me with this? Please. Thx.

It looks like you are not hitting r2 through the console, you are hitting r2 via telnet.
If this is true, you should be able to put a password on vty 0 4 and sucessfully connect.
"Password needed and none set" is a telnet error ... not someting that would come from a console connection.
In your host definitions on the TermServer, remember to use a loopback address of te TermServer (along with the port 2001, 2002 ...).
Like: host r2 192.168.1.1 2002 <--192.168.1.1 is the loopback address of the termserver (itself).
Good Luck
Scott

After installing new image, why router keeps 'decompressing'?

I found similar posts but they say this could be due to oversized images. It doesn't seem to be my case. My router memory count below shows I have 64D,16F as shown on the bottom of the pasted info below, isn't that correct ?
I downloaded an image from cisco.com for my C2610. I loaded the image onto the router via rommon/TFTP.
Then I noticed that every time I power cycle the C2610, I get the message "self decompressing....".
I made sure that the respective image I am trying to load, the 'c2600-j1s3-mz.123-16.bin' is supported by 64D and 16F routers. Note that is originally an image for 2610XM routers, however, before I downloaded an image for C2610 version 12.3 which also presented same problem.
Note that router was functional before I did this image download exercise.
Please advise what could be wrong and how I can get rid of this annoying 'decompressing' messages every time I start up router.
Router(config)#config register -register 0x2102
Router(config)#
Router#wri m
*Mar 1 00:08:37.904: %SYS-5-CONFIG_I: Configured from console by consoleem
Building configuration...
[OK]
Router#
System Bootstrap, Version 11.3(2)XA4, RELEASE SOFTWARE (fc1)
Copyright (c) 1999 by cisco Systems, Inc.
TAC:Home:SW:IOS:Specials for info
C2600 platform with 65536 Kbytes of main memory
program load complete, entry point: 0x80008000, size: 0xf427d8
Self decompressing the image : ################################################################################################################################################################################################################################################################## [OK]
Smart Init is enabled
smart init is sizing iomem
ID MEMORY_REQ TYPE
000091 0X0008B800 C2600 single Ethernet
0X00098670 public buffer pools
0X00211000 public particle pools
TOTAL: 0X00334E70
If any of the above Memory Requirements are
"UNKNOWN", you may be using an unsupported
configuration or there is a software problem and
system operation may be compromised.
Rounded IOMEM up to: 4Mb.
Using 6 percent iomem. [4Mb/64Mb]
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-J1S3-M), Version 12.3(16), RELEASE SOFTWARE (fc4)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2005 by cisco Systems, Inc.
Compiled Tue 23-Aug-05 17:45 by ssearch
Image text-base: 0x80008098, data-base: 0x81A2BE04
cisco 2610 (MPC860) processor (revision 0x300) with 61440K/4096K bytes of memory.
Processor board ID JAD054809DU (1862059776)
M860 processor: part number 0, mask 49
Bridging software.
X.25 software, Version 3.0.0.
TN3270 Emulation software.
1 Ethernet/IEEE 802.3 interface(s)
1 Serial network interface(s)
32K bytes of non-volatile configuration memory.
16384K bytes of processor board System flash (Read/Write)

Hi,
you can unzip the image using gzip or any other ZIP program (on a MS PC rename it to *.zip). It contains the "real" binary, which is about 2-3 times larger. Never tried to boot directly, but in principle this should also work. Just be aware, that the unzipped IOS might not fit into flash anymore.
Hope this helps! Please rate all posts.
Regards, Martin

Suspect.BUG in CW voice manager2.3 HELP,please!!!!!!!!

hi...
we are getting data for "dialCtlPeerCallInformation" and "dialCtlPeerCallSetup",only from one router among a group of routers...all the routers are added to the cvm in the similar fashion...from router model 3661
IOS (tm) 3600 Software (C3660-IS-M), Version 12.2(19)
System image file is "flash:c3660-is-mz.122-19.bin"
3660 Chassis type: ENTERPRISE we are getting above said trap responses..
from the following router models we are not getting
'dialCtlPeerCallInformation and DialCtilPeerCallSetup" traps...
C1700 Software (C1700-IPVOICE-M), Version 12.3(7)XR3, RELEASE SOFTWARE (fc2)
System image file is "flash:c1700-ipvoice-mz.123-7.XR3.bin"
IOS (tm) 3600 Software (C3640-IK8S-M), Version 12.2(19)System image file is "flash:c3640-ik8s-mz.122-19.bin"
IOS (tm) C2600 Software (C2600-IO3S56I-M), Version 12.1(3)T, System image file is "flash:c2600-io3s56i-mz.121-3.T.bin"
IOS (tm) C2600 Software (C2600-IO3S56I-M), Version 12.1(3)T,System image file is "flash:c2600-io3s56i-mz.121-3.T.bin" cisco 2610 (MPC860) processor
IOS (tm) C1700 Software (C1700-SV3Y-M), Version 12.2(8)T,System image file is "flash:c1700-sv3y-mz.122-8.T.bin" cisco 1750 (MPC860T) processor
why this happens so???according to the cisco documentation all these routers are meeting the IOS requirements!!!!!!!
is this any bug in cvm/client router ios???
anybody please help in these things...??
thanks in advance
regards..
shiju
[email protected]

Do you mean decline button before picking up the call?

IOS VERSION FOR MPLS

Hi! i'm trying to do a lab at my university implementing MPLS. I have routers cisco 2610 series. This is my configuration:
Cisco2600-2(config-if)# ip route-cache cef
Cisco2600-2(config-if)# mpls label protocol ldp
Cisco2600-2(config-if)#mpls ip
My problem is that i can't use te "set mpls experimental topmost " command at the policy-map. My options are:
Cisco2600-2(config-pmap-c)#?
QoS policy-map class configuration commands:
bandwidth Bandwidth
compression Activate Compression
drop Drop all packets
exit Exit from QoS class action configuration mode
no Negate or set default values of a command
police Police
priority Strict Scheduling Priority for this Class
queue-limit Queue Max Threshold for Tail Drop
random-detect Enable Random Early Detection as drop policy
service-policy Configure QoS Service Policy
shape Traffic Shaping
My version of the IOS is:
IOS (tm) C2600 Software (C2600-TELCO-M), Version 12.3(15b), RELEASE SOFTWARE (fc1)
wich version do i need to run this command and configurations?? Any information will help. Thank you very much. Best regards!!

It is my understanding that you don't have that capability in those images (or platform). I didn't find the feature in the feature set of the 2600 platform. The feature you are looking for is: "MPLS Quality of Service (QoS) Enhancements"
From the feature set definition:
- MPLS quality of service enhancements allow service providers to classify packets according to their type, input interface, and other factors by setting (marking) each packet within the MPLS experimental field without changing the IP precedence/DSCP field. For example, service providers can classify packets with or without considering the rate of the packets that PE1 receives. If the rate is a consideration, the service provider marks in-rate packets differently from out-of-rate packets.
HTH,
-W

"frags delayed" counter incrementing for Voice PVC

Hi,
We are using VoFR between two Cisco 2610 using FXO\FXS Cards. It is a point-point link with two PVCs, one for Voice and one for Data.
I have implemented Traffic-Shaping and FRF. However when i do a "show frame pvc " command, i can see "frags delayed"counter incrementing for the Voice PVC, indiciating delay in sending packets and thus compromising Voice Quality.
1. Is it normal to have this counter increasing ? What is the acceptable percentage i.e "frags delayed \ total frags" ?
2. Is there anything i can do ? Would PVC Priority Queuing help ?
I need to be sure if PVC Priority is the solution, as we would have to do a Flash Upgrade to install the new software with this feature.
++++++++++++++++++++++++++
show frame pvc 103
PVC Statistics for interface Serial0/0 (Frame Relay DTE)
DLCI = 103, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial0/0.3
input pkts 373951 output pkts 374604 in bytes 11542352
out bytes 12245392 dropped pkts 0 in FECN pkts 0
in BECN pkts 0 out FECN pkts 0 out BECN pkts 0
in DE pkts 0 out DE pkts 0
out bcast pkts 5474 out bcast bytes 1571038
pvc create time 11w3d, last time pvc status changed 04:06:31
Service type VoFR-cisco
Voice Queueing Stats: 0/100/0 (size/max/dropped)
Current fair queue configuration:
Discard Dynamic Reserved
threshold queue count queue count
64 16 2
Output queue size 0/max total 600/drops 0
configured voice bandwidth 30000, used voice bandwidth 0
fragment type VoFR-cisco fragment size 320
cir 32000 bc 320 be 0 limit 40 interval 10
mincir 32000 byte increment 40 BECN response no
frags 374604 bytes 12261814 frags delayed 6501 bytes delayed 1609296
shaping inactive
traffic shaping drops 0
+++++++++++++++++++++++++++++++++++

The following links explains the delay in voice traffic and gow to do traffic policing
VoIP over Frame Relay with QoS (Fragmentation, Traffic Shaping, LLQ / IP RTP Priority)
http://www.cisco.com/warp/public/788/voice-qos/voip-ov-fr-qos.html#15
Troubleshooting Output Drops with Priority Queueing
http://www.cisco.com/warp/public/105/priorityqueuedrops.html
Understanding Delay in Packet Voice Networks
http://www.cisco.com/warp/public/788/voip/delay-details.html
Voice QoS: ToS-CoS Mapping Via LLQ
http://www.cisco.com/warp/public/788/voice-qos/tos-cos.html
Frame Relay Traffic Shaping for VoIP and VoFR
http://www.cisco.com/warp/public/788/voip/fr_traffic.html

I do 'router isis' but I get 'protocol not in this image'

C2610, IOS 12.3.
I've searched this on forums but I couldn't find the answer:
I attempt to do 'router isis' but IOS returns 'protocol not in this image'. How can I solve this ? I would like to work on ISIS redistribution labs against EIGRP, OSPF, etc.

Thanks for info. hmmm... I need to search it more, but so far it seems my image can't do ISIS...
Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-I-M), Version 12.3(12b), RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2005 by cisco Systems, Inc.
Compiled Thu 31-Mar-05 19:08 by jfeldhou
Image text-base: 0x80008098, data-base: 0x80CCAA68
ROM: System Bootstrap, Version 11.3(2)XA4, RELEASE SOFTWARE (fc1)
ROM: C2600 Software (C2600-I-M), Version 12.3(12b), RELEASE SOFTWARE (fc2)
RouterC uptime is 8 hours, 16 minutes
System returned to ROM by power-on
System image file is "flash:c2600-i-mz.123-12b.bin"
cisco 2610 (MPC860) processor (revision 0x203) with 28672K/4096K bytes of memory
Processor board ID JAD05390K1C (3082946085)
M860 processor: part number 0, mask 49
Bridging software.
X.25 software, Version 3.0.0.
1 Ethernet/IEEE 802.3 interface(s)
2 Serial network interface(s)
32K bytes of non-volatile configuration memory.
--More--

NM-HDA-4FXS in Cisco 2610

Similar Messages

Maybe you are looking for