NM-HDV DSP resource sharing

I have a NM-HDV module with two PVDM-16 modules and a VWIC-1MFT installed in a 2811. I have a VIC2-2FXO card that I need to install into one of the HWIC slots. Is there any way that I can share the DSP resources from the NM-HDV for the new FXO card or do I have to install new PVDM2 dsp modules in the 2811?

Can we put PVDM2-64 on NM-HDV network module ?
Because we are using NM-HDV module with PVDM12, we want to add PVDM2-64 on this module. will it possible?
Regards,

Similar Messages

DSP Resource for VIC3-4FXS/DID on NM-HDV2

Hi,
If only PVDM3 is installed on the C3945 motherboard (Slot 0), and I have VIC3-4FXS/DID inserted in the NM-HDV2 and but without PVDM2 installed in the NM-HDV2, can I still enable the FXS port?
Do I need to have this command to enable dsp sharing with the NM-HDV2?
voice-card 1
dsp tdm pooling
Also, should the FXS ports appear in the "show voice port summary"?
Thank you.

Hi,
just refer this
http://www.cisco.com/c/en/us/products/interfaces-modules/2800-3800-high-density-packet-voice-digital-signal-processor/index.html
Are the PVDM3 modules supported in a NM-HDV2?
A. No. You cannot install PVDM3 modules directly on the PVDM slots of an NM-HDV2, only the PVDM2s are
supported by the NM-HDV2. However, an NM-HDV2 that has no PVDMs installed at all can share PVDM3 DSP
resources from the router motherboard PVDM slots across the chassis backplane.
Q. Do the PVDM2 modules work with the Cisco 2900 and 3900 Series platforms?
A. Yes. You can install PVDM2 modules on the motherboard PVDM slots using special adaptor cards (PVDM2-
ADPTR). You can also insert an NM-HDV2 module with PVDM2 modules into the service-module slot of the
Cisco 2900 and 3900 Series platforms using the network-to-server module adaptor card (SM-NM-ADPTR).
regds,
aman

NM-HDV DSP Problems...

Dear Friends
I have a Cisco 3640 with NM-HDV-2E1-60 module with VWIC-2MFT-E1.
The ios image is c3640-js-mz.123-19.bin and version is 12.3
I have a strange problem with the NM-HDV module.
I make the calls then these calls connect and after 2-3 seconds they drop, and the module doesn't free the channel, the channel stays busy...
All the lights on the nm-hdv dsp light up green.
I've tried to test the dsp's issuing the test dsp 0 command and then querying the dsp resource and status and it shows up the following
Dsp firmware version: 4.1.41
Maximum dsp count: 15
On board dsp count: 15
Jukebox available
Total dsp channels available 60
Total dsp channels allocated 60
Total dsp free channels 0
Querying dsp status......
It doesn't show the dsp status...
test dsp 1 (2, 3) commands say that Card 1 (2, 3) is not present.
How can I be 100% that the problem is because of the DSP's (if it is like that)
I'm saying this because I can buy new DSP's and change them, but I need to be 100% sure...
Any reply is appreciated!

Thanks for your reply.
I've done some tests and here's the result.
c3640_gw2# show dialplan number 12345678911
Macro Exp.: 12345678911
VoiceEncapPeer1
peer type = voice, information type = voice,
description = `',
tag = 1, destination-pattern = `111+',
answer-address = `', preference=0,
CLID Restriction = None
CLID Network Number = `'
CLID Second Number sent
CLID Override RDNIS = disabled,
source carrier-id = `', target carrier-id = `',
source trunk-group-label = `', target trunk-group-label = `',
numbering Type = `unknown'
group = 1, Admin state is up, Operation state is up,
Outbound state is up,
incoming called-number = `', connections/maximum = 1/unlimited,
DTMF Relay = disabled,
huntstop = disabled,
in bound application associated: 'DEFAULT'
out bound application associated: ''
dnis-map =
permission :both
incoming COR list:maximum capability
outgoing COR list:minimum requirement
Translation profile (Incoming):
Translation profile (Outgoing):
incoming call blocking:
translation-profile = `'
disconnect-cause = `no-service'
advertise 0x40 capacity_update_timer 25 addrFamily 4 oldAddrFamily 4
type = pots, prefix = `11',
forward-digits default
session-target = `', voice-port = `0/0:0',
direct-inward-dial = disabled,
digit_strip = enabled,
register E.164 number with GK = TRUE
fax rate = system, payload size = 20 bytes
supported-language = ''
Time elapsed since last clearing of voice call statistics never
Connect Time = 1876, Charged Units = 0,
Successful Calls = 12, Failed Calls = 5, Incomplete Calls = 0
Accepted Calls = 0, Refused Calls = 0,
Last Disconnect Cause is "AC ",
Last Disconnect Text is "dsp error (172)",
Last Setup Time = 241131.
Matched: 12345678911 Digits: 3
Target:
So it seems that the problem is really in DSPs.....

Cross-origin resource sharing (CORS) does not work in Firefox 13.0.1 or 6.0.2

I have a simple Java HttpServlet and a simple JSP page. They are both served by a WebSphere Application Server at port 80 on my local host. I have created a TCP/IP Monitor at port 8081 in
Eclipse IDE so as to create a second origin. The protocol output further down comes from this monitor. This should work equally well on a simple Tomcat server.
When I perform the cross-origin resource sharing test, I see that all of the correct TCP data is exchanged between Firefox and the web server (i.e. HTTP OPTIONS and its response followed by an HTTP POST and its response) but the data in the body of the POST response is never passed to the XMLHttpRequest javascript object's responseText or responseXML variables and I get a status equal to 0. If I click the button while pressing the keyboard control key then the test will work as it will not be performed as a cross-origin request.
Here are all of the files used in this test:
Servlet Cors.java
<pre><nowiki>--------------------------------------------------------------------------------------
package example.cors;
import java.io.IOException;
import java.util.Enumeration;
import javax.servlet.Servlet;
import javax.servlet.ServletConfig;
import javax.servlet.ServletException;
import javax.servlet.http.HttpServlet;
import javax.servlet.http.HttpServletRequest;
import javax.servlet.http.HttpServletResponse;
* Servlet implementation class Cors
public class Cors extends HttpServlet {
private static final long serialVersionUID = 1L;
private static final String APPLICATION_XML_VALUE = "application/xml";
* @see HttpServlet#doGet(HttpServletRequest request, HttpServletResponse response)
protected void doGet(HttpServletRequest request, HttpServletResponse response) throws ServletException, IOException {
doPost(request, response); // do the same as on the post
* @see HttpServlet#doPost(HttpServletRequest request, HttpServletResponse response)
protected void doPost(HttpServletRequest request, HttpServletResponse response) throws ServletException, IOException {
response.setBufferSize(1024);
response.setContentType(APPLICATION_XML_VALUE);
response.setStatus(HttpServletResponse.SC_OK);
String xml="<?xml version=\"1.0\"?>\n<hello>This is a wrapped message</hello>";
response.setContentLength(xml.length());
response.getWriter().append(xml);
response.getWriter().close();
* @see HttpServlet#doOptions(HttpServletRequest, HttpServletResponse)
@SuppressWarnings("unchecked")
protected void doOptions(HttpServletRequest request, HttpServletResponse response) throws ServletException, IOException {
Enumeration<String> headers=request.getHeaders("Origin");
StringBuffer sb=new StringBuffer();
while (headers.hasMoreElements()) {
String o=headers.nextElement();
if (sb.length()!=0) sb.append(", ");
System.err.println("Origin= "+o);
sb.append(o);
response.addHeader("Access-Control-Allow-Origin", sb.toString());
response.addHeader("Access-Control-Allow-Methods","POST, GET, OPTIONS");
sb=new StringBuffer();
headers=request.getHeaders("Access-Control-Request-Headers");
while (headers.hasMoreElements()) {
String o=headers.nextElement();
if (sb.length()!=0) sb.append(", ");
System.err.println("Access-Control-Request-Headers= "+o);
sb.append(o);
response.addHeader("Access-Control-Allow-Headers", sb.toString().toUpperCase());
response.addHeader("Access-Control-Max-Age", Integer.toString(60*60)); // 1 hour
response.addHeader("Content-Type","text/plain");
response.addHeader("Allow", "GET, HEAD, POST, PUT, DELETE, TRACE, OPTIONS");
response.getWriter().print("");
And a simple JSP page test.jsp:
<%@ page language="java" contentType="text/html; charset=ISO-8859-1"
pageEncoding="ISO-8859-1"%>
<!DOCTYPE html PUBLIC "-//W3C//DTD HTML 4.01 Transitional//EN" "http://www.w3.org/TR/html4/loose.dtd">
<html>
<head>
<%
String url ="http://localhost:8081/cors/ping";
String url_ctrl="http://localhost/cors/ping";
%>
<meta http-equiv="Content-Type" content="text/html; charset=ISO-8859-1">
<title>Test CORS</title>
<script type="text/javascript">
var invocation;
var method='POST';
var body = "<?xml version=\"1.0\" encoding=\"UTF-8\" standalone=\"yes\"?><hello>Today</hello>";
var buttontest2_label="Direct AJAX call";
function callOtherDomain(event){
invocation = new XMLHttpRequest();
if(invocation) {
var resultNode = document.getElementById("buttonResultNode");
var resultMessage = document.getElementById("buttonMessageNode");
resultNode.innerHTML = "";
document.getElementById("buttontest2").value="Waiting response...";
var url
if (event.ctrlKey) url="<%=url_ctrl%>";
else url="<%=url%>";
resultMessage.innerHTML = "Sending "+method+" to URL: "+url;
invocation.open(method, url, true);
// invocation.withCredentials = "true";
invocation.setRequestHeader('X-PINGOTHER', 'pingpong');
invocation.setRequestHeader('Content-Type', 'application/xml');
invocation.setRequestHeader('X-Requested-With', 'XMLHttpRequest');
invocation.onerror = function(errorObject) {
display_progress(resultMessage, "***** error occured=" +errorObject);
invocation.onreadystatechange = function() {
display_progress(resultMessage, "onreadystatechange="+invocation.readyState+", status="+invocation.status+", statusText="+invocation.statusText);
if(invocation.readyState == 4){
document.getElementById("buttontest2").value=buttontest2_label;
display_progress(resultMessage, "responseText="+invocation.responseText);
resultNode.innerHTML = "Response from web service='"+invocation.responseText+"'";
invocation.send(body);
function display_progress(node, message) {
node.innerHTML = node.innerHTML + "<br>" + message;
</script>
</head>
<body>
<p>The button will create a cross site request (Use the control key to disable this, i.e. no cross site request)</p>
<p><input type="button" id="buttontest2" onclick="callOtherDomain(event)" name="buttontest2" value="Waiting for page load..."></p>
<p id="buttonMessageNode"></p>
<p id="buttonResultNode"></p>
<script type="text/javascript">
document.getElementById("buttontest2").value=buttontest2_label;
</script>
</body>
</html>
When I click on the Direct AJAX call button, I get the following output on my page:
The button will create a cross site request (Use the control key to disable this, i.e. no cross site request)
Sending POST to URL: http://localhost:8081/cors/ping
onreadystatechange=2, status=0, statusText=
onreadystatechange=4, status=0, statusText=
responseText=
***** error occured=[object ProgressEvent]
Response from web service=''
Here is the HTTP traffic produced:
HTTP REQUEST
OPTIONS /cors/ping HTTP/1.1
Host: localhost:8081
User-Agent: Mozilla/5.0 (Windows NT 5.1; rv:13.0) Gecko/20100101 Firefox/13.0.1
Accept: text/html,application/xhtml+xml,application/xml;q=0.9,*/*;q=0.8
Accept-Language: en-us,en;q=0.5
Accept-Encoding: gzip, deflate
Connection: keep-alive
Origin: http://localhost
Access-Control-Request-Method: POST
Access-Control-Request-Headers: content-type,x-pingother,x-requested-with
Pragma: no-cache
Cache-Control: no-cache
POST /cors/ping HTTP/1.1
Host: localhost:8081
User-Agent: Mozilla/5.0 (Windows NT 5.1; rv:13.0) Gecko/20100101 Firefox/13.0.1
Accept: text/html,application/xhtml+xml,application/xml;q=0.9,*/*;q=0.8
Accept-Language: en-us,en;q=0.5
Accept-Encoding: gzip, deflate
Connection: keep-alive
X-PINGOTHER: pingpong
Content-Type: application/xml; charset=UTF-8
X-Requested-With: XMLHttpRequest
Referer: http://localhost/cors/client/test.jsp
Content-Length: 75
Origin: http://localhost
Pragma: no-cache
Cache-Control: no-cache
<?xml version="1.0" encoding="UTF-8" standalone="yes"?><hello>Today</hello>
HTTP RESPONSE
HTTP/1.1 200 OK
Access-Control-Allow-Origin: http://localhost
Access-Control-Allow-Methods: POST, GET, OPTIONS
Access-Control-Allow-Headers: CONTENT-TYPE,X-PINGOTHER,X-REQUESTED-WITH
Access-Control-Max-Age: 3600
Content-Type: text/plain;charset=ISO-8859-1
Allow: GET, HEAD, POST, PUT, DELETE, TRACE, OPTIONS
Content-Language: en-CA
Content-Length: 0
Date: Wed, 11 Jul 2012 17:50:10 GMT
Server: WebSphere Application Server/7.0
HTTP/1.1 200 OK
Content-Type: application/xml
Content-Length: 62
Content-Language: en-CA
Date: Wed, 11 Jul 2012 17:50:10 GMT
Server: WebSphere Application Server/7.0
<?xml version="1.0"?>
<hello>This is a wrapped message</hello>
--------------------------------------------------------------------------------------</nowiki></pre>

No errors in error console. No effect using *. I tried using the dns name of my localhost both in the Firefox URL and in the javascript and I get exactly the same. I have spent a huge amount of time looking into this issue.
One thing I noticed is that if I use the examples on the internet (http://arunranga.com/examples/access-control/preflightInvocation.html or http://saltybeagle.com/cors/) they work in the same browser. These examples however, are accessed through HTTP proxies.
I am wondering if the issue has to do with using the same hostname just with different ports.

Proper amount of DSP resources in router?

Let's say we have a small site with 25 IP phones, 4 analog devices using a FXS module in the router and an ISDN PRI circuit using a T1 module in the router. I assume a PVDM3 module with 64 DSPs would be more than enough to handle that site? Does the FXS module have its own DSP resources and we don't need to figure those in? I figure the ISDN PRI would use up to 23 DSP resources and then what's left out of the 64 on that PVDM3 could be used for conferencing, media termination point and so on. Am I thinking about this correctly? Sound reasonable (64 DSPs for a site like that)?

I didn't know there was one....but I just found it. Thanks

Running data at different rates within a SCTL for resource sharing

I have a design that contains several single cycle timed loops (SCTL):
(40MHz SCTL) -> (20MHz SCTL) -> (40MHz SCTL) -> (10MHz SCTL)
The first 2 SCTLs are decimation filters so that the data coming out of the 20MHz SCTL is
at a 10MHz sampling rate. The 2ns 40MHz SCTL is filter that is 4X resource
shared so that I can use the available dsp48E slices. I'm using target-scoped FIFOs to
pass the data between the loops. In simulation, I have the timeout set to -1 so that it reads
from the FIFO whenever there is data available.
When I run the simulation, I expect/want to see my control counter running 4 times faster
than my incoming data. I thought that since the data was written into the target-scoped
FIFO at a 10MHz rate and the control counter is in the 40MHz SCTL, I would see the
behavior I wanted:
    X a     X    b    X      c     X     d     X <- data from FIFO
X0X1X2X3X0X1X2X3X0X1X2X3X0X1X2X3X <- modulo-3 counter
Instead I see the data and counter essentially running at the same rate:
    X1X2X3X4X5X6X7X8X9XaXbXcXdXeXf X0X    <-data from FIFO
    X0X1X2X3X0X1X2X3X0X1X2X3X0X1X2X3X    <-modulo-3 counter
Also the iteration counter for the SCTL runs at the same rate which seems to indicate that the
loop only executes when data is pulled from the FIFO. I was expecting the iteration counter
to be at 3 before the second sample was read from the FIFO and at 7 before the third sample
was read from the FIFO. I'm guessing that the simulator is event driven.
I have a couple of questions:
1. How can I get the behavior I'm looking for?
2. If not, can I expect the behavior I want if I run this on the hardware?

update:
NI support suggested using the FIFO timeout signal to determine when the data is valid
coming out of the FIFO. I was using a -1 on the FIFO read to read only when a sample
was available. NI support said to use a 0 and then gate the data based on the timeout
signal. The behavior of the design changed, but still did not give me the timing I was
expecting. Instead of seeing my counter update on every new sample, I see the SCTL
"free running" It's difficult to determine if the counter is behaving properly, but I do see it
running faster. The problem is that the SCTL seems to be running much faster was well.
Using the -1 on the FIFO read I would see > 262K samples written out for every 1000 in.
Using the 0 on the FIFO read and gating the data based on the timeout signal, I see
>60K samples for every 1000 read in. I'm expecting 250 samples out for every 1000 in.
Can someone tell me what controls the behavior (in terms of execution0 of the SCTL? It
seems like it is event driven, but I need the design to be clock or cycle driven for both
simulation and execution of the hardware.
Regards,

How to enable resource sharing with complex AEBS setup

I have a complex AEBS + Netgear network configuration that I am trying to enable resource sharing on. The Netgear router is necessary because it provides excellent per-user parental controls and content filtering that the AEBS lacks. The setup is operational (network connectivity works as expected), but I cannot figure out how to enable cross-network resource visibility and sharing.
Here is the network configuration:
|Vz Fios PPoEE |
|
v
|___
|AEBS|
| __Mac Mini (wireless)
| __AppleTV (wireless)
| __Wii (wireless)
| __MBPC2Duo (wireless)
| __WinXp PC1 (wired)
|
v
|______
|Netgear|
| __WinXP PC2/Printer (wired)
| __WinXp PC3 (wired)
| __iBook (wireless)
| __Vista Laptop1 (wireless)
| __Vista Laptop2 (wireless)
The Mini, AppleTV, Wii and MBPC2Duo all connect wirelessly with the AEBS. The Netgear router is wired to the AEBS. This in turn has 2 wired clients and three wireless clients as illustrated.
The Netgear router receives an IP address assignment from the AEBS (in the 10.0.1.x range) via DHCP and in turn assigns IP addresses (in the 192.168.1.x range) to attached clients via DHCP
The setup is operational and operates flawlessly --network-wise. However, I now need to enable resource sharing as follows:
1) Setup the Mini as the media hub, configured to allow:
a. storage of all iTunes, iPhoto, iMovie and garage band content to an attached external hard drive,
b. sharing of content on the Mini with iTunes on each computer (Macs and Pcs) and the AppleTV
2) Share the printer attached to Windows XP PC2 with all computers (Macs and PCs)
Questions:
1. Is this possible with this network configuration?
2. If so, how would I configure the relevant elements?
3. Is it better to attach the external media storage to the AEBS vs attaching it to the Mini?
Thanks!

Thanks Tesserax. After some digging I was able to find bridge mode config instructions for the Netgear router.
Follow-up question:
Given my desire to centralize media access via the Mac Mini, what is the best way to set up my media storage device (320G HD)?
I see the following options:
A. NAS device via USB 2.0 connection to the AEBS, or
B. Supplemental hard drive on the Mac Mini via USB 2.0 or Firewire.
Thoughts/suggestions?
Thanks!

DSP resources ISDN Busy Message

Hi,
we are using two 1760 with VWIC-1MFT-E1 to connect to PBXs via WAN.
We have not enough DSPs to support all channels of the E1.
Is there any possibility to transfer the no dsp resources available message to an ISDN Busy event, so that the PBX which is gerating the call will get an ISDN message and not a SID tone?
many thanks in advance
August

I don't think we can do this. One workaround may be to only configure the channels that the DSPs support on the 1760.
Hope this helps.

Modifying DSP resource Allocation on the AS5300

It seems I may have some faulty DSP banks on an AS5300 but aren't sure how to 'juggle' the resources around to identify where the faulty channels lie. Could anyone point me in the right direction??
Many thanks

Many thanks for that.
I'm unsure whether it is a DSP problem...basically whats happening is that the DTMF tones are going astray when the AS5300 is busy, I'm unsure how to edit the DTMF settings on the box. So there's two things, firstly how would I be able to tell if it's a DSP resource that is faulty?? And also, where in the config can I manipulate the DTMF transport methods??
Many thanks again

Project 2010 Resource Sharing

I currently have a Project set up that includes multiple sub-projects. I want to use one resource pool for all the sub-projects but I am having trouble getting this to work. how can this be achieved?

N.Isaac,
can you be a little more specicifc as to what is the method you are employing and the trouble you are experiencing?
In order to use one resource pool, you need to set up a Shared Resource Pool, and use the same pool across all sub-projects.
here is some guidance on how to do it: https://support.office.microsoft.com/en-us/article/Create-and-share-a-resource-pool-64a2416e-b811-4ddf-b039-e0347e233581?CorrelationId=552b031b-6431-4a81-9d7c-c38b3735fae1&ui=en-US&rs=en-US&ad=US
Cheers,
Prasanna Adavi, Project MVP
Blog:
Podcast:
Twitter:
LinkedIn:

BOM Resources Sharing across organization

Frnds
My Client is in 12.1.3 , Is there any set up in Oracle manufacturing (BOM, WIP, INV) , which can help in sharing Resources (machine. Human) across Organization
with required accounting too ??
e.g
Inventory organization – INV1 and INV2
now if any discrete job in INV1 or INV2 needs any resource then it should be issued from common resource organization. Also that resource accounting will be done in that specific balancing segment other than balancing segments specific to inventory or WIP valuation accounting
Any help would be a great help
Regards
Abhi

What is the version of apps you are using? Fact: in R12, for average costing organizations, if you refer original order line to RMA the cost of return is same as original order line. also there are some more features that relate to the revenue and COGS recognition.
That apart we may have these options:
1. Make branch warehouse organization as standard cost. Use the cost as of the start of the year. Now when you return the goods into this org you always cost at standard. At end of the year, you update your standard cost to be equal to the average cost of new item at the time of the year. Depending on whether your average cost is higher or lower you will have increase or decrease in inventory value (hence other account).
2.Use cost hooks creatively (have to test this): Cost manager always checks whether cost hooks are used or not (there are two types one for cost and one for accounting). In the accounting one, if it returns -1 means hook is not used (I guess). So have a piece of code in there that inserts record into mtl_transactions_interface of branch organization. The transaction type you use here is average cost update (even if you have no quantity you can do this). Call the online transaction manager right after that to make it completely online and still return -1. I will confirm after testing this.
3. If 99% of the times the machines are are new, can you make Branch as Subinventory in that A Organization rather than different org?
4. I see a distant possibility of using order line workflow. Is this branch warehouse only for returns? If that is the case do you refer the original line Id to the RMAs? But the logic remains the same : Using transaction interface for the average cost update.
5.Your idea is also a great one. Why don't you automate that same thing in the order line workflow. Under certain conditions automatically perform inter org transfer to branch as soon you receive into Org A using transaction interface.
Thanks
Nagamohan

DSP resources? - How to for dummies please.

Can you help me undestanting how to uses the calculator?
The first issue I found is how to make it work with PVDM3 or VWIC3, then what do I need to write in each part.
Finally how to interpret the output.
I want to know if whit the below information I can support two E1 (32 channels each)
R1#show inventory
NAME: "CISCO2921/K9", DESCR: "CISCO2921/K9 chassis, Hw Serial#: XXXXXXXXXXX, Hw Revision: 1.0"
PID: CISCO2921/K9      , VID: V08 , SN: XXXXXXXXXXX
NAME: "VWIC3-2MFT-T1/E1 - 2-Port RJ-48 Multiflex Trunk - T1/E1 on Slot 0 SubSlot 0", DESCR: "VWIC3-2MFT-T1/E1 - 2-Port RJ-48 Multiflex Trunk - T1/E1"
PID: VWIC3-2MFT-T1/E1 , VID: V01 , SN: FOC17045FDX
NAME: "PVDM3 DSP DIMM with 32 Channels on Slot 0 SubSlot 4", DESCR: "PVDM3 DSP DIMM with 32 Channels"
PID: PVDM3-32          , VID: V01 , SN: FOC165248EF
NAME: "PVDM3 DSP DIMM with 32 Channels on Slot 0 SubSlot 5", DESCR: "PVDM3 DSP DIMM with 32 Channels"
PID: PVDM3-32          , VID: V01 , SN: FOC17080NSH
NAME: "C2921/C2951 AC Power Supply", DESCR: "C2921/C2951 AC Power Supply"
PID: PWR-2921-51-AC    , VID: V03 , SN: QCS1650H162
I read the help guide, but I dont quite understand this.

VWIC3-2MFT-T1/E1 is the card that will allow you to connect 2 seperate E1 circuits to it.
PVDM3-32 will allow conversion from TDM (E1) to voip, depending on which codec you are going to use each call will either use 1 PVDM channel (low/medium complexity i.e. G711), or 2 channels (high complexity, i.e. G729R8).
HTH,
Chris

Resource sharing

What is meant by Pool takes Precedence and Sharer takes precedence. If Please explain me with an example.
Regards,
Shiv
Sivakumar.G (Project Management Consultant)

I personally would not recommend using Sharer tasks precedence as it can lead to a battle among Project Managers. Taking the same example above: Mary is a resource assigned to multiple projects and multiple assignments. She talks to Alan (PM)
and tells him that she is going to take the first week in March off. Alan looks at his schedule and Mary is not assigned to any tasks that week. He says okay and updates Mary's working calendar with the week of leave.
Brian opens his project and see that a number of his tasks have been moved. He spends quite a bit of time and finally figures out that Mary's calendar has been changed and the assignments for Mary in his project have been moved. He goes to Mary's
calendar and removes her week of leave. His schedule is now fine. Two days later, Alan notices that Mary's non-working time is gone. Thinking he has done something incorrectly, he puts the non-working time back.
I think you can guess what happens next time Brian opens his project file.

OSB: Resource sharing among multiple configuration project

Hi,
Is there any way to share the resources among multiple configuration project in OSB 11g? Please provide any solution for this.
Regards,
Rakesh Ranjan

Sharing resource across projects in OSB11g
Regards,
Anuj

Design - Domain Resource Sharing and Privacy

Our organization would like to provide an environment where shared core services are housed in a root domain with several client domains having access to these core services.
We would also like to provide email, file, and other services within separate client domains, but maintain privacy of user lists, email address lists, etc. between these client domains.
Client2 users should not be able to see the users’ names, accounts, etc. or enumerate address lists, attributes, or groups that pertain to Client1 domain (and vice versa).
In a nutshell, we’d like to shield all visibility of other client domains between each other but still be able to manage this as one directory.
Is one forest possible (figure 1), or are we relegated to having separate forests (figure 2) with external trusts linked to the core domain?

Hi Doug,
Since a two-way transitive trust will be created if we set up a new domain in one forest, as you mentioned, you will need to deny many permissions that users already have in the forest cautiously and thoroughly, and it will not
be a very simple task, because these domains aren’t supposed to trust each other.
Therefore, I agree with Paul, you need to set up multiple forests, and non-transitive trust, which will make things much easier.
Best Regards,
Amy

NM-HDV DSP resource sharing

Similar Messages

Maybe you are looking for