NM-HDV2-2T1/E1 with VWIC-2MFT-G703

The maximum ports I can configured is 2 instead of 4 when the above is installed in Cisco 2821 router.
VWIC-2MFT-G703 = 2 E1 port
NM-HDV2-2T1/E1 = 2 E1 port
Is this a limition?
With Regards
Chin Lam

vwic-1mft-e1 is a single port e1 WIC. This can be used in a regular hwic slot of a 2800/3800. This card requires that you install PVDM2 chips (DSPs) on the motherboard of the 2800 (if the card is installed on a hwic slot).
With NM-HDV2-2T1/E1, which is a network module has higher density to install up to 4 PVDM2 chips on the network module and has a optional vic slot on the network module. This version of NM-HDV2 also has 2 on board t1/e1 ports. These two onboard ports can be configured as t1 or e1 at the same time. Upto 4 t1/e1 ports may be installed at any time on an NM-HDV2 as long as you populate enough DSPs.
I would recommend you to determine,
a. what type of connection you need to PSTN (t1/e1) ?
b. How many such connections you need ?
If your requirement is < 8, i would recommend not using NM-HDV2 and just use the regular hwic slot on the router, with a vwic-1mft-e1 or similar.
HTH
Sankar
PS: please remember to rate posts!

Similar Messages

  • Clocking Issues with VWICs

    We connected a 3825 to a Nortel PBX today and had some weird clocking issues. We're using VWIC-2MFT-T1 modules and I think I need to learn more about how clocking works with these things. The PBX didn't seem to like it when the router provided clock. The engineer working with us told us that he thinks the clock on the router is not stable enough to provide clocking.
    Have any of you had any issues using a router to provide clocking to a PBX? It seems like it shouldn't be a problem but we kept experiencing slips on the Nortel side if the router was providing clocking.
    This creates a problem for us. We will be connecting one port to a frame relay data circuit and that port must be set to "clock source line". If the router can't provide clock to the PBX then that port also must be set to "clock source line".
    I ran across a tech note that says the following:
    "When both ports on a VWIC-2MFT-T1, VWIC-2MFT-E1, VWIC-2MFT-G703, or VWIC-2MFT-E1-DI interface card are configured as clock source line, then they must be set to the same clock source. If they are not set to the same clock source, timing slips can occur. Each port on the VWIC2-2MFT-T1/E1 and VWIC2-2MFT-G703 interface cards can be set to independent clock sources for data applications."
    Are we going to run into problems since we don't have the VWIC2 modules?
    I don't understand the way clocking works with these modules anyway. With only one port connected to the PBX we were seeing slips even with the router was set to "line". We fixed that by using the "network-clock-select 1 T1 0/0/0" command. I don't know what that command actually does but it stabilized the clock and eliminated the slips. Weird. I need to go do some research on this issue because we need to get it figured out and settled soon.
    Any thoughts?
    Thanks!
    John

    The 2800 and 3800 routers have internal tdm buses that can be used to tdm switch between any ports on the box. You use 'network-clock-select' to pick the clocking source for the internal tdm bus. This clock source is then used for every interface that is identified via the 'network-clock-participate' command. The best you can do in your case is to clock off the frame relay network and see if you get slips on the T1 to the nortel, or clock off the nortel and check for slips to FR. Make sure the nortel is set up correctly to either take clocking from the T1 or provide clocking on the T1 - you may not have a choice there depending on protocol used. Best practice (and what you may end up needing to do) is to separate the T1s onto different VWICs so that clocking can be independent. Even with a VWIC2 you only get 1 clock source if using voice (with data can run ports independently).
    The internal clock on the router, like the internal clock on the PBX, should only be used for fallback as they aren't nearly as accurate as what is used in the cloud. For this reason you create a synchronization plan that cascades the clock from the cloud. In your case the nortel would clock off the PSTN (I'm sure already being done) and cascades clocking to the 3825. When you get more PSTN trunking into the IP side of things you would want to swap - have the 3825 clock off a PSTN T1 and then cascade clocking to the Nortel.
    hth,
    Don

  • VWIC2-2MFT-G703, cRTP and Multilink

    Hello,
    I wish to know if it is possible aggregate 2 E1/G703 data link in order to increase bandwidth up to 4 Mbps (2x 2 Mbps) with the card VWIC2-2MFT-G703, by using ppp encapsulation with the multilink feature.
    I have read several documents and according to them, I conclude that this setup is possible but I can not test it.
    Does somebody can confirm that such setup is possible ?
    With the same idea, with 2 cards (VWIC2-2MFT-G703) is it possible to get 8 Mbps (2x 2 Mbps per card) ?
    I will use 18xx or 29xx routers.
    Next, with this setup, I whish to enable cRTP.
    I suppose that I can enable this feature on the Multilink interface with something like that:
    ===
    interface Mutlilink <group-number>
    ip address <address> <mask>
    encapsulation ppp
    ppp multilink
    ip rtp header-compression ...
    ===
    Does somebody can confirm that cRTP is available with such setup (multilink with VWIC2-2MFT-G703 card) ?
    Thanks for your Help.
    GP.

    Hi GP,
    Thank you for your question.  However, the Small Business Support Community is limited to Cisco Small Business Products.
    Your question below may relate to a Cisco Classic Product which our community would not be able to help you with.
    The best area for you to post your question would be at the Cisco NetPro forums: https://supportforums.cisco.com/index.jspa
    Best regards,
    Cindy
    Cindy Toy
    Small Business Community Manager
    Customer Advocacy
    Cisco Systems, Inc.
    www.cisco.com/go/smallbizsupport

  • How to make a cable for VWIC-1MFT-G703 connect to MGX 8830

    I want to connect a Cisco 1721 with VWIC-1MFT to MGX 8830 through E1 port but I don't know how to make a cable.What is the pin assignment of the e1 port on MGX 8830.
    Many thanks for who reply this.
    Thank you so much in advanced.

    The document Understanding 1-Port and 2-Port E1 Multiflex Trunk Voice/WAN Interface Cards (VWICs) has more information on Cisco 1-Port and 2-Port E1 Multiflex Voice/WAN Interface Card (VWIC-xMFT-E1, VWIC-xMFT-G703, and VWIC-2MFT-E1-DI).
    http://www.cisco.com/en/US/products/hw/routers/ps274/products_tech_note09186a00800b6e0f.shtml

  • Fax and modem via Drop & Insert card (VWIC 2MFT-E1-DI)

    Currently installing pair of 2610XM rtrs with Drop & Insert cards (VWIC 2MFT-E1-DI) between them.
    At each side there is PABX connected via E1 to Drop&Inser card, and 2Mbs leased line between locations.
    Configured 15 CH for data and 15 CH for voice.
    Data works fine.
    Voice services work fine as well, BUT!!!
    - When trying to use analog modems between locations it’s not working
    - When trying to send fax between locations, it’s hardly working (i.e. 1/10 success & even then copy is hardly readable).
    All problems not present when I bypass routers and 2Mbs leased line with 120Ohm cable.
    Any knowledge about similar problems?
    Any tip for sorting this kind of problems, or this is “by default” behavior for such setup?

    Thanks for tip, sorry for delay in reply (I was on leave).
    re synchronization, it is properly synchronized (as you can see in output attached.
    All other phone services/functions (standard voice calls, CallBack, CLIP etc.) and data transfer is working fine. If any problems with link sync I suppose there should be some problems with those as well.
    rtr#sh controller e1 0/0
    E1 0/0 is up.
    Applique type is Channelized E1 - balanced
    Description: Connecton to 2Mbs leased line
    No alarms detected.
    alarm-trigger is not set
    Version info Firmware: 20011015, FPGA: 11
    Framing is CRC4, Line Code is HDB3, Clock Source is Line.
    Data in current interval (530 seconds elapsed):
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
    Data in Interval 1:
    ! each Interval equals 900 Secs (15 min)
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
    Data in Interval 2:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
    ! etc, etc. Data in Interval XX:

  • Related to vmic2-2mft-g703 module on Router 2800

    I have purchased the vmic2-2mft-g703 for CISCO 2800 series router and want to know that can I configure this card two interfaces act as a simple data interfaces like router inbuilt ethernet interfaces? If yes then how? Please help me.

    Hello Ganesh,
    try to see if
    conf t
    controller e1 0/2/0
    is supported  it it looks like you need to go this way
    see
    http://www.cisco.com/en/US/products/hw/modules/ps2617/products_configuration_example09186a008052c920.shtml
    if so you need to configure a channel-group
    controller e1 0/2/0
    no shut
    channel-group 0 unframed
    a serial interface is created
    serial 0/2/0:0
    verify with your provider if you need an unframed or all timeslots in a group config
    Hope to help
    Giuseppe

  • VWIC-2MFT-T1

    Quick question. Can I configure one port on a VWIC-2MFT-T1 for PRI and another for T1 data? Or would it be better to use 2xVWIC-1MFT-T1s?

    If both ports are set as line, you will have 2 clocks driving the single Phase locked loop (PLL) clock recovery. This can sometimes lead to the PLL not being able to sync up to either clock reference and shows as slips on either of the ports.
    A fix here is to can set the second port as clock source internal. The card's PLL will sync to the clock source on the first port, and use this recovered clock to drive the second port TX. Assuming both T1's are in sync externally, this will not cause any issues as the recovered clock being used to drive the TX on the second port is the same as the RX clock on this port.
    If the two T1's are connected to dissimilar services that have different clocks then the only way to fix this is to use two single port cards or use the independent clock feature on the VWIC2 cards.

  • Is 1841 router compatible with wic module U WIC -2MFT –G703 ( 2 E1 ports) ?

    Hi frainds
    I have cisco 1841 router
    1841 Software (C1841-ADVSECURITYK9-M), Version 12.4(3g)
    ROM: System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1)
    with
    2 FastEthernet interfaces
    2 Serial(sync/async) interfaces
    1 Virtual Private Network (VPN) Module
    will this router supoort Uwic 2 mft-g703 card ( with 2 E1ports) ,

    These are the following modules supported on the 1841.
    http://www.cisco.com/en/US/prod/collateral/routers/ps5853/product_data_sheet0900aecd8016a59b.html
    The one you listed only works with the 1700 series which is end of life.
    "If this post answers your question, please click the "Correct Answer" button"

  • Cisco 2900 compatible with VWIC-1MFT-T1?

      Can a VWIC-1MFT-T1 card be used in a 2900 series router?  The compatibility tables on Cisco seem to indicate that it is not compatible, but are not definitive.  Anyone ever tried to put one of these in a 2900?

    No, you need VWIC2-MFT or VWIC3, see the compatibility reference:
    http://www.cisco.com/en/US/products/ps10537/products_relevant_interfaces_and_modules.html
    HTH,
    Chris

  • Problem with gateway voice in router 1841 or 1760

    Reading Cisco documentation , I see that router 1841 and 1841 does not support as Voice Gateway.
    My idea is to connect to him a Primary ISDN (30 channel B) so that it works like a PBX and users can make calls towards PSTN.
    Is possible to do this with these routers (1841, 1760)?
    Thanks.

    Using T1, E1 or G.703 multiflex trunk interface cards with cisco 1760 or 1800 series are both available.
    You can use these cards with 1760:
    VWIC-1MFT-T1
    One-port FJ-48 multiflex trunk - T1
    VWIC-2MFT-T1
    Two-port RJ-48 multiflex trunk - T1
    VWIC-2MFT-T1-DI
    Two-port RJ-48 multiflex trunk - T1 with drop and insert
    VWIC-1MFT-E1
    One-port RJ-48 multiflex trunk - E1
    VWIC-2MFT-E1
    Two-port RJ-48 multiflex trunk - E1
    VWIC_2MFT-E1-DI
    Two-port RJ-48 multiflex trunk - E1 with drop and insert
    VWIC-1MFT-G.703
    One-port RJ-48 multiflex trunk - E1 G.703
    VWIC-2MFT-G.703
    Two-port RJ-48 multiflex trunk - E1 G.703
    You can use these cards with 1800 series:
    VWIC-1MFT-T1
    1-port RJ-48 multiflex trunk voice/WAN interface card—T1
    VWIC-2MFT-T1
    2-port RJ-48 multiflex trunk voice/WAN interface card—T1
    VWIC-2MFT-T1-DI
    2-port RJ-48 multiflex trunk voice/WAN interface card—T1 with drop and insert
    VWIC-1MFT-E1
    1-port RJ-48 multiflex trunk voice/WAN interface card—E1
    VWIC-2MFT-E1
    2-port RJ-48 multiflex trunk voice/WAN interface card—E1
    VWIC-2MFT-E1-DI
    2-port RJ-48 multiflex trunk voice/WAN interface card—E1 with drop and insert
    VWIC-1MFT-G703
    1-port RJ-48 multiflex trunk voice/WAN interface card—G.703
    VWIC-2MFT-G703
    2-port RJ-48 multiflex trunk voice/WAN interface card—G.703
    you can get detailed information about compatibility with 1760 by using the below link:
    http://www.cisco.com/en/US/products/hw/routers/ps221/products_data_sheet09186a00800920f2.html
    you can get detailed information about compatibility with 1800 series by using the below link:
    http://www.cisco.com/en/US/products/ps5853/prod_module_install_config_guide09186a00802c47ef.html

  • Intregation iDCS with 2811 Router

    Greetings,
    first the scenario, i have one DX Quitum with E1 interface and Samsumg iDCS with TEPRI card for pbx to E1 convertion.
    We have purchased 1 2811 with VWIC-2MFT-E1, NM-PVDM2 64 and planning to buy CallManager 4.1.
    I want to intregate iDCS with 2811 and use the router as transcorder+gateway, i need to terminate outbound calls and well as receive inbound calls from US and UK DIDs i have.
    Please suggest if its better to use 2811 as gateway for termination aswell as inbound or should i use CCM.
    what IOS i need for 2811 to act as gateway for both SIP & H323 calls.
    i'm new to cisco solution so please excuse me if it sounds stupid Q.

    For supporting both SIP & H.323 its better to go for 'ipvoice' feature set of IOS 12.4 release.

  • Differences betwin Cisco Voice Cards

    Hi,
    I have a Media Gateway that is certificated to work with Cisco 2650XM using NM-HDV-1E1-30E or NM-HDV-2E1-60 cards to make trunk TDM and cisco work as ARU (Automatic response Unit) using TCL 2.0.
    Now, i have a cisco 2811 and seen VWIC-2MFT-E1 and VWIC-2MFT-G703 cards, that are more cheap than that the NM cards.
    My question is if can I use this VWIC to replace that NM voice cards for applications of ARU (Automatic response Unit) using TCL 2.0.
    Thanks.
    Fred

    Thanks,for your answer.
    How i now if my router alredy gave a dsp module ??
    Have a cli commando to check ???
    using show voice dsp i get:
    DSP DSP DSPWARE CURR BOOT PAK TX/RX
    TYPE NUM CH CODEC VERSION STATE STATE RST AI VOICEPORT TS ABORT PACK COUNT
    ==== === == ======== ======= ===== ======= === == ========= == ===== ============
    ----------------------------FLEX VOICE CARD 0 ------------------------------
    *DSP VOICE CHANNELS*
    DSP DSP DSPWARE CURR BOOT PAK TX/RX
    TYPE NUM CH CODEC VERSION STATE STATE RST AI VOICEPORT TS ABRT PACK COUNT
    ===== === == ======== ======= ===== ======= === == ========= == ==== ============
    *DSP SIGNALING CHANNELS*
    DSP DSP DSPWARE CURR BOOT PAK TX/RX
    TYPE NUM CH CODEC VERSION STATE STATE RST AI VOICEPORT TS ABRT PACK COUNT
    ===== === == ======== ======= ===== ======= === == ========= == ==== ============
    ------------------------END OF FLEX VOICE CARD 0 ----------------------------
    Thanks.

  • Channel assignment

    Hi,
    Can you help me to resolve this issue?
    1.I have sites A (Singapore) and B (India)
    2.At site A (Singapore) there is a Cisco router with VWIC-2MFT-T1 is connected to PBX T1 port.(120 users are sitting with a hand set)
    3.This router is also connected to IPLC by means of T1.
    4.At site B (India) there is a Cisco router 1841 with VWIC-2MFT-E1 and is connected to PBX E1 port.
    5.This site B router is connected to the IPLC cloud by means of LL 2Mbps.
    6.My problem is whenever the dialer at Site A (Singapore) use the 16th channel and generate the voice call to India over the IPLC cloud, Can the India router recognize the voice call in the same 16 channel? If so how to do it? Should I have to use the CoS to achieve this?
    Best Regards,
    S.Venkataraman

    T1 and E1 Controllers
    Cisco controllers negotiate the following parameters between an access server and a central office: line coding, framing, clocking, DS0/time slot provisioning, and signalling.
    Time slots are provisioned to meet the needs of particular network scenarios. T1 controllers have
    24 time slots, and E1 controllers have 30 time slots. To support traffic flow for one ISDN PRI line in a T1 configuration, use the pri-group command. To support traffic flow for analog calls over a channelized E1 line with recEive and transMit (E&M -- also ear and mouth) signalling, use the cas-group 1 timeslots 1-30 type e&m-fgb command. Most telephone companies do not support provisioning one trunk for different combinations of time slot services, though this provisioning is supported on Cisco controllers. On a T1 controller for example, time slots 1 to 10 could run PRI, time slots 11 to 20 could run channel-associated signalling (CAS), and time slots 21 to 24 could support leased-line grouping.
    The following example configures one of four T1 controllers on a Cisco AS5300 access server:
    as5300# configure terminal
    Enter configuration commands, one per line. End with CNTL/Z.
    as5300(config)# controller t1 ?
    <0-3> Controller unit number
    as5300(config)# controller t1 0
    as5300(config-controller)# framing esf
    as5300(config-controller)# linecode b8zs
    as5300(config-controller)# clock source line primary
    as5300(config-controller)# pri-group timeslots 1-24
    as5300(config-controller)#
    This example supports modem calls and circuit-switched digital calls over ISDN PRI.
    Non-ISDN Channelized T1 and Channelized E1 Lines
    A channelized T1 or channelized E1 line is an analog line that was originally intended to support analog voice calls, but has evolved to support analog data calls. ISDN is not sent across channelized T1 or E1 lines. Channelized T1 and channelized E1 lines are often referred to as CT1 and CE1. These channelized lines are found in "old world," non-ISDN telephone networks.
    The difference between traditional channelized lines (analog) and nonchannelized lines (ISDN) is that channelized lines have no built-in D channel. That is, all 24 channels on a T1 line only carry data. The signalling is in-band or associated to the data channels. Traditional channelized lines do not support digitized data calls (for example, BRI with 2B + D). Channelized lines support a variety of in-band signal types, such as ground start, loop start, wink start, immediate start, E&M, and R2.
    Signalling for channelized lines is configured with the cas-group controller configuration command. The following example configures E&M group B signalling on a T1 controller:
    as5300# configure terminal
    Enter configuration commands, one per line. End with CNTL/Z.
    as5300(config)# controller t1 0
    as5300(config-controller)# cas-group 1 timeslots 1-24 type ?
    e&m-fgb E & M Type II FGB
    e&m-fgd E & M Type II FGD
    e&m-immediate-start E & M Immediate Start
    fxs-ground-start FXS Ground Start
    fxs-loop-start FXS Loop Start
    r1-modified R1 Modified
    sas-ground-start SAS Ground Start
    sas-loop-start SAS Loop Start
    as5300(config-controller)# cas-group 1 timeslots 1-24 type e&m-fgb
    as5300(config-controller)# framing esf
    as5300(config-controller)# clock source line primary
    as5300(config-controller)#
    Try:
    http://www.cisco.com/en/US/products/sw/iosswrel/ps1831/products_configuration_guide_chapter09186a00800ca656.html#wp1001208

  • NM-HDV DSP Problems...

    Dear Friends
    I have a Cisco 3640 with NM-HDV-2E1-60 module with VWIC-2MFT-E1.
    The ios image is c3640-js-mz.123-19.bin and version is 12.3
    I have a strange problem with the NM-HDV module.
    I make the calls then these calls connect and after 2-3 seconds they drop, and the module doesn't free the channel, the channel stays busy...
    All the lights on the nm-hdv dsp light up green.
    I've tried to test the dsp's issuing the test dsp 0 command and then querying the dsp resource and status and it shows up the following
    Dsp firmware version: 4.1.41
    Maximum dsp count: 15
    On board dsp count: 15
    Jukebox available
    Total dsp channels available 60
    Total dsp channels allocated 60
    Total dsp free channels 0
    Querying dsp status......
    It doesn't show the dsp status...
    test dsp 1 (2, 3) commands say that Card 1 (2, 3) is not present.
    How can I be 100% that the problem is because of the DSP's (if it is like that)
    I'm saying this because I can buy new DSP's and change them, but I need to be 100% sure...
    Any reply is appreciated!

    Thanks for your reply.
    I've done some tests and here's the result.
    c3640_gw2# show dialplan number 12345678911
    Macro Exp.: 12345678911
    VoiceEncapPeer1
    peer type = voice, information type = voice,
    description = `',
    tag = 1, destination-pattern = `111+',
    answer-address = `', preference=0,
    CLID Restriction = None
    CLID Network Number = `'
    CLID Second Number sent
    CLID Override RDNIS = disabled,
    source carrier-id = `', target carrier-id = `',
    source trunk-group-label = `', target trunk-group-label = `',
    numbering Type = `unknown'
    group = 1, Admin state is up, Operation state is up,
    Outbound state is up,
    incoming called-number = `', connections/maximum = 1/unlimited,
    DTMF Relay = disabled,
    huntstop = disabled,
    in bound application associated: 'DEFAULT'
    out bound application associated: ''
    dnis-map =
    permission :both
    incoming COR list:maximum capability
    outgoing COR list:minimum requirement
    Translation profile (Incoming):
    Translation profile (Outgoing):
    incoming call blocking:
    translation-profile = `'
    disconnect-cause = `no-service'
    advertise 0x40 capacity_update_timer 25 addrFamily 4 oldAddrFamily 4
    type = pots, prefix = `11',
    forward-digits default
    session-target = `', voice-port = `0/0:0',
    direct-inward-dial = disabled,
    digit_strip = enabled,
    register E.164 number with GK = TRUE
    fax rate = system, payload size = 20 bytes
    supported-language = ''
    Time elapsed since last clearing of voice call statistics never
    Connect Time = 1876, Charged Units = 0,
    Successful Calls = 12, Failed Calls = 5, Incomplete Calls = 0
    Accepted Calls = 0, Refused Calls = 0,
    Last Disconnect Cause is "AC ",
    Last Disconnect Text is "dsp error (172)",
    Last Setup Time = 241131.
    Matched: 12345678911 Digits: 3
    Target:
    So it seems that the problem is really in DSPs.....

  • Trouble with my T1's and E1's in the lab - please help.... :-)

    I'm working through my CCIE Voice/Collaboration training materials and am just about finished with the physical construction of the lab.  At this time I'm just going to install a new T1 card into my BR1 router and I'm trying to get my T1 to HQ (HQ router) and my E1 to BR2 (Branch2 router) up and running.  I am enclosing the "show run", "show isdn status" and "show e1/t1 controller" outputs.  I am using a 2801 for my HQ router, a 2851 for my PSTN/IP-WAN router, and a 2811 for my BR2 router.
    I am using a T1 cable RJ-48C/RJ-48C.  I'm embarassed to say it - but I don't have a cable tester at the time.  I lended my backup out to a friend and my primary one is not working.  I'm also not 100% sure that I'm using the correct cable.  I have VWIC2-2MFT-T1/E1 cards in my routers and I have a 2851 (PSTN router) setup to give connectivity via the T1's to HQ and BR1 and E1 connectivity to BR2.  I have taken the liberty of attaching my configs, as mentioned I don't think I have cable issues because this is the case with all my cables.
    Main issue, in the "show isdn stat" the layer 1 status is "deactivated" and when I do a shut/no shut the status goes to "shutdown" and doesn't come back up despite my efforts to enable the interface.  The only way to fix it is to reboot the router.  I've got to be missing something - I just want to get my T1's and E1 up for my CCIE Lab.  I'm building my lab based on the CCIE Voice specification and have the ability to get it modified eventually to fit the CCIE Collaboration lab.
    ***PLEASE go easy on me - I'm sure there is a fundamental configuration item or concept I'm not thinking about so I'm preparing to look like a fool - but that's okay....it's part of learning.  :-)  ***
    Any help would be so much appreciated.  All configs are pasted below.......
    ==========================================================
    =================START OF BR2 CONFIG=======================
    BR2_RTR#show controllers e1
    E1 0/0/0 is down.
      Applique type is Channelized E1 - balanced
      Transmitter is sending remote alarm.
      Receiver has loss of signal.
      alarm-trigger is not set
      Version info Firmware: 20100222, FPGA: 13, spm_count = 0
      Framing is CRC4, Line Code is HDB3, Clock Source is Line.
      Data in current interval (895 seconds elapsed):
         0 Line Code Violations, 0 Path Code Violations
         0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
         0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 895 Unavail Secs
      Total Data (last 24 hours)
         0 Line Code Violations, 0 Path Code Violations,
         0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
         0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 86400 Unavail Secs
    BR2_RTR#show isdn stat
    Global ISDN Switchtype = primary-net5
    ISDN Serial0/0/0:15 interface
            dsl 0, interface ISDN Switchtype = primary-net5
        Layer 1 Status:
            DEACTIVATED
        Layer 2 Status:
            TEI = 0, Ces = 1, SAPI = 0, State = TEI_ASSIGNED
        Layer 3 Status:
            0 Active Layer 3 Call(s)
        Active dsl 0 CCBs = 0
        The Free Channel Mask:  0x00000000
        Number of L2 Discards = 0, L2 Session ID = 0
        Total Allocated ISDN CCBs = 0
    BR2_RTR#show inventory
    NAME: "2811 chassis", DESCR: "2811 chassis"
    PID: CISCO2811         , VID: V06 , SN: FTX1328A0D3
    NAME: "VWIC2-1MFT-T1/E1 - 1-Port RJ-48 Multiflex Trunk - T1/E1 on Slot 0 SubSlot 0", DESCR: "VWIC2-1MFT-T1/E1 - 1-Port RJ-48 Multiflex Trunk - T1/E1"
    PID: VWIC2-1MFT-T1/E1  , VID: V01 , SN: FOC11271UAU
    NAME: "WAN Interface Card - Serial 2T on Slot 0 SubSlot 1", DESCR: "WAN Interface Card - Serial 2T"
    PID: WIC-2T            , VID: V01, SN: 35759031
    NAME: "PVDMII DSP SIMM with three DSPs on Slot 0 SubSlot 5", DESCR: "PVDMII DSP SIMM with three DSPs"
    PID: PVDM2-48          , VID: V01 , SN: FOC12221GJE
    NAME: "AIM Service Engine 0", DESCR: "AIM Service Engine"
    PID: AIM-CUE           , VID: V03 , SN: FOC11505K9D
    NAME: "16 Port 10BaseT/100BaseTX EtherSwitch on Slot 1", DESCR: "16 Port 10BaseT/100BaseTX EtherSwitch"
    PID: NM-16ESW=         , VID: 1.0, SN: FOC09245Q0H
    NAME: "Power daughter card for 16 port EtherSwitch NM on Slot 1 SubSlot 0", DESCR: "Power daughter card for 16 port EtherSwitch NM"
    PID:                     , VID: 1.0, SN: FOC09243VGH
    NAME: "Gigabit(1000BaseT) module for EtherSwitch NM on Slot 1 SubSlot 1", DESCR: "Gigabit(1000BaseT) module for EtherSwitch NM"
    PID:                     , VID: 1.0, SN: FOC092034R1
    BR2_RTR#
    BR2_RTR#
    BR2_RTR#
    BR2_RTR#
    BR2_RTR#
    BR2_RTR#show run
    Building configuration...
    Current configuration : 9148 bytes
    ! No configuration change since last restart
    version 15.1
    service timestamps debug datetime msec
    service timestamps log datetime msec
    no service password-encryption
    hostname BR2_RTR
    boot-start-marker
    boot-end-marker
    card type e1 0 0
    enable secret 5 $1$kYuC$TYARPnIw8mjqiVM3CqM15.
    no aaa new-model
    clock timezone CET 1 0
    clock summer-time CET recurring 1 Sun Apr 1:00 last Sun Oct 1:00
    network-clock-participate wic 0
    dot11 syslog
    ip source-route
    ip cef
    ip dhcp excluded-address 192.168.30.1 192.168.30.49
    ip dhcp excluded-address 192.168.30.70 192.168.30.254
    ip dhcp pool PHONES
    network 192.168.30.0 255.255.255.0
    default-router 192.168.30.1
    option 150 ip 3.3.3.3
    no ip domain lookup
    no ipv6 cef
    multilink bundle-name authenticated
    isdn switch-type primary-net5
    voice service voip
    allow-connections sip to sip
    sip
      bind control source-interface Loopback0
      bind media source-interface Loopback0
      registrar server expires max 600 min 60
    voice class codec 1
    codec preference 1 g711ulaw
    codec preference 2 g729r8
    voice class h323 1
      h225 timeout tcp establish 3
    voice register global
    mode cme
    source-address 3.3.3.3 port 5060
    max-dn 20
    max-pool 10
    load 7960-7940 P0S3-08-6-00
    authenticate register
    tftp-path flash:
    create profile sync 1684632613172238
    voice register dn  1
    number 3005
    name BR2_Phone3
    voice register dn  2
    number 3006
    name BR2_Phone4
    voice register template  1
    no conference enable
    voice register dialplan 1
    type 7940-7960-others
    pattern 1 3...
    pattern 2 999
    voice register pool  1
    id mac 0008.E31B.7CD4
    type 7960
    number 1 dn 1
    template 1
    dtmf-relay sip-notify
    username 3005 password cisco
    description 3214-3005
    codec g711ulaw
    voice translation-rule 1
    rule 1 /^\(3...$\)/ /3214\1/
    voice translation-rule 2
    rule 1 /^32143/ /3/
    rule 2 /^\+3432143/ /3/
    voice translation-rule 3000
    rule 1 /^3000/ /1002/
    voice translation-profile 3000
    translate called 3000
    voice translation-profile 4digitDNIS
    translate called 2
    voice translation-profile 8digitANI
    translate calling 1
    voice-card 0
    crypto pki token default removal timeout 0
    license udi pid CISCO2811 sn FTX1328A0D3
    redundancy
    controller E1 0/0/0
    pri-group timeslots 1-3,16
    interface Loopback0
    ip address 3.3.3.3 255.255.255.255
    h323-gateway voip bind srcaddr 3.3.3.3
    interface FastEthernet0/0
    no ip address
    shutdown
    duplex auto
    speed auto
    interface Service-Engine0/0
    no ip address
    interface FastEthernet0/1
    no ip address
    duplex auto
    speed auto
    interface FastEthernet0/1.21
    description BR2-PHONES(RTR on a stick)
    encapsulation dot1Q 21
    ip address 192.168.30.1 255.255.255.0
    interface FastEthernet0/1.22
    description BR2-DATA(RTR on a stick)
    encapsulation dot1Q 22
    ip address 192.168.31.1 255.255.255.0
    interface Serial0/0/0:15
    no ip address
    encapsulation hdlc
    isdn switch-type primary-net5
    isdn incoming-voice voice
    isdn bchan-number-order ascending
    isdn outgoing display-ie
    no cdp enable
    interface Serial0/1/0
    no ip address
    shutdown
    clock rate 2000000
    interface Serial0/1/1
    description BR2-RTR_IP-WAN
    no ip address
    encapsulation frame-relay IETF
    no fair-queue
    frame-relay lmi-type ansi
    interface Serial0/1/1.1 point-to-point
    ip address 10.1.1.2 255.255.255.128
    frame-relay interface-dlci 301
    interface FastEthernet1/0
    description BR2-PHONE1
    switchport mode trunk
    switchport voice vlan 40
    no ip address
    spanning-tree portfast
    interface FastEthernet1/1
    description BR2-PHONE2
    switchport mode trunk
    switchport voice vlan 40
    no ip address
    spanning-tree portfast
    interface FastEthernet1/2
    no ip address
    interface FastEthernet1/3
    no ip address
    interface FastEthernet1/4
    no ip address
    interface FastEthernet1/5
    no ip address
    interface FastEthernet1/6
    no ip address
    interface FastEthernet1/7
    no ip address
    interface FastEthernet1/8
    no ip address
    interface FastEthernet1/9
    no ip address
    interface FastEthernet1/10
    no ip address
    interface FastEthernet1/11
    no ip address
    interface FastEthernet1/12
    no ip address
    interface FastEthernet1/13
    no ip address
    interface FastEthernet1/14
    no ip address
    interface FastEthernet1/15
    no ip address
    interface GigabitEthernet1/0
    no ip address
    interface Vlan1
    no ip address
    interface Vlan30
    description PHONES-VLAN-FOR-LAYER3-SWITCHING
    no ip address
    shutdown
    interface Vlan31
    description DATA-VLAN-FOR-LAYER3-SWITCHING
    no ip address
    shutdown
    router ospf 1
    network 3.3.3.3 0.0.0.0 area 0
    network 10.1.1.0 0.0.0.255 area 0
    network 192.168.30.0 0.0.0.255 area 0
    network 192.168.31.0 0.0.0.255 area 0
    network 192.168.0.0 0.0.255.255 area 0
    ip forward-protocol nd
    ip http server
    no ip http secure-server
    ip http path flash:/GUI
    ip route 192.168.100.0 255.255.255.0 10.1.1.1
    tftp-server flash:Desktops/320x212x12/CampusNight.png
    tftp-server flash:Desktops/320x212x12/CiscoFountain.png
    tftp-server flash:Desktops/320x212x12/MorroRock.png
    tftp-server flash:Desktops/320x212x12/NantucketFlowers.png
    tftp-server flash:Desktops/320x212x12/TN-CampusNight.png
    tftp-server flash:Desktops/320x212x12/TN-CiscoFountain.png
    tftp-server flash:Desktops/320x212x12/TN-Fountain.png
    tftp-server flash:Desktops/320x212x12/TN-MorroRock.png
    tftp-server flash:Desktops/320x212x12/TN-NantucketFlowers.png
    tftp-server flash:Desktops/320x212x12/Fountain.png
    tftp-server flash:Desktops/320x212x12/CiscoLogo.png
    tftp-server flash:Desktops/320x212x12/TN-CiscoLogo.png
    tftp-server flash:Desktops/320x212x12/List.xml
    tftp-server flash:Desktops/320x216x16/List.xml
    tftp-server flash:Desktops/320x212x16/List.xml
    tftp-server flash:ringtones/Analog1.raw
    tftp-server flash:ringtones/Analog2.raw
    tftp-server flash:ringtones/AreYouThere.raw
    tftp-server flash:ringtones/AreYouThereF.raw
    tftp-server flash:ringtones/Bass.raw
    tftp-server flash:ringtones/CallBack.raw
    tftp-server flash:ringtones/Chime.raw
    tftp-server flash:ringtones/Classic1.raw
    tftp-server flash:ringtones/Classic2.raw
    tftp-server flash:ringtones/ClockShop.raw
    tftp-server flash:ringtones/DistinctiveRingList.xml
    tftp-server flash:ringtones/Drums1.raw
    tftp-server flash:ringtones/Drums2.raw
    tftp-server flash:ringtones/FilmScore.raw
    tftp-server flash:ringtones/HarpSynth.raw
    tftp-server flash:ringtones/Jamaica.raw
    tftp-server flash:ringtones/KotoEffect.raw
    tftp-server flash:ringtones/MusicBox.raw
    tftp-server flash:ringtones/Piano1.raw
    tftp-server flash:ringtones/Piano2.raw
    tftp-server flash:ringtones/Pop.raw
    tftp-server flash:ringtones/Pulse1.raw
    tftp-server flash:ringtones/Ring1.raw
    tftp-server flash:ringtones/Ring2.raw
    tftp-server flash:ringtones/Ring3.raw
    tftp-server flash:ringtones/Ring4.raw
    tftp-server flash:ringtones/Ring5.raw
    tftp-server flash:ringtones/Ring6.raw
    tftp-server flash:ringtones/Ring7.raw
    tftp-server flash:ringtones/RingList.xml
    tftp-server flash:ringtones/Sax1.raw
    tftp-server flash:ringtones/Sax2.raw
    tftp-server flash:ringtones/Vibe.raw
    tftp-server flash:PHONE/7940-7960/P0S3-08-6-00.loads alias P0S3-08-6-00.loads
    tftp-server flash:PHONE/7940-7960/P0S3-08-6-00.sb2 alias P0S3-08-6-00.sb2
    tftp-server flash:PHONE/7940-7960/P0S3-08-6-00.bin alias P0S3-08-6-00.bin
    tftp-server flash:PHONE/7940-7960/P0S3-08-6-00.sbn alias P0S3-08-6-00.sbn
    control-plane
    voice-port 0/0/0:15
    translation-profile outgoing 4digitDNIS
    mgcp profile default
    dial-peer voice 999 pots
    translation-profile outgoing 8digitANI
    destination-pattern 999
    port 0/0/0:15
    forward-digits 3
    dial-peer voice 1 voip
    incoming called-number .
    dial-peer voice 901134 pots
    destination-pattern 901134T
    port 0/0/0:15
    dial-peer voice 3000 voip
    translation-profile outgoing 3000
    destination-pattern 3000
    session target ipv4:192.168.15.23
    voice-class codec 1
    voice-class h323 1
    telephony-service
    no auto-reg-ephone
    max-ephones 10
    max-dn 20
    ip source-address 3.3.3.3 port 2000
    network-locale ES
    time-format 24
    date-format dd-mm-yy
    max-conferences 8 gain -6
    web admin system name admin password cisco
    dn-webedit
    transfer-system full-consult
    create cnf-files version-stamp 7960 Jan 23 2014 05:43:52
    ephone-template  1
    softkeys connected  Hold Select Trnsfer Endcall HLog Park
    ephone-dn  1
    number 3001
    name BR2_Phone1
    ephone-dn  2
    number 3002
    name BR2_Phone2
    ephone  1
    device-security-mode none
    description 3214-3001
    mac-address 0008.A3FD.3A32
    ephone-template 1
    max-calls-per-button 5
    busy-trigger-per-button 3
    type 7960
    button  1:1
    ephone  2
    device-security-mode none
    description 3214-3002
    mac-address 0017.E0C6.E232
    ephone-template 1
    max-calls-per-button 5
    busy-trigger-per-button 3
    type 7961
    button  1:2
    banner motd ^CBR2 ROUTER CUCME/CUE^C
    line con 0
    password cisco
    logging synchronous
    login
    line aux 0
    line 194
    no activation-character
    no exec
    transport preferred none
    transport input all
    transport output lat pad telnet rlogin lapb-ta mop udptn v120 ssh
    line vty 0 4
    password cisco
    login
    transport input all
    line vty 5 15
    password cisco
    login
    transport input all
    scheduler allocate 20000 1000
    ntp server 172.30.1.2
    end
    ===========END OF BR2 CONFIG=================
    ===========START OF HQ CONFIG================
    HQ-RTR#show inventory
    NAME: "chassis", DESCR: "2801 chassis"
    PID: CISCO2801         , VID: V02 , SN: FTX1016Y07Z
    NAME: "motherboard", DESCR: "C2801 Motherboard with 2 Fast Ethernet"
    PID: CISCO2801         , VID: V02 , SN: FOC10140N6M
    NAME: "WIC/VIC 2", DESCR: "Two port T1 voice interface daughtercard"
    PID: VWIC-2MFT-T1=     , VID: 1.0, SN: 32867042
    NAME: "WIC/VIC/HWIC 3", DESCR: "WAN Interface Card - Serial 2T"
    PID: WIC-2T=           , VID: 1.0, SN: 32195023
    NAME: "PVDM 0", DESCR: "PVDMII DSP SIMM with three DSPs"
    PID: PVDM2-48          , VID: V01 , SN: FOC132935YB
    HQ-RTR#
    HQ-RTR#show controllers t1
    T1 0/2/0 is down.
      Applique type is Channelized T1
      Cablelength is long gain36 0db
      Transmitter is sending remote alarm.
      Receiver has loss of signal.
      alarm-trigger is not set
      Soaking time: 3, Clearance time: 10
      AIS State:Clear  LOS State:Clear  LOF State:Clear
      Version info Firmware: 20090113, FPGA: 20, spm_count = 0
      Framing is ESF, Line Code is B8ZS, Clock Source is Line.
      CRC Threshold is 320. Reported from firmware  is 320.
      Data in current interval (709 seconds elapsed):
         0 Line Code Violations, 0 Path Code Violations
         0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
         0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 709 Unavail Secs
      Total Data (last 24 hours)
         0 Line Code Violations, 0 Path Code Violations,
         0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
         0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 86400 Unavail Secs
    T1 0/2/1 is down.
      Applique type is Channelized T1
      Cablelength is long gain36 0db
      Transmitter is sending remote alarm.
      Receiver has loss of signal.
      alarm-trigger is not set
      Soaking time: 3, Clearance time: 10
      AIS State:Clear  LOS State:Clear  LOF State:Clear
      Version info Firmware: 20090113, FPGA: 20, spm_count = 0
      Framing is ESF, Line Code is B8ZS, Clock Source is Line.
      CRC Threshold is 320. Reported from firmware  is 320.
      Data in current interval (709 seconds elapsed):
         0 Line Code Violations, 0 Path Code Violations
         0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
         0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 709 Unavail Secs
      Total Data (last 24 hours)
         0 Line Code Violations, 0 Path Code Violations,
         0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
         0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 86400 Unavail Secs
    HQ-RTR#show isdn stat
    Global ISDN Switchtype = primary-ni
    ISDN Serial0/2/0:23 interface
            dsl 0, interface ISDN Switchtype = primary-ni
        Layer 1 Status:
            DEACTIVATED
        Layer 2 Status:
            TEI = 0, Ces = 1, SAPI = 0, State = TEI_ASSIGNED
        Layer 3 Status:
            0 Active Layer 3 Call(s)
        Active dsl 0 CCBs = 0
        The Free Channel Mask:  0x00000000
        Number of L2 Discards = 0, L2 Session ID = 0
        Total Allocated ISDN CCBs = 0
    HQ-RTR#
    HQ-RTR#show run
    Building configuration...
    Current configuration : 6734 bytes
    ! Last configuration change at 02:32:03 UTC Tue Feb 4 2014
    version 15.1
    service timestamps debug datetime msec
    service timestamps log datetime msec
    no service password-encryption
    hostname HQ-RTR
    boot-start-marker
    boot-end-marker
    logging buffered 512000 informational
    enable secret 5 $1$K8GP$JbYRetpgnaxvy2wnjrPDW/
    no aaa new-model
    network-clock-participate wic 2
    dot11 syslog
    ip source-route
    ip dhcp excluded-address 192.168.11.1 192.168.11.10
    ip dhcp excluded-address 192.168.12.1 192.168.12.10
    ip dhcp excluded-address 192.168.13.1 192.168.13.10
    ip dhcp excluded-address 192.168.14.1 192.168.14.10
    ip dhcp excluded-address 192.168.16.1 192.168.16.10
    ip dhcp excluded-address 192.168.17.1 192.168.17.10
    ip dhcp pool HQ-BR1-Pool
    import all
    network 192.168.11.0 255.255.255.0
    option 150 ip 10.10.210.10
    default-router 192.168.11.1
    domain-name proctorlabs.com
    dns-server 8.8.4.4 8.8.8.8
    lease 8
    ip dhcp pool BR2-Pool
    import all
    network 192.168.12.0 255.255.255.0
    option 150 ip 10.10.202.1
    default-router 192.168.12.1
    domain-name proctorlabs.com
    dns-server 8.8.4.4 8.8.8.8
    lease 8
    ip dhcp pool PSTN-Pool
    import all
    network 192.168.13.0 255.255.255.0
    option 150 ip 10.10.100.2
    default-router 192.168.13.1
    domain-name proctorlabs.com
    dns-server 8.8.4.4 8.8.8.8
    lease 8
    ip dhcp pool Laptop-Pool
    import all
    network 192.168.14.0 255.255.255.0
    default-router 192.168.14.1
    domain-name proctorlabs.com
    dns-server 8.8.4.4 8.8.8.8
    lease 8
    ip dhcp pool WIRELESS-HOME
    import all
    network 192.168.16.0 255.255.255.0
    default-router 192.168.16.1
    dns-server 8.8.8.8 4.2.2.2
    domain-name proctorlabs.com
    lease 8
    ip cef
    no ip domain lookup
    ip domain name proctorlabs.com
    no ipv6 cef
    multilink bundle-name authenticated
    isdn switch-type primary-ni
    voice service voip
    sip
      bind control source-interface Loopback0
      bind media source-interface Loopback0
    voice class codec 1
    codec preference 1 g711ulaw
    codec preference 2 g729r8
    voice-card 0
    crypto pki token default removal timeout 0
    license udi pid CISCO2801 sn FTX1016Y07Z
    archive
    log config
      hidekeys
    controller T1 0/2/0
    pri-group timeslots 1-3,24
    controller T1 0/2/1
    interface Loopback0
    ip address 1.1.1.1 255.255.255.255
    interface FastEthernet0/0
    description (Outside Public Interface)
    ip address dhcp
    ip access-group FW-IN in
    no ip unreachables
    ip mtu 1300
    ip nat outside
    ip virtual-reassembly in
    duplex auto
    speed auto
    no cdp enable
    interface FastEthernet0/1
    no ip address
    duplex auto
    speed auto
    interface FastEthernet0/1.11
    description (Inside Private Interface)
    encapsulation dot1Q 11
    ip address 192.168.11.1 255.255.255.0
    ip nat inside
    ip virtual-reassembly in
    interface FastEthernet0/1.12
    description (Inside Private Interface)
    encapsulation dot1Q 12
    ip address 192.168.12.1 255.255.255.0
    ip nat inside
    ip virtual-reassembly in
    interface FastEthernet0/1.13
    description (Inside Private Interface)
    encapsulation dot1Q 13
    ip address 192.168.13.1 255.255.255.0
    ip nat inside
    ip virtual-reassembly in
    interface FastEthernet0/1.14
    description (Inside Private Interface)
    encapsulation dot1Q 14
    ip address 192.168.14.1 255.255.255.0
    ip nat inside
    ip virtual-reassembly in
    interface FastEthernet0/1.15
    description LAB-SERVERS
    encapsulation dot1Q 15
    ip address 192.168.15.1 255.255.255.0
    ip nat inside
    ip virtual-reassembly in
    interface FastEthernet0/1.16
    description WIRELESS-HOME
    encapsulation dot1Q 16
    ip address 192.168.16.1 255.255.255.0
    ip nat inside
    ip virtual-reassembly in
    interface FastEthernet0/1.17
    description LAB-HQ-PHONES
    encapsulation dot1Q 17
    ip address 192.168.17.1 255.255.255.0
    ip helper-address 192.168.15.22
    ip nat inside
    ip virtual-reassembly in
    interface FastEthernet0/1.18
    description LAB-HQ-DATA
    encapsulation dot1Q 18
    ip address 192.168.18.1 255.255.255.0
    ip helper-address 192.168.15.22
    ip nat inside
    ip virtual-reassembly in
    interface FastEthernet0/1.501
    description PSTN-RTR_MGMT-NETWORK
    encapsulation dot1Q 501
    ip address 172.30.1.1 255.255.255.0
    ip nat inside
    ip virtual-reassembly in
    interface Serial0/2/0:23
    no ip address
    encapsulation hdlc
    isdn switch-type primary-ni
    isdn incoming-voice voice
    isdn outgoing display-ie
    no cdp enable
    interface Serial0/3/0
    description HQ-RTR_IP-WAN
    no ip address
    encapsulation frame-relay IETF
    no fair-queue
    frame-relay lmi-type ansi
    interface Serial0/3/0.1 point-to-point
    ip address 10.1.1.1 255.255.255.128
    ip ospf mtu-ignore
    snmp trap link-status
    frame-relay interface-dlci 103
    interface Serial0/3/0.2 point-to-point
    ip address 10.1.1.129 255.255.255.128
    ip ospf mtu-ignore
    snmp trap link-status
    frame-relay interface-dlci 102
    interface Serial0/3/1
    no ip address
    shutdown
    clock rate 2000000
    router ospf 1
    network 1.1.1.1 0.0.0.0 area 0
    network 10.1.1.0 0.0.0.255 area 0
    network 172.30.1.0 0.0.0.3 area 0
    network 192.168.0.0 0.0.255.255 area 0
    ip forward-protocol nd
    no ip http server
    no ip http secure-server
    ip nat inside source list 101 interface FastEthernet0/0 overload
    ip route 0.0.0.0 0.0.0.0 10.0.0.1 254
    ip route 192.168.100.0 255.255.255.0 172.30.1.2
    ip route 0.0.0.0 0.0.0.0 dhcp
    access-list 101 deny   ip 192.168.0.0 0.0.255.255 10.10.0.0 0.0.255.255
    access-list 101 permit ip 192.168.0.0 0.0.255.255 any
    access-list 102 permit udp any any eq bootps
    access-list 102 permit udp any any eq bootpc
    access-list 102 permit udp any eq bootpc any
    access-list 102 permit udp any eq bootps any
    disable-eadi
    control-plane
    voice-port 0/2/0:23
    mgcp fax t38 ecm
    mgcp profile default
    dial-peer voice 91212 pots
    description PSTN-CALLS-TO-NYC-AREA-CODE
    destination-pattern 91212T
    port 0/2/0:23
    forward-digits all
    dial-peer voice 1 pots
    description INCOMING-DIAL-PEER_PSTN
    incoming called-number .
    direct-inward-dial
    port 0/2/0:23
    dial-peer voice 1000 voip
    destination-pattern 2123941...
    session protocol sipv2
    session target ipv4:192.168.15.23
    incoming called-number .
    voice-class codec 1
    dtmf-relay rtp-nte
    no vad
    dial-peer voice 1001 voip
    preference 1
    destination-pattern 2123941...
    session protocol sipv2
    session target ipv4:192.168.15.22
    incoming called-number .
    voice-class codec 1
    dtmf-relay rtp-nte
    no vad
    sip-ua
    retry invite 2
    timers trying 300
    line con 0
    password cisco
    logging synchronous
    login
    line aux 0
    line vty 0 4
    exec-timeout 30 0
    privilege level 15
    password cisco
    logging synchronous
    login
    transport input telnet ssh
    line vty 5 15
    exec-timeout 30 0
    privilege level 15
    password cisco
    logging synchronous
    login
    transport input telnet ssh
    scheduler allocate 20000 1000
    end
    HQ-RTR#
    =============END OF HQ CONFIG=============
    =======START OF PSTN-IP-WAN_RTR CONFIG=========
    PSTN_IP-WAN_RTR#show inventory
    NAME: "2851 chassis", DESCR: "2851 chassis"
    PID: CISCO2851         , VID: V01 , SN: FTX0922A1E7
    NAME: "VWIC2-2MFT-T1/E1 - 2-Port RJ-48 Multiflex Trunk - T1/E1 on Slot 0 SubSlot 0", DESCR: "VWIC2-2MFT-T1/E1 - 2-Port RJ-48 Multiflex Trunk - T1/E1"
    PID: VWIC2-2MFT-T1/E1  , VID: V01 , SN: FOC11063UF9
    NAME: "WAN Interface Card - Serial 2T on Slot 0 SubSlot 1", DESCR: "WAN Interface Card - Serial 2T"
    PID: WIC-2T      , VID: V01, SN: 35845606
    NAME: "Two port T1 voice interface daughtercard on Slot 0 SubSlot 2", DESCR: "Two port T1 voice interface daughtercard"
    PID: VWIC-2MFT-T1=     , VID: 1.0, SN: 29803060
    NAME: "WAN Interface Card - Serial 2T on Slot 0 SubSlot 3", DESCR: "WAN Interface Card - Serial 2T"
    PID: WIC-2T=           , VID: 1.0, SN: 23188546
    NAME: "PVDMII DSP SIMM with Two DSPs on Slot 0 SubSlot 4", DESCR: "PVDMII DSP SIMM with Two DSPs"
    PID: PVDM2-32          , VID: V01 , SN: FOC12045356
    PSTN_IP-WAN_RTR#show controllers t1
    T1 0/2/0 is down.
      Applique type is Channelized T1
      Cablelength is long gain36 0db
      Description: HQ_T1
      Transmitter is sending remote alarm.
      Receiver has loss of signal.
      alarm-trigger is not set
      Soaking time: 3, Clearance time: 10
      AIS State:Clear  LOS State:Clear  LOF State:Clear
      Version info Firmware: 20071129, FPGA: 20, spm_count = 0
      Framing is ESF, Line Code is B8ZS, Clock Source is Internal.
      CRC Threshold is 320. Reported from firmware  is 320.
      Data in current interval (852 seconds elapsed):
         0 Line Code Violations, 0 Path Code Violations
         0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
         0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 852 Unavail Secs
      Total Data (last 24 hours)
         0 Line Code Violations, 0 Path Code Violations,
         0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
         0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 86400 Unavail Secs
    T1 0/2/1 is down.
      Applique type is Channelized T1
      Cablelength is long gain36 0db
      Description: BR1_T1
      Transmitter is sending remote alarm.
      Receiver has loss of signal.
      alarm-trigger is not set
      Soaking time: 3, Clearance time: 10
      AIS State:Clear  LOS State:Clear  LOF State:Clear
      Version info Firmware: 20071129, FPGA: 20, spm_count = 0
      Framing is ESF, Line Code is B8ZS, Clock Source is Internal.
      CRC Threshold is 320. Reported from firmware  is 320.
      Data in current interval (854 seconds elapsed):
         0 Line Code Violations, 0 Path Code Violations
         0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
         0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 854 Unavail Secs
      Total Data (last 24 hours)
         0 Line Code Violations, 0 Path Code Violations,
         0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
         0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 86400 Unavail Secs
    PSTN_IP-WAN_RTR#show controllers e1
    E1 0/0/0 is down.
      Applique type is Channelized E1 - balanced
      Cablelength is Unknown
      Description: BR2_E1
      Transmitter is sending remote alarm.
      Receiver has loss of signal.
      alarm-trigger is not set
      Version info Firmware: 20071011, FPGA: 13, spm_count = 0
      Framing is CRC4, Line Code is HDB3, Clock Source is Internal.
      Data in current interval (862 seconds elapsed):
         0 Line Code Violations, 0 Path Code Violations
         0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
         0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 862 Unavail Secs
      Total Data (last 24 hours)
         0 Line Code Violations, 0 Path Code Violations,
         0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
         0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 86400 Unavail Secs
    E1 0/0/1 is down.
      Applique type is Channelized E1 - balanced
      Cablelength is Unknown
      Transmitter is sending remote alarm.
      Receiver has loss of signal.
      alarm-trigger is not set
      Version info Firmware: 20071011, FPGA: 13, spm_count = 0
      Framing is CRC4, Line Code is HDB3, Clock Source is Internal.
      Data in current interval (864 seconds elapsed):
         0 Line Code Violations, 0 Path Code Violations
         0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
         0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 864 Unavail Secs
      Total Data (last 24 hours)
         0 Line Code Violations, 0 Path Code Violations,
         0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
         0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 86400 Unavail Secs
    PSTN_IP-WAN_RTR#
    PSTN_IP-WAN_RTR#
    PSTN_IP-WAN_RTR#show isdn status
    Global ISDN Switchtype = primary-net5
    ISDN Serial0/0/0:15 interface
            ******* Network side configuration *******
            dsl 0, interface ISDN Switchtype = primary-net5
        Layer 1 Status:
            DEACTIVATED
        Layer 2 Status:
            TEI = 0, Ces = 1, SAPI = 0, State = TEI_ASSIGNED
        Layer 3 Status:
            0 Active Layer 3 Call(s)
        Active dsl 0 CCBs = 0
        The Free Channel Mask:  0x00000000
        Number of L2 Discards = 0, L2 Session ID = 0
    ISDN Serial0/0/1:15 interface
            ******* Network side configuration *******
            dsl 1, interface ISDN Switchtype = primary-net5
        Layer 1 Status:
            DEACTIVATED
        Layer 2 Status:
            TEI = 0, Ces = 1, SAPI = 0, State = TEI_ASSIGNED
        Layer 3 Status:
            0 Active Layer 3 Call(s)
        Active dsl 1 CCBs = 0
        The Free Channel Mask:  0x00000000
        Number of L2 Discards = 0, L2 Session ID = 0
    ISDN Serial0/2/0:23 interface
            ******* Network side configuration *******
            dsl 2, interface ISDN Switchtype = primary-ni
        Layer 1 Status:
            DEACTIVATED
        Layer 2 Status:
            TEI = 0, Ces = 1, SAPI = 0, State = TEI_ASSIGNED
        Layer 3 Status:
            0 Active Layer 3 Call(s)
        Active dsl 2 CCBs = 0
        The Free Channel Mask:  0x00000000
        Number of L2 Discards = 0, L2 Session ID = 0
    ISDN Serial0/2/1:23 interface
            ******* Network side configuration *******
            dsl 3, interface ISDN Switchtype = primary-ni
        Layer 1 Status:
            DEACTIVATED
        Layer 2 Status:
            TEI = 0, Ces = 1, SAPI = 0, State = TEI_ASSIGNED
        Layer 3 Status:
            0 Active Layer 3 Call(s)
        Active dsl 3 CCBs = 0
        The Free Channel Mask:  0x00000000
        Number of L2 Discards = 0, L2 Session ID = 0
        Total Allocated ISDN CCBs = 0
    PSTN_IP-WAN_RTR#
    PSTN_IP-WAN_RTR#show run
    Building configuration...
    Current configuration : 6518 bytes
    ! Last configuration change at 23:02:02 CST Tue Feb 4 2014
    version 12.4
    service timestamps debug datetime msec
    service timestamps log datetime msec
    no service password-encryption
    hostname PSTN_IP-WAN_RTR
    boot-start-marker
    boot-end-marker
    card type e1 0 0
    logging message-counter syslog
    enable secret 5 $1$rLlG$MPPST59p5rs0FfXu8OXp1.
    no aaa new-model
    clock timezone CST -6
    clock summer-time CDT recurring
    network-clock-participate wic 0
    network-clock-participate wic 2
    dot11 syslog
    ip source-route
    ip cef
    ip dhcp excluded-address 192.168.100.1 192.168.100.10
    ip dhcp pool PSTN-PHONE
       network 192.168.100.0 255.255.255.0
       default-router 192.168.100.1
       option 150 ip 192.168.100.1
    no ip domain lookup
    no ipv6 cef
    multilink bundle-name authenticated
    frame-relay switching
    isdn switch-type primary-net5
    voice translation-rule 1
    rule 1 /^011\(.*\)/ /\1/
    rule 2 /^1\(.*\)/ /&/
    rule 3 /^00\(.*\)/ /\1/
    rule 4 /^617\(.*\)/ /1&/
    rule 5 /^212\(.*\)/ /1&/
    voice translation-rule 2
    rule 1 /^617/ /1&/
    rule 2 /^212/ /1&/
    voice translation-rule 3
    rule 1 /^212/ /1&/
    rule 2 /^34/ /&/
    voice translation-rule 4
    rule 1 /^617/ /1&/
    rule 2 /^34/ /&/
    voice translation-profile BR1-OUT
    translate calling 3
    voice translation-profile BR2-OUT
    translate calling 2
    voice translation-profile HQ-OUT
    translate calling 4
    voice translation-profile PSTN-IN
    translate called 1
    voice-card 0
    crypto pki token default removal timeout 0
    archive
    log config
      hidekeys
    controller E1 0/0/0
    clock source internal
    pri-group timeslots 1-3,16
    description BR2_E1
    controller E1 0/0/1
    clock source internal
    pri-group timeslots 1-3,16
    controller T1 0/2/0
    clock source internal
    pri-group timeslots 1-3,24
    description HQ_T1
    controller T1 0/2/1
    clock source internal
    pri-group timeslots 1-3,24
    description BR1_T1
    interface GigabitEthernet0/0
    no ip address
    duplex auto
    speed auto
    interface GigabitEthernet0/0.13
    description PSTN-PHONE_LAN
    encapsulation dot1Q 13
    ip address 192.168.100.1 255.255.255.0
    interface GigabitEthernet0/1
    description MGMT-CONNECTION-via-WIFI
    ip address 172.30.1.2 255.255.255.0
    duplex auto
    speed auto
    interface Serial0/0/0:15
    description BR2-PSTN-CONNECTION
    no ip address
    encapsulation hdlc
    isdn switch-type primary-net5
    isdn protocol-emulate network
    isdn incoming-voice voice
    no cdp enable
    interface Serial0/0/1:15
    description BR2-PSTN-CONNECTION
    no ip address
    encapsulation hdlc
    isdn switch-type primary-net5
    isdn protocol-emulate network
    isdn incoming-voice voice
    no cdp enable
    interface Serial0/1/0
    description FR_to_BR2-RTR
    no ip address
    encapsulation frame-relay IETF
    clock rate 64000
    frame-relay lmi-type ansi
    frame-relay intf-type dce
    frame-relay route 301 interface Serial0/3/0 103
    interface Serial0/1/1
    no ip address
    shutdown
    clock rate 2000000
    interface Serial0/2/0:23
    description HQ-PSTN-CONNECTION
    no ip address
    encapsulation hdlc
    isdn switch-type primary-ni
    isdn protocol-emulate network
    isdn incoming-voice voice
    no cdp enable
    interface Serial0/2/1:23
    no ip address
    encapsulation hdlc
    isdn switch-type primary-ni
    isdn protocol-emulate network
    isdn incoming-voice voice
    no cdp enable
    interface Serial0/3/0
    description FR_to_HQ-RTR_point-to-point-BR1andBR2
    no ip address
    encapsulation frame-relay IETF
    clock rate 64000
    frame-relay lmi-type ansi
    frame-relay intf-type dce
    frame-relay route 102 interface Serial0/3/1 201
    frame-relay route 103 interface Serial0/1/0 301
    interface Serial0/3/1
    description FR_to_BR1-RTR-to-HQ-RTR
    no ip address
    encapsulation frame-relay IETF
    frame-relay lmi-type ansi
    frame-relay intf-type dce
    frame-relay route 201 interface Serial0/3/0 102
    ip forward-protocol nd
    ip route 1.1.1.1 255.255.255.255 172.30.1.1
    ip route 2.2.2.2 255.255.255.255 172.30.1.1
    ip route 3.3.3.3 255.255.255.255 172.30.1.1
    ip route 10.1.1.0 255.255.255.0 172.30.1.1
    ip route 192.168.14.0 255.255.255.0 172.30.1.1
    ip route 192.168.15.0 255.255.255.0 172.30.1.1
    ip route 192.168.16.0 255.255.255.0 172.30.1.1
    ip route 192.168.17.0 255.255.255.0 172.30.1.1
    ip route 192.168.20.0 255.255.255.0 172.30.1.1
    ip route 192.168.21.0 255.255.255.0 172.30.1.1
    ip route 192.168.30.0 255.255.255.0 172.30.1.1
    ip route 192.168.31.0 255.255.255.0 172.30.1.1
    no ip http server
    no ip http secure-server
    tftp-server flash:P0030801SR02.bin
    tftp-server flash:P0030801SR02.loads
    tftp-server flash:P0030801SR02.sb2
    tftp-server flash:P0030801SR02.sbn
    tftp-server P0030801SR02.txt
    control-plane
    voice-port 0/0/0:15
    voice-port 0/2/0:23
    voice-port 0/0/1:15
    voice-port 0/2/1:23
    ccm-manager fax protocol cisco
    mgcp fax t38 ecm
    dial-peer voice 1 pots
    incoming called-number .
    direct-inward-dial
    dial-peer voice 10 pots
    description HQ-NATIONAL-CALLS-DIAL-PEER
    destination-pattern 2123941...
    port 0/2/0:23
    forward-digits all
    dial-peer voice 20 pots
    description BR1-NATIONAL-CALLS-DIAL-PEER
    destination-pattern 6178632...
    port 0/2/1:23
    forward-digits all
    dial-peer voice 30 pots
    description BR2-NATIONAL-CALLS-DIAL-PEER
    destination-pattern 32143...
    port 0/0/0:15
    forward-digits all
    dial-peer voice 31 pots
    description BR2-INTL-CALLS-DIAL-PEER
    destination-pattern 3432143...
    port 0/0/0:15
    forward-digits all
    telephony-service
    em logout 0:0 0:0 0:0
    max-ephones 2
    max-dn 10
    ip source-address 192.168.100.1 port 2000
    load 7960-7940 P00303020214
    keepalive 10
    max-conferences 4 gain -6
    transfer-system full-consult
    create cnf-files version-stamp Jan 01 2002 00:00:00
    ephone-dn  1
    number 12123945001
    label +8087812321
    description NYC
    name NYC-PSTN
    ephone-dn  2
    number 16178635001
    label 911+999
    description BOSTON
    name BOSTON-PSTN
    ephone-dn  3
    number 32145001
    label 18005551234
    description SPAIN
    name SPAIN-PSTN
    ephone-dn  4
    number 3432145002
    description SPAIN
    name SPAIN-PSTN-INTL
    ephone-dn  5
    number 5005
    label 7812321
    description 7812321
    ephone-dn  6
    number 5006
    label x5005
    description OFFICE PHONE
    ephone  1
    device-security-mode none
    mac-address 0008.A3FD.39FF
    type 7960
    button  1:1 2:2 3:3 4:4
    button  5:5
    banner motd ^CC PSTN-IP-WAN ROUTER ^C
    line con 0
    password cisco
    logging synchronous
    login
    line aux 0
    line vty 0 4
    password cisco
    login
    transport input all
    line vty 5 15
    password cisco
    login
    transport input all
    scheduler allocate 20000 1000
    ntp master
    end
    PSTN_IP-WAN_RTR#

    I have went ahead and re-enabled the voice-ports just because I left that out of my original output.  See below.....
    Do you think I ordered 3 factory made T1 cables from BlackBox and ALL of them came back to me bad?  Or perhaps they might not have made them as cross over cables......hmm...any other suggestions?
    BR2_RTR(config)#voice-port 0/0/0:15
    BR2_RTR(config-voiceport)#no shut
    BR2_RTR(config-voiceport)#do sh voice port summ
    BR2_RTR(config-voiceport)#do sh voice port summ
                                               IN       OUT
    PORT            CH   SIG-TYPE   ADMIN OPER STATUS   STATUS   EC
    =============== == ============ ===== ==== ======== ======== ==
    0/0/0:15        01  isdn-voice  up    down none     none     y
    0/0/0:15        02  isdn-voice  up    down none     none     y
    0/0/0:15        03  isdn-voice  up    down none     none     y
    50/0/1          1      efxs     up    dorm on-hook  idle     y
    50/0/2          1      efxs     up    dorm on-hook  idle     y
    PWR FAILOVER PORT        PSTN FAILOVER PORT
    =================        ==================
    HQ-RTR(config)#voice-port 0/2/0:23
    HQ-RTR(config-voiceport)#no shut
    HQ-RTR(config-voiceport)#
    HQ-RTR(config-voiceport)#
    HQ-RTR(config-voiceport)#do sh voice port summ
                                               IN       OUT
    PORT            CH   SIG-TYPE   ADMIN OPER STATUS   STATUS   EC
    =============== == ============ ===== ==== ======== ======== ==
    0/2/0:23        01  isdn-voice  up    down none     none     y
    0/2/0:23        02  isdn-voice  up    down none     none     y
    0/2/0:23        03  isdn-voice  up    down none     none     y
    PWR FAILOVER PORT        PSTN FAILOVER PORT
    =================        ==================
    PSTN_IP-WAN_RTR#conf t
    Enter configuration commands, one per line.  End with CNTL/Z.
    PSTN_IP-WAN_RTR(config)#voice-p
    PSTN_IP-WAN_RTR(config)#voice-port 0/0/0:15
    PSTN_IP-WAN_RTR(config-voiceport)#no shut
    PSTN_IP-WAN_RTR(config-voiceport)#exit
    PSTN_IP-WAN_RTR(config)#voice-por
    PSTN_IP-WAN_RTR(config)#voice-port 0/2/0:23
    PSTN_IP-WAN_RTR(config-voiceport)#no shut
    PSTN_IP-WAN_RTR(config-voiceport)#exit
    PSTN_IP-WAN_RTR(config)#voice-por
    PSTN_IP-WAN_RTR(config)#voice-port 0/0/1:15
    PSTN_IP-WAN_RTR(config-voiceport)#no shut
    PSTN_IP-WAN_RTR(config-voiceport)#exit
    PSTN_IP-WAN_RTR(config)#voice-port 0/2/1:23
    PSTN_IP-WAN_RTR(config-voiceport)#no shut
    PSTN_IP-WAN_RTR(config-voiceport)#exit
    PSTN_IP-WAN_RTR(config)#
    PSTN_IP-WAN_RTR(config)#
    PSTN_IP-WAN_RTR(config)#
    PSTN_IP-WAN_RTR(config)#do sh voice port summ
                                               IN       OUT
    PORT            CH   SIG-TYPE   ADMIN OPER STATUS   STATUS   EC
    =============== == ============ ===== ==== ======== ======== ==
    0/0/0:15        01  isdn-voice  up    dorm none     none     y
    0/0/0:15        02  isdn-voice  up    dorm none     none     y
    0/0/0:15        03  isdn-voice  up    dorm none     none     y
    0/2/0:23        01  isdn-voice  up    dorm none     none     y
    0/2/0:23        02  isdn-voice  up    dorm none     none     y
    0/2/0:23        03  isdn-voice  up    dorm none     none     y
    0/0/1:15        01  isdn-voice  up    dorm none     none     y
    0/0/1:15        02  isdn-voice  up    dorm none     none     y
    0/0/1:15        03  isdn-voice  up    dorm none     none     y
    0/2/1:23        01  isdn-voice  up    dorm none     none     y
    0/2/1:23        02  isdn-voice  up    dorm none     none     y
    0/2/1:23        03  isdn-voice  up    dorm none     none     y
    50/0/1          1      efxs     up    dorm on-hook  idle     y
    50/0/2          1      efxs     up    dorm on-hook  idle     y
    50/0/3          1      efxs     up    dorm on-hook  idle     y
    50/0/4          1      efxs     up    dorm on-hook  idle     y
    50/0/5          1      efxs     up    dorm on-hook  idle     y
    50/0/6          1      efxs     up    up   on-hook  idle     y
    PWR FAILOVER PORT        PSTN FAILOVER PORT
    =================        ==================
    PSTN_IP-WAN_RTR(config)#

Maybe you are looking for

  • Using a for loop to populate JButton values with letters of Alphabet

    I am trying to create a column of 26 JButtons, with the text of the button being a letter of the alphabet, but I want to find a faster way to do it. I've tried using the Character class, but it won't let me use an int variable with the constructor. T

  • Links from Search Results are not resolving or take a very long time.

    The searches happen fairly quickly, but the links from the results are not resolving. I am unable to get the information I need. It appears there are performance problems with the site. Lennie

  • Can't drag, drop, or move icons from dock

    The issue exactly is that I can no longer move icons to the dock, remove them from the dock, reorder them, or delete them. The context menu still works fine, I just can't drag and drop. Furthermore, if I attempt to drag and drop from a stack, it read

  • Emptying Aperture trash doesn't remove images from library

    Not sure what's going on. Did a little house cleaning over the past few days and deleted about 2K images overall. And I emptied the aperture trash. The number of files in the program goes down. But the size of the library doesn't change. The date of

  • Network error (code 32)

    I am trying to publish a colleague's iCal calendar to our server over the network. Every is seemingly setup correctly, network connection is fully functional and admin login is correct. When I hit the publish button, I get an error message along the