NME-WAE-502 for point to point ?

Can I use two NME-WAE-502 for a point-to-point WAN, one as edge and one as core ?
Is it also possible to use them without the Central-Manager ?
Thanks !

Hello Daniele,
here are my comments:
Can I use two NME-WAE-502 for a point-to-point WAN, one as edge and one as core ?
There is no restriction where to install them but these are design mainly for branch offices, my suggestion is to give your best guess and estimate number of users, applications, bandwidth and take the time to check the design guides as well. Request assistance to your Cisco Partner too.
some details about the module:
NME-WAE-502
Max Optimized TCP Connections: 500  
Max CIFS Sessions: 120
Max Recommended WAN Link [Mbps]:4
further details can be found on the design guide
http://www.cisco.com/en/US/docs/solutions/Enterprise/Data_Center/WAASDC11.html
Is it also possible to use them without the Central-Manager ?
WAAS continues to function in the event  of CM failure, but you  need it for configuration changes, monitoring, statistics, software updates...etc.
hope that helps,
Felix

Similar Messages

  • IOS Image for NME-WAE-502

    The data sheet for the NME-WAE-502 indicates that a minimum IOS of 12.4(9)T or later must be used. Does the image have to be a T train image?
    Also, does the image have to be a particulare feature set, ie. Advanced IP Services, etc.?
    Thanks.
    John

    John,
    Yes, the NME-WAE requires a 12.4T image. Support for the NME-WAE hardware will be rolled into 12.5 mainline.
    Thanks,
    Zach

  • NME-WAE-502-K9 does not come up on 3925 router

    Hello,
    I have a 3925 ISR G2 router equipped with the following:
    NAME: "CISCO3925-CHASSIS", DESCR: "CISCO3925-CHASSIS"
    PID: CISCO3925-CHASSIS , VID: V03 , SN: FCZ151920TA
    NAME: "Cisco Services Performance Engine 100 for Cisco 3900 ISR on Slot 0", DESCR: "Cisco Services Performance Engine 100 for Cisco 3900 ISR"
    PID: C3900-SPE100/K9   , VID: V03 , SN: FOC15060R5V
    NAME: "9 Port FE Switch on Slot 0 SubSlot 1", DESCR: "9 Port FE Switch"
    PID: HWIC-D-9ESW       , VID: V01 , SN: FOC1508029Y
    NAME: "C3900 AC Power Supply 1", DESCR: "C3900 AC Power Supply 1"
    PID: PWR-3900-AC       , VID: V02 , SN: QCS1517P0BR
    The router is also equipped with the following two modules:
    NME-WAE-502-K9
    SM-NM-ADPTR which is needed to support the NME-WAE-502-K9 on 3925 ISR G2 routers.
    The issue is that both of the above modules are not showing up in "show inventory", "show version" and "show diag".
    The router is running the following IOS version:
    15.0(1)M5
    The router has the following licenses installed:
    License Info:
    License UDI:
    Device#   PID                   SN
    *0        C3900-SPE100/K9       FOC15060R5V    
    Technology Package License Information for Module:'c3900'
    Technology    Technology-package          Technology-package
                  Current       Type          Next reboot 
    ipbase        ipbasek9      Permanent     ipbasek9
    security      securityk9    Permanent     securityk9
    uc            None          None          None
    data          None          None          None
    I also tried to install the "diagk9" license for evaluation, which did not solve the issue.
    I also tried to reboot the router, also did not solve the issue.
    It seems to me, per Cisco's documentation, that the router is meeting the minimum requirements.
    Please advise if you know how to solve this issue.
    I'm attaching "show tech-support" output from the router, and also a screenshot of the rear side of the router.
    Thanking in advance, Udi Dahan.

    Hello Ehud,
    Looks like this could be hardware issue. Do you see the power on the NME module when you put it in?
    There could be two problems:
    1. The NME-WAE-502-K9 is bad. Try putting this in a different router and see if it shows up to make sure the NME module is good.
    2. The SM-NM-ADPTR is bad. Try to use different adapter with NME module and see if that shows up.
    3. The router slot itself is bad. try putting the adapter and NME module in different router to verify if it works.
    If nothing above works, you may want to open up a TAC case for RMA creation.

  • CM on NME-WAE-502-K9 ?? Is it possible??

    I do have two ISRs with this module, and would like to know if it's possible to set it up one of them as a Central Manager.
    Any ideas?

    hi there,
    the NME-WAE-502-K9 cannot be used as a WAAS Central Manager.  It is used for:
    * Edge deployments at small and medium-sized enterprise branches
    * For use with Cisco WAAS Enterprise or Transport licenses
    http://www.cisco.com/en/US/prod/collateral/contnetw/ps5680/ps6870/product_data_sheet0900aecd8058218c.html
    cheers

  • Change ACNS to WAAS in NME-WAE-502-k9

    Hi,
    Is it possible to migrate ACNS to WAAS in NME-WAE-502-K9? I only find this document http://www.cisco.com/en/US/docs/app_ntwk_services/waas/waas/v413/aow/guide/acnsvbguide.html and it is said, the image only supports WAE. If this possible, could you provide the guidance to migrate it? Thanks

    Hi,
    The procedure is the same ones as to reinstall the software. It's described in the "Maintaining your WAAS system" section of the documentation.
    To make it easier, here are the steps:
    To reinstall the system software on an NME-WAE network module installed in a Cisco access router, follow these steps:
    Step 1 Log in to the Cisco router in which the NME-WAE module is installed, and reload the NME-WAE module:
    router-2851> enable
    router-2851# service-module integrated-Service-Engine 1/0 reload
    Step 2 Immediately open a session on the module:
    router-2851# service-module integrated-Service-Engine 1/0 session
    Step 3 While the module is reloading, you will see the following option during boot phase 3. Enter *** as instructed:
    [BOOT-PHASE3]: enter `***' for rescue image: ***
    Step 4 The  rescue image dialog appears. The following example demonstrates how to  interact with the rescue dialog (user input is denoted by entries in  bold typeface):
    This is the rescue image.  The purpose of this software is to let
    you install a new system image onto your system's boot flash
    device.  This software has been invoked either manually
    (if you entered `***' to the bootloader prompt) or has been
    invoked by the bootloader if it discovered that your system image
    in flash had been corrupted.
    To download an image from network, this software will request
    the following information from you:
        - which network interface to use
        - IP address and netmask for the selected interface
        - default gateway IP address
        - FTP server IP address
        - username and password on FTP server
        - path to system image on server
    Please enter an interface from the following list:
       0: GigabitEthernet 1/0
       1: GigabitEthernet 2/0
    enter choice: 0
    Using interface GigabitEthernet 1/0
    Please enter the local IP address to use for this interface:
    [Enter IP Address]: 10.1.13.2
    Please enter the netmask for this interface:
    [Enter Netmask]: 255.255.255.240
    Please enter the IP address for the default gateway:
    [Enter Gateway IP Address]: 10.1.13.1
    Please enter the IP address for the FTP server where you wish
    to obtain the new system image:
    [Enter Server IP Address]: 10.107.193.240
    Please enter your username on the FTP server (or 'anonymous'):
    [Enter Username on server (e.g. anonymous)]: username
    Please enter the password for username 'username' on FTP server:
    Please enter the directory containing the image file on the FTP server:
    [Enter Directory on server (e.g. /)]: /
    Please enter the file name of the system image file on the FTP server:
    [Enter Filename on server]: WAAS-4.4.1.10-K9.sysimg
    Here is the configuration you have entered:
    Current config:
              IP Address: 10.1.13.2
                 Netmask: 255.255.255.240
         Gateway Address: 10.1.13.1
          Server Address: 10.107.193.240
                Username: username
                Password: *********
         Image directory: /
          Image filename: WAAS-4.4.1.10-K9.sysimg
    Attempting download...
    Downloaded 15821824 byte image file
    A new system image has been downloaded.
    You should write it to flash at this time.
    Please enter 'yes' below to indicate that this is what you want to do:
    [Enter confirmation ('yes' or 'no')]: yes
    Ok, writing new image to flash
    .................................................................................. done.
    Finished writing image to flash.
    Enter 'reboot' to reboot, or 'again' to download and install a new image:
    [Enter reboot confirmation ('reboot' or 'again')]: reboot
    Restarting system.
    Step 5 After the module reboots, install the .bin image from an HTTP server:
    NM-WAE-1# copy http install 10.77.156.3 /waas WAAS-4.4.1.10-k9.bin
    Step 6 Reload the module:
    NM-WAE-1# reload
    After the module reboots, it is running the newly installed WAAS software.
    I hope this helps
    Daniel

  • NME-WAE-502-K9 & RME

    The NME-WAE-502-K9 shows as an unknown device type in RME. The SysObjectID returns as .1.3.6.1.4.1.9.1.1210; however, the RME supported device table says it should be 1.3.6.1.4.1.9.1.823. I have confirmed the device credentials are correct. The inventory & config archive are working. What do I need to do to ensure RME recognizes the NM correctly?

    Hi Drew,
         Very interesting.  I'm actually working with another customer at present who has both nme-wae-502 and nme-wae-522 devices, and both of these are returning sysObjectID 1.3.6.1.4.1.9.1.823 (ciscoNmWae) , which according to the LMS 3.2 Supported Devices documentation is correct - http://www.cisco.com/en/US/docs/net_mgmt/ciscoworks_lan_management_solution/3.2/device_support/table/lms32sdt.html.
    In my investigation of this other problem I did come across 1.3.6.1.4.1.9.1.1210 (ciscoNmWae502) & 1.3.6.1.4.1.9.1.1211 (ciscoNmWae522) but couldn't explain why the different sysObjectID's
    From my customer I see :
    Cisco Wide Area Application Services Software Hardware Version: nme-wae-502-4.0.23.4
    Cisco Wide Area Application Services Software Software Release 4.0.23 (build b4 Apr 20 2009)
    AND
    Cisco Wide Area Application Services Software Hardware Version: nme-wae-522-4.1.3a.32
    Cisco Wide Area Application Services Software Software Release 4.1.3a (build b32 Jun 18 2009)
    You are seeing :
    Cisco Wide Area Application Services (WAAS-UNIVERSAL-K9) Software Release 4.2.1 (build b38 Jun 16 2010)
    Version: nme-wae-502-4.2.1.38
    So what I think has happened here, is that in the later release of WAE software that you are running, the new sysObjectID's have been introduced to uniquely identify the nme-wae-502 and nme-wae-522.  Unfortunately these new sysObjectID's are not recognised by LMS/RME hence it's showing as an Unknown device type in RME.
    I'll need to lodge a request to have support for these new sysObjectID's added to LMS.  Not sure how long this will take before it becomes available though.
    Derek

  • NME-WAE-502-K9 doesn´t want to boot

    Hi.
    I have added a new NME-WAE-502-K9 in one of our remote Cisco 2811 routers. This module doesn´t boot, and it seems to be in a loop trying to boot. I´m trying to find documentation about how to proceed with this kind of situations and this kind of network modules, but don´t find anything helpful. Please, could you give me a help?
    router #service-module integrated-Service-Engine 1/0 status
    Service Module is Cisco Integrated-Service-Engine1/0
    Service Module supports session via TTY line 66
    Service Module is failed
    Service Module heartbeat-reset is enabled
    Service Module is in fail open
    Service Module status is not available
    [Resuming connection 1 to 1.1.1.1 ... ]
    ServicesEngine boot-loader>
    ServicesEngine boot-loader> reboot
    Rebooting !ÿNmi Npx0 Dly P92 Sha0 Kbd0 Cmos Pci Dma0 PrtB Tim Exp Rfsh Geom
    Initializing memory.  Please wait. Mem0 Mem1 Ebda Sha1 CacheE Admgr1 Memmgr1 Adm
    grEbda Media LowBios Brd2 Cache0 Driver PostDrv Dma1 Irq1 Vec Brd4 Time0 Kbd1 Sp
    eed Com Vid0 Par PciEnum Vid1 Redir Brd6 Com KbdBuf SMM
    General Software Firmbase[r] SMM Kernel 1.3.2 Feb 11 2005 11:51:07
    Intel(R) E7320 Performance Development Platform
    EIST: Enhanced Intel Speedstep Driver, V3.0.
    EIST: Copyright (C) 2003-2006 General Software, Inc.
    EIST: Built Mar  3 2006, 14:49:27
    UsbHid Pwd Msg0 Msg1 Cache1 Mem2 Prot Cache2 Flg Siz0 Msg2 Ata Dsk Npx1 Apm Err
    Dbg Enb App MemReduce MemSync1 Ext MemSync2 PciRom MemSync3 Setup Time1 Mfg Brd8
    Com Admgr2 Cfg Brd10
    DDR2 Memory 1023 MB with ECC detected
    Intel(R) Celeron(R) M processor         1.00GHz
    BIOS ISE 5.00, Build date: 05/05/06
    System Now Booting ...
    Force to boot from Primary Boot Loader ...
    704 832 968 1040 1172 1184 1196 1208 1220 1228 1240 1260 1276 1288 1304 1320 133
    2 1348 1368 1380 1644 1784 2060 2204 2344 2860 3376 3640 3904 4168 RSA decrypt r
    eturned:33
    a2f9b14f5b559e31560726525c22077b
    Booting from Secure primary boot loader..., please wait.
    [BOOT-ASM]
    Please enter '***' to change boot configuration:
    got meta list size: 2, 23, 70, 244
    file opened: (hd0,1)+1, -1, -1
    file closed: (hd0,1)+1
    file opened: (hd0)1+255, -1, -1
    file closed: (hd0)1+255
    Unable to boot imageÿNmi Npx0 Dly P92 Sha0 Kbd0 Cmos Pci Dma0 PrtB Tim Exp Rfsh
    Geom
    Initializing memory.  Please wait. Mem0 Mem1 Ebda Sha1 CacheE Admgr1 Memmgr1 Adm
    grEbda Media LowBios Brd2 Cache0 Driver PostDrv Dma1 Irq1 Vec Brd4 Time0 Kbd1 Sp
    eed Com Vid0 Par PciEnum Vid1 Redir Brd6 Com KbdBuf SMM
    General Software Firmbase[r] SMM Kernel 1.3.2 Feb 11 2005 11:51:07
    Intel(R) E7320 Performance Development Platform
    EIST: Enhanced Intel Speedstep Driver, V3.0.
    EIST: Copyright (C) 2003-2006 General Software, Inc.
    EIST: Built Mar  3 2006, 14:49:27
    UsbHid Pwd Msg0 Msg1 Cache1 Mem2 Prot Cache2 Flg Siz0 Msg2 Ata Dsk Npx1 Apm Err
    Dbg Enb App MemReduce MemSync1 Ext MemSync2 PciRom MemSync3 Setup Time1 Mfg Brd8
    Com Admgr2 Cfg Brd10
    DDR2 Memory 1023 MB with ECC detected
    Intel(R) Celeron(R) M processor         1.00GHz
    BIOS ISE 5.00, Build date: 05/05/06
    System Now Booting ...
    Force to boot from Primary Boot Loader ...
    704 832 968 1040 1172 1184 1196 1208 1220 1228 1240 1260 1276 1288 1304 1320 133
    2 1348 1368 1380 1644 1784 2060 2204 2344 2860 3376 3640 3904 4168 RSA decrypt r
    eturned:33
    a2f9b14f5b559e31560726525c22077b
    Booting from Secure primary boot loader..., please wait.
    [BOOT-ASM]
    Please enter '***' to change boot configuration:
    got meta list size: 2, 23, 70, 244
    file opened: (hd0,1)+1, -1, -1
    file closed: (hd0,1)+1
    file opened: (hd0)1+255, -1, -1
    file closed: (hd0)1+255
    Unable to boot imageÿNmi Npx0 Dly P92 Sha0 Kbd0 Cmos Pci Dma0 PrtB Tim Exp Rfsh
    Geom
    Initializing memory.  Please wait. Mem0 Mem1 Ebda Sha1 CacheE Admgr1 Memmgr1 Adm
    grEbda Media LowBios Brd2 Cache0 Driver PostDrv Dma1 Irq1 Vec Brd4 Time0 Kbd1 Sp
    eed Com Vid0 Par PciEnum Vid1 Redir Brd6 Com KbdBuf SMM
    General Software Firmbase[r] SMM Kernel 1.3.2 Feb 11 2005 11:51:07
    Intel(R) E7320 Performance Development Platform

    Hi Nicolas, thanks for your response. Your suggested procedure is fine for NME-WAE. However I think our NME-WAE is crashing before to reach BOOT-PHASE3 as described in procedure, so I don´t know if i have to go ahead with sysimg images. Anyway, I have been testing with diferent sysimg versions, and I always obtain the same result: I obtain "corrupted netboot image" error
    ServicesEngine boot-loader> show config|
    IP addr:                1.1.1.9
    Netmask:                255.255.255.0
    TFTP server :           1.1.1.1
    GW IP addr:             1.1.1.1
    eth int:                external
    Default boot:           chainloader
    Bootloader Version:     2.1.15.22
    Bootloader Name:        WAAS_BOOTLOADER
    Default Helper-file:    waas-4.4.5d.5-k9.sysimg
    Default bootloader:     secondary
    External i/f media:     copper
    ServicesEngine boot-loader> boot helper/
    Invalid signature hdr
    imgaddr[0]: 0x67, g
    imgaddr[1]: 0x31, 1
    imgaddr[2]: 0x64, d
    imgaddr[3]: 0x31, 1
    imgaddr[4]: 0x78, x
    imgaddr[5]: 0x0,
    imgaddr[6]: 0x0,
    imgaddr[7]: 0x0,
    imgaddr[8]: 0x0,
    imgaddr[9]: 0x0,
    imgaddr[10]: 0x0,
    imgaddr[11]: 0x0,
    imgaddr[12]: 0x0,
    imgaddr[13]: 0x0,
    imgaddr[14]: 0x0,
    imgaddr[15]: 0x0,
    imgaddr[16]: 0x2, 
    imgaddr[17]: 0x0,
    imgaddr[18]: 0x0,
    imgaddr[19]: 0x0,
    imgaddr[20]: 0x64, d
    imgaddr[21]: 0x2>, .
    imgaddr[22]: 0x6>, n
    imgaddr[23]: 0x0,
    imgaddr[24]: 0x??????98, ˜
    Corrupted netboot image  detected ServicesEngine boot-loader> boot helper/
    Invalid signature hdr
    imgaddr[0]: 0x67, g
    imgaddr[1]: 0x31, 1
    imgaddr[2]: 0x64, d
    imgaddr[3]: 0x31, 1
    imgaddr[4]: 0x78, x
    imgaddr[5]: 0x0,
    imgaddr[6]: 0x0,
    imgaddr[7]: 0x0,
    imgaddr[8]: 0x0,
    imgaddr[9]: 0x0,
    imgaddr[10]: 0x0,
    imgaddr[11]: 0x0,
    imgaddr[12]: 0x0,
    imgaddr[13]: 0x0,
    imgaddr[14]: 0x0,
    imgaddr[15]: 0x0,
    imgaddr[16]: 0x2, 
    imgaddr[17]: 0x0,
    imgaddr[18]: 0x0,
    imgaddr[19]: 0x0,
    imgaddr[20]: 0x64, d
    imgaddr[21]: 0x2>, .
    imgaddr[22]: 0x6>, n
    imgaddr[23]: 0x0,
    imgaddr[24]: 0x??????98, ˜
    Corrupted netboot image  detected
    any idea?

  • NME-WAE-502-K9 configuration question

    Hi,
    It is not clear to me from the configuration guide how we configure WCCP using WAE-502 module which is embedded on the 2811 router, and especially the concept of subinterfaces. I understand when the WAAS is an external appliance connected to the router, but what happens when the card is embedded?
    Any help would be greatly appreciated.

    You configure the interface for the integrated service module as a normal interface on the router (Ip addresses, etc.). Then you configure the NME's IP address and the default gateway from the router. Then you should be able to ping the device, and you can either session into the module from the router or telnet directly to the device like an appliance.
    A very helpful guide is posted here...
    http://www.cisco.com/en/US/docs/app_ntwk_services/waas/waas/v403/module/configuration/guide/wsnmecfg.html
    Hope that helps,
    Dan

  • NME-WAE-502 wccp config example?

    I have a branch deployed with an appliance using WCCP and I just purchased a module for a smaller site. I am having trouble equating my appliance wccp config over to the module. Read all the white papers but I am missing something really simple.
    In the appliance deployment I have a subinterface on my router with a dedicated segment for the appliance (lets say .1 on the router and .5 on the appliance)
    On the module I am not able to give the IN 1/0 interface an IP on the same segment as my subinterface, hence my confusion. none of the documents I have read really address the config to that level of detail (IP schemes)
    I have given the module a dummy IP and its configured other than the fact that im not sure how to IP it vs the router to get the traffic to flow properly.
    a config example would be greatly appreciated.
    Thanks,
    -Scott

    Here is the router using wccp with the appliance, see if this looks okay.
    ip wccp 61 redirect-list 111
    ip wccp 62 redirect-list 111
    interface Multilink1
    bandwidth 3072
    ip address x.x.x.x 255.255.255.252
    ip wccp 62 redirect in
    no peer neighbor-route
    ppp chap hostname p1672490-1810058
    ppp multilink
    ppp multilink group 1
    ppp multilink fragment disable
    service-policy output wanQOS
    interface GigabitEthernet0/0
    description DATA
    ip address 10.75.121.3 255.255.255.0
    ip helper-address 10.60.6.119
    ip wccp 61 redirect in
    ip flow ingress
    duplex auto
    speed auto
    standby 0 ip 10.75.121.1
    standby 0 priority 110
    standby 0 preempt
    interface GigabitEthernet0/0.74
    description waas
    encapsulation dot1Q 74
    ip address 10.74.121.2 255.255.255.0
    ip helper-address 10.60.6.119
    ip wccp redirect exclude in
    ip flow ingress
    standby 0 ip 10.74.121.1
    standby 0 priority 110
    standby 0 preempt
    interface GigabitEthernet0/0.76
    description VOICE
    encapsulation dot1Q 76
    ip address 10.76.121.3 255.255.255.0
    ip helper-address 10.60.6.119
    ip wccp redirect exclude in
    ip flow ingress
    standby 0 ip 10.76.121.1
    standby 0 priority 110
    standby 0 preempt
    access-list 111 deny   ip 10.60.200.0 0.0.0.255 any <--callmanager segment
    access-list 111 deny   ip 10.76.0.0 0.0.255.255 any
    access-list 111 permit ip any any

  • Nme-wae not registering with CM

    I am using version 4.1.3.55 and when I try to enable cms on the nme-wae-502 it shows the message bellow, what is strange is that when I put version 4.0.17 with the same config then it registered with CM with success. But I need the 4.1.3 working on it, I have other wae's with same version working fine just one with this issue.
    (config)#cms enable
    Registering WAAS Application Engine...
    Sending device registration request to Central Manager with address X.X.X.X
    Failed to contact CDM X.X.X.X(TIMEOUT). Please check connectivity with CDM device and status of management service on CDM.
    register: Registration failed(512).
    cms: unable to register node
    FAILED to enable management services

    Hi Dstol,
    i also have problem like that, my device success pinged the CM but failed to register. I try to execute command cms database delete, and also re enable cms, but shown error like :
    Registering WAAS Application Engine...
    Sending  device registration request to Central Manager with address xxx.xxx.xxx.xxx
      Failed to contact CDM xxx.xxx.xxx.xxx (Unmarshaled: 9001). Please check connectivity with CDM device and status of management service on CDM.
    register: Registration failed(512).
    cms: unable to register node
    FAILED to enable management services
    Can You Help me ?

  • How to trun off batch determination for certain shipping points ?

    During Delivery Notes creation we would like to turn off the batch determination on basis of certail shipping points. can some please guide what is the best way to do it. We do not want it turned off for all the shipping points but for a special ones.
    The idea is when we create Delivey for certain shipping point we do not need to fill in the batch code and yets save, pick confim, goods issue during delivery creation process....
    we have sepcial shipping points for consignment process and for them we need to skip the batch determination......
    Thanks in advance
    Rajey

    I don;t think you  can control based on shipping point because batch creation is controlled at movement type level

  • Can I show a data label for only one point in a series?

    Forgive a newbie question from an Excel convert, but can I show a value label for only one point in a data series? If yes, how?
    There are a number of graphs where I only want to value of either an extreme value or the ending value to show. Having all the labels in a series makes the chart too busy. This is pretty easy to do in Excel.
    If this can't be done, I guess that adding a text box over those points would work.
    Thanks

    Hi W-T,
    Welcome to Apple Discussions and the Numbers '09 forum.
    wahoo_tiger wrote:
    Forgive a newbie question from an Excel convert, but can I show a value label for only one point in a data series? If yes, how?
    Sure. Here's and example labeling only the MIN and MAX points.
    Column B contains the data charted with the blue line.
    Column C extracts the MIN and MAX values using the formula below. Those two values are charted as a separate series, using the green data point markers, and are labeled with their values. The intervening empty string values appear to have doused the lines connecting the two data points.
    Formula: =IF(OR(B=MAX(B),B=MIN(B)),B,"")
    Regards,
    Barry

  • When i open terminal i get (login(1685,0x7fff73770960) malloc: *** error for object 0x106d2c4d0: pointer being freed was not allocated *** set a breakpoint in malloc_error_break to debug  [Process completed])

    so all of a suddun i open terminal and i get
    login(1685,0x7fff73770960) malloc: *** error for object 0x106d2c4d0: pointer being freed was not allocated
    *** set a breakpoint in malloc_error_break to debug
    [Process completed]
    in the terminal window any help?

    Launch the Console application by entering the first few letters of its name into a Spotlight search, and look under "User Diagnostic Reports" for crash logs related to "login." Select the most recent one and post the contents -- the text, please, not a screenshot.

  • Projectname.exe' does not contain a static 'Main' method suitable for an entry point .

    Hi,
    I'm developing a blog reader for windows 8 store app. It was perfectly worked before. But because of some miss behave my coding i get below error. No other errors there.
    Error    1    Program 'c:\Users\.........\Desktop\Blog_Reader\Blog_Reader\obj\Release\intermediatexaml\Blog_Reader.exe' does not contain a static 'Main' method suitable for an entry point    C:\Users\..........\Desktop\Blog_Reader\Blog_Reader\CSC  
     Blog_Reader
    Please help me to figure this.
    Thank You!

    Go to your App.Xaml and R-Click Go to Properties
    Check whether the Build Action is ApplicationDefinition
    If not change it to ApplicationDefinition. Clean the code (solution ) and Deploy..
    Chears....

  • Solution for Windows Store app "projectname.exe" does not contain a static 'Main' method suitable for an entry point . Error.

    Hi,
    I'm developed a blog reader for windows 8 store app. It was perfectly worked before. But suddenly it started to miss behave and I got an
    error. No other errors were there other than that.
    Error 
    Program c:\Users\.........\Desktop\Blog_Reader\Blog_Reader\obj\Release\intermediatexaml\Blog_Reader.exe' does not contain a static 'Main'
    method suitable for an entry point. 
    C:\Users\..........\Desktop\Blog_Reader\Blog_Reader\CSC    Blog_Reader
    But I found the solution while I fixing it.
    Solution for that is like below.
    Go to your App.Xaml and Right-Click thenGo to Properties
    Check whether the Build Action is
    ApplicationDefinition
    If not change it to ApplicationDefinition.
    Clean the code (solution) and Deploy
    Now the error is fiexed.

    Hi Robana, 
    Good sharing on the Technet. 
    This will definitely benefit other who may encounter the same issue as yours.
    Thanks for your sharing again. 
    Kate Li
    TechNet Community Support

Maybe you are looking for

  • Performanc​e issues - CVI 2010

    Hi all, I have code I've compiled on a development machine - XP Pro with SP3 - and I'm seeing some performance issues on a similarly configured test machine.  2GB Ram, Pentium 4 CPU 2.8GHz.  I had our IT person clean off another machine for me to use

  • How do I use Time Capsule as an external hard drive?

    How do I use Time Capsule as an external hard drive? I want to remove photos & music from my laptop and store them in Time Capsule only.

  • How can I say an Application "Push that button"?

    Hi all, I have set up a script to launch an application, and this works. But the application opens and waits for the user to push the button "AVVIO" ("Start") to run. I would like to tell the application, through the script, to push that "Start" butt

  • How can I Embed Video

    I'm trying to create an application that allows a user to combine several types of media files into one swf file that can then be passed around and viewed elsewhere. How can I embed a video into the swf file? It won't work if you just use the Embed k

  • Reinstalling CS4 on new mac

    Hi, I am having several problems reinstalling CS4 Design premium on my new mac with Mountain Lion. Time machine backup reinstall didnt work I kept getting licensing no longer works 150:30 error. So I contacted Adobe and they told me I had to reinstal