No access after changing Interface Settings

Hello Everyone!
Let me start by saying that i am quite new to cisco equipment.
I have a new Cisco SF 300-24 and try to configure a static VLAN.
I changed die Administrative PVID for a few ports from 1 (Default-VLAN) to 10 (my new VLAN is Static) in Interface Settings.
Now I can't ping from my PC to the Switch on the ports I have changed.
Any help would be appreciated,
Thanks!
Jürgen

Based on your description I can only assume that the management IP for your switch is configured on the default vlan 1.
If you want to be able to access the switch from both vlan 1 and vlan 10 you will need to configure a router with access to both vlans. Alternately if you want to access the switch on vlan 10 only you will need to change the management vlan on the switch.
Sent from Cisco Technical Support iPhone App

Similar Messages

  • Satellite Pro L40 wont boot after changing BIOS settings

    Alright changed a few settings in the bios last night and now when I boot I get a black screen lights flash and that hard drive light comes on but nothing on screen.
    There was no password on bios,... how would I reset BIOS to normal?
    I put a windows disk on I can hear the disk spinning but nothing on the screen
    (I think I have come to the right place on the forum)
    Its a Toshiba Satellite Pro L40 model psl4be.
    Thanks

    >There was no password on bios,... how would I reset BIOS to normal?
    You can set the BIOS to default ONLY inside the BIOS so you have to access the BIOS pressing F2 or at the beginning of the booting order
    But I doubt that this problem is related to the BIOS.
    Maybe its just a simple bad luck that this issue happened just exactly after changing something in BIOS.
    Try to connect an external monitor and check if you can see something on 2nd display.

  • T43p-blue screen after changing display settings

    Display turned blue after changing resolution obviously to some wrong settings, how to revert the process when cannot see anything but the start up sequence?

    go into the safe mode and change the resolution, or at least reinstall the driver. Press F8 during initial startup of the laptop. 
    Regards,
    Jin Li
    May this year, be the year of 'DO'!
    I am a volunteer, and not a paid staff of Lenovo or Microsoft

  • Tecra A3 does not work after changing power settings

    I changed my power settings in my tecra a3 laptop and now it won't start properly. wants to start but just keeps going back to press F2 or F12 please help.

    Hi,
    where did you changed them? In the BIOS or in the Toshiba HW-setup?
    I would suggest you to go to the bios after powering up your machine. You must just hit F2 ant then in the bios search for the setting "setting everything to default" or something with "bios setup defaults" to reset your bios settings.
    After that your machine should boot up again.
    Greets

  • No video after changing audio settings

    Just got my atv2 and was working fine through HDMI cable.  I was in settings and changed audio setting to 16 or some other number and when i turned atv2 back on i get apple logo as normal but when it should start I cant see anything on screen and white led on atv2 flashes once approx every 10 seconds and then atv2 restarts after every 5 minutes or so.  Please help have I changed HDMI setting or something?

    Surely some one can help.  I've tried it on another TV and same thing happens except screen flashes green every now and then.

  • ITunes and App store access after changing Apple ID.

    Having changed country of residence recently, I changed my Apple ID. However, the old ID continues to come up on my iPad and asks me for my password. The ID has been closed and it will not accept either my old password or my new password under the new ID. It does work on my PC under the new Apple Id, but I cannot access, download or update any apps etc on my iPad.
    When attempting to access the Apps Store it constantly comes up with a log-in using my old ID and will not et me change that ID. If I try to change the password using "Forgot password", it simply will not recognise the old ID as being a valid ID. The email address for the old ID is no longer valid or in use and that is why I chnaged my Apple ID rather than setting up a new ID.
    Any help greatly appreciated
    Old Silva

    Hi , 
    Welcome to the Apple Support Communities!
    I am sorry to hear that you cannot connect to or download from the iTunes and App Stores. There are some very good troubleshooting steps that I would recommend in this situation. Please follow the steps and information in the article below. 
    Can't connect to the iTunes Store
    Troubleshoot issues on an iPhone, iPad, or iPod touch
    If you haven't been able to connect to the iTunes Store:
    Make sure your date, time, and time zone are correct in Settings > General > Date & Time. 
    Note: Time Zone may list another city in your time zone.
    Make sure that your iOS software is up to date by tapping Settings > General > Software Update (iOS 5 or later) or connecting your iOS device to iTunes and clicking Check for Update on your device's Summary page.
    Check and verify that you're in range of a Wi-Fi router or base station. If you're on a device with cellular service, make sure that cellular data is turned on from Settings > General > Cellular.
    Note: If connected to cellular data, larger items may not download. You may need to connect to Wi-Fi to download apps, videos, and podcasts.
    Make sure that you have an active Internet connection. You can check the user guide for your device for help with connecting to the Internet.
    Make sure that other devices (portable computers, for example) are able to connect to the Wi-Fi network and access the Internet.
    Try resetting (turning off and then on again) your Wi-Fi router.
    If the issue persists, try troubleshooting your Wi-Fi networks and connections.
    Have a great day, 
    Joe

  • Monitor says VIDEO MODE NOT SUPPORTED after changing display settings

    HELP! I am about to have a nervous breakdown with my mac mini! I hooked up the mac to my Philips LCD via DVI. No problem at all. But because the screen is only 15" I wanted to play around with the display settings a bit. So I changed the resolution from it's original 1204x768 to the one higher (not sure of numbers) and to my HORROR, I now can't get any picture at all - it says "VIDEO MODE NOT SUPPORTED". I have tried everything I can think of. I have rest the P-RAM, I have unplugged all cables, plugged the back in again, I bought the mac into work and hooked it up to my monitor and changed the resolution back to 1024x768 which is what it was on originally and that STILL didn't work. I can see the Apple logo and then it goes black and comes up with the error message. HELP! What am I doing wrong - I can't believe one click of a mouse button has rendered my display useless!!!

    Welcome to Apple Discussions!
    Try booting the mini without the display connected, and then, once the system is running, connect the display. This will often force the system to default to a low resolution, and then correctly detect the display when it is connected.
    If that doesn't help, with the display connected, boot into safe mode (hold the shift key down when starting up) and once the system is running, change the resolution to 1024x768, and ensure the correct refresh rate is selected. Rebooting normally ought then to give you a good display.
    If all else fails, boot into safe mode with the display connected, and then in the Finder's file menu, use the 'find' option to search for 'windowserver' (no quotes). You should get 2 or 3 results, including one with a string of alphanumeric characters. Move all of them to the trash and restart normally.

  • After changing some settings I have to log in everywhere all the time!

    HELP! I followed the advise of Mozilla Support and changed some (privacy) settings because I kept having trouble with Adobe Flash Player that wouldn't run.
    Now I have to log in EVERY TIME on my email and other accounts, even if I've told them to 'remember me'
    I want to change that back again, but don't know where and how!

    To be more precise, if you are use "Clear history when Firefox closes":
    *do not clear the Cookies
    *do not clear the Site Preferences
    *Tools > Options > Privacy > Firefox will: "Use custom settings for history": [X] "Clear history when Firefox closes" > Settings
    *https://support.mozilla.org/kb/remove-recent-browsing-search-and-download-history
    Note that clearing "Site Preferences" clears all exceptions for cookies, images, pop-up windows, software installation, passwords, and other website specific data.
    Clearing cookies will remove all specified (selected) cookies including cookies with an allow exception that you would like to keep.

  • .GIF playing slower even after changing "Delay" settings..

    Hey guys,
    So I rendered out a sequence of 10 files in a 3D software, brought them into Fireworks and created .gif. It worked fine, played smoothly.
    Then I added layout elements, text, etc from Photoshop. Then I rendered it again.. and every time I do it plays slow, like the delay setting is enabled.. but it's at 0. I played it in both a browser and Windows Picture Viewer - same result. I tried turning it to the default 7 delay, to 1, etc. Every time it's the same result.
    The preview before it renders plays smoothly too! I just don't understand...
    I updated to the latest service release of Fireworks.
    Anyone know what's going on? I'd appreciate any help.
    Thanks!

    Can you post here the Fireworks PNG file, because I presume, if you try to create an animation in Fireworks, you work inside an editable Fireworks .png file?
    After we see the PNG, we'll be able to help, maybe!
    Creating Fireworks simple GIF animations is easy, in general. Default is, indeed, "7", when you specify how long each State will play, which means 7/100 of a second. You should not lower this to a number less than 7, from my experience.
    I have myself created quite a few GIF animations in the past (AJAX preloder GIFs, mostly), and Fireworks has always worked fine for me!

  • WRT54G v8: Unable to change some settings via the browser interface

    I have a WRT54G V8 router which I'm trying to set up as a wireless access point.
    I purchased it some time ago and flashed the firmware to version 8.00.2. I see there
    is a newer firmware version available, and I'm going to try flashing that to see if it
    helps, but wanted to ask here first.
    The problem is that when I connect to the router using a web browser, I can see
    the administration pages, and even change most settings, but some settings
    just snap back to their previous values.
    For example, I go to Setup -> Advanced Routing, and change Operating Mode
    from Gateway to Router. When I do, I see it changes to Router, then I see it
    talking to the HTTP server, and then it changes back to Gateway.
    This also happens in other areas, like trying to enable MAC address filtering -
    it won't let me enable it, and the Security Mode setting (under Wireless -> Wireless
    Security) - It won't let me select WPA2 Personal, among others.
    Note that I've had this router for a while, but decided to change how it was configured
    today, so I started by pressing and holding the reset button for >5sec to reset it to
    factory defaults and went from there.
    I'm assuming there must be some settings which are preventing these from taking,
    but I can't imagine any setting which should prevent me from enabling the MAC
    address filtering.
    Just in case this matters, I have the router connected to my in-home network using
    one of the 4 Ethernet ports, and don't have anything plugged into the Internet port.
    Also, I have turned off the DHCP server, and assigned a static IP address to the
    router. This is the IP I'm using to connect to the router's administrative pages via
    a browser running on one of the other PCs on my in-home network.
    The wireless access point is working, in that I can connect to my in-home network
    with my wireless client (laptop). 
    Can anyone help me understand what I'm doing wrong?
    Thanks,

    Thanks, Yes, I did reset the router. Just to clarify:
    - I was having the problem where making changes to some settings would cause the settings to revert back to the original settings. In fact, the settings would switch back before I would have a chance to click on the Save Settings button. Clicking on the button after the settings changed back, of course, saved the original setting. For example, I would click on a drop-down control to change a setting, see the browser communicate with the HTTP server, then the drop-down would just snap back to the original value. It wouldn't allow me to change it to a different value.
    - I reset the router, including holding the reset button for >5 seconds to force a full-reset. This didn't help.
    - I attempted to update the firmware with the latest version for my router (yes, I double-checked that I had the correct version for my router/version). This failed with a strange message and required that I do another reset of the router.
    It was after this failed attempt at the update that the problem went away. Now, I am able to change these particular settings and the changes stick.
    At this point, I updated the firmware to the latest version and it worked. After this, I am still able to make all the necessary setting changes and the router is performing as I need.
    Thanks for all the help,

  • Interface getting failed after changing the Business system to that service

    Hello All,
    Our Env... is XI 3.0 and this is related to produciton env.
    Based on our client requirment to change the business system from client 871 to 100 for  one of the R3 system which is reciever type(rfc).
    After doing all the necessary changes , that particular service is getting failed and in the CC monitoring for that service I can see the log as "RFC_ERROR_LOGIN_FAILURE" mandate 871 (earlier client) does not exist in  the system.
    The steps which I have followed to change the Business system.
    1>I loged into the SLD of PRD system and clicked on businsess landscape .then i have clicked on the specified system to be changed (RY1 ) and then clicked on change mode and selected the required client (100) and saved the settings.
    2>I have logged into ID(Integration Directory) and selected the service (RY1) which need to be changed .Under service -->Adaper specific -->compare sld configurations and then clicked on apply changes.
    3>Now selected that communication channel of service (RY1) RFCRecieverR3 and changed the client 871 to 100 and the password of user XIRFCUSER ...
    Then i saved the changes and after that i have activated that interface.
    After that when i logged into CC monitoring and viewed that service channels and see the following errors:
    Receiver channel 'RFCReceiverR3' for party '', service 'RY1'
    Error can not instantiate RfcPool caused by:
    com.sap.aii.af.rfc.RfcAdapterException: error initializing RfcClientPool:com.sap.aii.af.rfc.core.repository.RfcRepositoryException: can not connect to destination system due to: com.sap.mw.jco.JCO$Exception: (103) RFC_ERROR_LOGON_FAILURE: Mandante 871 não existente no sistema (selecionar mandante existente)
    Can any one help me out of this situation , and i need to fix this ASAP as this is production system.
    Awaiting for your reply.
    Best Regards
    Rakesh Reddy

    Hello Nisar
    Thanks for the update,
    Let me say few points  about this particular problem:
    1>The interface "XX" from XI sends data to two systems( R3 -->RP1 & RY1), some thing like branched (same data is passed to both the reciever systems).
    And the second RY1 is copy of First system RP1 (Production sys) which is used for data loading purpose and every week there will be a refresh from First sys (RP1) to Second(RY1).
    2>Now the first sys(RP1) is recieving the data successfully from XI , and the second one (RY1) is getting failed .And this started after changing the Business system 871 to 100 .
    3>As mentioned by you , I have checked all the points mentioned
        i)In SM59 for XI (ABAP part) two rfc's are maintained (LCRSAPRFC & SAPSLDAPI) and the test connection is also fine...But I did not find these two connections in reciever systems(RP1 & RY1 too).
       ii)In reciever system RY1 ,when i went to RZ70 , i did not noticed any special settings and SLD Bridge :Gateway Information is not maitained over there .and the same thing in other reciever system(RP1) , with this can we confirm that there is nothing wrong in RZ70 settings.
       iii)In SLDAPICUST at recievers end for both systems nothing is mantained , where as in XI system all the details are maintained(Host name,port, user & password).
    I have translated the error log into english from the CC monitoring for this interface which is in portuguese language .
    It says that:
    RFC_ERROR_LOGON_FAILURE: 871 Mandante not in the system (select principal existing)
    Kindly advise me what to do ..for fixing this problem(this is pretty urgent and it is production env...)..
    If any information required , I can provide that.
    Best Regards
    Rakesh Reddy

  • After changing yahoo mail pswd i cannot access mail on my iPhone

    After changing my yahoo mail pswd I cannot access mail on my iphone.  All other apps work and I can get mail on my macbook and ipad.  For my iphone I get an error message "cannot connect to server".  What is wrong?

    happened to me this morning, I just went into mail, settings, and then deleted one of the yahoo accounts listed there, not sure how it set up twice, maybe b/c cloud or the restore I did.

  • TS2621 I can access yahoo mail from safari but not from the iphone ipad mail icon after changing password

    I can access yahoo mail from safari but not from the iphone ipad mail app after changing my password

    Go into your settings and remove the account. Add the account again with your new password.
    Best of luck- K.

  • How do you access updates to apps from the App store after changing to a new ID because the password on the old ID was changed and you don't know what it is now?

    How do you access updates to apps from the App store after changing to a new ID because the password on the old ID was changed by the former husband and you don't know what it is now?  And you set up your own new ID and account but can NOT access the updates, from the App store for the many apps that you already have, because they require that you sign in with that former now inaccessible ID and account and password?  Call it a problem of modern times and changing relationships, if you want to be charitable.

    So I guess it will only be new apps that I download that are allowed to give me their updates while 13 updates wait for me on an ID I can no longer access.
    Yes...  sorry.
    In the future, if need be, you can re download your purchases for free  >  Downloading past purchases from the App Store, iBookstore, and iTunes Store
    Good rule of thumb is to back up your purchases regardless  >  Mac App Store: Backing up your app purchases

  • After latest update, Itunes will not open unless I allow itunes to change screen settings on my laptop. How do I stop this?

    I have upgraded to the new version of Itunes 11.1 and everytime I try to open it it asks me to allow changes to be made to my computer. If i click yes it changes my screen size to 64bit so I cant see half the page. If i change the settings back to normal it works until shut down itunes and the reverts back to odd settings. If i click no it will not open at all. Ive tried uninstalling and reinstalling but same thing keeps happening. Can anyone help me please?

    Is iTunes endlessly saying "Accessing iTunes Store"? Or is something a bit different going on?

Maybe you are looking for