"No Audio Device Available" - Vi
My uncle bought the external sound blaster assuming it would work with windows vista, since it says this on the box... however as it turns out the disc doesnt carry the correct drivers... anyway, i've downloaded and installed these onto his laptop, and they all appear in mmsys.cpl with the heading "working properly" ... however, when I try to open creative smart recorder i'm told there is no audio device available, and the creative diagnostic says that hardware has not been detected, despite the fact that it is plugged into a USB port and the power light on the SB box is on. Has anyone else had this problem and figured out how to solve it's I've tried different combinations of inputs and had no luck and am running out of ideas. Also, when I play cassettes from the hi-fi, plugged into the line in on the sound blaster, then plug headphones into the phones jack, there is no output from that either. Any possible help that can be offered is much appreciated?thanks - dan
I've recently had the same trouble and still haven't solved it.
I have the "li've 24" usb soundblaster which worked fine on my previous computer running on Windows XP home. When I connected it to a new PC using Vista 32 bits it "created" all manner of problems, all of which I eventually resolved apart from the inability to use the smart recorder. It gives an error message that it can't find a device, which is obviously stupid as everything else works. I have tried running this part of the application in Windows XP compatibility mode but it makes no difference. I have virtually given up trying unless someone out there knows of a solution. As things are, it's a real nuisance not having this facility.
Similar Messages
-
No audio devices available in late-2013 iMac
Updated Mavericks to 10.9.1 yesterday.
Today there are no analog audio devices available for output. Airplay devices work normally.
I have reset PRAM, disconnected all peripherals etc. Have tried connecting audio devices to the 3.5mm output jack.
Any suggestions?
Thanks in advance.This issue was resolved by re-installing 10.9 over 10.9.1.
Think I'll wait for 10.9.2 until I update again. -
E5 DAC/Amp Win8 error "There is no supported audio device available"
I've just received my Sb E5, and installed the software package (while the E5 was connected and charging) without "apparent" problems. However, if I start the software it will report a problem with reading the device, and if I use the menu and select "audio device selection" it will immediately report"
"There is no supported audio device available"
If I disconnect, the software's volume indicator will max, and then if I reconnect USB the volume will return to ~15%.
Please advise ...
TIAHave you installed all of the drivers:
http://www.msi.com/product/mb/Z77A-G45.html#/?div=Driver&os=Win7%2064
I don't see anything about the Sound Blaster Cinema
http://www.msi.com/product/mb/Z77A-G45.html#/?div=Overview
Did you mean the z87-g45 gaming? http://www.msi.com/product/mb/Z87-G45-GAMING.html -
Smart Recorder - Audigy 2 ZS - Win 7 - "no audio device available"
LSmart Recorder - Audigy 2 ZS - Win 7 - "no audio device available"nI've got Windows 7 Ultimate 64 bit and a Creative Audigy 2 ZS. They've worked fine together, but I recently tried to install the programs that come on the CD and I can't get Smart Recorder to work.
It has a message saying "There is no audio device available on the system. The application will now close."? I checked my control panel and it definitely shows a my Audigy 2.
I found an old post that suggested using the CTZAPXX.EXE on the CD, but it didn't do anything. I watched the CPU go to 50% usage, but nothing happened for minutes. (http://forums.creative.com/t5/Sound-Blaster/Speaker-settings/m-p/40229)
How can I fix this problem with Smart Recorder?
Thanks,
MikeIs it time to upgrade to X-Fi or another brand?
-
"No supported audio device available" ?
Win7, Creative board is: sound blaster X-FI Extreme Gamer.
Creative Consule shows the subject message whenever i try to open it. The creative player would show the same message but i re-installed it and it works fine.
Trying re-install the driver gives the old "device not found" message. In device manager there are no problem devices found. It shows the creative card and 2 High definition audio devices as "Working".
These are the driver/programs I am presently running:
CMPlyr5_PCAPP_LB_5_25_02.exe
CSL_PCAPP_LB_2_6_09.exe
DDL_PCAPP_LB__3_00_-6.exe
DTS_PCAPP_LB__03_08.exe
SBXF_PCDRV_LB_2_8_003.exe
Under Sound (Playback) I have the Speakers, Creative SB-XFi set as the default.
For recording I have Digital-In Creative SB-XFI as the default.
The music/videos plays just fine using any player that i have.
Problem is: No supported audio device available. How do i correct this and have a working console?
thank you,
savagclI am no expert, but does it help by installing it with an admin account in windows?
(As opposed to any non-admin user accounts.) -
Console Launcher No support Audio Device Available
Note: Creative SB X-fi is detected (without a yellow mark) in my device manger. My card is an X-fi Titanium Fatalty Professional.
The easiest way I can put this is by explaining the mistake I made. Without installing the card, I moved it from one PCI-e slot to another, the one below it. This caused a small annoying issue that I decided to fix by totally uninstalling the card (correctly I hope) and putting it back in it's original slot. After reinstalling it via the disk it came with, when the computer restarts afterwards I am told that no supported hardware is detected and most of what seems to have installed correctly doesn't even show in my programs.
I have tried uninstalling and driver sweeper for HOURS straight over and over and so far nothing is working. Has anyone had a similar issue or know what the problem is? I've already made sure I'm using the same settings I originally used before moving slots but no dice.
P.S. During SOME of the updates or even installations, I? occasionally receive the error I-00 (usually during Alchemy or Creative Control Console installations or Updates) and I am told the installation can't continue. It does though, simply bypassing these things/
I am using Windows 7 64bitUpdate: I'm facing a new issue now during installation! -EVERY- time the install wizard finishes and I restart the computer, I see the volume panel icon on the task bar and Creative SB X-fi when I hover over it. However, when I double click to open the console launcher (Which installed correctly to my knowledge) I'm told no supported audio device is available.
Did I break my card or something after what I did earlier? Or is my disk screwed up now too? I'd really rather not use the motherboard's crappy audio, I can actually tell that the audio quality is lower. -
TS1574 no audio is working on imac and no audio device available to choose from
I am receiving no audio out of my IMac and no option to choosing the internal speakers device. Any thoughts would be appreciated. Originally thought is might have been a virus but down loaded software and no fix to solution.
Thanks,Take each of the following steps that you haven't already tried.
1. Start with the steps recommended in this support article.
2. If your model has an audio-out (headphone) port, and a red light is coming from it, the internal switch is stuck in the position for digital output. You may be able to free it by inserting and removing a mini-stereo jack of the proper size. Inserting any kind of tool in the port may cause damage that won't be covered by your warranty.
If there's no red light, the switch may still be stuck in the headphone position. Try to free it the same way.
3. Boot in safe mode. You don't have to log in; just reboot as usual when the login screen appears.
4. Reset the NVRAM.
5. Reset the SMC.
6. Reinstall OS X after backing up all data.
7. Make a "Genius" appointment at an Apple Store. -
http://www.emu.com/support/vista.asp
Driver & Firmware update download link:
http://www.emu.com/support/files/dow...cy=&Platform=1
MAC drivers & firmware update:
http://www.emu.com/support/files/dow...cy=&Platform=2
jutapamaiki wrote:
Jutapa wrote:
Hmm... maybe you didn't open the page(s) there before postinghere?
As stated there:
E-MU® 0202 / 0404 / Tracker Pre USB Web Install Package v1.3
Date: 2/1/2008
Size: 69.8 MB
------------------------------------------end quote-----------------
My reply:
What???? Why do you suppose I didn't open that page? If I didn't open that page, how could I have quoted from it?
As I quoted in my previous post, as you quoted in your reply above, the drivers on that page are listed as "Tracker Pre". (Excuse me, but I don't know how I could have known that it was described as such on that page, if I had not even opened that page? Strange assumption on your part, if I may say so!)
In any case, I asked you (or anyone who knows) what that designation "Tracker Pre" means. (Pre Beta?) That certainly does not sound like a final version. Especially considering that the driver of 4/23/2007 is also still listed on that page, it really does not look like the driver of 2/1/2008 is "final", full (non-beta) driver.
So, why does the title of this thread describe the driver at the linked page as being "Final"?
Please explain.
And please, do not make silly assumptions, that I did not visit a page, when it should be quite obvious that I had done just that. Thank you.
Message Edited by maiki on 02-26-200811:44 PM
LOL
Tracker Pre is just another audio interface model E-MU has recently prepared ...
jutapa -
Re: "There is no supported audio device available"
Thanks for both the comments. I had looked all through the various BIOS settings, but hadn't gone into the OC area, because I'm not over-clocked. When my wife gets off her computer, I'll go into the BIOS and take a look at the Execute Disable Bit setti...
Just... why resurrect old topic? Open new thread if you require help.
>>Please read and comply with the Forum Rules.<< -
How do I use 2 Core Audio devices at the same time in Logic w/out switching
Hello, I use the Aardvark Direct Mix usb3 as my audio interface for mic and guitar. I just upgraded to Logic Pro 7 today and was hoping someone could tell me how I could use the Built-in Audio Core Audio driver along with the Direct Mix USB Core Audio Driver at the same time without having to switch Core Audio Driver's and than rebooting Logic. It is very frustrating doing that as well as not being able to hear my Logic audio during playback/record mode when I am trying to record via the USB3. WHat can I do? Thanks! If ther are both core audio, why can I not just use both of them at the same time? Why must a switch back and forth? Thanks!
[email protected]THanks everyone! awsome article! Thanks for posting it, nh!
The weird thing is, once I go up to the Menu and select Open Aggregate Device Editor in the AUDIO/MIDI setup utility and try to add a new Aggregate Device setup (step # 6 from the link), the only audio device available is the "Built-in Audio". What's weird is when I have the main Audio MIDI Setup utility open, every single drop-down menu/tab has the "Direct Mix USB 3 1.0.9.1" device right beneath the "Built-in Audio" option. To me that says that the core audio device is indeed recognized by my computer (obviously since I can record with it using Logic). Can anyone help me with this one? Any suggestions?
Not that it should matter but, the hardware audio interface that I am using is made by the no-longer-existant company once known as Aardvark. I actually had to purchase a third party Core Audio driver just to have it recognized by OS X.
This is the website where I purchased my audio driver :
http://www.usb-audio.com/
A little more on how this device and it's core audio driver function within Logic . . . (Hopefully this might clarify something I may be screwing up) . . .
I launch Logic with its default Built-in Audio which allows playback of audio from the app. I than go up to Audio Hardware and Drivers and than drop the flip down Driver menu down to the second option, "Direct Mix USB 3 1.0.9.1." Logic than prompts me that I should try to (re)launch Logic Pro to load the appropriate CoreAudio.. I do that. Now I am ready to record guitar through the Direct Mix USB3, I just can't hear anything (unless I use head phones as an output from the Direct Mix).
Anyway, you all probably already knew what I meant so explaining that was pointless. But my question is, if the Driver is obviously recognized by my comp in both the Audio MIDI Setup and in Logic, than why won't the Direct Mix device show up as a possibility for setting up an aggregate device? Any suggestions? Thanks!
Power Mac G5 Dual 2.7Ghz 4.5gigs of RAM Mac OS X (10.4.7)
Power Mac G5 Dual 2.7Ghz 2.5gigs of RAM Mac OS X (10.4) -
No Digital Output available in Playback devices (USB audio device)
If one has USB audio device with coax/toslink out, with proper drivers (like ie TurtleBeach Micro Advantage) available & installed then Digital Output is available to select in Playback devices. (and one can play AC3/DTS to external amplifier with ie
VLC or MPC-HT with AC3Filter DS filter)
But some USB devices (ie Phonic Digitrack -
http://www.phonic.com/en/digitrack.html ) do NOT come with drivers (as Windows has default build in). Digitrack uses TI
Burr-Brown USB Audio Codec 2906 -
http://www.ti.com/product/pcm2906
Sadly these Windows drivers do NOT have a clue about what the device actually has as inputs/outputs
So even it had coax digital out & the sound IS send via it, the actual data send is in right way, not recognized/played correctly by Digital Amplifier (AC3/DTS)
Does anybody know of a hack to make Digital Out available?
SebHi,
Generally speaking, An Audio Device do need more driver besides USB driver to make itself work properly. In terms of your situation, USB driver is not enough to make your Audio Device works properly. I think S.Sengupta
is right. Actually it would be better to contact Digitrack support to confirm its product compatibility with Windows 7.
Roger Lu
TechNet Community Support -
Audio Stream Recorder - Error: Audio device is already being used by another prog
I realized that Audio Stream Recorder is does not "work" through server list feature. So I am simply trying to use the manual method of adding URL's to the interface. However regardless of the type of stream, shoutcast, windows media or real audio, I receive the error "audio device is already being used by another program". Does anyone know how to fix this? I have closed my audio application etc to no avail. <RANT WARNING> I was very excited about using this application when I read about it. However an application that provides none of the stated features is not an application, its false advertising, since it clearly states on the box, help files and website this products "features". Anyway, it'ss very disappointing. Also, does anyone know what the supported steaming formats are, the help file say the application requires RealONE and Windows Media Player but does not mention audio stream formats? Thanks you in advance for any help.
I have the same issue. I updated to the latest software, to no avail. My first suspicion is that some Microsoft patch caused this, but I cannot verify this.
Apparently no one at Creative is very interested in this issue. -
Hi There,
I hope someone can help me. I have been struggling with NO AUDIO problem for last 4 weeks. Intially I had a big red cross in front of voice control button. I had to reformat and installed original softwares using recovery.
Now audio is available when system first boots but disappears within 5 minutes. Sometimes it does randomly come back and other times the whole device disappears and red cross appears again infront of volume control.
I have installed Audio drivers from HP site. I have also used microsoft FIX IT. Which does fix it but as soon as you restart the voice goes within 5 minutes. I have also used HP healthceck and Norton system dyognostic to check for any issues.
PC is clean as it is fully formated and only HP original OS softwares are installed + Windows updates.
I suspect that windows update may be responsible for the loss of sound but don't know which update and how to resolve.
Please help
Many Thanks in advance
Message Edited by HPdv6618ca_edmo on 10-02-2009 12:58 PM
Message Edited by HPdv6618ca_edmo on 10-02-2009 12:59 PM
Message Edited by HPdv6618ca_edmo on 10-02-2009 12:59 PMHi There,
I am facing same issue. Please tell me how did you solve your problem??
Please reply
Gaurav
[email protected]
HPdv6618ca_edmo wrote:
Hi There,
I hope someone can help me. I have been struggling with NO AUDIO problem for last 4 weeks. Intially I had a big red cross in front of voice control button. I had to reformat and installed original softwares using recovery.
Now audio is available when system first boots but disappears within 5 minutes. Sometimes it does randomly come back and other times the whole device disappears and red cross appears again infront of volume control.
I have installed Audio drivers from HP site. I have also used microsoft FIX IT. Which does fix it but as soon as you restart the voice goes within 5 minutes. I have also used HP healthceck and Norton system dyognostic to check for any issues.
PC is clean as it is fully formated and only HP original OS softwares are installed + Windows updates.
I suspect that windows update may be responsible for the loss of sound but don't know which update and how to resolve.
Please help
Many Thanks in advance
Message Edited by HPdv6618ca_edmo on 10-02-2009 12:58 PM
Message Edited by HPdv6618ca_edmo on 10-02-2009 12:59 PM
Message Edited by HPdv6618ca_edmo on 10-02-2009 12:59 PM -
Macbook Air no longer recognizes external audio devices
My Macbook air's audio port recently stopped recognizing external devices such as speakers and headphones.
The external devices are functional with other devices and fully plugged in, but only the internal speakers will produce sound.
This problem happened just recently with audio devices that had been working fine with the laptop before. I did not use any
audio devices that I haven't used with the computer before. They are fully plugged in, and I've already tried twisting the head
of the cord to see if it's going bad. The headphones I tried to use work fine with my iPhone.
I've tried opening System Preferences > Sound, to select the device, but it doesn't show up in the device list.
The internal speakers work fine, and continue to work even though the headphones or external speakers are plugged in, and in
the case of the external speakers, turned on.
Does anyone know if updating my audio driver would help?
Has anyone expirienced and resolved this problem or a similar problem?
Does anyone know how I can actually get in touch with someone who works at apple without having to go in to their store, as
I don't have time to do that and wouldn't be able to leave my laptop for repair since I use it for college?
Any help would be greatly appreciated!
Thanks so much!
Update:
I've tried using "Audio MIDI Setup", the external devices do not seem to be recognized by the computer.Because something has gone wrong. I have no way of knowing what, and without backups, you're in a very bad situation.
If you want to preserve the data on the startup drive, and it's not already backed up, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data, you can skip this step.
There are several ways to back up a Mac that is not fully functional. You need an external hard drive to hold the backup data.
1. Start up from the Recovery partition, from Internet Recovery, or from a local Time Machine backup volume (option key at startup.) Launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.” The article refers to starting up from a DVD, but the procedure in Recovery mode is the same. You don't need a DVD if you're running OS X 10.7 or later.
2. If Method 1 fails because of disk errors, and no other Mac is available, then you may be able to salvage some of your files by copying them in the Finder. If you already have an external drive with OS X installed, start up from it. Otherwise, if you have Internet access, follow the instructions on this page to prepare the external drive and install OS X on it. You'll use the Recovery installer, rather than downloading it from the App Store.
3. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
4. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data. -
*FIXED* No sound and 'No Audio Device' in Control Panel. *FIX
I?m having a problem with my sound. Basically all I get is a system sound, which means no sounds from itunes but the error prompt sounds still play. I?m tempted to say that this is a detection issue because of several things:
-First, when looking in the ?sounds and audio devices? in the control panel I get grayed out selections and a ?no audio device?.
-Secondly, when running the directX diagnostic tool (typing ?dxdiag? in the ?run? window) I get several troubling indications. First under device I have no manufacturer or product ID. Second under drivers I have (copied from dxdiag text file):
Driver Name: ctaud2k.sys
Driver Version: 5.2.000.96 (English)
Driver Attributes: Final Retail
WHQL Logo'd: Yes
Date and Size: 8//2006 4:45:38, 499584 bytes
Other Files:
Seems hunky-doorey but then I have a note at the bottom that reads:
Sound Test Result: Failure at step 3 (DirectSoundCreate): HRESULT = 0x88780078 (No driver)
I have seen another similar post that seemed to have the same problem, but they didn?t provide much information and the fix was to pull out the audio card, run start up, turn it off, and then put it back in and run start up. If this is what needs to be done, could I have a picture or something of what the sound card looks like?
This problem started when I tried to update my sound card and since then my sound has been? possessed? or prone to working at sometimes and then (most of the time)failing at others.
Here is the dxdiag.txt file without the lengthy directShow filters and directx components:
System Information
Time of this report: 5/9/2007, 2:8:45
Machine name: GURU7892COMPUTE
Operating System: Windows XP Home Edition (5., Build 2600) Service Pack 2 (2600.xpsp_sp2_gdr.070227-2254)
Language: English (Regional Setting: English)
System Manufacturer: Dell Computer Corporation
System Model: Dimension XPS
BIOS: Default System BIOS
Processor: Intel(R) Pentium(R) 4 CPU 2.80GHz (2 CPUs)
Memory: 022MB RAM
Page File: 436MB used, 2026MB available
Windows Dir: C:\WINDOWS
DirectX Version: DirectX 9.0c (4.09.0000.0904)
DX Setup Parameters: Not found
DxDiag Version: 5.03.2600.280 32bit Unicode
DxDiag Previously: Crashed in system information (stage 3)
DxDiag Notes
DirectX Files Tab: No problems found.
Display Tab : No problems found.
Sound Tab : DirectSound test results: Failure at step 3 (DirectSoundCreate): HRESULT = 0x88780078 (No driver)
Music Tab: DirectMusic test results: All tests were successful.
Input Tab: No problems found.
Network Tab: No problems found.
DirectX Debug Levels
Direct3D: 0/4 (n/a)
DirectDraw: 0/4 (retail)
DirectInput: 0/5 (n/a)
DirectMusic: 0/5 (n/a)
DirectPlay: 0/9 (retail)
DirectSound: 0/5 (retail)
DirectShow: 0/6 (retail)
Display Devices
Card name: RADEON 9800 SERIES
Manufacturer: ATI Technologies Inc.
Chip type: RADEON 9800 PRO AGP (0x4E48)
DAC type: Internal DAC(400MHz)
Device Key: Enum\PCI\VEN_002&DEV_4E48&SUBSYS_3002002&REV_00
Display Memory: 28.0 MB
Current Mode: 52 x 864 (32 bit) (75Hz)
Monitor: Plug and Play Monitor
Monitor Max Res: 600,200
Driver Name: ati2dvag.dll
Driver Version: 6.4.000.6660 (English)
DDI Version: 9 (or higher)
Driver Attributes: Final Retail
Driver Date/Size: 2/6/2006 9:50:46, 26368 bytes
WHQL Logo'd: Yes
WHQL Date Stamp: n/a
VDD: n/a
Mini VDD: ati2mtag.sys
Mini VDD Date: 2/6/2006 9:50:29, 98464 bytes
Device Identifier: {D7B7EE2-0D08-CF-B669-080AC2CB35}
Vendor ID: 0x002
Device ID: 0x4E48
SubSys ID: 0x3002002
Revision ID: 0x0000
Revision ID: 0x0000
Video Accel: ModeMPEG2_C ModeMPEG2_D ModeWMV8_B ModeWMV8_A ModeWMV9_B ModeWMV9_A
Deinterlace Caps: {6E8329FF-B642-48B-BCF0-BCB659E255F}: Format(In/Out)=(YUY2,YUY2) Frames(Prev/Fwd/Back)=(0,0,) Caps=VideoProcess_YUV2RGB VideoProcess_StretchX VideoProcess_StretchY DeinterlaceTech_PixelAdapti've
{335AA36E-7884-43A4-9C9-7F87FAF3E37E}: Format(In/Out)=(YUY2,YUY2) Frames(Prev/Fwd/Back)=(0,0,0) Caps=VideoProcess_YUV2RGB VideoProcess_StretchX VideoProcess_StretchY DeinterlaceTech_BOBVerticalStretch
{3C5323C-6FB7-44F5-908-056BF2EE449D}: Format(In/Out)=(NV2,0x323564e) Frames(Prev/Fwd/Back)=(0,0,2) Caps=VideoProcess_YUV2RGB VideoProcess_StretchX VideoProcess_StretchY DeinterlaceTech_PixelAdapti've
{552C0DAD-CCBC-420B-83C8-74943CF9FA6}: Format(In/Out)=(NV2,0x323564e) Frames(Prev/Fwd/Back)=(0,0,2) Caps=VideoProcess_YUV2RGB VideoProcess_StretchX VideoProcess_StretchY DeinterlaceTech_PixelAdapti've
{6E8329FF-B642-48B-BCF0-BCB659E255F}: Format(In/Out)=(NV2,0x323564e) Frames(Prev/Fwd/Back)=(0,0,) Caps=VideoProcess_YUV2RGB VideoProcess_StretchX VideoProcess_StretchY DeinterlaceTech_PixelAdapti've
{335AA36E-7884-43A4-9C9-7F87FAF3E37E}: Format(In/Out)=(NV2,0x323564e) Frames(Prev/Fwd/Back)=(0,0,0) Caps=VideoProcess_YUV2RGB VideoProcess_StretchX VideoProcess_StretchY DeinterlaceTech_BOBVerticalStretch
Registry: OK
DDraw Status: Enabled
D3D Status: Enabled
AGP Status: Enabled
DDraw Test Result: Not run
D3D7 Test Result: Not run
D3D8 Test Result: Not run
D3D9 Test Result: Not run
Sound Devices
Description: SB Audigy 2 Audio [CF00]
Default Sound Playback: Yes
Default Voice Playback: No
Hardware ID: PCI\VEN_02&DEV_0004&SUBSYS_00302&REV_04
Manufacturer ID:
Product ID:
Type: WDM
Driver Name: ctaud2k.sys
Driver Version: 5.2.000.96 (English)
Driver Attributes: Final Retail
WHQL Logo'd: Yes
Date and Size: 8//2006 4:45:38, 499584 bytes
Other Files:
Driver Provider: Creative
HW Accel Level: Standard
Cap Flags: 0xF5F
Min/Max Sample Rate: 4000, 92000
Static/Strm HW Mix Bufs: 64, 62
Static/Strm HW 3D Bufs: 64, 62
HW Memory: 0
Voice Management: No
EAX(tm) 2.0 Listen/Src: No, No
I3DL2(tm) Listen/Src: No, No
Sensaura(tm) ZoomFX(tm): No
Registry: OK
Sound Test Result: Failure at step 3 (DirectSoundCreate): HRESULT = 0x88780078 (No driver)
Sound Capture Devices
Description: SB Audigy 2 Audio [CF00]
Default Sound Capture: No
Default Voice Capture: No
Driver Name: ctaud2k.sys
Driver Version: 5.2.000.96 (English)
Driver Attributes: Final Retail
Date and Size: 8//2006 4:45:38, 499584 bytes
Cap Flags: 0x4
Format Flags: 0xFFF
DirectMusic
DLS Path: C:\WINDOWS\SYSTEM32\drivers\GM.DLS
DLS Version: .00.006.0002
Acceleration: n/a
Ports: Microsoft Synthesizer, Software (Not Kernel Mode), Output, DLS, Internal, Default Port
SB Audigy 2 DirectMusic Synthesizer [CF00], Hardware (Kernel Mode), Output, DLS, Internal
SB Audigy 2 Audio [CF00], Software (Kernel Mode), Output, DLS, Internal
Registry: OK
Test Result: All tests were successful.
DirectInput Devices
Device Name: Mouse
Attached:
Controller ID: n/a
Vendor/Product ID: n/a
FF Driver: n/a
Device Name: Keyboard
Attached:
Controller ID: n/a
Vendor/Product ID: n/a
FF Driver: n/a
Poll w/ Interrupt: No
Registry: OK
USB Devices
+ USB Root Hub
| Vendor/Product ID: 0x8086, 0x24D7
| Matching Device ID: usb\root_hub
| Service: usbhub
| Driver: usbhub.sys, 8/3/2004 23:08:42, 57600 bytes
| Driver: usbd.sys, 8/29/2002 03:00:00, 4736 bytes
Gameport Devices
PS/2 Devices
+ Logitech PS/2 Keyboard
| Matching Device ID: *pnp0303
| Upper Filters: L8042Kbd
| Service: i8042prt
| Driver: i8042prt.sys, 8/3/2004 23:4:36, 52736 bytes
| Driver: kbdclass.sys, 8/3/2004 22:58:32, 24576 bytes
| Driver: L8042Kbd.sys, 2/0/2004 2:47:58, 3056 bytes
|
+ Terminal Server Keyboard Driver
| Matching Device ID: root\rdp_kbd
| Upper Filters: kbdclass
| Service: TermDD
| Driver: termdd.sys, 8/4/2004 0:0:07, 40840 bytes
| Driver: kbdclass.sys, 8/3/2004 22:58:32, 24576 bytes
|
+ HID-compliant MX58 Optical Mouse
| Vendor/Product ID: 0x046D, 0xC0E
| Matching Device ID: hid\vid_046d&pid_c0e
| Upper Filters: LMouKE
| Lower Filters: LHidKE
| Service: mouhid
| Driver: mouhid.sys, 8/7/200 3:48:00, 260 bytes
| Driver: mouclass.sys, 8/3/2004 22:58:32, 23040 bytes
| Driver: LHidKE.Sys, 2/0/2004 2:48:46, 24704 bytes
| Driver: LMouKE.Sys, 2/0/2004 2:48:40, 68992 bytes
| Driver: KHALMNPR.Exe, 2/0/2004 2:45:26, 4952 bytes
|
+ Terminal Server Mouse Driver
| Matching Device ID: root\rdp_mou
| Upper Filters: mouclass
| Service: TermDD
| Driver: termdd.sys, 8/4/2004 0:0:07, 40840 bytes
| Driver: mouclass.sys, 8/3/2004 22:58:32, 23040 bytes
DirectPlay Service Providers
DirectPlay8 Modem Service Provider - Registry: OK, File: dpnet.dll (5.03.2600.280)
DirectPlay8 Serial Service Provider - Registry: OK, File: dpnet.dll (5.03.2600.280)
DirectPlay8 IPX Service Provider - Registry: OK, File: dpnet.dll (5.03.2600.280)
DirectPlay8 TCP/IP Service Provider - Registry: OK, File: dpnet.dll (5.03.2600.280)
Internet TCP/IP Connection For DirectPlay - Registry: OK, File: dpwsockx.dll (5.03.2600.280)
IPX Connection For DirectPlay - Registry: OK, File: dpwsockx.dll (5.03.2600.280)
Modem Connection For DirectPlay - Registry: OK, File: dpmodemx.dll (5.03.2600.280)
Serial Connection For DirectPlay - Registry: OK, File: dpmodemx.dll (5.03.2600.280)
DirectPlay Voice Wizard Tests: Full Duplex: Not run, Half Duplex: Not run, Mic: Not run
DirectPlay Test Result: Not run
Registry: OK
DirectPlay Adapters
DirectPlay8 Serial Service Provider: COM
DirectPlay8 Serial Service Provider: COM2
DirectPlay8 TCP/IP Service Provider: Wireless Network Connection - IPv4 -
DirectPlay Voice Codecs
Voxware VR2 .4kbit/s
Voxware SC06 6.4kbit/s
Voxware SC03 3.2kbit/s
MS-PCM 64 kbit/s
MS-ADPCM 32.8 kbit/s
Microsoft GSM 6.0 3 kbit/s
TrueSpeech(TM) 8.6 kbit/s
DirectPlay Lobbyable Apps
Age of Empires II (DX7) - Registry: OK, ExeFile: Empires2. ICD (0.4.0022.072)
Age of Empires II - The Conquerors Expansion (DX7) - Registry: OK, ExeFile: \age2_x.icd (0.07.0025.064)
Dungeon Siege 2 (DX7) - Registry: OK, ExeFile: DS2.icd ()
Dungeon Siege II Demo (DX7) - Registry: OK, ExeFile: DS2.icd ()
MechWarrior Black Knight (DX7) - Registry: OK, ExeFile: MW4x.exe (45.05.000.070)
MechWarrior Vengeance (DX7) - Registry: OK, ExeFile: MW4. ICD (.30.0004.908)
Star Wars JK II Jedi Outcast (DX7) - Registry: OK, ExeFile: jk2mp.exe ()
WDM Streaming Data Transforms:
Microsoft Kernel Acoustic Echo Canceller,0x00000000,0,0,,
Microsoft Kernel GS Wavetable Synthesizer,0x00200000,,,,5.03.2600.280
Microsoft Kernel DLS Synthesizer,0x00200000,,,,5.03.2600.280
Microsoft Kernel DRM Audio Descrambler,0x00200000,,,,5.03.2600.280
Video Compressors:
WMVideo Encoder DMO,0x00600800,,,,
WMVideo8 Encoder DMO,0x00600800,,,,
MSScreen encoder DMO,0x00600800,,,,
WMVideo8 Encoder DMO,0x00600800,,,,
WMVideo9 Encoder DMO,0x00600800,,,,
MSScreen 9 encoder DMO,0x00600800,,,,
DV Video Encoder,0x00200000,0,0,qdv.dll,6.05.2600.280
Indeo? video 5.0 Compression Filter,0x0000000,,,ir50_32.dll,5.2820.005.0058
Indeo? Video 5.2 Compression Filter,0x0000000,,,ir50_32.dll,5.2820.005.0058
MJPEG Compressor,0x00200000,0,0,quartz.dll,6.05.2600.274 9
3ivx D4 4.0.4,0x00200000,,,qcap.dll,6.05.2600.280
Cinepak Codec by Radius,0x00200000,,,qcap.dll,6.05.2600.280
DivX ;-) MPEG-4 Low-Motion,0x00200000,,,qcap.dll,6.05.2600.280
DivX ;-) MPEG-4 Fast-Motion,0x00200000,,,qcap.dll,6.05.2600.280
DivX? 6.. Codec (2 Logical CPUs),0x00200000,,,qcap.dll,6.05.2600.280
Intel 4:2:0 Video V2.50,0x00200000,,,qcap.dll,6.05.2600.280
Intel Indeo(R) Video R3.2,0x00200000,,,qcap.dll,6.05.2600.280
Intel Indeo? Video 4.5,0x00200000,,,qcap.dll,6.05.2600.280
Ligos Indeo? XP Video 5.2,0x00200000,,,qcap.dll,6.05.2600.280
Intel IYUV codec,0x00200000,,,qcap.dll,6.05.2600.280
Microsoft H.26 Video Codec,0x00200000,,,qcap.dll,6.05.2600.280
Microsoft H.263 Video Codec,0x00200000,,,qcap.dll,6.05.2600.280
Microsoft MPEG-4 Video Codec V2,0x00200000,,,qcap.dll,6.05.2600.280
Microsoft MPEG-4 Video Codec V3,0x00200000,,,qcap.dll,6.05.2600.280
Microsoft MPEG-4 Video Codec V,0x00200000,,,qcap.dll,6.05.2600.280
Microsoft RLE,0x00200000,,,qcap.dll,6.05.2600.280
Microsoft Video ,0x00200000,,,qcap.dll,6.05.2600.280
Microsoft Windows Media Video 9,0x00200000,,,qcap.dll,6.05.2600.280
XviD MPEG-4 Codec,0x00200000,,,qcap.dll,6.05.2600.280
DivX? 6.. YV2 Decoder,0x00200000,,,qcap.dll,6.05.2600.280
Audio Compressors:
WMA Voice Encoder DMO,0x00600800,,,,
WM Speech Encoder DMO,0x00600800,,,,
WMAudio Encoder DMO,0x00600800,,,,
Indeo? Audio Software,0x00500000,,,iac25_32.ax,2.00.0005.0054
Vorbis Encoder,0x00200000,,,OggDs.dll,0.09.0009.0005
IAC2,0x00200000,,,quartz.dll,6.05.2600.2749
Lernout & Hauspie CELP 4.8kbit/s,0x00200000,,,quartz.dll,6.05.2600.2749
Lernout & Hauspie SBC 8kbit/s,0x00200000,,,quartz.dll,6.05.2600.2749
Lernout & Hauspie SBC 2kbit/s,0x00200000,,,quartz.dll,6.05.2600.2749
Lernout & Hauspie SBC 6kbit/s,0x00200000,,,quartz.dll,6.05.2600.2749
IMA ADPCM,0x00200000,,,quartz.dll,6.05.2600.2749
PCM,0x00200000,,,quartz.dll,6.05.2600.2749
Ogg Vorbis (mode),0x00200000,,,quartz.dll,6.05.2600.2749
Ogg Vorbis (mode2),0x00200000,,,quartz.dll,6.05.2600.2749
Ogg Vorbis (mode3),0x00200000,,,quartz.dll,6.05.2600.2749
Ogg Vorbis (mode+),0x00200000,,,quartz.dll,6.05.2600.2749
Ogg Vorbis (mode2+),0x00200000,,,quartz.dll,6.05.2600.2749
Ogg Vorbis (mode3+),0x00200000,,,quartz.dll,6.05.2600.2749
Microsoft ADPCM,0x00200000,,,quartz.dll,6.05.2600.2749
ACELP.net,0x00200000,,,quartz.dll,6.05.2600.2749
DSP Group TrueSpeech(TM),0x00200000,,,quartz.dll,6.05.2600.2 749
Windows Media Audio V,0x00200000,,,quartz.dll,6.05.2600.2749
Windows Media Audio V2,0x00200000,,,quartz.dll,6.05.2600.2749
GSM 6.0,0x00200000,,,quartz.dll,6.05.2600.2749
Messenger Audio Codec,0x00200000,,,quartz.dll,6.05.2600.2749
Microsoft G.723.,0x00200000,,,quartz.dll,6.05.2600.2749
CCITT A-Law,0x00200000,,,quartz.dll,6.05.2600.2749
CCITT u-Law,0x00200000,,,quartz.dll,6.05.2600.2749
MPEG Layer-3,0x00200000,,,quartz.dll,6.05.2600.2749
Midi Renderers:
Default MidiOut Device,0x00800000,,0,quartz.dll,6.05.2600.2749
WDM Streaming Capture Devices:
SB Audigy 2 Audio [CF00],0x00200000,3,2,,5.03.2600.280
WDM Streaming Rendering Devices:
SB Audigy 2 DirectMusic Synthesizer [CF00],0x00200000,,,,5.03.2600.280
SB Audigy 2 Sw Synth [CF00],0x00200000,,,,5.03.2600.280
SB Audigy 2 Synth A [CF00],0x00200000,,,,5.03.2600.280
SB Audigy 2 Synth B [CF00],0x00200000,,,,5.03.2600.280
SB Audigy 2 Audio [CF00],0x00200000,3,2,,5.03.2600.280
BDA Network Providers:
Microsoft ATSC Network Provider,0x00200000,0,,msdvbnp.ax,6.05.2600.280
Microsoft DVBC Network Provider,0x00200000,0,,msdvbnp.ax,
Microsoft DVBS Network Provider,0x00200000,0,,msdvbnp.ax,6.05.2600.280
Microsoft DVBT Network Provider,0x00200000,0,,msdvbnp.ax,
BDA Transport Information Renderers:
BDA MPEG2 Transport Information Filter,0x00600000,,0,psisrndr.ax,6.05.2600.280
MPEG-2 Sections and Tables,0x00600000,,0,mpeg2data.ax,
WDM Streaming Mixer Devices:
Microsoft Kernel Wave Audio Mixer,0x00000000,0,0,,
BDA CP/CA Filters:
Decrypt/Tag,0x00600000,,0,encdec.dll,6.05.2600.280
Encrypt/Tag,0x00200000,0,0,encdec.dll,6.05.2600.280
XDS Codec,0x00200000,0,0,encdec.dll,6.05.2600.280
Audio Renderers:
CyberLink Audio Renderer for Dell,0x00200000,,0,cladr.ax,3.05.0000.2409
Default DirectSound Device,0x00800000,,0,quartz.dll,6.05.2600.2749
Default WaveOut Device,0x00200000,,0,quartz.dll,6.05.2600.2749
DirectSound: SB Audigy 2 Audio [CF00],0x00200000,,0,quartz.dll,6.05.2600.2749
WDM Streaming System Devices:
SB Audigy 2 DirectMusic Synthesizer [CF00],0x00200000,,,,5.03.2600.280
SB Audigy 2 Sw Synth [CF00],0x00200000,,,,5.03.2600.280
SB Audigy 2 Synth A [CF00],0x00200000,0,2,,5.03.2600.280
SB Audigy 2 Synth B [CF00],0x00200000,,,,5.03.2600.280
SB Audigy 2 Audio [CF00],0x00200000,2,2,,5.03.2600.280Message Edited by guru7892 on 05-20-20072:43 PM
Message Edited by guru7892 on 05-24-200705:55 PMI found that once you reinstall your sound card you need to make sure you hook everything back up correctly.
basically all you need to do is run a start up with your sound card out ofyou computer and then re-run start up with the card back in.
Maybe you are looking for
-
Hello, It may sound too easy to someone but I need to ask it anyway. I am in the middle of building Oracle RAC 11.2.0.3 on Linux. I have 2 storage and I created three LUNs in each of storage so 6 LUNs in total look in both of servers. If I choose NOR
-
I just started using Mail as my mail reader and I can't figure something out. I'm sure I'm over looking something but it's driving me crazy. After I finish reading a message, I want to read the next message but there is no arrow to take me to the nex
-
Hey! Why can't I open the apps I've been downloading with Creative Cloud??
-
Hi, Isn't there a DOS command line symbol so that when javac returns all your syntax errors you can pause the screen before it blazes by your screen and you only catch the last few syntax errors. I thought it was javac whatever.java /p, but this does
-
Oracle XML Parser validation against XML Sxhema
Hi, I am developing a program in C++ on Unix, that does parsing on an XML document. For parsing I am using "Oracle XML Parser" [using DOM API]. My question is, Can Oracle XML Parser validate xml document against an XML Schema file also? I have read i