No audio when placing video on timeline!

Ive tried creating a new sequence. I have Panasonic P2CMS Ive used the last two years. I recently started using an iMAC 3.5Ghz Intel Core i7/8 GB using Premiere Pro CC. Ive been using this system for about a month with no problems, and just today clips im attempting to import and place on timeline dont have audio track attached. Audio and video will play in the source monitor, but once I try to put it on the timeline it only has video track. I've rebooted system, and re-opened premiere and it will work for a few minutes allowing me to put clip on timeline with audio and video, then stop again.
The sequence setting is the same that I've used the past few years, up until today.

You need to ask in the program forum http://forums.adobe.com/community/premiere?view=discussions
When you go to the program forum, please give more information - PPro Information FAQ http://forums.adobe.com/message/4200840

Similar Messages

Iphone 5S IOS8 - quality of audio when taking video?

The biggest disappointment with the 5S was the TERRIBLY distorted audio when taking videos of live music or loud events. The 4S didn't feature the front mic and therefor sound was passing by perpendicular to the mic and it would not be as "hot" of a signal.
I have not one but two external mice I use when I plan*** on taking video but living in a city with tons of music I am not always prepared with an external mic. Taking video with IOS7 with the 5S is useless if the audio source is above 85db or so.
Can anyone who has upgraded IOS on the 5S confirm that they have corrected the software for the mic sensitivity for a 5S? My buddy has the 6 and his live videos of music do NOT distort.
Thanks!

Hello AudioArchist,
Does the issue of recording videos still not get any sounds? If so, take a look at the article below to troubleshoot the issue further. Now it may be hard to give the exact reason why that happened, but the article should assist with getting it fixed.
If your voice is too faint or sounds unclear using iPhone, or iPod touch
http://support.apple.com/en-us/HT203792
Regards,
-Norm G.

No audio when recording video iPhone 6 (4.7in)

I just got my 6 and love it, but I have noticed that I have ZERO audio when recording video, but rather some feedback.
I have tried rebooting and powering off/on. Nothing has worked.
Any help would be very much appreciated. I hope my phone doesn't have an issue.
Thanks,
Geoff

Nevermind, I had the back covered. Silly me to think it used the same microphone on the bottom of the phone..

All audio except phone works fine. But there is no audio when placing or receiving calls.

I have an iPhone 4 with iOS 5.
In the last 24 hours, I cannot use the phone. There is no audio when placing or receiving calls. It doesn't matter if I use speakerphone, headset speaker, or headphones. Nothing works. When I answer inbound calls, the connection is made but the caller cannot hear me. When I place calls, the connection is made but the other party cannot hear me.
All other audio works fine including Music - both speaker and headphones. It seems just the phone audio is affected.
I have plugged in (and out) earphones multiple times as I read this as a possible fix. No help. I reset network settings - no help.
Any suggestions?

Is it the phone speaker or microphone, or both? Sounds like speaker since you say speaker phone works.
What other troubleshooting have you done? I would reboot, and if that doesn't change things then I would do a reset by holding both volume buttons down at the same time until the device starts rebooting.
On BBOS there was a way to make media audio play from the phone speaker instead of the speaker phone speaker. I was thinking of that as a way to test if the problem is the speaker or the phone app, but either I've forgotten how to do that or it can't be done in BB10. If you know how to do it, give it a try (and tell me how to do it).
Next try would be a security wipe, then test before you restore data or install apps. Remember to back up first.
Last would be a clean install of the OS.
If you go as far as clean OS and still doesn't work, I would assume hardware failure.
- Ira

Audio is out of sync when placed in the timeline!!!

When I play a clip in the viewer, everything is fine, but when the clip is placed into the timeline and played in the canvas, the audio is out of sync by about half a second. I noticed that even when I view the sound waves, what I hear does not match up with where the playhead is. This is extremely frustrating and I have currently resulted to physically moving the audio to match it up, something that I do not want to do for the duration of my film.
I read in another post that the video and the audio could not be at the same level. How can you tell if the video and audio are at the same level??
I have FCE 3.5 if that makes any difference. Any help would be much appreciated!

How was this clip imported? If it was captured/ingested, did you make sure that the sample rate of the capture settings matched the sample rate of your audio? Normally FCE will give you a warning if they don't match, but it can't hurt to make sure.

No Audio When using Video Out to Firewire

I do not get any audio when I use Firewire ntsc as my video out. When I set video out to canvas playback then I get audio. I want to use print to video but I cannot because the audio will not work with Firewire. I get the image on my external monitor but not the audio. I checked to make sure and the audio was not on the recorded dvd. I cannot not use print to video with canvas playback.
My Easy Setup is Format: NTSC, Use DV NTSC DV Converter. I tried using Firewire basic and got the same results.
Please Help
Ken

The audio does not play at all from the timeline if video out is set to Firewire. To answer your question, no the audio does not play in the external monitor when playing back from the timeline when Canvas is used as the video out. However, I don't believe the converter box is the problem. The audio would play in the internal speakers when using firewire as video out but it does not.
Is there a problem with FCE 4?

Stereo audio when using video camera? Any way to do this?

Is there any way to record in stereo (2 mics) when recording video with the onboard camera? Can the 30-pin connector receive a stereo signal when videoing? (iPad3, iOS 7)

I figured it out myself so thought I'd share this for anyone else who wants to record video with the audio portion in stereo, you can do this using Sonoma Wireworks' GuitarJack2 in conjunction with a mixer. Keep in mind this isn't a portable solution at all but the resulting audio is excellent, especially in headphones so this is great for doing a video of yourself singing and playing guitar (for example) and you want to capture a good stereo audio signal. Basically, the way is works is you plug your two mics (we're talking recording style microphones with the XLR connectors) into your mixer of choice. You then run a line out of the mixer into the 1/8" audio input jack of the GuitarJack 2 (it's a stereo line-in) and the 30-pin connector goes into your iPhone/iPad. There are a couple of settings you have to make with the software for the GuitarJack but once you've done that, you can then make some videos with terrific stereo sound. You monitor the audio via the headphone jack of your mixer. If anyone knows an easier way to do the same thing, please let me know but this is the only way I've found.

A way to adjust audio when capturing video?

I transfered some video/audio and am having distortion in some audio.
The original audio does not peak and when I captured it in Premiere CS6, it is not peaking out, but when I play back, I can hear occasional distortion. The video is up at:
http://www.youtube.com/watch?v=aNNgJiZMrRA
Does this sound like it is overmodulating or is something else happening?
Is there a way to adjust audio when capturing audio or is it a straight feed? Wondering if I can lower the audio input to try to fix.
thanks in advance for your help,
Charlie

How are you capturing the content? Because in my experince premiere doesn't have a way to adjust the audio levels of what your capturing. However if you post how you are capturing the footage in more detail I might be able to help. Please tell me exactly how you have everything hooked up.
For example if you have the camera hooked straight to the computer or if you're using a capture card if so what kind. Some capture cards have audio gain settings which might be causing the issue. Also some decks and cameras have audio playback volume settings which can also cause audio to be sent to premiere louder than what it started as. So if you give more detail I may be able to offer some sort of help.
One thing you might try though to remove that distortion is too add a lowpass filter to the audio, and start off by setting the low pass filter to like 3000 and just adjust by 500 up or down from there until the distortion goes away. I've had to do this in the past with audio that's distorted before. (Although I haven't experinced the specific issue you're experincing before.) Although it will make the persons voice sound muffled it will take most of the distortion out. Which getting rid of distortion at the cost of making it sound somewhat muffled is a decent trade off if worse comes to worse and you can't get the issue figured out.

No Audio When Converting Videos For iPod

whenever i convert video files for my ipod they do not have audio. i have tried several programs, and none work. i have read other discussions about this, and found that MPEG Streamclip worked for other people, however whenever i try to convert using this program, it says "Error: Can't Prepare The Movie" Can anyone tell my why i can't convert these videos? i cannot figure it out. thanks alot.

I am not sure what you mean when you ask what the "compression formats" are.The compression formet refers the manner in which the media was encoded and, by extension, how the media must be decoded. I.e., it determines which codec (encoder/decoder or compressor/decompressor) is to be used with the media file.
If you can tell me where to find those i could tell you what they are. I can, however, play the video in itunes, quicktime, and MPEG Streamclip.Simnce the files are playable in QT, the most common place to look for codec information is in the "Show Movie Info" window following the "Format:" entry. E.g., it might say:
Format: MPEG2 muxed, 640 x 480orFormat: Apple MPEG4 Decompressor, 320 x 240, millions
AAC, Stereo, 48,000 kHz
i also am not sure if there is audio in the source file.Do you hear any audio when the original file is played? If not and there is no audio track (or "muxed") information, then there may not be any sound for you to convert in the first place.
how do i find out if it is muxed?If it is "muxed," the format entry we say so. In this case blocks of audio data and blockes of video data are interspersed in a single data stream (track). This is the normal way MPEG-1 and MPEG-2 audio/video data is synchronized. In addition, these formats commonly lose their audio content when converted using QT Pro, iTunes, iMovie, FCE, FCP, or other QT based "frame-to-frame" synchronized workflow. (In the case of MPEG-2 in MPEG Streamclip or QT, the QT MPEG-2 component must also be installed in order to convert the video data alone.)
most of my videos that won't convert for an ipod are downloaded from the internet. how can i find out if they are corrupted or incomplete?Internet files should always be considered suspect -- especially if they come from a peer-to-peer source. Messages that indicated QT cannot open an otherwise fully compatible QT format is often the best indication that there is a corruption problem or that the files were improperly closed at one point or another.
most of my videos that won't convert for an ipod are downloaded from the internet. how can i find out if they are corrupted or incomplete?Normally ypu would post them to a web site or FTP storage area and post the URL. If files were downloadedd from a particular web site (e.g., a QT movie trailer), simply post the URL for the particular web page.

Latest issue: No audio when playing video

Hello-I rolled back to version 6 and for the most part, everything is working normal again,however, there is no audio when I play video (I can hear music files).
I have tried the suggested fixes in the FAQ with no luck. I noticed that if I switch to 44.1/16bit in Quicktime preferences, I can get audio but it is stuttered.
If I go to 48/24bit, there is no audio w/ video.
Suggestions anyone?
thanks.

Is this only a problem with the sound and does the video work?
*http://helpx.adobe.com/flash-player/kb/common-problems-flash-player.html
*http://helpx.adobe.com/flash-player/kb/video-playback-issues.html
*http://helpx.adobe.com/flash-player/kb/no-video-display-flash-player.html
You can check for problems caused by a recent Flash 11.3 update and possibly downgrade to Flash 11.2 or 10.3.
*https://support.mozilla.org/kb/flash-113-doesnt-load-video-firefox
*https://support.mozilla.org/kb/flash-113-crashes
*http://blogs.adobe.com/asset/2012/06/inside-flash-player-protected-mode-for-firefox.html

No audio when playing videos

Upon downloading the latest update, I have for some reason, no audio
when playing back a video...any of them. Video is there, but no sound.
Thanks

I had the exact same issue on my Home computer with XP Home sp2--No audio in itunes
However, my work computer with XP Pro sp2 works fine with the updates.
I ended up taking the advice of some others on here and reinstalled the old version of Quick Time (7.3.1) which worked...Although I'm unable to see movie trailers with the old version...But all other videos, including the one movie that I purchased, I'm able to hear...

I have no audio when i video stuff

No audio on my videos any ideas? already reset it

This did not help anything! I have no option of a audio volume slider. You will have to be more specific. There doesn't seem to be an option anywhere to turn on the mic for recording.

How to turn off audio when scrubbing in the timeline

Hi
how do i turn off the audio whilst scrubbing in the timeline?
thanks

View>Audio Scrubbing. Uncheck it.

PAL subclip out of sync when placed on NTSC timeline?

The job: 700 adverts from PAL and NTSC from 40 U-Matics - choose 300 and make an NTSC DVD compilation.
I converted the tapes to DVCPRO50.
I created subclips for each ad on each tape.
I created a new NTSC DV timeline and placed the subclips on the timeline.
(I planned to use Nattress Standards Conversion to convert the PAL subclips to NTSC).
I noticed that the PAL clips' audio cut out early. I displayed the audio waveforms for the clip - the waveform wasn't cut off - it was in sync with the end of the clip, Final cut was playing the audio late and cutting it off to match the video.
I exported the edit (to check if there was a delay in the playback of the audio on my machine), the actual output had the audio out of sync too.
When I exported the subclip as a QuickTime movie and reimported it, placed this new PAL movie on the NTSC timeline, the cut off didn't happen.
Surely the subclip and the exported QuickTime movie should behave the same on the same timeline.
Has anyone else had this problem?
Is this a known bug in Final Cut?
G5 2x2.5GHz Mac OS X (10.4.7) FCS 5.1.1

How was this clip imported? If it was captured/ingested, did you make sure that the sample rate of the capture settings matched the sample rate of your audio? Normally FCE will give you a warning if they don't match, but it can't hurt to make sure.

No audio when clip dragged to timeline, FC Express

I'm working with an older version of Final Cut Express, 4.0.1. My video clips in the beginning of the Timeline have audio but now when I try to place new clips in the Timeline, the audio for those clips won't play...no waveforms. It does, however, play in the Clip Viewer. The clips were all captured the same way, .mov files.
Please help! Thank you.

On the left of the Timeline is the video/audio Patch Panel. They determine whether video or audio or both are entered.
If a patch Panel is dis-connected no video or audio will be entered.
Al

No audio when placing video on timeline!

Similar Messages

Maybe you are looking for