No auto answer when used with Hands Free system in Toyoya RAV 4

I can make outgoing calls using the hands free system in my Toyota RAV 4 but must manually answer all incoming calls. Is there any way to have the phone pick-up after a set number of rings..I did not have this problem with my Palm Treo 650.

I just got back from my dealer...bottom line, update works. It was a $99 charge, they ran into some issues, it was their first try at it. I brought a 2 GB usb stick with me, one I had lyling around, formated it, and let them use it. They said they could not give it back, since it would have their data on it...no big deal. Turns out, there was an issue with the USB stick I gave them, they had to go out and purchase on (not sure why they didn't have one on hand alread). I have about 8900 songs on my iPod, a few playlists. It took about 20 minutes or so to finish the loading, then when you try to use some voice commands, says you cannot do it while it's compiling songs or something to that effect. A few minuts, later, the voice commands worked. Only issue I see is that everytime I turn off the car, and get back in, it goes through the process of the load again. the 2nd time was a little quicker, but still took about 5-10 minutes, and again, had the delay of not being able to use the voice. Good luck everyone!!!

Similar Messages

Does anyone have Bluetooth failures with Mot Razr Droid Maxx using car hands free systems

Both my wife and I have Razr Droid Maxx's and are having the same problems with our respective cars. At times, the phone will drop the bluetooth connection and it will have to be rebooted at which point it will be discovered and re-connected to the car. The problem is NOT in the car, as we have a Ford Fusion and a Toyota Camry and we encounter the same problem with both.
Both phones are running Ice Cream Sandwich and we have verified all of the bluetooth settings at both ends of the connection.For some reason the phones.
The problem is particularly annoying in that, at least in the Camry, you are unable to reconnect the phone while driving, so you have to pull over and put the car in Park in order to do it.
Verizon tech support and the Verizon store have been of no help. They simply shrug their shoulders and say they have never heard of the problem.
Has anyone else had issues like this?

I use Razr HD Maxx and used to have bluetooth disconnect problems during the calls. I tried everything I could think of, all in vain. Factory-reset solved the problem only for a while. Finally, I have found that some communication apps like Viber have the nasty habit of asserting itself every few minutes during non-Viber calls and reset both the bluetooth and speakerphone state to the default mode. This causes bluetooth to disconnect or turn off the speakerphone a few minutes into every non-Viber call. If you have an app like Viber, try either freezing it or uninstalling it. Uninstalling Viber was the only permanent solution to my bluetooth disconnect problems.

Problems With Hand free system and Iphone 4

Looking at the details of other people who all seem to e having the same problems with the connectivity with audio systems, I have a state of the art Kenwood car system which keeps loosing the phone. Whats the pointy of even bothering with a phone like this 3 weeks after I got it if it's features will not work.
Will Apple accept that the phone has a fault and give me the option of getting a different phone which will do what the box says?

Update iTunes on your PC > iTunes 11.1.1 for Windows (64-bit
Then restart the PC and try restoring the iPhone.

I phone compatibility with hands free car systems

I purchased an I phone which replaced a Palm Treo 650 (verizon). It worked perfectly.When I am using my in car hands free system, the I phone Tries to work but the voices break up,especially at he beginning. When I am speaking I phone to I phone it is almost impossible to understand the conversation. I phone to land line is better.
I phone to I phone not thru the handsfree is perfect.There seems to be a compatibility problem. My device is bluetooth.

There are several threads on this subject that you can use the search function for... I suggest you make sure to mention what in-car system you are using (car make and model), since this is about the most important piece of information. Also, you might try the forums at edmunds.com that have lots of related threads organized by auto make and model. For me, my Treo 700p worked, but had some issues, with my '07 Toyota/Lexus system. The iPhone works perfectly.
Message was edited by: Chas Hulme

Does my iPhone 4 work with Hands Free Profile (HFP)?

My new car is supposed to send/receive text messages via the new fandangled stereo/navigation unit. The manual says the phone must be compatible with "Hands Free Profile (HFP)" or Message Access Profile (HFP)". Does the iPhone4 use/have this? New car is a 2012 Subaru Impreza with the Nav system.
Thanks.

It supports HFP 1.5 (see http://support.apple.com/kb/HT3647).

I have created a PDF with mp3 audio clips, the file works on PC's with audio playback (WIndows 7, 8 ) however the audio does not play when hosted on a website or an ipad/tablet computer or smart phone when used with PDF reader

I have created a PDF with mp3 audio clips, the file works on PC's with audio playback (WIndows 7, 8 ) however the audio does not play when hosted on a website or an ipad/tablet computer or smart phone when used with PDF reader

adobe42135678 wrote:
the audio does not play when hosted on a website...
When viewing in what browser?

What is the blutooth number to use to sync to a hands free system in a car?

What is the blutooth number to use to sync to a hands free system in a car?

What number? The BT passcode? It should be detailed in the Handsfree section of the Car's User Guide.
Or be displayed in the car's screen if it has one.

ExecuteNonQuery doesnt return number of rows affected when used with PL/SQL

ExecuteNonQuery doesn't return number of rows affected when used with PL/SQL but returns -1. The documentation says ExecuteNonQuery method of OracleCommand returns the number of raws affected but when used with PL/SQL, it returns -1 even the update statement successfully executes and affects multiple records with no exeptions thrown.
However, if ExecuteNonQuery is used with update sql statement in the asp.net code it returns number of rows affected correctly. Does anybody know why ExecuteNonQuery behaves like this?
I am using ODP.NET that comes with Oracle Client 11g. The version is 2.111.6.20 of ODP.NET, Oracle database server is 10g.
Marat

You can get the rowcount in the stored procedure via SQL%ROWCOUNT and then pass it out as a parameter.
For example:
SQL> create or replace procedure updatesal(v_deptno in number, v_rowsaff out number) as
2 begin
3 update emp set sal = sal * 5 where deptno = v_deptno;
4 v_rowsaff := SQL%ROWCOUNT;
5 end;
6 /
Procedure created.Cheers

Test runner freezing when used with Dynamics CRM (and other apps) - Both applications freeze and never come back...

We are trying to use test runner with dynamics CRM.
MS Dynamics CRM will freeze and will not respond (even after 10 - 15 minutes). When this happens, the test manager will either freeze or a message will apear saying "waiting for application under test".
We are not recording action recordings...This makes using test manager impossible. It happens consistently, starting with slowing the PC down (mouse moving slowly, slow to load in new screens, drop downs etc) eventually leading to the app freezing.
Tried on windows xp, windows 7 etc on various specs of pcs.

I am experiencing this same issue with
Test runner freezing when used with Dynamics CRM. I notice this was first posted in June of 2010 and so far no
resolution? I was wondering if it could be related to memory issues? Do you have any troubleshooting ideas? The
issue for me seems to be sporadic and I can't
reproduce it every time.
The message I get is "waiting on application under test".
DLM

Quicktime Player with the magic mouse, when used with a bug -

On 10.7 Lion, Quicktime Player with the magic mouse, when used with a bug …
Quicktime Player will not respond, but use the USB mouse with no problem

Message was edited by: b j t

Msi x99 gaming 9 ack does not detect capture card when using with xsplit

msi x99 gaming 9 ack does not detect capture card when using with xsplit
i install every but still it does not work.

Hi
It wasn't hard to find your motherboard version:
http://www.msi.com/support/mb/Z68AGD80_B3.html#down-bios
Since your BIOS is v20.1, it couldn't be G3
Apart from checking BIOS, you can only check motherboard or moth...

Camera is hanging when using with flash

Hi Lenovo Team,
In lenovo vibe x2, camera is hanging when using with flash.Getting "Lenovo snapit isnt responding" error and screen hanged for sometime.after that when tried to open camera "Cannt cannot to camera " error is coming till when restart the phone.
Even tried Factory reset and software update.
Please provide the solution for the above issue.
Thanks,

Hi vijayprabhu,
I just tested the X2 however am not having the issue. I set flash to always on then took a picture using SnapIt however its fine.
Please check if you have the latest firmware S125.
Check out the Community Knowledge Base for hints and tips.
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"!
X240 | 8GB RAM | 512GB Samsung SSD

N95 and Toyota Bluetooth hands-free system

On 11th March I purchased a used (55 plate) Toyota Corolla Verso and as part of the deal had the Toyota Bluetooth hands-free system installed.
Everything worked fine with my Sony K600i which has eventually given up the ghost and required replacement.
I opted for the Nokia N95 and after a short wait due to stock availability it was delivered to my home address on Friday 4th May.
My initial "very impressed" thoughts soon changed to disappointment when I tried to pair the N95 with the Toyota hands-free system...
Unlike the Sony, the phone does not automatically detect that the Toyota system is searching for it.. but I can bypass this by manually searching for other devices with the phone whilst the Toyota system is searching.
I'm then asked to input the pass code (default 1234) on the phone... which I do... and the Toyota system announces that the pairing has been successfull... connection in progress... however the phone then flashes a message stating that it is not possible to pair with the Toyota system at which point the Toyota system declares "connection failed".
I've tried numerous times now with Remote Sim on and off, deleting all paired devices and starting from scratch etc etc...
I've been and spoken to the Toyota Dealership and of course they claim that there's nothing wrong with the car kit - it worked with the phone I had when I bought the car and it's not their fault I've changed to a phone which is incompatible.
As far as I can tell, the N95 has Bluetooth 2.0 installed (so did the Sony) and I understand that this *is* backwardly compatible and as such should meet the technical requirements of the Toyota System... however the lady on the service desk at the Toyota Dealership stated that there could be other issues too, but was either not able or not willing to specify what those issues would be. She suggested that the only way they would possibly be able to do anything about it would be only if Customer Relations gave them authorisation to do so and gave me their telephone number (01737 363633).
Having spoken to Toyota Customer Relations, they simply infer that it's my fault for purchasing a phone that is not compatible - but even they declined to provide me with documentary evidence (which they claim to have) proving that it is not compatible. Instead they suggested that the only course of action I would possibly have would be to speak with the dealership.... who have of course already told me that they are not able to do anything without the say so of Toyota Customer Relations.
I get the feeling someone isn't quite telling the truth...
I figure that the only way I'm going to have any recourse with Toyota is to prove beyond doubt that the phone is compatible with the requirements of the Toyota system... according to the Toyota Bluetooth hands-free system owners manual I merely need to ensure that any desired phone supports Bluetooth hands-free profiel 0.96 or 1.0.
I've tried asking O2 - they didn't know the answer and suggested I should call Nokia.
I've called Nokia on the following numbers:
08450 545454
08700 555777
09067 547540 (premium rate £0.75 per minute)
08706 092832
08450 045555
Each without success... note that the 08706 092832 number was answered by an extremely unhelpful, arrogant lady... you can probably sense I'm beginning to get a little irate now...
I've also tried to call Nokia on 08450 045555 given to me both by the Nokia website and the arrogant lady I refer to above...
At the time of writing this post, I've had the phone to my ear ringing away for 1 hour 16 minutes and counting....
1, 2, 3, 4, 5, 6, 7, 8, 9, 10.... (Me catching my breath so as to stay calm)
Can anybody whatsoever with the slightest element of confidence tell me whether the Nokia N95 supports Bluetooth hands-free profile 0.96 or 1.0??
Any advice, assistance, stress and frustration relief would VERY much appreciated.
Regards
D.Burns-Keane

Hello again... I thought some of you may like to know that I have made some progress.
After a rediculously long time on hold with Nokia I eventually opted to hang up and call back... frustratingly I did of course get through straight away only to be told that it was actually one of their quieter days and that there was no reason (as far as the guy knew) why I should have been on hold for so long... regardless... the guy was extremely helpful.
I explained my issue in detail and he advised that as far as he knew, because the phone has Bluetooth version 2, it could/would/should be compatible.
Separately I had also emailed Club Nokia with the full details of my issue.
I had also logged an appeal with Toyota Customer Services (Head Office).
Initially Toyota's response was that technology moves so fast, specifically the mobile phone industry, that technology such as car kits etc are often left inferior. As polite as they were, they basically washed their hands of the problem putting the blame squarely at my feet for purchasing a phone that in their opinion was incompatible.
My appeals regarding viewing it as unreasonable that having only bought the car in March of this year and one part of it already being relegated to a fancy dashboard accessory that doesn't really do much apart from ignore my requests to pair with my phone, fell on deaf ears to say the least. Even though I had directed them towards this and at least one other online forum upon which other Toyota owners claimed to have had their Bluetooth system upgraded under warranty.
Then an email reply arrived from Club Nokia. It specifically stated, "this handset [Nokia N95] has a bluetooth version of 2.0 and does support the headset profile"
Of course, this prompted an immediate phone call to Toyota Customer Services again... quoting my reference number (for my earlier conversation(s) with them) and informing them of the information/clarification received from Club Nokia their tone shifted a little and I was told that they would call me back.
A couple of days later I received a phone call from Customer Services informing me that they had authorised my local dealer to upgrade the Bluetooth system under warranty.
Approximately two days later I had a phone call from the Dealer informing me that the part(s) had been ordered.
And as I sit here typing this right now, they're fitting the new system to my car.
Granted I think there's a chance both the guy I spoke to at Nokia and the emailed response from Club Nokia miss the point slightly as they appear to be relying on the fact that the phone has Bluetooth V2.0 and therefore *is* compatible... this may not necessarily be the case - somebody suggested in an earlier post that the phone is only compatible with handsfree profile 1.5...
However, if Nokia are telling me it's compatible I figured I'd quote that to Toyota and see what happened (afterall I'm not telling porkies, I'm simply passing on the info I obtained from the people who *should* know)...
I think this proves a little persistance certainly goes a long way!
(I guess I just need to test the damn thing when I get my car back later today)

Mitsubishi Fuse Hands Free System

I recently bought a Mitsubishi Lancer and upgraded to the Fuse Hands Free package as the sales person told me that it worked great with iPhone. When attempting to connect my iPhone 4 (as well as previously with a 3GS) to the hands free system through the USB port, the display continuously cycles between 'connect' and 'retry' but never connects. When attempting to play anything, the system tells me that there are 'no playable files on the device' even though there are. The USB charges the phone and I can play music via bluetooth (although not as efficiently) but it will not connect via USB and I can't use the voice controls. I have done everything I can think of: reset the phone while plugged in to the USB, reset while not plugged in, manually switch audio settings on the phone and update to iOS 4.3 all to no avail. I've spoken to Apple regarding this and I was told that it is not an Apple issue and the people from Mitsubishi have no idea what I'm talking about. Anyone else have this issue and able to come across a solution?

I just got back from my dealer...bottom line, update works. It was a $99 charge, they ran into some issues, it was their first try at it. I brought a 2 GB usb stick with me, one I had lyling around, formated it, and let them use it. They said they could not give it back, since it would have their data on it...no big deal. Turns out, there was an issue with the USB stick I gave them, they had to go out and purchase on (not sure why they didn't have one on hand alread). I have about 8900 songs on my iPod, a few playlists. It took about 20 minutes or so to finish the loading, then when you try to use some voice commands, says you cannot do it while it's compiling songs or something to that effect. A few minuts, later, the voice commands worked. Only issue I see is that everytime I turn off the car, and get back in, it goes through the process of the load again. the 2nd time was a little quicker, but still took about 5-10 minutes, and again, had the delay of not being able to use the voice. Good luck everyone!!!

HT204387 How can I transmit my iphone numbers into my car's hands free system?? I have paired the two but do not know how to transmit.

Having just moved from a Blackberry to iPhone 5C I have been trying to move my contacts into my car's Hands Free. I have paired the device but became stuck when it advised me to transmit the contact list.
How do I find instruction on how to transmit?
WRJ5

The movement of contacts from the phone to the vehicle is handled by the vehicle. There is no setting on the iPhone to move the contacts. Check the user guide for the hands free system in your vehicle. Mine does it automatically, but there is a setting in the car's system that is set by default to move them.
EDIT: I'm sorry, you can also check the phone. Go to Settings>Bluetooth and find your vehicle. Tap on the small on the right side and that should bring up another settings page, mine does. There you can check "Sync Contacts". It should then sync when you connect the phone to the vehicle, unless the vehicle also has a setting.
Message was edited by: ChrisJ4203

No auto answer when used with Hands Free system in Toyoya RAV 4

Similar Messages

Maybe you are looking for