No block device for printing

Hi......
I have installed arch linux 0.6 with cups and I not found the block device on /dev responsible for printing (like lp0 or devices on /dev/printers folder - this folder doesn't exist in my system). I already loaded the module parport_pc in the rc.conf. It doesn't work. I just created too alias in the modprobe.conf referencing this module with /dev/lp0 block device. It doesn't work too. My printer is epson C43SX and when printer is turn on, cups recognizes epson installed on the /dev/unknown-parallel0, but doesn't print anything.
Any suggestions?
Thank You for everyone that help me....
enigmabr.
PS: excuse me for my poor english[/code]

I have a similar difficulty but I am a total newbie. I have discovered that I have /dev/usb/lp0. So far, I have found my cups server is not being recognised or is not accesible to root.
Thought I would just suggest though that yours might be a usb printer, and if so that is where you look. Also I think you have to have the printer switched on.

Similar Messages

Block meant for printing invoice title is dark

Respected Gurus,
Block meant for printing invoice title is dark and tittle is not printed. I am able to get the print out right in other printer.
What could be the reason.
Regards.
Daya.

Dear All,
i changed my device type to SAPWIN, and the issue is resolved.
Daya.

Oracle VM Migrating virtual disk images to physical disks (block devices)

Hi,
For performance reasons, I'd like to migrate my .img file based virtual disks into physical partitions for VM's.
What is the safest possible way to migrate all partitions (including / partition) from a virtual disk to a block device?
Thanks,
Onur

hobeygo wrote:
What is the safest possible way to migrate all partitions (including / partition) from a virtual disk to a block device?Create block devices the same size as your .img files and then use dd to copy the contents of the .img file to the block device. Your VMs need to be offline while you do this. Once you've done this, you can use Oracle VM Manager to remove the original .img file and replace it with the physical block device copy. This is low-risk, as the .img file will still be there if the new block device doesn't work.
Keep in mind that you will need a unique block device for every .img file you have.

RAC on EMC block devices

I have finished installing a 11g RAC on RHELv5 using EMC block devices for storage.
During installation i had partitioned the disks and changed ownership to oracle:dba
However everytime i reboot the server, the block devices ownership is reverted back to root and hence CRS doesnt fails to come up. So i end up doing a manual change in ownership and permission to bring up the CRS, ASM and finally the database.
Is there any way, i can automate this?
Thanks in Advance.

You can setup this in udev permissnion file. In OEL5 it looks like:
[root@rick oracle]# tail -8 /etc/udev/rules.d/50-udev.rules
KERNEL=="sdb1", OWNER="root", GROUP="oinstall", MODE="640"
KERNEL=="sdc1", OWNER="oracle", GROUP="oinstall", MODE="640"
KERNEL=="sdd1", OWNER="oracle", GROUP="dba", MODE="640"
KERNEL=="sde1", OWNER="oracle", GROUP="dba", MODE="640"
KERNEL=="sdf1", OWNER="oracle", GROUP="dba", MODE="640"
KERNEL=="sdg1", OWNER="oracle", GROUP="dba", MODE="640"

How to Suppress the POP UP window for Print out Device

Hi All,
I have One ALV Grid report and in this report I want to SUBMIT another report which, when executes gives the POP UP window for Printer Device and sends the output to that device. if we give LOCL, sends output to Spool.
So I want to Suppress that POP UP Window and by default that POP UP window should take 'LOCL' as Printer Device.
Thanks in advance,
Helpful answer get awareded.

On the submit command is a spool parameters option.
The addition WITHOUT SPOOL DYNPRO suppresses the print dialog box that is displayed as standard when you use the addition TO SAP-SPOOL.
The addition SPOOL PARAMETERS is used to transfer the print parameters in a pri_params structure that belongs to the data type PRI_PARAMS from the ABAP Dictionary.
PRI_PARAMS-PDEST specificies the output device.

Problem in creating output device for RICOH Aficio MP 2000 PCL 5e printer

HI,
i have problem in creating a output device for the RICOH Aficio MP 2000 PCL 5e as i am unable make out which device type should be assigned and what should be given in spool server tab.
i have pinged the printer in lan and it is connecting.
when i am giving the print from new ricoh printer its going to some other old printer in network.
we are unable to get the logo of our company when we are taking print from this printer from sap level.
kindly suggest what other things has to be taken care.
regards
anil

Hi,
shall i do in development and then import the same to quality and production.
also tell me what shd i put in these tabs
version-sapsripthandling-driver
list handling-printer driver
printer character set-character set-syt character set
we can find this tab in create option of device type.
when i am trying to save its showing it has to be done on program level.
kindly reply back as it will resolve the big issue for me.
thanks
anil

Lucreate fails with: Root slice device ... for BE ... is not a block device

Hi,
I'm running lucreate on a Sol10u7 x86 system as I wanted to get it to u8 level. I installed:
SUNWlucfg
SUNWlur
SUNWluu
from u8 and then a patch: 121431-58
System is not zoned and it is on ZFS with following pools:
pool: rpool
state: ONLINE
scrub: none requested
config:
NAME STATE READ WRITE CKSUM
rpool ONLINE 0 0 0
c1t0d0s0 ONLINE 0 0 0
errors: No known data errors
pool: spool
state: ONLINE
scrub: none requested
config:
NAME STATE READ WRITE CKSUM
spool ONLINE 0 0 0
c0t0d0 ONLINE 0 0 0
This is what happens:
Creating Alternative Boot Environment..
lucreate -n s10x_u8
Checking GRUB menu...
Analyzing system configuration.
No name for current boot environment.
INFORMATION: The current boot environment is not named - assigning name <s10x_u7wos_08>.
Current boot environment is named <s10x_u7wos_08>.
Creating initial configuration for primary boot environment <s10x_u7wos_08>.
The device </dev/dsk/c1t0d0s0> is not a root device for any boot environment; cannot get BE ID.
PBE configuration successful: PBE name <s10x_u7wos_08> PBE Boot Device </dev/dsk/c1t0d0s0>.
Comparing source boot environment <s10x_u7wos_08> file systems with the
file system(s) you specified for the new boot environment. Determining
which file systems should be in the new boot environment.
Updating boot environment description database on all BEs.
Updating system configuration files.
Creating configuration for boot environment <s10x_u8>.
Source boot environment is <s10x_u7wos_08>.
Creating boot environment <s10x_u8>.
Cloning file systems from boot environment <s10x_u7wos_08> to create boot environment <s10x_u8>.
Creating snapshot for <rpool/ROOT/s10x_u7wos_08> on <rpool/ROOT/s10x_u7wos_08@s10x_u8>.
Creating clone for <rpool/ROOT/s10x_u7wos_08@s10x_u8> on <rpool/ROOT/s10x_u8>.
Setting canmount=noauto for </> in zone <global> on <rpool/ROOT/s10x_u8>.
Creating snapshot for <rpool/ROOT/s10x_u7wos_08/var> on <rpool/ROOT/s10x_u7wos_08/var@s10x_u8>.
Creating clone for <rpool/ROOT/s10x_u7wos_08/var@s10x_u8> on <rpool/ROOT/s10x_u8/var>.
Setting canmount=noauto for </var> in zone <global> on <rpool/ROOT/s10x_u8/var>.
ERROR: Root slice device </dev/dsk/c1t0d0s0> for BE <s10x_u8> is not a block device: .
ERROR: Cannot make file systems for boot environment <s10x_u8>.
Please help,
Cheers,
Tom

devfsadm fixed the issue,

How to go for print preview option for locked/blocked items in PO.

Dear all,
Can we view PO even all the line items or some items in that PO are locked or blocked, by clicking Print preview button. If not by that button, is there any other way to view locked/blocked items in Print Preview format.
Can anybody suggest me on this ?
Thanks
Hemanth

Hi,
Its not possible to see the line item in the print preview if it is blocked...
You can only display in the PO only...why do you need Print preview of blocked items??
Added on :
You can check these locked details in the EKKO and EKPO table in the SE16 tcode for the respective PO and can also download the details if req. from the same table..
Hope it helps..
Regards
Priyanka.P

Regarding callfunction for output device without a prompt for printer name.

Hi,
Is there any call function, for accessing output device, without a prompt for printer name? Can we directly execute the smart form without print popup?
Can anyone suggest me in this regard.
Thanks in advance,
Shwetha Korlepara.

Hi,
Check my code and reward points by clicking the star on the left of reply,if it helps.
*& Report ZZZ_JAYTEST1                                                *
REPORT zzz_jaytest1 NO STANDARD PAGE HEADING MESSAGE-ID zhrt.
Variable Declaration
DATA : v_form_name TYPE rs38l_fnam,
       itab TYPE STANDARD TABLE OF pa0001,
       w_ctrlop TYPE ssfctrlop,
      w_compop TYPE ssfcompop,
      w_return TYPE ssfcrescl.
SELECT * FROM pa0001 INTO TABLE itab UP TO 5 ROWS.
SORT itab BY pernr.
DELETE ADJACENT DUPLICATES FROM itab COMPARING pernr.
DATA: control TYPE ssfctrlop,
control_parameters TYPE ssfctrlop,
output_options type SSFCOMPOP.
control-preview = 'X'.
control-no_open = 'X'.
control-no_close = 'X'.
control-no_dialog = 'X'.
control-device = 'PRINTER'.
output_options-tddest = 'LOCL'.
OUTPUT_OPTIONS-TDNOPRINT = 'X'.
OUTPUT_OPTIONS-BCS_LANGU = SY-LANGU.
CALL FUNCTION 'SSF_OPEN'
EXPORTING
   USER_SETTINGS            = ' '
   OUTPUT_OPTIONS           = output_options
   CONTROL_PARAMETERS       = control
EXCEPTIONS
   FORMATTING_ERROR         = 1
   INTERNAL_ERROR           = 2
   SEND_ERROR               = 3
   USER_CANCELED            = 4
   OTHERS                   = 5
IF sy-subrc <> 0.
MESSAGE ID SY-MSGID TYPE SY-MSGTY NUMBER SY-MSGNO
        WITH SY-MSGV1 SY-MSGV2 SY-MSGV3 SY-MSGV4.
ENDIF.
output_options-tddest = 'LOCL'.
OUTPUT_OPTIONS-TDNOPRINT = 'X'.
OUTPUT_OPTIONS-BCS_LANGU = SY-LANGU.
CALL FUNCTION '/1BCDWB/SF00000066'
EXPORTING
ARCHIVE_INDEX              =
ARCHIVE_INDEX_TAB          =
ARCHIVE_PARAMETERS         =
   CONTROL_PARAMETERS         = control
MAIL_APPL_OBJ              =
MAIL_RECIPIENT             =
MAIL_SENDER                =
   OUTPUT_OPTIONS             = output_options
   USER_SETTINGS              = ' '
IMPORTING
DOCUMENT_OUTPUT_INFO       =
JOB_OUTPUT_INFO            = w_return
JOB_OUTPUT_OPTIONS         =
TABLES
    itab                       = itab
EXCEPTIONS
FORMATTING_ERROR           = 1
INTERNAL_ERROR             = 2
SEND_ERROR                 = 3
USER_CANCELED              = 4
OTHERS                     = 5
IF sy-subrc <> 0.
MESSAGE ID SY-MSGID TYPE SY-MSGTY NUMBER SY-MSGNO
        WITH SY-MSGV1 SY-MSGV2 SY-MSGV3 SY-MSGV4.
ENDIF.
CALL FUNCTION 'SSF_CLOSE'.

Solaris10 : Looking for block device drivers samples

Hi,
where can I find complete examples of block device drivers for solaris 10 ? Ramdisk driver for example.
It's for educationnal purpose.
Thanks,

OK, i got the driver now.
I tried to install it on solaris 10/sparc.
No problem at compilation, no problem at installation.
But something goes wrong when trying to mkfs the ramdisk :
# mkfs -F ufs -o nsect=8,ntrack=8,free=5 /devices/pseudo/toto@0:c,raw 1024
Can not determine partition size: No such device or address
# ls -l /devices/pseudo/toto@0:c,raw
crw------- 1 root sys 98, 0 Jun 14 03:15 /devices/pseudo/toto@0:c,raw
Any ideas ?

Encrypted block devices - loficc driver compiled for Solaris 10

Hi all,
First post, and hopefully a useful one :)
I've managed to compile the OpenSolaris loopback block device with crypto support (loficc) on my Solaris 10 system, and it appears to work.
Download available here: http://ashbysoft.com/download/loficc-sol10.tgz
Phil.

Well, much of the contents of Solaris 10 make up the base of OpenSolaris. So you could open a bug against OpenSolaris without a contract, and any fixes should eventually make their way back.
In fact, you could recompile the driver and see how it operates. The code does show the difference you report.
1603 * [4] Data is buffered in the driver and pre-acked to the application. This
1604 * is only supported in Solaris 2.5.1.(See: http://cvs.opensolaris.org/source/xref/onnv/onnv-gate.bad/usr/src/uts/common/io/scsi/targets/st_conf.c)
However my assumption is that this flag should not be necessary. If you override the DLT7000 to remove that bit, does it crater as well? I wouldn't think that the driver acknowledgments would be required for some speed here.
What application are you using to dump the data? 'dd' with a big buffer size? (dd if=/dev/zero of=/dev/rmt/0cbn bs=128k count=5000)? This bit should increase the speed if the app is especially sensitive to the acknowledgement time.
Darren

Why is my page set up drop down different from your illustration in help for printing background

''duplicate - https://support.mozilla.com/en-US/questions/830795''
The page set up drop down menu looks nothing like the illustration in help. It does not include a box to check for "print background. How do I print background

first, does it sound like I set it up correctly from what I wrote?
Yes, all sounds correct.
Second, I heard that adding a b/g AX to the network will slow everything down to b/g speeds but I have also read that simply using B/G AX's to add speakers by joining the network will not slow down the N network....which is it?
The b/g AX devices will not slow down the network unless they are actively streaming AirTunes. Even then, audio streaming does not require a great deal of bandwidth, so for the most part, the effect would be negligible. Don't worry about it.
Is my network slowed down to b/g speeds because of my speaker set up or not?
The speed on your network will depend on a number of factors..are you downloading something while copying something else? Are you simply browsing? How far is the computer from the closest wireless access point?
You can check your current available bandwidth on your local network by doing the following:
Hold down the option key on your Mac while you click on the fan shaped AirPort icon at the top of the screen. Look for the Transmit Rate number.
"g" wireless = 54 Mbps
What do you see?
Oh, and by the way, I don't know if this matters, but while the time capsule serves as the main base station, it is in bridge mode because it is plugged into a 2wire gateway router.
If the Time Capsule is in bridge mode, it cannot act as the main base station. If you want, you could think of it that way if you are using the wireless on the Time Capsule as your preferred network, but the Time Capsule is not the "main" router.
Message was edited by: Bob Timmons

Error message: "Remove USB Device from printer."

I have an HP Photosmart 309 a All-In-One. It is attached to my desktop computer, which utilizes the Windows XP system. I've owned the All-In-One for about three years. I do not use the All-In-One -- or this computer -- very much. (I mostly use my laptop.)
I have not made any changes to this computer and/or All-In-One in quite some time. This error message is new. I do not have a USB device attached to the printer. Even with the error message displayed, the All-In-One allows me to print, but it will not allow me to make a copy or scan. How do I make this error message go away? What's wrong with my All-In-One? Thank you for your help!

Hi DuckLakeSue,
I understand that you are getting an error message to 'Remove USB Device from printer'. Follow the steps provided in this link by the PrintDoc to determine if your wireless radio has failed.
I hope this helped, let me know.
Thank you,
I worked on behalf of HP.

Waiting for printer to become available

I'm on OS X 10.8.5, and have a USB printer: HP p4015dn. It used to work fine to print. All of a sudden, it shows "Waiting for printer to become available", forever, and will not print. I can successfully print to networked HP printers, but even though I've rebooted the machine, rebooted the printer several times, this one just won't print anymore. I tried creating a new queue to this printer and it pauses when it tries to connect as though it can't communicate with the printer. I've tried putting the USB cable into a different port. No good. Also, no idea if this is a coincidence or not, my Fax modem stopped working - won't send out faxes anymore. What do I do to debug this?

Yep, did all that (including resetting the printing system). I can still add new Networked printers and print to them fine, but can't print to this one USB printer (but other computers can, if I move the USB cable). I went to the printer console log and I see
E [10/Nov/2014:16:22:02 -0500] [CGI] File "/usr/libexec/cups/backend/pagesender" has insecure permissions (0100775/uid=0/gid=0).
E [10/Nov/2014:16:22:02 -0500] [CGI] File "/usr/libexec/cups/backend/pdf" has insecure permissions (0100777/uid=0/gid=0).
E [10/Nov/2014:16:22:20 -0500] [CGI] File "/usr/libexec/cups/backend/pagesender" has insecure permissions (0100775/uid=0/gid=0).
E [10/Nov/2014:16:22:20 -0500] [CGI] File "/usr/libexec/cups/backend/pdf" has insecure permissions (0100777/uid=0/gid=0).
E [10/Nov/2014:16:22:37 -0500] [CGI] File "/usr/libexec/cups/backend/pagesender" has insecure permissions (0100775/uid=0/gid=0).
E [10/Nov/2014:16:22:37 -0500] [CGI] File "/usr/libexec/cups/backend/pdf" has insecure permissions (0100777/uid=0/gid=0).
E [10/Nov/2014:16:22:55 -0500] [CGI] File "/usr/libexec/cups/backend/pagesender" has insecure permissions (0100775/uid=0/gid=0).
E [10/Nov/2014:16:22:55 -0500] [CGI] File "/usr/libexec/cups/backend/pdf" has insecure permissions (0100777/uid=0/gid=0).
E [10/Nov/2014:16:23:13 -0500] [CGI] File "/usr/libexec/cups/backend/pagesender" has insecure permissions (0100775/uid=0/gid=0).
E [10/Nov/2014:16:23:13 -0500] [CGI] File "/usr/libexec/cups/backend/pdf" has insecure permissions (0100777/uid=0/gid=0).
E [10/Nov/2014:16:23:31 -0500] [CGI] File "/usr/libexec/cups/backend/pagesender" has insecure permissions (0100775/uid=0/gid=0).
E [10/Nov/2014:16:23:31 -0500] [CGI] File "/usr/libexec/cups/backend/pdf" has insecure permissions (0100777/uid=0/gid=0).
E [10/Nov/2014:17:21:01 -0500] [CGI] File "/usr/libexec/cups/backend/pagesender" has insecure permissions (0100775/uid=0/gid=0).
E [10/Nov/2014:17:21:01 -0500] [CGI] File "/usr/libexec/cups/backend/pdf" has insecure permissions (0100777/uid=0/gid=0).
E [10/Nov/2014:17:21:18 -0500] [CGI] File "/usr/libexec/cups/backend/pagesender" has insecure permissions (0100775/uid=0/gid=0).
E [10/Nov/2014:17:21:18 -0500] [CGI] File "/usr/libexec/cups/backend/pdf" has insecure permissions (0100777/uid=0/gid=0).
E [10/Nov/2014:17:21:36 -0500] [CGI] File "/usr/libexec/cups/backend/pagesender" has insecure permissions (0100775/uid=0/gid=0).
E [10/Nov/2014:17:21:36 -0500] [CGI] File "/usr/libexec/cups/backend/pdf" has insecure permissions (0100777/uid=0/gid=0).
E [10/Nov/2014:17:21:54 -0500] [CGI] File "/usr/libexec/cups/backend/pagesender" has insecure permissions (0100775/uid=0/gid=0).
E [10/Nov/2014:17:21:54 -0500] [CGI] File "/usr/libexec/cups/backend/pdf" has insecure permissions (0100777/uid=0/gid=0).
E [10/Nov/2014:17:22:11 -0500] [CGI] File "/usr/libexec/cups/backend/pagesender" has insecure permissions (0100775/uid=0/gid=0).
E [10/Nov/2014:17:22:11 -0500] [CGI] File "/usr/libexec/cups/backend/pdf" has insecure permissions (0100777/uid=0/gid=0).
E [10/Nov/2014:17:22:29 -0500] [CGI] File "/usr/libexec/cups/backend/pagesender" has insecure permissions (0100775/uid=0/gid=0).
E [10/Nov/2014:17:22:29 -0500] [CGI] File "/usr/libexec/cups/backend/pdf" has insecure permissions (0100777/uid=0/gid=0).
E [11/Nov/2014:10:57:40 -0500] Unknown directive BrowseOrder on line 22 of /private/etc/cups/cupsd.conf.
E [11/Nov/2014:10:57:40 -0500] Unknown directive BrowseAllow on line 23 of /private/etc/cups/cupsd.conf.
E [11/Nov/2014:10:57:49 -0500] [cups-deviced] PID 71814 (pdf) stopped with status 86!
E [11/Nov/2014:10:58:02 -0500] [cups-deviced] PID 71840 (pdf) stopped with status 86!
E [11/Nov/2014:10:58:20 -0500] [cups-deviced] PID 71866 (pdf) stopped with status 86!
E [11/Nov/2014:10:58:37 -0500] [cups-deviced] PID 71887 (pdf) stopped with status 86!
E [11/Nov/2014:10:58:55 -0500] [cups-deviced] PID 71910 (pdf) stopped with status 86!
E [11/Nov/2014:10:59:12 -0500] [cups-deviced] PID 71931 (pdf) stopped with status 86!
E [11/Nov/2014:10:59:36 -0500] [cups-deviced] PID 71968 (pdf) stopped with status 86!
E [11/Nov/2014:10:59:42 -0500] [cups-deviced] PID 71987 (pdf) stopped with status 86!
E [11/Nov/2014:11:00:47 -0500] [cups-deviced] PID 72046 (pdf) stopped with status 86!
E [11/Nov/2014:11:16:10 -0500] [cups-deviced] PID 72379 (pdf) stopped with status 86!
does this mean anything to anyone?

"Waiting for printer to become available" message

Each time I try to print to my Laserjet 1300, I see a message in the print queue stating, "Waiting for printer to become available." It never processes. I delete the job, try again but the same result. Result is same for short plain text, PDF or .jpg files. However, I can print a test page directly from the Laserjet 1300 printer. Have rebooted computer and restarted printer with no effect. Am able to successfully print to my backup HP Deskjet F4180. Am using a MacBook Pro OS 10.6.6. All software updates have been made. Thoughts?
This question was solved.
View Solution.

If you are using Snow Leopard and have HP software for pre-Snow Leopard (either from a CD not marked as compatible with 10.6 or you recently upgraded to Snow Leopard and had the HP software on your Mac before you upgraded - even if you did a standard uninstall of the old software or installed new software over the top of it) you must uninstall the software using the 'scrubber' option:
Go to Applications/Hewlett Packard/ click on HP Uninstaller
Click on Continue
Highlight your device on the left pane
Hold the Ctrl, Opt and Cmd keys and click on Uninstall <<<< Scrubber Option
There will be a pop up that asks if you are sure you want to uninstall ALL hp software. (At this point, if you continue, any HP printers you have installed will need to be reinstalled)
Click Continue and let it finish
Restart your Mac
Now, run a Software Update.
Finally, reset the printing system:
- Sys Prefs, Print & Fax
- Right (control) click in the rectangle listing your printers and select Reset Printing System.
WARNING - this will delete ALL of your printers!
- Select the plus sign to re-add it. Look for the printer, select it and wait until the "Add" button becomes available. Click it.
Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
I am employed by HP

No block device for printing

Similar Messages

Maybe you are looking for