No bluetooth in my S100

Dear all,
I just bought S100 about 2 months ago, and i just found out that my S100 has no bluetooth (as i know that it should have it like i read in its specification). So, whats wrong with my S100?
Can anyone help me, please? Is there any way for me to have bluetooth in my S100? Or should i install something to it?
Thank you in advance..
Solved!
Go to Solution.

Hello Chrisiva and welcome to community,
I understand as you are missing the most convenient feature to connect the mobile devices.
Not all the models comes with Bluetooth however, you can share your netbook serial number with me in private message and I can confirm if the netbook comes with inbuilt Bluetooth device.
You can also press Fn+F5 key and check if the Bluetooth is present and disable.
You have the option for external usb Bluetooth dongle.
Best Regards,
Tanuj
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution".! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!

Similar Messages

Adesso wireless mouse doesn't work in Mountain Lion.

My Bluetooth Adesso iMouse S100 doesn't work in Mountain Lion. It barely moves and constantly halts as if its driver is continuously interrupted. It is unusable. It worked beautifully in Snow Leopard.
I don't believe the problem is in the mouse, but just for completeness the batteries are full strength. The Bluetooth control panel signal strength for the mouse ranges from -50 to -48, which may be low but I'm pretty sure was the same in Snow Leopard.
Has anyone experienced and have a fix for this problem?
Thanks.

A mouse pad solved the problem. The Ikea Lack table I'm using is the source of the problem. Its table top surface is apparently scattering the mouse's laser and not reflecting it back properly. I have not experienced this problem with any other table I've used, wood, Formica, et al.

Portege S100: Can't install Toshiba SD Host to use Toshiba Bluetooth SD Card2

I'm trying to install the Toshiba Bluetooth SD Card2 onto my Portege S100 but I can't get it to work, i get the error
"Could not open the Bluetooth ACPI device driver (tosrfec.sys). Try again?)
which suggests that the SD slot is not reading the card. I then went onto the Toshiba bluetooth section and found the driver files for the Toshiba SD Host Controller Driver (at http://aps.toshiba-tro.de/bluetooth/). I believe that I should install this as the Host Controller Driver, and not the SDA Standard Compliant SD Host Controller.
However, when i try to update the Driver, selecting specifically the folder of the Toshiba Host Controller Driver, it says that it couldn't find a better match than the one installed already. Therefore, I decided to install it manually, but instead, i get the error
"The specific location does not contain any information about your hardware"
I've run out of ideas, can anyone help me please?
Thank you
Regards
Danh

yes, thank you but
which suggests that the SD slot is not reading the card. I then went onto the Toshiba bluetooth section and found the driver files for the Toshiba SD Host Controller Driver (at
http://aps.toshiba-tro.de/bluetooth/). I believe that I should install this as the Host Controller Driver, and not the SDA Standard Compliant SD Host Controller.
However, when i try to update the Driver, selecting specifically the folder of the Toshiba Host Controller Driver, it says that it couldn't find a better match than the one installed already. Therefore, I decided to install it manually, but instead, i get the error
"The specific location does not contain any information about your hardware"
Danh

Review A2DP Bluetooth Headset Sony HBH-DS200 with Leopard 10.5.1

Hello, this is first post...
I'm sorry if my English is not perfect.
I wanted to buy a headset A2DP after discovering that the Leopard supported .... so I decided to create a mini-review.
Yesterday I bought A2DP Bluetooth Headset Sony HBH-DS200
Matching perfect
Stop / Pause link headphones perfect
Quality sound good but not perfect, but its is clear frequencies seem that the clips are (too high frequencies).
Now I wanted to try under bootcamp and see what result to arrive.
At the next update.
PS: Some of you have tried this headset or other headphones a2dp? HTC S100? As a new feature of Leopard seconds you can resolve this problem? Thank you

I just bought the SE HBH-DS220. It sounds really good when connected to itunes as well as to my W910i. I cannot hear any noticable difference between this and when I have a wired connection to the computer or phone. If you turn the volume to max on the clip it even plays a bit louder through the headphones, which is just a plus in my book as they don't distort the sound at all.

Cannot Get SD Card reader to work on Portege S100

I have a Portege S100-S213TD I recently dug out of the closet to have my daughter use at college. I no longer have the Recovery Disks, etc but I got WIN XP reinstalled and got all the drivrs I could from the Toshiba support site.
I cannot get the SD carder to be rcognized by the system at all. I finally got the SD Host controller "driver" installed (from http://aps2.toshiba-tro.de/bluetooth/?page=download)
but the SD Card reader does not show up on MY COMPUTER and when I install an older SD Card, the system does not see it. In Device Manager, it shows a PCI device that is yellowed out too.
Is there a specific SD Card driver I need or does anyone have any suggestions? I am at my wits end with this!

If you installed a retail version of Windows, the order of installing drivers and utilities matters.
Best to restore the hard disk from Toshiba recovery media.
Order Toshiba Recovery Media
Otherwise, use the attachment as a rough guide. Notice that the chipset software followed by the display driver are installed prior to other drivers and that the Common Modules is installed before other Toshiba utilities.
-Jerry
Attachments:
install.txt ‏5 KB

How do I use a bluetooth headset with garageband?

How do I use a bluetooth headset with garageband? I can't get it to work after many tries.

I can pair the headphones with the computer but the sound from GB is distorted and muffled. I can barely hear it. The set works with iTunes, but not with GarageBand.

How do i use my Platronix bluetooth with iPhone 4 to listen to music.

How do i use my Platronix bluetooth with iPhone4 to listen to music.
Its a mono bluetooth paired with the phone.
I dont want to buy a new stereo headset but can i use this same one.

One way is to sync the contacts from the old iPhone to iCloud. Then when you turn on the new phone and set it up for iCloud and turn on the Contacts in Settings >iCloud, they will come to the new phone. http://www.apple.com/icloud/setup/

How do I make Iphone proritise answering with bluetooth rather than ringing on phone?.

Previously, when I received a phone call in my car, the bluetooth radio would ring and then I would take the call by pushing button on steering wheel. Ever since installing latest IOS the bluetooth device connects but the phone just vibrates (doesn't even ring) The radio shuts off but the audio ring does not sound. Have to answer the phone manually. Defeats the purpose of having handsfree!! I note that when I phone voicemail while in car the screen shows options to use bluetooth, Iphone or speaker phone. When I am in the car I JUST want to use handsfree bluetooth (it is the LAW!!). Is this just a glitch in the new operating system update? and if so, when will it be repaired?

You can't. If iPhoto is open when you connect the phone then it will offer itself from importing.
Regards
TD

Continuity Bluetooth Calling & SMS on Macbook Pro (via iPhone 5) Not Working

Devices:
Macbook Pro Mid-2010 running OSX 10.10.2
Iphone 5 running iOS 8.1.3
*NOTE: I understand that due to the version of the Bluetooth protocol in my machine, not all continuity features are available (Handoff, Air Drop, MBP Instant Hotspot)
However SMS to IMessage and the ability to make and receive calls from my Mac should be OK according to Apple's system requirements one-sheeter:
System requirements for Continuity on iPhone, iPad, iPod touch, and Mac - Apple Support
================================================================================ =====================
Here's my problem.
I finally took the plunge last night and updated my iPhone 5 from 7.1 to 8.1.3 to access the iCloud Drive and additional continuity features integrated into Yosemite.
When I tried to pair my iPhone 5 with my MBP over Bluetooth, all seemed to go well for the first 5 seconds.
- Both devices were in discovery mode.
- Mac saw the phone and displayed a security code
- iPhone displayed the same security code and asked if I would like to pair with MBP
- Pairing took place. Each devices Bluetooth profile / device showed up in my MBP Bluetooth's Preferences and in my iPhone's Bluetooth.
- 5 seconds later, there's no connection between devices.
My iPhone displays:
"Connection Unsuccessful: Make sure [Macbook Pro] is turned on and in range." (The phone is 5 inches away)
Then sometimes I get this message:
"Connection Unsuccessful: [Macbook Pro] is not supported.
No rhyme or reason between the two either.
Here's the baffling part: When I activate my Phone's HotSpot function, the Bluetooth works and connects with my MBP allowing it to use my cell phone network's data for internet connectivity.
I don't understand what is going on or how to correct this? Can anyone succinctly explain how to correct this problems in layman terms?
If the devices can communicate long enough to exchange security codes and verify their identities, then use Hotspot, there is clearly a data exchange happening. Where is the break down taking place when it comes time to stay connected to so I can continue to use the limited continuity features.
I've seen this question posted before by people having problems with different model years of MBP including the most recents models, so I know it's not mutually exclusive to my model year, but cannot seem to find clarity on an answer.

Handoff Continuity Troubleshooting
iPhone, iPad, iPod touch, and Mac using Continuity - Connect

How Can I Use Bluetooth For Sharing With iPhones?

Hello, i have an iPod touch 3rd Gen. 32GB, And I'm Wondering How Could I Share Music or Photos With My Cousin's iPhone (Jailbroken iPhone), When I Turn The Bluetooth On, Nothing Shows Up On My iPod Or On Here iPhone,
So How Could I Share Things With Her I Have ''File Share'' And ''Bump'' Apps
So what should I Do???

You can't share music over air or by Bluetooth because of several reasons of which is understandable by apple. Apple doesn’t provide any way for you to copy files from your iPod back to your Mac/ between iPods or iPhones. While there are legitimate reasons for blocking bi-directional copying— which again the word music piracy comes to the mind
The only thing that I heard that you could share with iPhone to iPhone/ iPod touch is photos&contacts an app called "bump" and "Bluetooth photo share". With those applications you and your friend can share photos/phone contacts and other kind of files.
"Bump" application link below:
http://ax.itunes.apple.com/us/app/bump/id305479724?mt=8&partnerId=30&siteID=Tjuc Fgl1Woc
"Bluetooth photo share" application link below:
http://ax.itunes.apple.com/us/app/bluetooth-photo-share/id326109583?mt=8&partner Id=30&siteID=TjucFgl1Woc
Message was edited by: John-macOwner

How can I send stuff from one iPhone to another via Bluetooth?

How can I send stuff from one iPhone to another via Bluetooth?

There are some apps that will let you send photos from one iOS device to another over BT.

Is there a way to get a log of the bluetooth devices my iphone has been connected to? My Bluetooth car speaker phone was recently stolen from my car and appears to be on Craigslist.

Is there any way to get a log of the bluetooth devices my Iphone has been connected to? I recenly had my Bluetooth Jabra stolen from my car and now a simliar one is on Craigslist. I'd like to give my connection log to the police before I go and see if my Iphone recognizes the device in question. Any way to get any type of bluetooth device connection log out of my iphone?

Your contacts should still be on whatever program you sync your iphone to (i.e. Outlook, address book).
The iphone is not a stand alone device. It is designed to be synced with a computer. If you have not been syncing with a compatible program, then you are out of luck. Your contacts are not included in the back-up because it is meant to be synced with your computer.
"Although iTunes backs up most of your iPhone and iPod touch settings, downloaded applications, and other information (Contacts, calendars, notes, images in the Camera Roll), your audio, video, and photo content are not included in the backup."
http://support.apple.com/kb/HT1414

How do I Find/Set/Change a Bluetooth passkey on a T61 laptop with the Lenovo US/Eng Vista OS image?

I purchased a T61 two years ago. It came with the Lenovo Vista Ultimate OS, US/English. The T61 has Bluetooth, which I never used until now.
I try to pair a cell phone and a PDA (both Palm devices) with the T61, and the devices ask for the T61's Bluetooth Passkey. I don't know what the passkey value is, nor do I see anywhere to set, change or enter it.
This is how I know the the Bluetooth device driver is working on the T61: 1- The BT icon shows in the taskbar, the BT controt panels open, and even in Control Panel > Hardware and Sound > Bluetooth Devices, the phone name shows up. And strangely enough, at the bottom of the control panel, when the phone is listed (is discoverable), it shows "Paired: Yes", "Authenticated: No", attached image shows these values.
I'm stumped. Where do I lookup, set or change the T61's Bluetooth passkey?

Unfortunately that is not working. I've tried 0000, 000000, 00000000, 1234, and 123456 as the keys. No popups, no response whatsoever on the T61.
The devices seem to wait some timeout period and then a message "cannot connect to T61...". I don't have the exact message here in front of me, but can get it if need be.

Can I use a bluetooth headset as a microphone in iTunes?

Don't know if this is te right forum but its about iTunes!
I am very new to all this "wireless" tech being of the old school where everything had a wire attached but thanks to Alexander Traud I now have a phone, headset and two computers all conversing nicely wirelesly.
So, to the question. I am the aging DJ for our ex-pats club here in Spain and use my white iBook as an iTunes jukebox at home and as the player at the club for my 50's to 70's disco. Its great not having to throw around disks of vinyl anymore and a lot lighter and smaller to carry the record collection too! I was wondering if I could use the BT Motorola H500 headset instead of the wired microphone. I have tried but despite being able to play the iTunes output through the headset (not what I want to do) and the Sound preferences indicate that when I speak I am registering on the input bar I can't get my voice out the headphone output ie. where the main disco amplifier is plugged in.
Can I do this and if so how please. It seem a shame if you can't.
TIA
Mike

Hi Robert
Thanks for answering. I didn't know where to post other than the bluetooth forum which is relatively quiet and had no answers forthcoming.
Yes the voice isn't reaching the amp although it is registering on the input bar in the Sound System Prefs, just won't "play through" as it were. I can't see how it could be done I was just hoping someone might see something I am missing.
It seems a shame that you can't do it as iTunes on an old iBook makes a good juke box for DJ'ing and with everything becoming wireless these days it seems sensible that you could cut that one last wire.
Mike

Is there a stereo bluetooth headset that can pair with more than one device at a time?

Is there a stereo bluetooth headset that can pair, i.e. multipoint, with more than one device at a time?
Are the MacBook and iPhone 4 capable of multipoint bluetooth technoloagy?
The goal is for my wife to be able to watch her Korean TV soap operas on her MacBook and still receive a call on her iPhone 4 via a stereo bluetooth headset.
I was looking at the Motorola S10-HD but after further review saw that it only pairs with one device at a time.
Appreciate any and all input. My Googling has returned no results.
Rick

TeslasBB wrote:
pairing my BB8330 with my blue tooth earphone(TM:jawbone) and my microsoft sync thats in my car simultaneously? if i pair with the car, will i have to pair my jawbone all over again?
You can only pair one device at a time to your 8330, or any other phone for that matter. The "pairings" are saved to the phone, you can use one or the other and you won't have to pair it again. Once you turn your bluetooth device on and the phone is on, they will find each other again.
Hope this helps,
John
Stevie Ray! 1954-1990
** Don't forget to resolve your post with the accepted solution.

No bluetooth in my S100

Similar Messages

Maybe you are looking for