"No Cable Connected!" Error

"No Cable Connected!" message when trying to connect new Benq GL2750 LED to my new Mac Pro with Mini Display to HDMI adaptor. Anyone know how to solve the problem??

Mini DisplayPort cables are diabolical.
You must push them into the socket until essentially ALL ot the metal part disappears.

Similar Messages

Nokia E66 Cable Connection Error

Hi,
Am Using Nokia E66-1(08) ( RM-343) with the firmware version 410.21.010
I have a problem with connecting my mobile to PC via cable. The cable is working fine. ( I have checked it by connecting the other mobiles)
When I connect the cable, It asks me to select the options such as "Mass Storage", "PC-Suite" etc. But once I select "PC-suite" from the available options, mobile doesn't get connected to the PC. I cannot see the USB connection symbol in the right top side of my mobile.
Can anyone help me on this.
Should I go for repairing the connection port of my mobile?
OR It mite work with a firmware update\re-installation ?
But again, is the cable connection port of my mobile not working? But it detects that cable is connected, because when I connect the cable, it asks for the type of connection I want to make...
Plzzzz help me out.
Thanks,
Code3

I have same prblm with nk x3-02, can anyone help me out.

No error with VISA CONFIG SER. PORT when no cable connected

I'm using LV8.5 and VISA CONFIGURE SERIAL PORT.VI, with an error indicator connected, and I expect to see an error displayed when I have NO SERIAL CABLE connected to my pc. Shouldn't this condx generate an error? If not, what can I do to display an error when no cable is connected?

wb2nvy wrote:
I'm using LV8.5 and VISA CONFIGURE SERIAL PORT.VI, with an error indicator connected, and I expect to see an error displayed when I have NO SERIAL CABLE connected to my pc. Shouldn't this condx generate an error? If not, what can I do to display an error when no cable is connected?
Are you saying that you wan the configure serial port VI to throw an error if you don't have a cable connected to the serial port?
It can't. How would the serial port know whether a cable is connected or not? The VI configures the port which is the actual hardware implementation inside your PC. It doesn't know what is happening beyond then connector on your PC.
You do have some alternatives though. If the device you are going to communicate with puts any voltage on any of the hardware handshaking lines, you could check the status of the hardware handshaking lines and see if they are enabled or not. If they are not, you can throw your own error saying the cable or the device is not connected. Or if the device doesn't do that, you could make your own communication cable that does a loop back on the hardware handshaking lines. If the line is not enabled, then the cable must not be connected. Of course in that case it won't tell you whether the other end of the cable is connected to anything.

My iPhone 4s is stuck on a black screen that shows a USB cable connecting to iTunes. The phone will not turn on and the iTunes logo as I described only shows up when I plug the phone into the charger or my computer. I have tried the reset in restore mode

My iPhone 4s is stuck on a black screen that shows a USB cable connecting to iTunes. The phone will not turn on and the iTunes logo as I described only shows up when I plug the phone into the charger or my computer. I have tried the reset in restore mode as well as the DFU? mode and it still will not work. I have the latest version of iTunes on my Mac. My error code was 2002. I also tried it on my laptop (windows 8.1) and none of the above worked. My error code on my laptop was 02. The phone is through Verizon and it has absolutely no damage. It was working fine up until this and I have been trying to fix it for 2 days. Please help! I am unsure of what version the phone was currently running on before this because I have another iphone that's my primary phone and have not used this one in about a month. I do not believe it was updated to IOS 7.

Your iPhone is in recoverty mode at the moment so to possibly get it back up and running you would need to do a restore as you have been trying. Follow the steps in the article below for the specific error messages you have been receiving. If after following all steps the issue remains book an appointment at a local Apple Retail Store to have the iPhone evaluated.
Resolve specific iTunes update and restore errors

HP Officejet Pro 8600 Network connection error message in EWS

I just got an Officejet Pro 8600 Premium. The printer is connected to the network via a network cable. When navigating through the EWS, sometimes the message "Network connection error. Check network and try again." message is shown (the message could appear in various pages, such as Settings, Tools, etc.). Refreshing the page should get rid of the message.
At first, I suspected if it was a problem with the network. So I pinged the printer's ip address continuously. It did not miss a single beat. The printer prints and scans well via the network. So I think the error may be caused by something inside of the print, such as bug of EWS software, or internal error.
Anyone see the same message during the use? Any suggestion? Does it indicate there is hardware problem with the printer? Thanks.

HP Support has escalated the case. I referred this thread in the support request. Hopefully, they can have a look at the issue.
For me, the only setting does not stick is "Use the same time zone set on this computer" in Settings\Date & Time. I've created another ticket for this issue. 8500A has the same problem.
You can try to restart the EWS. Unplug the power cord while the printer is on. Then wait 15 sec and reconnect the power cord. Press the power button if the printer does not turn on by itself.
If you would like to reset to the printer and reconfigure from scratch, you can check here: http://h30434.www3.hp.com/t5/Printer-All-in-One-Install-Setup/How-to-reset-Officejet-Pro-8600-Plus-P...

HP Photosmart 6520 Server Connection Error: -1: Apps don't work and Scan to email doesn't work

My HP PhotoSmart 6520 has a persistent error to connect to the server and therefore Apps and Scan to email doesn't work.
I have manually set DNS to 8.8.8.8 / 8.8.4.4, I have installed latest driver on my Macbook pro, I have updated firmware, but still not working. Weird is also that in my ePrintCenter, the Apps I see there are not in line with thos visible on the printer.
Detail is that I have set up the printer on a Windows PC but recently changed to Mac.
Printing, scan to Computer all works fine.
Help! I have read a lot on forums but so far no solution for me!

Hi Jack6520,
Welcome to the HP Support Forums. I see that you are unable to connect to the apps and use the scan to email feature of your Photosmart 6520 printer due to a server connection error.
First off, thank you for the very detailed information, I really appreciate it.
To better assist you, would you please provide some additional information:
When you set the manual DNS servers, did you also set a manual IP address for the printer?
Have you changed routers or internet service providers recently? Have you updated the firmware on the router? If you have an ISP-provided router, do you know if they pushed out a firmware update?
Have you recently installed any new anti-virus/malware software? If so it may have blocked the ports the printer uses to communicate. I’ve included a post by VisionAiry titled “Check the Anti-Virus for Blocked Ports and Timed Scans”.
Do you have a guest network setup? Please Print a Network Configuration page. It will let you know how many networks the printer sees. A guest network will have the same name as your network with a tag about it being the guest network.
Previously did you customize the printer’s ePrint email address? I’m asking this because I might ask you to disable then enable the web services. If we have to take this step you will lose the customized ePrint email address without any ability to get it back.
What version of Mac OS X are you using? whatsmyos.com
Are there any cables other than the power cable connected to the printer?
Thank you.
Regards,
Happytohelp01
Please click on the Thumbs Up on the right to say “Thanks” for helping!
Please click “Accept as Solution ” on the post that solves your issue to help others find the solution.
I work on behalf of HP

Handle the Network Connection Error ...

The main purpose is to handle the Network Connection Error,
when there is a Network Connection Error or pc loss the
connection (remove the ETH cable),
and it work in IE but not with firefox.
When there isn't connection during play of sound1, Flash call
"sound1.onSoundComplete" that point to an other frame, where i load
an other es:Sound2.mp3, BUt there isn't connection and Flash call
"sound1.onLoad" with "success=false" and that's OK because i handle
the error for example retry to load every 10 Seconds.
With Firefox when it happens the player call load sound2.mp3
but there isn't connection and it can't find the file (OK) BUT is
NOT CALL the "sound2.onLoad" and STOPS it in this frame mute and
nothing more happens.
This is the sample Code:
//on frame (1)
sound1 = new Sound();
sound2 = new Sound();
//on frame (2)
sound1.onLoad = function(success) {
if (success) {
//on load OK...
trace("Sound1 loading ok...");
} else {
//on load FAIL...
trace("Sound1 error ...");
//call error function. (es: goto frame 1 and reload all.)
_root.sounderror();
sound1.loadSound("sound1.mp3", true);
sound1.setVolume(100);
sound1.onSoundComplete = function() {
//goto next frame and load the Second sound
gotoAndStop(3);
//on the Frame-3
//there is the same code but with sound2 and
"onSoundComplete" -> gotoAndStop(2); for a loop of the two
sounds.
Thanks in advance for HELP ME.
PLAEASE READ and Comment!!!
This is my work! Sorry for the Bad English.

Thanks for your support, i have modify like your suggest but
the problem continue.
I've notice that in local work very fine also with Firefox. i
try during play to remove in one shot all mp3 file, and it call the
error handler function correctly, But if i put it on the web, when
i unplug the eth cable, it stop after sound2 or 3.loadsond and
write me back it in a text box, stop! it NOT Call the onload
triger, and do not call the error function.
WHY ?!? in local work whit all browser, and on web only with
IE?
HELP ME PLEASE!
Post the new code:
//Frame#1
soundintro = new Sound();
sounda = new Sound();
soundb = new Sound();
soundintro.onLoad = function(success) {
if (success) {
//find soundi - wait for onsoundcomplete...
} else {
//Sound error
//Lunch error hander function.
_root.sounderror();
soundintro.onSoundComplete = function() {
debug1 = debug1+("Trace-> soundintro Complete
goto2..."+chr(13));
gotoAndStop(2);
d = new Date();
soundintro.loadSound("soundintro.mp3?r="+d.getTime(), true);
soundintro.setVolume(100);
stop;
//Frame#2
sound2.onLoad = function(success) {
if (success) {
//find sound2 - wait for onsoundcomplete...
} else {
//Sound error
//Lunch error hander function.
_root.sounderror();
sound2.onSoundComplete = function() {
debug1 = debug1+("Trace-> sound2 Complete
goto3..."+chr(13));
gotoAndStop(3);
d = new Date();
sounda.loadSound("sound2.mp3?r="+d.getTime(), true);
sounda.setVolume(100);
stop;
//Frame#3
sound3.onLoad = function(success) {
if (success) {
//find sound3 - wait for onsoundcomplete...
} else {
//Sound error
//Lunch error hander function.
_root.sounderror();
sound3.onSoundComplete = function() {
debug1 = debug1+("Trace-> sound3 Complete goto back
to2..."+chr(13));
//Back to 2 for loop
gotoAndStop(2);
d = new Date();
sound3.loadSound("sound3.mp3?r="+d.getTime(), true);
sound3.setVolume(100);
stop;

Cabled connection issue but wireless fine?

I wonder if there's a known issue and resolution to an issue I'm having with a client computer? The PC has been on a cable connection to the Hub v3 for around one year without any issues but it's suddenly blocking the PC via cable to the router. I've tried resetting the hub and also received a new one in the post which also did the same. I did have an issue with "netware" on the PC and other connections in there so for surety I've re-installed Windows XP on the PC and it works fine on my own LAN via cable ruling out the suspected failing LAN card. It also has Kaspersky Internet security 2012 on and nothing else. A clean registry
I haven't re-installed the BT software as I know it's not needed and for me either the hub has blocked the PC's LAN card mac address somehow or is failing? The only thing I haven't tried is the new hub with the new XP installation which I'll do tomorrow when I return the PC.
I can install a wireless adaptor and it'll work fine as does another PC on the LAN so DHCP is working in the router, just not for cables lol
Any ideas as to how I resolve this are welcome?
TIA
Andy

Thanks for moving and replying Molly I appreciate the time it takes as a forum owner/admin and can see the volume of posts you reply too so barely get time to read them but I'm a professional computer technician and never use (buggy) ISP given CD's for just that reason but if you'd fully read my post you'd have seen that I did say I hadn't installed the software. I've also got lot's of coasters though
The LAN card is an intel pro 10/100 about 6-7 years old (xp media centre) and has always worked like I said then suddenly it has an issue but only with the HH3? My LAN is on VM 100mb (naturally ) and the PC works great here so it has to be a clash between the LAN card and the HH3?
I updated the Sony Viao VGC -RC204 drivers (intel) and picked up on a security issue where the drivers are vulnerable to hacks but installing the driver did nothing to improve it. I haven't even run TCP optimizer in case I corrupt my clean registry & LAN drivers so I know the PC is clean & cannot be blamed for the problem.
I installed an ethernet to USB adapter to try & it worked straight away so that led me to believe the LAN card was failing but using it on my LAN it's fine! Maybe the HH3 has had a f/w update that knocks the intel drivers off or blocks them in the f/wall?
If I put the new HH3 in it should be fine & connect straight away yes? The server login details are preset in the HH3 then it's posted out? Or do I need to login & put them in manually as the new HH3 gives the same error, lol
I could use the ethernet to usb adaptor or w/l adaptor OR even try a new PCI LAN card in to see if it works but I'd rather get to the bottom of the problem as I don't like to be beaten
Anyone else seen this issue or can link to it ?
NOTE: My topic was moved to "the lounge" but on the forum index page there's no description of the forum category which is how I missed it so maybe an admin could put a decsription in there for us? and save a lot of post moves maybe

"printer not connected" error over a wifi network

I have a HP CP2025N laser printer that has been happily working on my Apple network. Now all of a sudden I keep getting a "printer not connected" error.
I reset the network to no avail.
I am running Lion, the printer is connected via an ethernet cable on a Apple Express routter that extends an apple extreme. Again this configuration has been running for two years now.
Any help would be appreciated.

If the printer works with AirPrint, you don't need the EPSON software and you should remove it. Then see below:
OS X Yosemite: Reset the printing system

Why does my phone keep popping up messages "This cable or accessory is not certified and may not work reliably with this iphone" when there is no cable connected?

Why does my phone keep popping up messages "This cable or accessory is not certified and may not work reliably with this iphone" when there is no cable connected? This has been happening since IOS7 was installed and has become worse with 7.1. I have reset the phone several times with no change.The phone charges properly & I have never used anything but an Apple Lightning cable.

I already cleaned the port with compressed air before submitting the problem. I since cleaned it with a toothpick and dug out some more lint. this seems to have just about fixed the problem since I have only had the error pop up 3 times since then and i was getting the error constantly before.

X2-01. There has been a connectivity error...

Just bought a Nokia X2-01 and I downloaded some games that require network access (to download sponsored content!). Since I don't have a data plan, I was wondering if I can connect to the internet through a USB cable connected to my computer. I have installed the Nokia Suite on my PC but could only figure out how to connect to the internet through my cell phone, not the other way around.
The error message that I receive is: "There has been a connectivity error and the application will exit now. Please check the connectivity settings and try again."
Solved!
Go to Solution.

Hi Fyan,
Welcome to the Nokia forum.
Like you've already found out yourself, you can use your phone's data plan to connect your laptop or PC to the interne. Connecting your phone to your PC's connection is indeed not possible.
Most devices have WLAN which enables you to connect your phone to the same network your PC is connected to, but as the X2-03 does not have a WLAN function, the only way to download apps will be through 3G.
If you don't want to get a data plan you can always buy a Pay-as-you-go SIM card with data credit and use this SIM card to download apps onto the device. It's a little bit of a hassle, but at least it'll enable you to download apps without receiving a high phone bill at the end of the month.
Hope this helps, let me know how you get on.
Iris9290
If my post has helped you in any way, please accept it as a solution or click on the white star, so that other users will be able to benefit from it too.

Time capsule connecting error

I'm having trouble connecting a new time capsule, I get "an unexpected error occurred.Try again" I'm trying to connect wirelessly, and have reset the capsule.

I'm just trying to use the time capsule for time machine backups, and keep my existing router for the internet access. It's a new time capsule and I'm trying to set it up for the first time, but when I try to use the airport utility, it gives me the error message, and won't let me get to the setup menu.
You do understand that the Time Capsule must connect to your existing router using a permanent, wired Ethernet cable connection, correct? This requirement is pictured in the Setup Guide that came with the Time Capsule.
The Ethernet cable must connect from a LAN <--> port on the existing router to the WAN "O" port on the Time Capsule. The Time Capsule can be located anywhere that an Ethernet cable will reach up to 330 feet or about 100 meters.
If you need help with the setup, we need to know what operating system is installed on the MacBook that you will use to setup the Time Capsule. It should be at least Lion (10.7.5) or higher, like Mountain Lion (10.8.x) or Mavericks (10.9.x).
If you are not sure about this, click the Apple icon in the upper left corner of the screen, then click About This Mac and post back with the OS X version number that you see there.

Connection error on wrt54g

i have a 2wire modem and have dsl internet. when i'm installing the program and it's checking for internet connection it tells me that i have a connection error and tells me to turn off my modem and turn it on again and it still doesn't work. I connected my modem cable to the wrt54g in the 1st opening and the blue cable that comes with the wrt54g on the "internet" opening and the other end to the harddrive and while it's set up like that i noticed that when i open internet a page opens saying that i have no internet. i need help, thanks

To set up the router, first you use an ethernet cable to connect your computer to one of the numbered ports on the WRT54G. Do not connect the modem yet. Then use the setup disk that came with the router. Put the setup disk in the computer's CD drive. Follow the instructions on the setup disk. The setup disk will tell you when to connect your modem to the Internet port on the WRT54G.
Message Edited by toomanydonuts on 06-19-200711:43 PM

WICD crashes entire system if no eth0 cable connected

If I boot without the network cable connected, system freezes few seconds after wicd deamon starts.
If I disconnect the cable (even while being connected to a wifi) when system is running, it freezes after few seconds.
There is no errors in wicd or kernel logs.
I tried reinstalling wicd, but it did not help. This is a fresh Arch 64 installation.
Last edited by Lockheed (2012-07-19 08:42:22)

You can safely blacklist atl1c and modprobe it when you need it. That way udev does not automatically load it but you can still manually load it. Blacklist does not provend manually loading modules.
I have the same problem with the proprietary broadcom-wl driver. When udev tries to autload wl, the incompatile brcmsmac driver is also loaded resulting in a kernel panic.

Net connection trouble: "No Ethernet cable connected or the device is not responding"

Hello
I have been plagued by a dropping Net connection for a couple of months, and as it has been getting worse lately I have tried to sort out the problem.
I have simplyfied my connection between the computers and the VSDL fiber modem by bypassing my AirPort Express and Ethernet hub and connecting the three computers directly to the built in ports on the modem.
Since I did that a new error message has started appearing on my Mac Mini, saying that I have no Ethernet cable connected to the modem, or the device is not responding. At the moment I have two of the machines connected, and the Mac Book Air seems to work without problems. There are lights on the Ethernet ports on the modem, and they are lighting up for the iBook even when the Mac Mini connection drops. When the Mac Mini connection drops the lights go off on its Ethernet port on the modem.
This seems to point to some sort of trouble with the Mac Mini. Is there a way to monitor what's going on? Can I use Terminal, for instace? It can't be the settings, and it cant' be the cable, so it must be related to the hardware I suppose. I am using DHCP to connect to the modem.
The connection drops arbitrarily, sometimes for long periods of time, and then comes back up again by itself.
Any ideas for trouble shooting etc?
Best
Hans Karlsson

BDAqua
Thanks again. Unfortunately, the problems are back again. Had a stable connection and connected the AirPort again. Everything was working fine. Then all of a sudden the connection dropped again today.h
Connected a LAN cable directly to my MacBook Air and got the connection to work immediately.
Took that cable and connected to my MacMini, again, connection came back immediately.
The AirPort (in Brigde Mode) is also connected, but gives me a blinking orange light, and the same "no cable or (modem) is not responding" message again.
I guess this must rule out hardware problems in the computers.
Ligth for the LAN cable port on the modem connected to AirPort is dead. Moved the cable to another port, light still dead.
Shut down AirPort Express, still same orange blinking light when I switched it on.
I now suspect there is something going on with the AirPort Express. Just bought it, and I had the same problem with it's predecessor, but...
Is there any way to trouble shoot the AirPort Express?
I can connect to it Wirelessly, But AirPort Utility says it has been removed from the Network. In the Network Preferences it says it has a self-assigned IP. For Network Settings I get green lights for everything except Network Settings, which gives me a yellow light. It also says the Internet connetcion is working correctly.
Indeed, when I made the direct Ethernet connection inactive I still get a working connection over WiFi, in spite of the blinking orange light on the AirPort and a yellow light for Network settings in Prefereces....
In the console things look normal:
8/7/12 10:04:27.269 PM Apple80211 framework[231]:
com.apple.message.domain: com.apple.wifi.timeout.scan
com.apple.message.signature: Success
com.apple.message.result: pass
com.apple.message.value: 3149.000000
com.apple.message.summarize: YES
Still confused

"No Cable Connected!" Error

Similar Messages

Maybe you are looking for