No Canon Pixma MG8120 printer found

I am unable to print a Pages document from the iPad2. I have a newly-installed Airport Extreme with its USB connected to a Canon Pixma MG8120 printer. When attempting to print a Pages document from the iPad2, under Printer Options, I must select printer. The response to my attempt to select is "No Printers Found." This is odd since "Share this printer on the network" is checked in Print & Fax in System Preferences. What step or steps am I missing? Thanks for your help.

That printer is not supported by AirPrint. Only a few HP printers currently support AirPrint. You'll have to use an app in order to print from the iPad. Printopia, Print n Share, and PrintCentral are the apps most people use. Of course, Canon may also have an app, so you should check this too in the app store.

Similar Messages

HT2250 I have an Apple network utility that with the previous printer (Canon PIXMA iP 5000) found the printer on the Network for use on a wi fi system but a newish printer (Canon MG6150) does not show up as Bonjour. Is that correct?

I have an Apple network utility that with the previous printer (Canon PIXMA iP 5000) found the printer on the Network for use on a wi fi system but a newish printer (Canon MG6150) does not show up as Bonjour. Is that correct?
paul.kelly

Hi Steve,
No expert, but since nobody else has piped in...
Did you setup the DNS Server IP?

Installed a wireless canon Pixma MX432 printer back in November for use with my Mac Book Air. All was working normally until this past week when I began getting a message, "printer not connected." What is going on? Netgear Wireless N Router seems to be ok

My new canon Pixma MX432 printer is not printing. It was printing fine until about ten days ago. I use a Netgear Wireless N router, which is also new. What do I need to do. I get a message when trying to print that says "printer not connected." In addition, my old Gateway laptop will still print fine apparently because it has a cable connection to the printer. Puzzled!

Have you tried rebooting the router? I would unplug it, wait a few seconds, then plug it back in. Be sure you know the password etc. if that doesn't work, try unplugging and rebooting the printer. Good luck!

I am attempting to connect my Canon Pixma MG5220 printer/copier/scanner to my MacBook Pro OS 10.6.8. After loading software from Canon and attempting to print, I get the following message: NT_STATUS_ACCESS_DENIED. What can I do to fix this?

I just purchased and installed a Canon Pixma MG5220 printer/copier/scanner to my PC desktop with Windows XP. It works fine. It has been successfully installed on my network and I am able to use it with my laptop running VISTA. However, I am trying to connect it to my MacBook Pro OS 10.6.8 and I am not having much luck. I can see it as one of the printer choices when attempting to print; however, I get the following message:
NT_STATUS_ACCESS_DENIED
I have been searching for answers, but nothing seems to work yet. Does anyone have any suggestions?
Thanks.

Let me understand:
- you have purchased named canon, which is conencted to your PC running windows xp
- downloaded driver for win xp, and canon works fine
- canon is connected to that PC via USB
- that Canon is also activated as network printer, by allowing print sharing in windows; how did you set that option?
- now, you are in Mac OS x 10.6.8, downloaded Canon driver for Mac OS X, installed it, detected printer on the network, printer was installed; was it detected as attached to that PC running win XP? or not?
or you set canon by being connected to your mac directly via USB?
Now, there are some questions you should answer as some details are missing, and your initial text is not clear. Can you print if Canon is connected directly to your mac? did you try that? if not, do it before answering.

I have a problem with color prints from photoshop elements 12. The pictures are too light and with strange colors. I have a Canon pixma mg615I0 printer and use mac os X yosemite. The pictures are taken with a coanon eos 550d in the color space sRGB. I hav

Hi
I have a problem with color prints from photoshop elements 12. The pictures are too light and with strange colors. I have a Canon pixma mg615I0 printer and use mac os X yosemite. The pictures are taken with a coanon eos 550d in the color space sRGB. I have followed adobes recommendations and have tried both letting the printer respektive photoshop manage the colors. But nothing works. I see that there are different opinions about which is best to do so I tried both. I have the latest printer driver installed. Can anyone help me with this?

Do the following:
Print a test page from the printer. Perhaps the print head needs cleaning via its maintenance facility.
Let the printer manage colors, not PSE
Calibrate the monitor

How do I set high resolution on my Canon Pixma 600 printer?

How do I set high resolution on my Canon Pixma 600 printer? Also the copies from my computer look ok, but when I copy them from the printer, I can hardly read the print. Any help out there? Thanks , Martha

Hello mlshouse1758.
Additional troubleshooting will have to be done to narrow down the cause of your copy issue. Please contact our support group using the "Contact Us" link below for additional assistance.
This didn't answer your question or issue? Find more help at Contact Us.
Did this answer your question? Please click the Accept as Solution button so that others may find the answer as well.

Best Storage Practice for Canon PIXMA MG5420 Printer?

Hello,
My Canon PIXMA MG5420 Printer will be inactive for several weeks. What is the recommended best practice for preventing the ink cartridges and printhead from drying out and clogging due to inactivity?
Thanks,
Bill

Hello BSquared18,
The printer can be stored with the ink tanks and print head installed, make sure the printer is powered off properly so that the print head is capped. If you have print quality issue once the printer is out of storage, follow the steps listed HERE to perform a print head cleaning.
Did this answer your question? Please click the Accept as Solution button so that others may find the answer as well.

I have a PIXMA MG8120 Printer with the error message 6A81.

I have a PIXMA MG8120 Printer with the error message 6A81. I have turned off the power many times as well as unplugging the power source for a full day. There are no obstructions. What do you suggest?

For general advice see Troubleshooting issues with iTunes for Windows updates.
The steps in the second box are a guide to removing everything related to iTunes and then rebuilding it which is often a good starting point unless the symptoms indicate a more specific approach. Review the other boxes and the list of support documents further down page in case one of them applies.
Your library should be unaffected by these steps but there is backup and recovery advice elsewhere in the user tip.
The section Install missing components has advice on breaking down the iTunes installer into the individual .msi files which might prove useful if AAS won't install normally.
tt2

How can I get iMac to recognize Canon Pixma mp990 printer wirelessly?

Although my Canon Pixma MP990 printer/scanner shows I've properly set it up for wifi, and the blue wifi light illuminates on the printer, my iMac now refuses to recognize that my printer is connected. Imac now shows the printer as offline. When the printer was set up for corded/wired connection, the Imac worked fine with it. How can I get iMac to recognize the wireless printer setup? Thanks!

Hi ..
Click here > Canon U.S.A. : Support & Drivers : PIXMA MP990
Then click Wireless Help
Make sure the printer is recognized in System Preferences > Print & Scan > Print
If not, download and install the drivers designated for the mp990 model.
In the System Preferences > Print & Scan > Print window, click + (plus) to add the printer.

Upgrade to Yosemite 10.10.1 caused my Canon Pixma ip8500 printer to stop working. Canon no longer supporting this printer. Any solutions?

Upgrade to Yosemite 10.10.1 caused my Canon Pixma ip8500 printer to stop working. Canon no longer supporting this printer. Any solutions?

Hi
try this
resolve my printer problem.
with Yosemite, Apple have upgraded CUPS to 2.0, and CUPS work different. So you need to change one think in configuration.
open terminal, and write the following commands:
sudo sh -c 'echo "Sandboxing Relaxed" >> /etc/cups/cups-files.conf'
you asked for the password for superuser
sudo launchctl stop org.cups.cupsd
after this check in print queue if the printer is ready and not in pause mode.
The printer now should work, if the printer only print in B&W you need to change the configuration in CUPS web interface.
try http://localhost:631/ ; if you receive a error telling the web interface is disabled, type in terminal services the following
cupsctl WebInterface=yes
after this try again http://localhost:631/
after this choose in the web page "Adding Printers and Classes", bellow the CUPS for Administrators title.
in the new page, choose manage printers; after this choose your printer.
in the page of printer choose from the second combobox the option "set default options";
in the option page, change the color mode from monochrome to color, and save hitting the button "set default option", you be asked for a user and password with admin privileges.
After this your print is ok.

Canon pixus / canon pixma ip100 printer

hi
I'm trying to get a Canon Pixma iP100 printer connected by usb working with my arch linux.
cups 2.0.1-1
linux 3.18.4-1
for this I created and installed the following packages from the AUR repo
cnijfilter-common
cnijfilter-ip100
and installed the printer over the cups web interface.
the printer is detected as usb://Canon/ip100%20series?serial=123456 as soon as I connect it by usb.
when I first tried to print a test page, there was an error about the missing file /usr/lib/cups/filter/pstocanonij so I copied it from the pkg folder to this location.
when I now try to print the test page, the status is changing to "Sending data to printer" and the print job disappears after a short time. But the printer isn't doing a thing.
I also tried to print over the console
lp -d Canon_iP100_series -oraw out.txt
but the only thing that happens is that the printer's status led is blinking once.
I was also able to grab the data (pdf) which is sent by cups to the printer: https://filepaste.puzzle.ch/downloads/3 … d00047-001
thanks for any help
Last edited by psunix (2015-01-29 15:41:43)

now I installed the printer with the gutenprint driver, but no change so far.
gutenprint v5.2.10
Last edited by psunix (2015-02-02 15:06:09)

Why won't Canon Pixma MG5350 print in black and white?

Why won't Canon Pixma MG5350 print in black and white?

Why won't Canon Pixma MG5350 print in black and white?

Can't add Canon Pixma MX310 printer with OS X 10.10.2 Yosemite

I just got a new laptop that is running OS X Yosemite. I have my Canon Pixma MX310 printer plugged in via USB but I can't add it. When I go to the Add screen in preferences, in the default window, Canon MX310 series comes up. When I select it, I have to "Choose a Driver" in order for the add button to not be greyed out. Auto select is greyed out so I can only choose Select software which doesn't have anything for Canon or Other which is to select a downloaded driver. Problem is, when I go to the Canon website to download the driver it says "There is no driver for the OS Version you selected. The driver may be included in your OS or you may not need a driver." Any ideas?

There is no driver for the OS Version you selected. The driver may be included in your OS or you may not need a driver." Any ideas?
http://support.apple.com/kb/HT3669 Printer and scanner software available for download
http://support.apple.com/kb/PH18614 OS X Yosemite: Reset the printing system
What to do when you can't print
None of the above works, contact Canon Support.

Help getting Canon PIXMA MG2520 Printer to Print Wirelessly

I just got my Canon PIXMA MG2520 printer set up. Everything worked perfectly. I downloaded the drive and plugged it in and it worked. However, I cannot get it to print wirelessly. With my last printer there was a simple step to get the printer to do this. Something I checked or unchecked, but I can't remember what that was. Can someone help please? Thanks.

Do you have your printer setup in its setup panel to connect to your WiFi network?
When you say you plugged it in and it worked, are you saying you used a USB cable to try it?
If the printer is setup to connect to your WiFi network, you may only need to power off your router, wait a few seconds and power it back on for your printer to be seen on the network.

I have a Canon Pixma i4700 printer and since buying my iMac I'm finding it difficult to print photographs without a severe warm (red) tone.

I have a Canon Pixma i4700 printer and since buying my iMac I'm finding it difficult to print photographs without a severe warm (red) tone.
What am I doing wrong?

I can't give you detailed instructions, but there should be a way to print a built-in test page. If the color is off on that, the printer has an internal problem such as a clogged head.

No Canon Pixma MG8120 printer found

Similar Messages

Maybe you are looking for