No connection after starting or restarting the system

Hi,
I have a problem.
There is no internet connection after start or restart.
Until last week there had been no problems. There was an automatic connection with my SPEEDTOUCH9FF4D8.
But suddenly it does not connect automaticly. I can select SPEEDTOUCH manualy and than it works...
Thank you for your answers.
Mac Book   Mac OS X (10.4.10)  

Hi im slightly confused by your post whether its the computer not connecting to the network automatically or whether there is no internet connection to the router at all but heres a few things to try anyway!
First of all, if the internet goes down and restarting the router doesn't solve, then unplug your cable modem for at least 5 mins, the cable modem needs to forget the MAC address of the previously plugged in device. Then start it up and when the ready lights are on the router (or about a minute after starting the router) then plug in the router and the connection should work!
Secondly, if your computer doesn't automatically connect to the network anymore (presumably your on mac osx) then go to System Preferences / Network then select configure AirPort. Make sure 'By Default, join' is Automatic, then go to options at the bottom and select 'Automatically Join and Open Network'
Hope this helps!

Similar Messages

  • Hi, I just bought a new Macbook Pro 15" with SSD 256 Gb and its almost a brand new a while ago i was trying to connect to my home wireless network it said that your airport is not configured then I restarted the system but it didn't restart it shows the "

    Hi,
    I just bought a new Macbook Pro 15" with SSD 256 Gb and its almost a brand-new (the 4th time to use the device) a while ago i was trying to connect to my home wireless network it said that the connection is timed out so i clicked the airport sign on the top it said that your airport is not configured then I restarted the system but it didn't restarted it showed the grey screen with the apple logo and the spinning wheel for more than 10min so I tried the force shutdown by pressing the power button till it switched off I waited for 5min then pressed the power button to start or boot the system and again the grey screen with the apple logo and the spinning wheel, I waited for more than 20min nothing changed, any solution please?
    Your help is really appreciated"

    Thanks a lot i followed the instructions for safe mode (i found out that i was pressing the C button after restarting) i did whats written there but the repair couldn't be performed so in addition i needed to re-formate the HD so i erased the volume and then repaired the disk--> quite disk utilities --> start the installation from the installation DVD.
    Thanks really appreciating your help

  • After downloading mountain lion the internet does not start automatically after start or restart but if I use diagnostics it starts is there a simpler solution

    After downloading mountain lion the internet does not start automatically after start or restart but if I use diagnostics it starts is there a simpler solution?

    Extensions can sometimes be the cause of problems. If the problem does not occur in Safe Mode, then you can disable your extensions one-by-one until you find out which one is causing the problem. See [[Troubleshooting extensions and themes]]

  • Losing systemprofile after restarting the system

    Hi,
    I've been dying to know what's this is, and i don't really get it : 
    It happened 2 weeks ago, i "stopped" windows, and when i went to the office, the desktop vanished, no apps showing in the apps screen (don't know what it's called). And i got a message something like : "C:\windows\system32\config\systemprofile\desktop
    is no available", but i found a fix, copying all the data from "c:\users" into that folder.
    Why it's in two locations, users and in windows profiles ? why i lose the data when i copy the folders again and restart the system ? 
    I ask for an explanation and the fix to the issue, if someone knows the origin please tell me.
    System : 
    - Windows 8.1 single language x64 (updated from windows 8 single language
    - Sony vaio SVF15218SFW
    - 4Gb of ram
    - Intel i5-3337U
    Thanks in advance.

    How did you stop windows?
    Is your profile setup by a company GPO to log in with a assigned domain/company user name and you want your own personal user?
    This works for 8 as well, if you tried this method and your computer is a company with GPO"S set, you will need the system admin login to set the GPO not to Clear the user profile upon logout.
    Stop = Shut down (sorry, french pc)
    No i don't use a GPO, or a company policy, it's my own pc, I use my email to login, not a local account, Besides I get an error when i reboot : "service Service is not accessible..." something like this, i couldn't read the whole thing and it disappeared
    a little while after showing, didn't have time to write or screen capture, but as you said it could be a problem with the policy to delete the profile if the pc is restarted. But it appears that even if i create a new local user, and copy all the data from
    the old account "c:\users\user" into the the new "c:\users\new_user", i don't think it'll resolve the problem, because it reads the profile from config folder in system32. 
    When i try to open Group Policy Editor,
    with GPEDIT.MSC
    i get the error that it doesn't exist as a command.
    If i'm the only pc user, then i'm the admin, how can i access that "GPO not to Clear the user profile upon logout".
    Thanks for your answers

  • Hi, I got a big problem. I restored my mac and after I erased everything and started to restall the system, it showed I need to give the apple ID that was purchased the lion. The problem is that I lost my CD, and I don't have an ID with lion purchased

    Hi, I got a big problem. I restored my macbook pro and after I erased everything and started to restall the system, it showed I need to give the apple ID that was purchased the lion. The problem is that I lost my installing CD, and I don't have an ID with lion purchased, so what should I do? Do you sell the system software?

    This is a user forum; we're not  Apple. 
    Please contact the Apple Support folks directly for issues related to hardware and software purchases.
    The particular model of MacBook Pro is a key detail here, as the Mac model will determine the oldest version it can boot, as well as whether it'll boot more current software.
    AFAIK there is and was no Lion installer DVD available.  It was a download.  AFAIK, the last DVDs commonly available were for Snow Leopard 10.6.  Snow Leopard DVDs are still available in the Apple online store in various countries, if your MacBook Pro is old enough to be able to boot that version.
    If your MacBook Pro purchase with Lion wasn't registered with Apple, then you'll have to discuss this directly with the Apple Support folks, or repurchase Lion from the Mac App Store (which will usually involve a call to Apple for a redemption code as it's old software), or you'll "purchase" (it's free) Mavericks OS X 10.9 and wipe and install that assuming your MacBook Pro supports Mavericks.  If you didn't purchase the MacBook Pro from Apple (and it was shipped with an older release), then you'll end up acquiring a redemption code from Apple for Lion, or installing Mavericks.
    For completeness and given you're probably already aware of this, the usual approach for restoration with recent OS X versions is via the recovery boot (more details).  If the disk is wiped and you can't get Lion, then you'll probably end up reinstalling with Target Disk Mode using another Mac with a compatible FireWire or Thunderbolt port and a cable.  Or visit the local Apple Store.
    sputniki: Once OS X 10.7 or 10.9 has been reinstalled, yes, getting Time Machine configured and going is undoubtedly on the agenda.  But had there been a viable backup here, I expect jianghua would have used it.

  • How do I use the commands to start and restart the jmqbroker normally?

    How do I use the commands to start and restart the jmqbroker normally?
    Because I have tried to use "jmqcmd shutdown bkr" and then tried to type
    "jmqbroker" to start up. My screen hangs up and seems that the process
    hangs up. The message is
    [28/Jun/2002:18:29:07 GMT+08:00] [B1060]: Loading persistent data...
    [28/Jun/2002:18:29:08 GMT+08:00] [B1039]: Broker "jmqbroker" ready.
    The prompt is hanged until I press CTRL-C.
    Then I got the following message:
    [28/Jun/2002:18:32:07 GMT+08:00] [B1047]: Shutting down broker...
    [28/Jun/2002:18:32:07 GMT+08:00] [B1077]: Broadcast good-bye to all
    connections ....
    [28/Jun/2002:18:32:07 GMT+08:00] [B1078] Flushing good-bye messages
    [28/Jun/2002:18:32:07 GMT+08:00] [B1056] Cleaning up persistent
    store...
    [28/Jun/2002:18:32:07 GMT+08:00] proceessing 0 messages and cleaning
    up 0 files...
    [28/Jun/2002:18:32:07 GMT+08:00] [B1063] Done
    [28/Jun/2002:18:32:07 GMT+08:00] [B1048]: Shutdown of broker complete.
    Then, I use jmqadmin to invoke the console, I can start the broker
    again, it gives me
    Error encountered while connecting to the broker: "MyBroker":
    Broker Host: 'localhost'
    Primary Port: '7676'
    [C4003]: Error occurred on connection creation, - caught
    javax.jms.JMSException
    Please verify that there is a broker running on the specified host and
    port.
    I used ps -def | grep jmq there is no process anymore.
    Is it a bug? Would somebody have any idea on what went wrong?

    'jmqbroker' is the command to start a broker.
    When you type 'jmqbroker' in a command window,
    unless you put it in the background, the shell
    prompt won't return until the broker is shutdown.
    So when you see 'Broker "jmqbroker" ready.', it tells
    you that the broker is running and is ready.
    When you CTRL-C the process, it has the same effect
    as using jmqcmd to shutdown the broker. And so after that,
    there's no jmq processes running since you have just
    shutdown the broker.
    Remember that the jmqcmd/jmqadmin 'restart' command is to
    restart an already running broker. jmcmd/jmqadmin does
    not support starting a new broker instance.
    If you are using csh, end the jmqcmd command with an ampersand ("&")
    to have the broker running in the background. An alternative is to
    stop the process with Ctrl-Z then input the command "bg" to have that
    process resumed in the background.
    The problem with not being able to start a broker using the
    administration console is a documented limitation of the product that
    Yvonne also mentioned. Check the Administrator's Guide for that.

  • X121e bios loop : "configuration changed - restart the system"

    After changing some settings in BIOS i got stuck in a reboot - loop.
    * Cannot access the BIOS any more - pressing F1 changes the message to "Entering BIOS Setup Utility" followed by the message "configuration changed - restart the system"
    * F12 changes the message to "Preparing Boot Device List" followed by  "configuration changed - restart the system" and the system reboots again.
    * Tried to remove the battery, pressing the power button for 10-15 sec. and reboot with AC Adapter connected
    * Tried to remove the battery and unplug the bios battery for 3 days the reset the bios - doesn't work
    * Tried to boot via USB (BIOS update, FreeDOS with BIOS update, Ubuntu-Live-USB) - nothing worked .. didn't change the boot-order - i always prefer USB boot
    * Removing hard-disk produces the message "no operating system found"
    Are there any tricks for resetting the BIOS to defaults, flashing BIOS without booting from USB?
    see
    * http://forums.lenovo.com/t5/ThinkPad-Edge-S-series/E-325-bios-settings-changed-keeps-rebooting/td-p/...
    * http://forums.lenovo.com/t5/X-Serie-ThinkPad-Notebooks-inkl/x121e-Configuration-changed-Restart-Syst...
    - there are several people with this issue ...

    In service center they said that motherboard is glitchy and needs replacement.
    So it was a hardware fault.

  • Ive tried loading this new software, and step 1 and 2 were successful, but after trying to restart the loading grey screen wont stop loading?

    ive tried loading this new software, and step 1 and 2 were successful, but after trying to restart the loading grey screen wont stop loading?

    I had a similar problem, does the phone show anything on the screen, for example "update failed, connect to computer" if it does, try opening "Sony PC Companion 2.1" click start on "support zone" then click "phone/ tablet software update" a message will pop up, press repair my phone / tablet, select your phone in the list, then follow what it says, try doing this even if the phone shows nothing, you will lose everything, all data will be gone if you follow my steps

  • [TP x120e] Continuous "Configuration changed - Restart the system." error

    I played with my bios (disabled/enabled mic, webcam, LAN and so), but after exiting the bios, Thinkpad x120e  reboots continuously with the error message "Configuration changed - Restart the system.". I was not able to boot from any USB/HDD and also I can not enter to the BIOS. Hard bios reset won't help. Any ideas?
    Thanks!

    Hello,
    Have you tried unplugging all power, including the internal CMOS/RTC backup battery, from the ThinkPad X120e, leading the unit alone for a few minutes to let any capacitors holding a residual electic charge drain, holding down the power button for 30 seconds to complete the operation, then plugging in the AC charger without either of the batteries installed, then holding down the F1 key while pressing the power button to see if that gets you into the BIOS settings?
    Regards,
    Aryeh Goretsky
    I am a volunteer and neither a Lenovo nor a Microsoft employee. • Dexter is a good dog • Dexter je dobrý pes
    S230u (3347-4HU) • X220 (4286-CTO) • W510 (4318-CTO) • W530 (2441-4R3) • X100e (3508-CTO) • X120e (0596-CTO) • T61p (6459-CTO) • T43p (2678-H7U) • T42 (2378-R4U) • T23 (2648-LU7)
      Deutsche Community   Comunidad en Español Русскоязычное Сообщество

  • I'm operating CS5 on iMac 10.10.2..Q.  The last two or three times I have tried to use "Merge to HDR Pro" it will not complete the task and closes down.  How do I fix it...I have restarted the system but no help...RDGS, Mike Frey

    I 'm operating CS5 on iMac 10.10.2.....Q.the last two or three times I have tried to use "Merge to HDR Pro" the aplication quits with no image...I have restarted the system which does not solve the problem. 

    Details about your setup, please.
    BOILERPLATE TEXT:
    Note that this is boilerplate text.
    If you give complete and detailed information about your setup and the issue at hand,
    such as your platform (Mac or Win),
    exact versions of your OS, of Photoshop (not just "CS6", but something like CS6v.13.0.6) and of Bridge,
    your settings in Photoshop > Preference > Performance
    the type of file you were working on,
    machine specs, such as total installed RAM, scratch file HDs, total available HD space, video card specs, including total VRAM installed,
    what troubleshooting steps you have taken so far,
    what error message(s) you receive,
    if having issues opening raw files also the exact camera make and model that generated them,
    if you're having printing issues, indicate the exact make and model of your printer, paper size, image dimensions in pixels (so many pixels wide by so many pixels high). if going through a RIP, specify that too.
    A screen shot of your settings or of the image could be very helpful too,
    etc.,
    someone may be able to help you (not necessarily this poster, who is not a Windows user).
    Please read this FAQ for advice on how to ask your questions correctly for quicker and better answers:
    http://forums.adobe.com/thread/419981?tstart=0
    Thanks!

  • Exchange 2010 SP3 /PrepareAD failing; "A reboot from a previous installation is pending. Please restart the system..." error

    I am attempting to prepare our Exchange 2010 Server (RTM) for an upgrade to SP3.
    When attempting to run "setup.com /PrepareAD" to prep the AD schema, the command fails and I receive the following error in the ExchangeSetup log:
    [12/19/2013 21:50:48.0650] [1] Beginning processing Get-OrganizationConfig
    [12/19/2013 21:50:48.0665] [1] Searching objects of type "OrganizationConfig" with filter "$null", scope "SubTree" under the root "$null".
    [12/19/2013 21:50:48.0806] [1] Previous operation run on domain controller 'DC1.company.com'.
    [12/19/2013 21:50:48.0806] [1] Preparing to output objects. The maximum size of the result set is "unlimited".
    [12/19/2013 21:50:49.0945] [1] Ending processing Get-OrganizationConfig
    [12/19/2013 21:51:42.0753] [1] [REQUIRED] A reboot from a previous installation is pending. Please restart the system and rerun setup.
    [12/19/2013 21:51:43.0190] [1] Ending processing test-setuphealth
    [12/19/2013 21:51:43.0221] [0] The Exchange Server setup operation didn't complete.  More details can be found in ExchangeSetup.log located in the <SystemDrive>:\ExchangeSetupLogs folder.
    [12/19/2013 21:51:43.0283] [0] End of Setup
    I am receiving this error when attempting to run "setup.com /PrepareAD" from either of our two GCs and I get the same error from both GCs, so the issue doesn't appear to be related to the individual servers.
    What should I be checking, to clear this error so the AD schema update can be performed?
    Environment
    Exchange:  Exchange Server 2010 RTM
    Server: Windows 2008 R2 (fully patched)
    Domain and Forest functionality: Windows 2008 R2 native

    One follow up:
    If I go into regedit, I see that under HKLM\System\CurrentControlSet\Control\Session Manager  there is an entry from when I recent installed Google Chrome.
    The entry looks like:
    MultiString: PendingFileRenameOperation
    Value Data: \??\C:\Program FIles (x86)\Google\Chrome
    Is this "pending rename" what's causing SP3 to refuse to install, because it thinks the OS install state isn't 'clean'?

  • Device object not present,restart the system and run setup again????

    i install window xp sp2 in my macbook,when i  install driver by mac os cd,installation run until sigmatel,it show error,the my mbp will restart automatically,and the driver installion not complete!! i try to install sigmatel idt sound driver manually,when system update the hardware configuration,it show an error  message
    " device object not present,restart the system and run setup again"!!!!  so i can not fully install bootcamp driver in window!
    any can help??
    macbook pro 13" 2010 mid

    Hi:
    Your notebook is not supported by HP for Windows XP.
    Please read the XP downgrade guide at the link below for instructions on how to get your audio to work in XP.
    http://h30434.www3.hp.com/t5/Notebook-Operating-systems-and/General-XP-Downgrade-Guide-for-HP-Laptop...
    The specific instructions for your model series can be found in the section titled  3. Difficult Models
    Paul

  • I have successfully downloaded lion, and after I click restart, the message " you hard disc is corrupted and cannot be repaired. Please restart" keeps looping. Help !

    I have successfully downloaded lion, and after I click restart, the message " you hard disc is corrupted and cannot be repaired. Please restart" keeps looping. Help !

    First try restarting your Mac into "safe mode", which will run the equivalent of a Disk Utility "repair disk" operation.  If your Mac shuts down during that process, you'll have to try something a little more powerful (and more expensive), such as DiskWarrior.

  • "Configuration changed. Restart the system" and then reboot on startup.

    I have disabled WiMax in BIOS setup and now my x121e doesn't boot at all - just says that "Configuration changed. Restart the system" and reboots. When i press F1 to access bios setup - nothing happens. CMOS reset didn't help/

    In service center they said that motherboard is glitchy and needs replacement.
    So it was a hardware fault.

  • Saved passwords disappeared after forced reboot of the system.

    As I said. After force reboot of the system the list of all my passwords was cleaned up. Bookmarks are ok. FF was closed, before reboot. Any ideas how to return them ?

    Hi Ishini,
    No problem. Firefox would not keep a back up of "key3.db" anywhere. So, if you want to recover your passwords, try to use the following tool.
    * [https://www.piriform.com/recuva Piriform Recuva]
    Just download the free trial and attempt to recover the "key3.db" file. Just point it to your Firefox installation directory.
    This should solve your problem, but there is no guarantee that the file will be there.
    So, if this helped, mark it as helpful, so other users who are facing the same or similar issues, can resolve their problem as well.
    Have a good one,
    Michael.

Maybe you are looking for