No Devices Found (Input and Output) After 10.9.3 Update

Hi,
I just update my Macbook Air (Mid 2013) to 10.9.3. After I finsih updating, I got a problem of no sound at all. Also when I check on System Preferences it shows that "No (Input/Output) device found".
When I try changing the volume using the volume control key on my keboard it shows this image,
I already tried doing some audio bug "fix" trick like reboot, deleting BezelService Preference File, and reset PRAM. However, nothing work.
I am not sure whether I have to reinstall just the audio driver or anything. Audio bug has always been an issue for me since I update to Mavericks.
Could anyone help?
Thanks!

Hey Tetsukara,
Thanks for the question. It looks like you have already done some great troubleshooting on this issue. I would recommend following the steps in this resource:
Troubleshooting issues with no audio from built-in speakers on Macs
http://support.apple.com/kb/ts1574
If your issue persists, you can follow the steps to contact Apple support or obtain service:
5. If the issues persist, contact Apple support for further troubleshooting assistance.
You can obtain service (if needed) through an Apple-Authorized Service Provider or Apple Retail Store. If you plan to visit an Apple Retail store please make a reservation at the Genius Bar using http://www.apple.com/retail/geniusbar/ (available in some countries only).
Thanks,
Matt M.

Similar Messages

Input and output on same device, producer/consumer structure

Hello interested people,
I have a question about using the same device for both digital inputs
and outputs. I have written a simple program of one while loop
that continuously polls the device, processes, and requests. I
have addressed the device using two DAQmx Asst. and I have attached
them with their error in/out cluster terminals to provide data flow and
eliminate the chance of addressing the devices at the same time (which
produces an error). Now I want to change this program structure
to a producer/consumer loop foundation with state machine.
In this design, I will have the DI in the producer loop and the DO in
the consumer loop, under one of the states. I can't simply
connect the error in/out ports in this configuration, so my question is
how to avoid the error caused by addressing the same device
simultaneously with two different tasks (input and output)? I
have attached two VI's, the "One Loop" vi is the original configuration
(simplified), and the Producer-Consumer vi is a NONSENSICAL program
that simply represents the desired configuration. (I don't need
any comments on the programming of this vi, it is only an example for
illustration of the problem).
I am thinking about bundling the input data and the error cluster, both
from the PXI 6528 DI, into one cluster, queueing that up, and
unbundling the de-queued elements for some kind of data flow between
the producer loop and the "Request" state of the consumer loop.
Is this the right approach, or am I barking up the wrong tree?
Thanks
Attachments:
One Loop DO DI.vi ‏102 KB
Producer-Consumer DI-DO.vi ‏106 KB

Hello,
It sounds to me like you really have two modes:
1. user interface actions determine execution
2. user interface is locked, and execution is automated.
I think it would make sense to use the producer consumer for an architecture. Basically you would do the following:
1. program the producer to handle the user interface as you normally would.
2. provide one additional event case in the producer which would be your "automated handling" case. In that case, you could put a state machine which could run until whatever conditions were met to put your program back in "user interface mode".
Keep in mind that you can use custom USER EVENTS to programmatically generate events ie. you can trigger the start of your "automated handling" form anywhere in your code at virtually any time.
I think this would allow you to take advantage of the producer consumer architecture in its intended spirit, while integrating an automated routine.
I hope this helps!
Best Regards,
JLS
Best,
JLS
Sixclear

How to control (the input and output) EXE file after I call it using exec?

Hi,
I knew that I can use runtime.exec() to call one EXE file, and this works. But this EXE has two characteristics:
1. After this exe starts, it asks user to input number such as 1 or 2 onto computer screen, then press return. Then the exe will start the calculation.
2. after it starts calculation, it prints 3 columns of numbers onto the screen.
My two questions are:
1. How to use java to input the number such as 1 or 2 automatically? this EXE can not work like this in DOS command line:
C:> file.exe parameter
The parameter is the number such as 1 or 2 that I wanna input.
2. how to redirect the 3 columns of numbers from computer screen to txt file?
My colleague can solve these two questions using Mathematica. So I know that definitely there is at least one solution for it. I just can not do it using Java. This wierd exe file bothered me a lot and I really wish that I can get help from someone in java community.
Thank you!
Tony

When you call Runtime.exec, you get a Process object. (I presume something similar happens when you use ProcessBuilder.) Process has methods with names getOutput, getInput, and getError. These correspond to the standard input, standard output, and standard error streams of the spawned process.
You can read and write to the process on the streams corresponding to input and output that the process writes to the console.
[add]
In fact, you should be grabbing and reading the output/error streams anyway, because of the points raised by the Traps article. Google "Java Runtime exec traps" and you'll probably get a link to this JavaWorld article, which describes common Runtime.exec problems and how to solve them.
Edited by: paulcw on Jun 15, 2010 4:09 PM

Selecting separate input and output devices!

hi, i have logic pro 8 and cant find out how to select separate devises for input and output!
for my output (and input when recording drums) i use a alesis multimix 16 (16 track firewire desc) but for recording guitars and bass and poss vocals i would like to use my line 6 x3 live as my input devise but still using the alesis for monitoring.
is this possible? cant figure how to do it.
any help is great help! cheers, Dan

In Logic 9 you can easily select different input and output devices in the Preferences Devices area. In Logic 8 you must create an aggregate device -
http://support.apple.com/kb/HT1215
JG

I'm trying to record in Adobe Audition and it keeps saying my the sample rates for my input and output devices do not match. How do I correct this?

I'm trying to record in Audition and it keeps saying my sample rates for the input and output devices don't match. How do I fix this?

I finally have communication between the ISA One and Audition. I moved the optic cable to another SPDIF on the computer and from the SPDIF to ADAT on the ISA One and it finally agreed that the communication was at the same clock speed. The audio was not intelligible so I moved the optic cable back to the original configuration and I can record voice that is clean.

I have a 2007 iMac connected via WiFi. It has been working fine until I turned it on after a recent vacation. Network preferences indicates that it is correctly connected to my WiFI system but the data input and output rate is virtually zero. I know that

I have a 2007 iMac connected via WiFi. It has been working fine until I turned it on after a recent vacation. Network Preferences indicates that it is correctly connected to my WiFI system but the data input and output rate is virtually zero. I know that the WiFI signal is reaching the iMac since both my iPhone and iPad are working perfectly at that location. I have rebooted the router and the iMac to no avail. Any suggestions would be greatly appreciated. Thank you very much. Geoff

Hi Geoff,
Hi, this has worked for a few...
Make a New Location, Using network locations in Mac OS X ...
http://support.apple.com/kb/HT2712
10.7 & 10.8…
System Preferences>Network, top of window>Locations>Edit Locations, little plus icon, give it a name.
10.5.x/10.6.x/10.7.x instructions...
System Preferences>Network, click on the little gear at the bottom next to the + & - icons, (unlock lock first if locked), choose Set Service Order.
The interface that connects to the Internet should be dragged to the top of the list.
10.4 instructions...
Is that Interface dragged to the top of Network>Show:>Network Port Configurations.
If using Wifi/Airport...
Instead of joining your Network from the list, click the WiFi icon at the top, and click join other network. Fill in everything as needed.
For 10.5/10.6/10.7/10.8, System Preferences>Network, unlock the lock if need be, highlight the Interface you use to connect to Internet, click on the advanced button, click on the DNS tab, click on the little plus icon, then add these numbers...
208.67.222.222
208.67.220.220
Click OK.

Synchronize input and output tasks to start at the same sample point [C++ NI_DAQmx Base]

I'm trying to initiate the analog input and output streams to start reliably at the same sample. I've tried triggering the output from the start of the input using the following code [NI-DAQmx Base 2.1 under Mac OS X with an M-Series multifunction board]. It compiles and runs, but gives an error message at the call to "DAQmxBaseCfgDigEdgeStartTrig". Any suggestions about synchronized I/O on this platform?
#include "NIDAQmxBase.h"
#include
#include
#include
#define DAQmxErrorCheck( functionCall ) { if ( DAQmxFailed( error=( functionCall ) ) ) { goto Error; } }
int main( int argc, char *argv[] )
// Task parameters
int32 error = 0;
TaskHandle inputTaskHandle = 0;
TaskHandle outputTaskHandle = 0;
char errorString[ 2048 ] = {'\0'};
int32 i;
time_t startTime;
// input channel parameters
char inputChannelList[] = "Dev1/ai0, Dev1/ai1";
float64 inputVoltageRangeMinimum = -10.0;
float64 inputVoltageRangeMaximum = 10.0;
// output channel parameters
char outputChannelList[] = "Dev1/ao0, Dev1/ao1";
char outputTrigger[] = "Dev1/ai/StartTrigger";
float64 outputVoltageRangeMinimum = -10.0;
float64 outputVoltageRangeMaximum = 10.0;
// Timing parameters
char clockSource[] = "OnboardClock";
uInt64 samplesPerChannel = 100000;
float64 sampleRate = 10000.0;
// Input data parameters
static const uInt32 inputBufferSize = 100;
int16 inputData[ inputBufferSize * 2 ];
int32 pointsToRead = inputBufferSize;
int32 pointsRead;
float64 timeout = 10.0;
int32 totalRead = 0;
// Output data parameters
static const uInt32 outputBufferSize = 1000;
float64 outputData[ outputBufferSize * 2 ];
int32 pointsToWrite = outputBufferSize;
int32 pointsWritten;
for( int i = 0; i < outputBufferSize; i++ )
outputData[ 2 * i ] = 9.95 * sin( 2.0 * 3.14159 * i / outputBufferSize );
outputData[ 2 * i + 1 ] = -9.95 * sin( 2.0 * 3.14159 * i / outputBufferSize );
// ------------------- configure input task -----------------------
DAQmxErrorCheck ( DAQmxBaseCreateTask( "", &inputTaskHandle ) );
printf( "Created input task\n" );
DAQmxErrorCheck ( DAQmxBaseCreateAIVoltageChan( inputTaskHandle, inputChannelList, "", DAQmx_Val_RSE, inputVoltageRangeMinimum, inputVoltageRangeMaximum, DAQmx_Val_Volts, NULL ) );
printf( "Created AI Voltage Chan\n" );
DAQmxErrorCheck ( DAQmxBaseCfgSampClkTiming( inputTaskHandle, clockSource, sampleRate, DAQmx_Val_Rising, DAQmx_Val_ContSamps, samplesPerChannel ) );
printf( "Set sample rate\n" );
// ------------------- configure output task -----------------------
DAQmxErrorCheck ( DAQmxBaseCreateTask( "", &outputTaskHandle ) );
printf( "Created output task\n" );
DAQmxErrorCheck ( DAQmxBaseCreateAOVoltageChan( outputTaskHandle, outputChannelList, "", outputVoltageRangeMinimum, outputVoltageRangeMaximum, DAQmx_Val_Volts, NULL ) );
printf( "Created AO Voltage Chan OK\n" );
DAQmxErrorCheck ( DAQmxBaseCfgSampClkTiming( outputTaskHandle, clockSource, sampleRate, DAQmx_Val_Rising, DAQmx_Val_ContSamps, samplesPerChannel ) );
printf( "Set sample rate\n" );
// trigger output when input starts
DAQmxErrorCheck ( DAQmxBaseCfgDigEdgeStartTrig( outputTaskHandle, outputTrigger, DAQmx_Val_Rising ) );
printf( "Set output trigger\n" );
// ------------------- configuration -----------------------
// write output signal
DAQmxErrorCheck ( DAQmxBaseWriteAnalogF64( outputTaskHandle, pointsToWrite, 0, timeout, DAQmx_Val_GroupByScanNumber, outputData, &pointsWritten, NULL ) );
printf( "Write output signal\n" );
// set up input buffer
DAQmxErrorCheck ( DAQmxBaseCfgInputBuffer( inputTaskHandle, 200000 ) ); // use a 100,000 sample DMA buffer
// initiate acquisition - must start output task first
DAQmxErrorCheck ( DAQmxBaseStartTask( outputTaskHandle ) );
DAQmxErrorCheck ( DAQmxBaseStartTask( inputTaskHandle ) );
// The loop will quit after 10 seconds
Dr John Clements
Lead Programmer
AxoGraph Scientific

Hi Michael,
First of all, thanks very much for taking the time to investigate this problem! Much appreciated.
You asked for "an actual error code you got and any description that is given". The full output from the program that I posted earlier in this thread is appended to the end of this message. In summary, following the call to...
DAQmxErrorCheck ( DAQmxBaseCfgDigEdgeStartTrig( outputTaskHandle, outputTrigger, DAQmx_Val_Rising ) );
... with ...
char outputTrigger[] = "Dev1/ai/StartTrigger";
...the error message is ...
DAQmxBase Error: Specified route cannot be satisfied, because the hardware does not support it.
You asked "specifically which M series device you are using"? It is the PCIe 6251 (with BNC 2111 connector block). I'm testing and developing on an Intel Mac Pro (dual boot OS X and Windows XP).
You asked for "the location you pulled the code from". Here it is...
http://zone.ni.com/devzone/cda/epd/p/id/879
...specifically from the file "Multi-Function-Synch AI-AO_Fn.c".
I adapted the NI-DAQmx calls to their NI-DAQmx Base equivalents.
Finally, you asked "Is the trigger necessary, or do you just need to know that the measurements are running on the same clock?". I believe that some kind of sychronized trigger is necessary in my situation (correct me if I'm wrong). Timing is crucial. Say I initiate an analog output stream that delivers a voltage command step 5 ms from the onset. I need to record the response (analog input stream) so that its onset is accurately aligned (synchronized) at 5 ms. A typical recording situation would stimulate and record a short data 'sweep', then wait for the (biological) system to recover, then stimulate and record another short sweep, and repeat. I need all the recorded sweeps to align accurately so that they can be averaged and analyzed conveniently.
I definitely do not want my customers to rely on an expensive external TTL pulse generator to initiate and synchronize each 'sweep'. That would effectively eliminate the cost advantage of an NI board, as well as adding unnecessary complexity in setup and use. It would be a show-stopper for me.
It seems perverse, but would it be possible to use a digital output channel connected directly to a digital input chanel to trigger the input and output streams?
Regards,
John.
Full output from test program. Compiled with gcc 4 under OS X...
[Session started at 2007-05-23 14:17:01 +1000.]
LoadRuntime: MainBundle
CFBundle 0x303cc0 (executable, loaded)
_CompatibleWithLabVIEWVersion: linkedAgainst: 08208002
_CompatibleWithLabVIEWVersion: result= false, mgErr= 1, theActualVersion= 00000000
_CompatibleWithLabVIEWVersion: linkedAgainst: deadbeef
_CompatibleWithLabVIEWVersion: Reseting Linked Against
_CompatibleWithLabVIEWVersion: linkedAgainst: 08208002
_CompatibleWithLabVIEWVersion: result= true, mgErr= 0, theActualVersion= 00000000
_CompatibleWithLabVIEWVersion: linkedAgainst: 08208002
_CompatibleWithLabVIEWVersion: result= true, mgErr= 0, theActualVersion= 00000000
com.ni.LabVIEW.dll.nidaqmxbaselv
CFBundle 0x313760 (framework, loaded)
{type = 15, string = file://localhost/Library/Frameworks/nidaqmxbaselv.framework/, base = (null)}
Amethyst:Library:Frameworks:nidaqmxbaselv.framework
2007-05-23 14:17:02.248 test-ni[4445] CFLog (21): Error loading /Library/Frameworks/LabVIEW 8.2 Runtime.framework/resource/nitaglv.framework/nitaglv: error code 4, error number 0 (no suitable image found. Did find:
/Library/Frameworks/LabVIEW 8.2 Runtime.framework/resource/nitaglv.framework/nitaglv: mach-o, but wrong architecture)
CFBundle 0x1751fdc0 (framework, not loaded)
Created input task
Created AI Voltage Chan
Set sample rate
Created output task
Created AO Voltage Chan OK
Set sample rate
DAQmxBase Error: Specified route cannot be satisfied, because the hardware does not support it.
test-ni has exited with status 0.
Dr John Clements
Lead Programmer
AxoGraph Scientific

TTYA Input and Output

Hi All,
I am new to this forum as well as new to SUN.
I tried to boot a Sun Blade 100. The message that appears on the screen is Keyboard not found. use ttya Input and Output.
I have only a normal MS Keyboard which cannot be connected to SUN. Do we need to have a special Keyboard. Whether we have to use USB Keyboard...
I just want to know more about TTYA input and output.
Thanx.

Hi Martin
Thanx for your info.I Connected using a second computer that has a serial port as well as a null-modem connection cable.
The following appears in the second computer..I am not able to type anything from the second computer keyboard..Is there any reason for it..?
Sun Blade 100 (UltraSPARC-IIe), No Keyboard
Copyright 1998-2003 Sun Microsystems, Inc. All rights reserved.
OpenBoot 4.10.6, 512 MB memory installed, Serial #51719739.
Ethernet address 0:3:ba:15:2e:3b, Host ID: 83152e3b.
Boot device: disk File and args:
Bad magic number in disk label
Can't open disk label package
Evaluating:
Can't open boot device
Type boot , go (continue), or login (command mode)
>

Synchronisation of input and output using myDAQ

Hello!
I am currently using the NI myDAQ and use both analoge output. and both analoge inputs. The sampling rate needs to be as high as 200k Hz. (Also within the while loop I do quite a lot of data manipulation and saving into text files.) My vi works generally fine, but I still have to problems:
1. How can I ensure that the read and write tasks are synchronised? I found out that it is not possible to use other trigger than the sample clock for write and read tasks using the myDAQ. (Is this right?) So as a workaround for me it is not important that the tasks start at the same time, but I want to ensure that the delay between "Start Write Task" and "Start Read Task" always is the same. Is this possible? And how can I realise it?
2. If I want to generate a non periodical signal that is not constant, how do I best generate this? At the moment I use a Sine Waveform.vi with a frequency of 0 and I change the offset input with every loop. I also tried to use the FormulaWaveform.vi but with this my produced waveform seemed to stop after completing the "number of samples in the waveform". But the sampling info must be the same for both AO channels I use, so I cannot simply increase this number.
Thanks a lot for any help! Jules
Attachments:
MyDAQReadWrite.vi ‏72 KB

hi Jules,
If you only want to ensure that the delay between "Start Write Task" and "Start Read Task" always is the same, you can realize it with a simple while loop (with Wait Until Next ms Multiple).
But if you want to synchronize for example both analog input, you can see how it works in different examples. Following Path is shows you how to find these examples:
In LabVIEW -> Help -> Find Examples... Brows(Brows according to Task): Hardware Input and Output -> DAQmx -> Synchronization -> "Analog Input Synchronizantion.vi"
To generate a non periodical signal that is not constant, you can change the offset input every loop. If you want to manipulate the offset while running you can also use local variables in the loop.
In this case you could manipulate for example with a slide control.
Regards,
grroesis

Synchronizing analog input and output

I am in the middle of converting some Traditional NI-DAQ code to the
DAQmx API (I am using C++). Most of it is going quite well: my
code complexity has been greatly reduced and (since upgrading to 7.4)
my CPU usage has plummeted. However, in one particular case I
need my input and output buffers to be synchronized. I.e. sample
0 of my input buffer should be read at the same instant sample 0 of my
output buffer went out on the line. In Traditional NI-DAQ, I
synchronized my input and output start triggers using the following
method (which I believe I found in an example somewhere):
error = Select_Signal(addr, ND_PFI_6, ND_OUT_START_TRIGGER, ND_LOW_TO_HIGH);
error = Select_Signal(addr, ND_IN_START_TRIGGER, ND_PFI_6, ND_LOW_TO_HIGH);
This then allowed me to setup my input thread, then initialize
everything in my output thread and when my output got the start
command, so did my input. The result was that I could perfectly
match buffers of output data to buffers of input data (after taking all
the appropriate buffering into account).
When I try the same method with the DAQmxConnectTerms function, my
buffers don't line up. They are off by 15-20 ms out of a 400ms
buffer (sampling at 10kHz). I tried cutting out the middle man of
PFI6 with similar results. So my current "synchronize" block
looks like this:
error = m_fnConnectTerms("/Dev1/ao/StartTrigger", "/Dev1/ai/StartTrigger", 0);
I get no error. This also seems to cause my output loop to hang
after a few seconds, although that could be a side effect of something
else that I haven't tracked down yet. Is there a better way to do
what I'm trying to do here? Perhaps it is a misunderstanding of
the way buffering works on the M series cards (I am currently using a
6221).

Don't use Connect Terminals. Use the technique shown in this example program
C:\Program Files\National Instruments\NI-DAQ\Examples\DAQmx ANSI C\Synchronization\Multi-Function\ContAI-Read Dig Chan
which is the sharing of sample clocks via the DAQmxCfqSampClkTiming function where the sample clock source of one task is set to the clock of the other task. This example slaves a digital input task to an analog input task but the idea is the same for your application.

How can I use a different driver for audio input and output?

I did a search of course, and came up with something about an aggregate. I have no idea what this is, how to do it, or if it would even work for me.
What I am trying to do is:
1) Record into Logic Express using my Tascam US-122.
2) Have playback come out of my computer sound system, not the Tascam.
If I go over to the Audio setup window, I can only record when the driver is set to Tascam US-122. Likewise, I can only listen to sound when my Built-In Audio is selected. It gets rather annoying going between the two.
So, would this aggregate thing solve my problem? If so, how do I do it? Thanks for any help!
-allen

Yes it should do what you want.
Go to "Audio Midi Setup", and go to the Audio menu and click "Open Aggregate Device Editor". The interface is pretty simple but if you do get stuck, just use the help function in Audio Midi Setup, as it has a step by step guide.
Then when you return to logic, go to the Preferences>Audio>Drivers section and select Aggregate Device as the new driver rather than either the built in sound or the tascam. Then the inputs and outputs will apply to BOTH devices.

SSIS: How to use one Variable as Input and Output Parameter in an Execute SQL Task

Hello,
i need your help,I'm working on this issue since yesterday and have no idea how to deal with it.
As I already said in the tilte i want to start a stored procedure via a Execute SQL Task which has around 15 prameters. 10 of these should be used as input AND output value.
As an example:
i have three Variable:
var1    int        2
var2    int     100
var3    int     200
the stroed procedure:
   sp_test
     @var1 int
      @var2 int output
      @var3 int output
   AS
   BEGIN
        SET @var2 = @var2 * @var1
        SET @var3 = @var3 + @var1
   END
So in the Execute SQL Task i call the Stored Procedure as follwos:
    Exec sp_test  @var1 = ?, @var2 = ? output, @var3 = ? output
(I use an OLE DB Connection)
The parameter mapping is as follows:
User::Var1        input                   numeric              0                 -1
User::Var2        input/output         numeric              1                 -1
User::Var3        input/output         numeric              2                 -1
Now my problem. If i set  Var2 and Var3 as Input parameter the values are still the same after running the package. If i set them to a output value the are both Null because the procedure doesnt get any values.
I already tried to list them a second time - like
    User::Var2        input                  numeric              1                 -1
    User::Var2        output                 numeric              1                 -1
or i use a new variable
    User::Var2                  input                  numeric              1                 -1
    User::Var2Return        output                 numeric              1                 -1
but i alwas get the error
"Multiple-step OLE DB operation generated errors. Check each OLE DB status value, if available. No work was done."
Has anybody an idea how I can solve this problem?
Thanks a lot.
Kind Regards,
Alice

Hi Alain,
thx for your answer.
I have around 15 procedures called one after the other to calculated and modify my values. Each procedure is responsible for an other but overlapping set of variables. So i thought it would be a good idea to call them one after the other with the needed variables via a execute sql task.
So if i use a result set, how i get my stored procedure to return 10 values? I would have to use a Function instead of a procedure, wouldn't i?
As if i have 15 procedures this would be a lot of work.
But thanks a lot for the idea. I think an other idea would be to create one function which calls all stored procedures and returns all the calculated values as a result set, wouldn't it?.
Kind Regards.
Alice

How to use a bluetooth cellphone for audio input and output

Hello, I was wondering how to set-up my Mac Book so that I can use my bluetooth cellphone for audio in and audio out. Ideally, I would like to use my handset for talking on iChat and Skype. Has anyone had any luck doing this? When I bond my cellphone these optiosn do not appear. I know that this is easy to do on a Windows machine but I am not sure about how to do it on my Mac Book.
Thanks!

Yes it should do what you want.
Go to "Audio Midi Setup", and go to the Audio menu and click "Open Aggregate Device Editor". The interface is pretty simple but if you do get stuck, just use the help function in Audio Midi Setup, as it has a step by step guide.
Then when you return to logic, go to the Preferences>Audio>Drivers section and select Aggregate Device as the new driver rather than either the built in sound or the tascam. Then the inputs and outputs will apply to BOTH devices.

How do I create an xControl with multiple inputs and outputs?

Hello,
i am trying to write a new Xcontrol Element. In the data model I can create data types using the cluster to create compound types, eg an int and an int array. But how do I create an xcontrol which has multiple data inputs and outputs?
Kind Regards

Limping_Twerp wrote:
Alright: I see: An xcontrol is either an input OR an output. How do I achieve an output? Secondly: So you are saying the only Elements that can have multiple inputs and outputs are VIs?
Can you take a few steps back and explain what you are actually trying to do. SubVIs and Xcontrols have nothing in common and it is not clear why you even try to compare them side by side (e.g. in terms of the number of connectors).
Your questions about input or output tell us that you seems to have some misconceptions about xcontrols. Xcontrols are like regular controls, except they have some built-in intelligence that you can program. Most front panel object can be either controls or indicators and the same is true for Xcontrol. You create an Xcontrol, and after placing it on the front panel you can decide if it should be a control (where the code reads the value) or an indicator (were the code writes values to it). When you define the xcontrol facade, you also need to program how the visuals change if it is changed from control to indicator or vice versa.
As a first step, you should opend the example finder and look at some xcontrol examples.
Again, what are you actually trying to do?
LabVIEW Champion . Do more with less code and in less time .

FINALLY INPUTTING and OUTPUTTING Annotations!

Ok, before everyone thinks that this is a very bad solution, I have to tell that I`m no programmer and my knowledge of PostgreSQL, Ruby or any other language is very poor.
With useful help from Jamie Hodge, fbm and Nicholas Stokes (mainly)
I could manage to write a command for inputting and outputting from Final Cut Server Annotations.
So lets go to the fun part:
INPUTTING:
1- Create a Response called "Annotations IN" (or whatever you want):
a - Reponse Action: "Run an external script or command"
b - Run Script > *Commnad Path: /Library/Application Support/Final Cut Server/Final Cut Server.bundle/Contents/Resources/sbin/fcsvr_run
Command Parameters: psql px pxdb -c "COPY pxtcmdvalue FROM '/FCSRV/annotation-in.txt' USING DELIMITERS '|';"
2 - Create a poll Watcher with name: "Watch for Annotations IN"
a - Enable: true
b - Monitor Address: Chooses a Device (create a new one or use a tmp one) and path to where you`ll going to put a txt file with the annotations.
c - Response List: Choose the Response you created "Annotations IN" in my case.
d - Event Type Filter: Created, Modified
e - Poll Watcher > Listing Frequency: 2 (or any number of seconds you feel like it).
Listing multiple: 2
Wildcard include Filter: *.txt (or any custom extensions you want)
3 - Create a txt file and use this as a template:
{ASSET_ENTITYID}|1527|{TCIN}/(30000,1001)|{TCOUT}/(30000,1001)|{Annotation}|{USE RID}|{DATE}
Where:
{ASSET_ENTITYID} = Is the entityid of your asset. You can find what number it is by issuing:
/Library/Application\ Support/Final\ Cut\ Server/Final\ Cut\ Server.bundle/Contents/Resources/sbin/fcsvr_run psql px pxdb -c "SELECT pxmdvalue.entityid, pxmdvalue.value AS asset_name FROM pxmdvalue INNER JOIN pxentity ON pxentity.entityid = pxmdvalue.entityid WHERE pxmdvalue.fieldid='1543' AND pxentity.address LIKE '/asset/%';"
This will output ALL your assets, so if you know the name or want to parse the name you can use:
/Library/Application\ Support/Final\ Cut\ Server/Final\ Cut\ Server.bundle/Contents/Resources/sbin/fcsvr_run psql px pxdb -c "SELECT pxmdvalue.entityid, pxmdvalue.value AS asset_name FROM pxmdvalue INNER JOIN pxentity ON pxentity.entityid = pxmdvalue.entityid WHERE pxmdvalue.fieldid='1543' AND pxmdvalue.value='ASSETNAME' AND pxentity.address LIKE '/asset/%';"
Where in ASSETNAME you`ll have to put your Asset Name without extension.
{TCIN} and {TCOUT} is, of course, the TC`s points. In the form of: HH:MM:SS;FF
{Annotation} is the commentary.
{USERID} (in my case was 1)
{DATE}: This one is tricky. My example is 2009-03-15 19:31:15.839795-03
So is in the form YYYY-MM-DD HH:MM:SS.????? I really don`t know the rest. Could be milliseconds?
Of course one can write a script to translate everything from a txt file like:
ASSETNAME | TCIN | TCOUT | ANNOTATIONS | USER
But as I`ve said I`m no programmer
Ok.. now the time for the OUTPUT:
The command-line is:
/Library/Application\ Support/Final\ Cut\ Server/Final\ Cut\ Server.bundle/Contents/Resources/sbin/fcsvr_run psql px pxdb -c "SELECT pxmdvalue.value AS Asset_NAME, pxtcmdvalue.value, pxtcmdvalue.begintc, pxtcmdvalue.endtc FROM pxmdvalue INNER JOIN pxtcmdvalue ON pxmdvalue.entityid = pxtcmdvalue.entityid WHERE pxmdvalue.value='ASSETNAME';"
Where ASSETNAME is the Asset name without the extension.
Or issuing the following to OUTPUT ANNOTATIONS from ALL assets:
/Library/Application\ Support/Final\ Cut\ Server/Final\ Cut\ Server.bundle/Contents/Resources/sbin/fcsvr_run psql px pxdb -c "select * from pxtcmdvalue;"
Adding "> /PATHTO_WHERE_IN_WANT/ANNOTATIONSOUTPUT.TXT" at the end will put all output into a txt file.
It`s possible (in theory) to:
1- Create a boolean md field in FCSRV called "EXPORT Annotations" (don`t choose lookup)
2- add or create a md group called "Export Annotations" and add the above md field to it (don`t choose lookup)
3- Add "Export Annotations" md field to Asset Filter md group
4- Make a Response for Running external command. Command path: /Library/Application Support/Final Cut Server/Final Cut Server.bundle/Contents/Resources/sbin/fcsvr_run
Command Parameters: psql px pxdb -c 'SELECT pxmdvalue.value AS Asset_NAME, pxtcmdvalue.value, pxtcmdvalue.begintc, pxtcmdvalue.endtc FROM pxmdvalue INNER JOIN pxtcmdvalue ON pxmdvalue.entityid = pxtcmdvalue.entityid WHERE pxmdvalue.value=[FileName];' > ~/Desktop/ann-out.txt
(I`m having problem with this, it doesn`t work).
5- Make a Subscription that if Export Annotations modified = true, trigger if changed and trigger the Response above.
6- Add exporting annotations md group to Media md set.
In theory it`s possible to modify the FinalCutServerIntegrationSample get and input annotations instead of adding another "comment" field to md group list.
Few!
Ok so please help beautify this out!
This will be very useful for a lot of people.... We know that it`s only a matter of time to FCSVR have this function built-in... but this "time" could be years.
So let`s start ourselves!
Thank you very much!!
Regards!

AlphaBlue wrote:
jverd wrote:
What were you hoping for? Someone reading your mind for what exactly you need, and handing you a giftwrapped answer, without you doing any work or clearly communicating a specific problem? This site doesn't really work that way.Fair enough. I'm asking for insight into how to input from and output to a StarOffice Spreadsheet into/from a Java program. (Think java.io except with spreadsheet files instead of .txt files.) I already answered that question.
I need to accomplish this without the use of a community-created library.That's a bizarre requriement. Why?
>
Okay, [here you go|http://lmgtfy.com/?q=communication+between+StarOffice+Spreadsheets+and+Java].
If you don't have any knowledge or experience, on the matter, please refrain from directing me to a google search. I assure you, I have already performed such a task.How would I know that.
But okay, let's say I know that. Let's say you bothered to point out that you've already done that. Further, let's say I do have knowledge of the subject at hand. Maybe I'm an expert. Maybe I wrote Star Office and an open source library (which wheel for some reason you must reinvent). You are assuming that I also have psychic powers, so that I can read your mind and know exactly what you've read so far and exactly what parts of your very broad and vague question said reading did not answer.
In short, you have received answers commensurate with your questions.

No Devices Found (Input and Output) After 10.9.3 Update

Similar Messages

Maybe you are looking for