No Disks Found!  error during install of Solaris10 R10 on OracleVM 3.0.1

Has anybody got Solaris 10 R10 working in OracleVM 3.0.1? I have Linux 6.1 and Solaris11 working fine. But get no disks found during iso install of Solaris10 R10.

Still no luck, I get through the installation until it asks about CDROM media, then I get a pop up window with the "No Disks found" eror, after that the install exists to xterm window.
Here's my vm.cfg in this instance I did not change xvd to hd as all my attempts to change this cause vm not to boot.
-thanks for any advise.
memory = 2048
disk = ['file:/OVS/Repositories/0004fb0000030000914c5da5cda46bfc/ISOs/0004fb0000150000cb99f253bbdcfffc.iso,xvda:cdrom,r', 'phy:/dev/mapper/3600144f0e863c90000004e7d4b5f0002,xvdb,w!', 'file:/OVS/Repositories/0004fb0000030000914c5da5cda46bfc/VirtualDisks/0004fb000012000049d780014c3c21d4.img,xvdc,w!']
vif = ['mac=00:21:f6:00:00:04,bridge=192.168.0.0']
usbdevice = 'tablet'
on_crash = 'restart'
OVM_description = ''
name = '0004fb000006000092cffa6918b35871'
builder = 'hvm'
on_poweroff = 'destroy'
boot = 'dc'
uuid = '0004fb00-0006-0000-92cf-fa6918b35871'
vfb = ['type=vnc,vncunused=1,vnclisten=127.0.0.1']
on_reboot = 'restart'
vcpus = 2
cpu_weight = 27500
OVM_os_type = 'Oracle Solaris 10'
cpu_cap = 0
OVM_high_availability = True
maxmem = 2048
OVM_simple_name = 'sol10r10'
guest_os_type = 'default'

Similar Messages

  • "No Disk Found" error during installation of Solaris 10[11/06] on HP 6710b

    Hallo Guys,
    I am trying to install Solaris 10 on my HP 6710b lap top but it fails with "No Disk Found" error.
    I used "Solaris 10 support tool" to check my system and it reports that my system is supported.
    You can find the report bellow. I am sure that my disk is OK and I am also using "CD-ROM" option in BIOS for installing solaris from my Solaris DVD.
    I have also updated the drivers using "CPQary3-1.71-solaris10-i386".
    Please help me.
    Thanks,
    Qumar
    Report of Sun Device Detection Tool
    The table below displays the devices detected in your system along with the corresponding driver status in Solaris 10 8/07 on x86/x64 platforms.
    All detected devices are supported by Solaris OS.
    Solaris Driver 32-bit
    Solaris Driver 64-bit
    Device Type
    Vendor Name
    Device Name
    Solaris Bundled Driver: pcic
    Solaris Bundled Driver: pcic
    Bridge
    Ricoh Co Ltd
    RL5c476 II
    Solaris Bundled Driver: hci1394
    Solaris Bundled Driver: hci1394
    Firewire
    Ricoh Co Ltd
    R5C832 IEEE 1394 Controller
    Third-Party Driver: bcme (Note-1)
    Third-Party Driver: bcme (Note-1)
    Network
    Broadcom Corporation
    NetLink BCM5787M Gigabit Ethernet PCI Express
    Solaris Bundled Driver: ahci
    Solaris Bundled Driver: ahci
    Storage
    Intel Corporation
    82801HBM/HEM (ICH8M/ICH8M-E) SATA AHCI Controller
    Solaris Bundled Driver: uhci
    Solaris Bundled Driver: uhci
    USB
    Intel Corporation
    82801H (ICH8 Family) USB UHCI Controller #1
    Solaris Bundled Driver: uhci
    Solaris Bundled Driver: uhci
    USB
    Intel Corporation
    82801H (ICH8 Family) USB UHCI Controller #2
    Solaris Bundled Driver: uhci
    Solaris Bundled Driver: uhci
    USB
    Intel Corporation
    82801H (ICH8 Family) USB UHCI Controller #3
    Solaris Bundled Driver: uhci
    Solaris Bundled Driver: uhci
    USB
    Intel Corporation
    82801H (ICH8 Family) USB UHCI Contoller #4
    Solaris Bundled Driver: uhci
    Solaris Bundled Driver: uhci
    USB
    Intel Corporation
    82801H (ICH8 Family) USB UHCI Controller #5
    Solaris Bundled Driver: ehci
    Solaris Bundled Driver: ehci
    USB
    Intel Corporation
    82801H (ICH8 Family) USB2 EHCI Controller #1
    Solaris Bundled Driver: ehci
    Solaris Bundled Driver: ehci
    USB
    Intel Corporation
    82801H (ICH8 Family) USB2 EHCI Controller #2
    [W] Solaris Bundled Driver: audiohd
    [W] Solaris Bundled Driver: audiohd
    Multimedia
    Intel Corporation
    82801H (ICH8 Family) HD Audio Controller
    Solaris Bundled Driver: pci-ide
    Solaris Bundled Driver: pci-ide
    Storage
    Intel Corporation
    82801HBM/HEM (ICH8M/ICH8M-E) IDE Controller
    [W] Solaris Bundled Driver: vgatext
    [W] Solaris Bundled Driver: vgatext
    Video
    Intel Corporation
    Mobile GM965/GL960 Integrated Graphics Controller
    Open Solaris Driver: wpi (Note-2)
    Open Solaris Driver: wpi (Note-2)
    Network
    Intel Corporation
    PRO/Wireless 3945ABG Network Connection
    [W]: (1) No Dedicated Xorg Driver supporting Graphic Interface
    (2) Driver support for indicated device not guaranteed
    Note-1: http://www.broadcom.com/support/ethernet_nic/.
    Note-2: http://opensolaris.org/os/community/laptop/wireless/wpi.

    Hallo Guys,
    I am trying to install Solaris 10 on my HP 6710b lap top but it fails with "No Disk Found" error.
    I used "Solaris 10 support tool" to check my system and it reports that my system is supported.
    You can find the report bellow. I am sure that my disk is OK and I am also using "CD-ROM" option in BIOS for installing solaris from my Solaris DVD.
    I have also updated the drivers using "CPQary3-1.71-solaris10-i386".
    Please help me.
    Thanks,
    Qumar
    Report of Sun Device Detection Tool
    The table below displays the devices detected in your system along with the corresponding driver status in Solaris 10 8/07 on x86/x64 platforms.
    All detected devices are supported by Solaris OS.
    Solaris Driver 32-bit
    Solaris Driver 64-bit
    Device Type
    Vendor Name
    Device Name
    Solaris Bundled Driver: pcic
    Solaris Bundled Driver: pcic
    Bridge
    Ricoh Co Ltd
    RL5c476 II
    Solaris Bundled Driver: hci1394
    Solaris Bundled Driver: hci1394
    Firewire
    Ricoh Co Ltd
    R5C832 IEEE 1394 Controller
    Third-Party Driver: bcme (Note-1)
    Third-Party Driver: bcme (Note-1)
    Network
    Broadcom Corporation
    NetLink BCM5787M Gigabit Ethernet PCI Express
    Solaris Bundled Driver: ahci
    Solaris Bundled Driver: ahci
    Storage
    Intel Corporation
    82801HBM/HEM (ICH8M/ICH8M-E) SATA AHCI Controller
    Solaris Bundled Driver: uhci
    Solaris Bundled Driver: uhci
    USB
    Intel Corporation
    82801H (ICH8 Family) USB UHCI Controller #1
    Solaris Bundled Driver: uhci
    Solaris Bundled Driver: uhci
    USB
    Intel Corporation
    82801H (ICH8 Family) USB UHCI Controller #2
    Solaris Bundled Driver: uhci
    Solaris Bundled Driver: uhci
    USB
    Intel Corporation
    82801H (ICH8 Family) USB UHCI Controller #3
    Solaris Bundled Driver: uhci
    Solaris Bundled Driver: uhci
    USB
    Intel Corporation
    82801H (ICH8 Family) USB UHCI Contoller #4
    Solaris Bundled Driver: uhci
    Solaris Bundled Driver: uhci
    USB
    Intel Corporation
    82801H (ICH8 Family) USB UHCI Controller #5
    Solaris Bundled Driver: ehci
    Solaris Bundled Driver: ehci
    USB
    Intel Corporation
    82801H (ICH8 Family) USB2 EHCI Controller #1
    Solaris Bundled Driver: ehci
    Solaris Bundled Driver: ehci
    USB
    Intel Corporation
    82801H (ICH8 Family) USB2 EHCI Controller #2
    [W] Solaris Bundled Driver: audiohd
    [W] Solaris Bundled Driver: audiohd
    Multimedia
    Intel Corporation
    82801H (ICH8 Family) HD Audio Controller
    Solaris Bundled Driver: pci-ide
    Solaris Bundled Driver: pci-ide
    Storage
    Intel Corporation
    82801HBM/HEM (ICH8M/ICH8M-E) IDE Controller
    [W] Solaris Bundled Driver: vgatext
    [W] Solaris Bundled Driver: vgatext
    Video
    Intel Corporation
    Mobile GM965/GL960 Integrated Graphics Controller
    Open Solaris Driver: wpi (Note-2)
    Open Solaris Driver: wpi (Note-2)
    Network
    Intel Corporation
    PRO/Wireless 3945ABG Network Connection
    [W]: (1) No Dedicated Xorg Driver supporting Graphic Interface
    (2) Driver support for indicated device not guaranteed
    Note-1: http://www.broadcom.com/support/ethernet_nic/.
    Note-2: http://opensolaris.org/os/community/laptop/wireless/wpi.

  • No disk found error while install Solaris 8 intel on Compaq

    I use the interactive installation method to install Solaris 8 02/02 intel platform on Compaq DL380 G2 with 4*36.4 GB harddrive and 2G memory. After I configue the network and time, an error message comes up: "No disk found. Check to make sure disks are cabled and powered up."
    When I try the Web Start, it will jump the the shell prompt and say something like "No location for installation software ...."
    Could anyone give me some clue? Thanks.

    Dir Mr. zhechang,
    We had the same error with you, but we install Solaris 9 on the DL380 G3 Compaq machine. Could you please help me to solve the errors if uou the solution about it
    Thanks and best regards,
    Nhut Pham

  • Solaris10 Update 10 (08/11)  No Disks Found error vm3.0.1

    I have successfully installed Sol11 Exprress and Oracle Linux 6.1 in VM 3.0.1 using ISO method.
    My setup includes iSCSI devices and a HA config.
    However, everything I’ve tried with the newly released Solaris 10 R10 (08/11) it fails to finish installing with a No hard disks found error and the install aborts.
    I’ve tried Xen HVM and HVM PV Drives Domain types with same results.
    Has anybody been able to install this release of Solaris in OracleVM 3.0.1?
    Edited by: user10052240 on 22-Sep-2011 9:47 PM

    Still no luck, I get through the installation until it asks about CDROM media, then I get a pop up window with the "No Disks found" eror, after that the install exists to xterm window.
    Here's my vm.cfg in this instance I did not change xvd to hd as all my attempts to change this cause vm not to boot.
    -thanks for any advise.
    memory = 2048
    disk = ['file:/OVS/Repositories/0004fb0000030000914c5da5cda46bfc/ISOs/0004fb0000150000cb99f253bbdcfffc.iso,xvda:cdrom,r', 'phy:/dev/mapper/3600144f0e863c90000004e7d4b5f0002,xvdb,w!', 'file:/OVS/Repositories/0004fb0000030000914c5da5cda46bfc/VirtualDisks/0004fb000012000049d780014c3c21d4.img,xvdc,w!']
    vif = ['mac=00:21:f6:00:00:04,bridge=192.168.0.0']
    usbdevice = 'tablet'
    on_crash = 'restart'
    OVM_description = ''
    name = '0004fb000006000092cffa6918b35871'
    builder = 'hvm'
    on_poweroff = 'destroy'
    boot = 'dc'
    uuid = '0004fb00-0006-0000-92cf-fa6918b35871'
    vfb = ['type=vnc,vncunused=1,vnclisten=127.0.0.1']
    on_reboot = 'restart'
    vcpus = 2
    cpu_weight = 27500
    OVM_os_type = 'Oracle Solaris 10'
    cpu_cap = 0
    OVM_high_availability = True
    maxmem = 2048
    OVM_simple_name = 'sol10r10'
    guest_os_type = 'default'

  • V440 No Disks Found Error

    Hey all,
    I have 2 v440 with 2 disks in slot 0 & 1(in each node). I'm attempting to install S10u8, but I'm getting an error saying, "No Disks Found" during the initial install.
    On the 1st node I was able to install it on one system, but it only saw c1t1d0 and does not see c0t0d0. I've done devfsadm and no go. I have the latest patches installed as well as the latest OBP and firmware/patch installed.
    Also, the system does have the latest firmware-version for the v440 issues.
    prtconf -vp | grep 'firmware-version:'
    firmware-version: '1.03.11.01'
    The 2nd node is the one that is giving me the "No Disks Found" error.
    Has anyone experienced this before?

    Hello,
    On the 1st node I was able to install it on one system, but it only saw c1t1d0 and does not see c0t0d0.
    Is this a typo (c0 and c1, should read c0t0d0 and c0t1d0) ? If yes, reseat the disks (as Martin already suggested).
    Otherwise do you expect to see some of the internal disks on one controller and the remaining on the other ?
    After reviewing the "Matrix of Recognized Device Paths"-InfoDoc, the SCSI backplane is attached to one channel of the SCSI controller. The second channel is the external connector on the back.
    *Please post the output of probe-scsi-all or at least confirm that the disks are displayed at the ok-prompt.*
    Alterrnatively review the disk status via ALOM, this allows to get the information even on production systems without bringing them down.
    Michael
    Edited by: MAAL on 21.11.2009 11:03
    Removed irelevant contents. The OP hesitated to post the requested additional information.

  • Solution for Power Saver error during install

    Hello,
    i have read several topics about the powersaver error during install of this utilty.
    i had the same problem even with a clean install of windows XP and i have found the solution.
    The error seems to disapear and Powersaver works fine after install of the Hotkey utility :
    http://support.toshiba-tro.de/tools/Satellite/sa60/win-xp/hotkey-dd/hotkey-dd-xp-10008sa-du.zip
    Hope this post where helpfull.
    Greetz DeLorean
    [Edited by: admin]

    Hi
    You are absolutely right. Common modules is a kind of basic application who must be installed first. All other Toshiba tools should be installed after. The functionality of Power saver utility depends also on installed common modules.
    Unfortunately I can not give you any kind of advice but in case that there is some error message the best solution is to remove and install the Power saver again. Check also Toshiba download page. Maybe you can find a newer version.
    Bye

  • Quicktime errors during install, uninstall, or run

    Quicktime errors during install, uninstall, or run. No error code. It just says it encountered an error and must exit.

    I located a previous response that satisfied my issue. Below is the process that allowed me to use quicktime.
    The "fatal error" in this context has (recently) been indicating trouble with old, misplaced QuickTime componentry lurking about in your system.
    (Whether or not the message is a symptom of that problem seems to depend on what version of old misplaced stuff is lurking and what version of QuickTime proper we're trying to install or uninstall ... but in recent times, there's been an uptick in fatal errors being caused by that.)
    So let's try investigating that possibility first.
    First we'll adjust some view settings on the PC.
    1. Open My Computer from the desktop or Start menu.
    2. In the Tools menu, click Folder Options.
    3. Click the View tab.
    4. In the "Advanced settings" pane under "Hidden files and folders" make sure that the "Show hidden files and folders" option is selected, and the "Hide extensions for known file types" option is unchecked.
    5. Click OK.
    Now in "My Computer" open Local Disk C: (or whichever drive your operating system is installed on).
    Open the "Windows" folder.
    Open the "System32" folder.
    What files or folders can you see in there with QuickTime in the file or folder name? (In a standard installation of QuickTime, you should see precisely two files ... QuickTime.qts and QuickTimeVR.qtx ... and no QuickTime folders whatsoever.)

  • Errors During Instalation Of Final Cut Studio 5.1

    Aloha,
    I am having some trouble here!! I am trying to install FCP Studio Pro 5.1 on my mac. I tried to do an upgrade from FCP 4.5 HD on my orriginal Hard drive. The instalation went through its paces & asked me to put in the second disc. I did then it came back with an anoucment that there were errors during instalation & to try again I did & was never able to get it to instal... Getting frustrated I ran diskworior on the drive & tried again no luck... after some time I thought it might be the drive would not let me because there was an earlier version on there.... so any way after some other problems with this drive I decided to completely erase & instal Mac OSX on my second hard drive that has never had anything on it. I made this my new startup disk & upgraded the OS to OS 10.4.9 I then Tried to install FCP Studio Pro 5.1 on this drive.. this time It never got to ask me to put in another disk it came back with the same error during instalation try again!!!!!! So now I am getting ******!! but odly enough Final cut studio shows up in my aplications. When I click on it it gives me a warning that there was an error registering & once I click ok it seems to launch FCP 5.1....... ?? So is it really there or not??? & why is it not installing the other 4 discs??? and to add insult to this I have tried to install iLife 06 & I get the same error!!!! WHY!!!!!!!!!
    Another thing.. I installed FCP Studio Pro 5.1 on another Identical computer down the street & it installed no problem!!!!
    Can anyone help Please!!!!!!

    I would take a different approach.
    I would backup the old drive files to an external, and then do a clean wipe and new install of OS, updates and the FCS.
    Best way to do it, in my view.

  • FCP error during install.

    I keep getting an error after installing FCP 5.1.1.
    It says error during install please try again.
    Im using 10.4.7 on my ibook 1ghz 640mb ram.
    I know it will work because a friend has installed it on his.
    Any one help?

    This most often caused by a damaged or otherwise faulty disk in the package. It happens. Try cleaning the disks and then get out your receipt and serial number because your only recourse will be to call Apple for a replacement.
    bogiesan

  • WRT160N error during install

    I just purchased WRT160N and during the install of LELA there is an error. " Linksys Updater failed to start- verify you have sufficient privileges to start system services" pops up during install.  Then it asks to retry and it hasn't worked or close window.  Then when says this "Setup for Linksys Advisor has failed "Fatal Error During Install" please check your settings and try again.
    Help!  I am not computer savy, and don't want to start changing anything and screw it up.
    Internet is working on the installed computer (I believe this is called the gateway? not wireless uses the ethernet cable)but I can't setup my wife's new laptop til this is fixed.
    BTW this is a cable modem hook up if that makes a difference.  I have tried restarting, turning power off as well but still get the same problem every time.
    Thanks,
    Don

    As you have mentioned that your Hardwired computer is able to go online throught the router, and now you are trying to setup your wireless computer. You dont have to run the setup disk on your computer, you can configure all the settings on your Router manually and then make your Wife's computer go online wirelessly..
    Open an Internet Explorer browser page on your wired computer(desktop).In the address bar type - 192.168.1.1 and press Enter...Leave username blank & in password use admin in lower case...
    For Wireless Settings, please do the following : -
    Click on the Wireless tab
    - Here select manual configuration...Wireless Network mode should be mixed...
    - Provide a unique name in the Wireless Network Name (SSID) box in order to differentiate your network from your neighbours network...
    - Set the Radio Band to Standard-20MHz and change the Standard channel to 11-2.462GHz...Wireless SSID broadcast should be Enabled and then click on Save Settings...
    Please make a note of Wireless Network Name (SSID) as this is the Network Identifier...
    For Wireless Security : -
    Click on the Sub tab under Wireless > Wireless Security...
    Change the Wireless security mode to WEP, Encryption should be 64 bit.Leave the passphrase blank, don't type in anything...Under WEP Key 1 type in any 10 numbers please(numbers only and no letters eg: your 10 digit phone number) and click on save settings...
    Please make a note of WEP Key 1 as this is the Security Key for the Wireless Network...
    Click on Advanced Wireless Settings
    Change the Beacon Interval to 75 >>Change the Fragmentation Threshold to 2304, Change the RTS Threshold to 2304 >>Click on "Save Settings"...
    Now see if you can locate your Wireless Network and attempt to connect...

  • Integrity constraint error during install

    We have installed htmldb on zlinux from the companion CD.
    Because we had an error during install of the flows schema we repeat it (have removed the Flows-User and Flow-Files before) using ins.sql! The apache was still running.
    Most of the new installation was fine but near the end we got:
    error creating "Procedure arguments" id=122 Ora-01400, cannot insert NULL into ("FLOWS_010500,"WWv_Flows_STEPS","SECURITY_GROUP_ID")
    declare
    Error at line1
    Ora-02291- integrity constraint(FLOWS_0150000.WWV_FLOW_PLUG_ZO_PAGE_FK) violated
    parent key not found
    ORA-06512 at "FLOWS_01500.WWV_FLOW_API line 4695
    ...

    OK, it's solved:
    I finally managed to install Apex 3.0 correctly once I figured out my error.
    I was logging in remotely to the server the dadbase was on, then trying to connect to sqlplus using 'sys/password@instance as sysdba' to run the script.
    Turns out that the problem had something to do with sys not being allowed to be sysdba when I log in remotely, or that having the username/password and instance info in there made the program think I was logging in remotely and therefore not giving me sysdba privileges.
    The root of the problem was running the install .sql without the correct privileges.
    Since I found out the database server I was trying to install on uses OS authentication, I remote-connected to the database server as the oracle user, tried to run the install .sql again after connecting to sqlplus: 'conn / as sysdba'
    and everything worked like a charm!
    ~PF :)

  • Error During INSTALL of Application Export File

    An error is reported during INSTALL of an application that I am trying to copy (Import/Install) from a "development" Work Space into a "production" Work Space. The production (target) Work Space is on the same HTML DB instance as the development Work Space.
    I am receiving the following INSTALL error:
    ORA-20001: GET_BLOCK Error. ORA-20001: GET_STMT error. ORA-20001: Execution of the statement was unsuccessful. ORA-06550: line 15, column 1: PLS-00103: Encountered the symbol ",'39','RD8','8','S','10','U','43','UD','41','UG','11','W')) END)" when expecting one of the following: . ( * @ % & = - + ; < / > at in is mod remainder not rem <an exponent (**)> <> or != or ~= >= <=
    Following is some pertinent (hopefully) information:
    The above INSTALL error takes exception to part of a Region Select (sql) that works fine in the development Work Space.
    The common HTML DB (v1.6) instance is on UNIX.
    A new Work Space was created on the same instance.
    A new schema name was created during creation of the new Work Space. However, this schema does not point to a database. (We were not certain how to setup the schema to parse to our live database.) I will be running DBLINK upon production application startup in order to access the database objects.
    EXPORT INFO -
    File Format: UNIX (also, tried DOS but received same error during INSTALL)
    IMPORT INFO -
    File Type: Application/Page Export
    File Character Set: Western European Windows 1252
    Target Work Space is newly created on the same HTML DB instance.
    INSTALL INFO -
    *Parse As Schema: COLLIVE17 (Again, this schema does not parse to a database. I intend to use DBLINK.)
    *Build Status: Run and Build Application
    Please refer to above error message.
    Again, any insights or suggestions are appreciated.

    Urgently need help! I've read several other Forum messages having a related problem but none having same Install error message.
    Again, my Export/Import from development Workspace to production Workspace is successful. The following error is reported when I attempt to "Install" into the production Workspace:
    ORA-20001: GET_BLOCK Error. ORA-20001: GET_STMT error. ORA-20001: Execution of the statement was unsuccessful. ORA-06550: line 15, column 1: PLS-00103: Encountered the symbol ",'39','RD8','8','S','10','U','43','UD','41','UG','11','W')) END)" when expecting one of the following: . ( * @ % & = - + ; < / > at in is mod remainder not rem <an exponent (**)> <> or != or ~= >= <=
    The "snippet" of Region Sql Select code that relates to the reported error is:
    ELSE htmldb_item.display_and_save (5, DECODE (GET_GRADE_B93 (sac.stc_final_grade,sac.stc_verified_grade),'18','AU','1','A','3','B','4','C','7','CR','5','D','46','DR','6','F','47','FW','49','IB','30','IC','31','ID','23','IF','44','MW','9','NC','21','RD','14','RD0','33','RD1','32','RD2','34','RD3','35','RD4','36','RD5','37','RD6','38','RD7','39','RD8','8','S','10','U','43','UD','41','UG','11','W'),'GRADE_'||ROWNUM) END q_v_grade,
    HTML DB version is: 1.6.0.00.67. I've also tried to Export/Import/Install the application into the "same" Workspace specifying the same schema, and only changing the Application ID. However, I get the same Install error (see above).
    Any suggestions on things to try in order to get application into production is greatly appreciated.
    Thanks, Bernard.

  • BUG 2.1 - ARW (Sony Raw) no photos found error during Auto Import

    BUG 2.1 - ARW (Sony Raw) no photos found error during Auto Import
    I've seen this issue since beta1. The issue seems to be related to a camera setting that stores the files in folders by date. The Folder structure becomes drive>DCMI>10202008>image.ARW
    This "no photos found error" I have seen in beta1 LR1 LR1.1 LR1.2 LR1.3 LR1.4 and LR2.0 this is still an issue in LR2.1
    Auto import works fine with canon or nikon RAW files (I've used several different cameras with no problems)
    The Folder structure for canon files is drive>DCMI>100>image.CR2
    Auto import Does not work with Sony A100 .ARW files with folders by date turned on I have heard from people with other Sony cameras like the A700 also have this issue.
    Vista Ultimate 32bit SP1
    AMD 64X2 duel core 6000+ 3Ghz
    6GB 666mhz Ram PAE force enabled
    NVIDIA Gforce 7600 256MB video card (1.75GB total with system shared ram)
    Primary hard drive: 500GB
    Hard drive 2: 400GB (system and photoshop paging files and lightroom catalog drive)
    Hdrive 3: 1TB (primary image storage)
    user control turned off
    system graphics set to performance
    Duel display
    Lightroom 2.1
    photoshop CS3

    I believe this is fixed in version 2.5 and 3.0
    ARW (Sony Raw) files seem to work with auto import

  • OMS error during install Grid control 10gR2 on Windows 2003

    He,
    I get this error during install Grid control 10gR2 on a new server win2003.
    "oracle.sysman.emcp.agent.AgentPlugIn"
    What I see in forums is that I have to stop my listener and continue my installation.
    But I still have the same error !!
    Can you please help?
    Many thanks

    There are some guidelines here:
    Subject:      OracleAS Install Error When Configuring AS Console Agent - "oracle.sysman.emcp.agent.AgentPlugIn has failed"
         Doc ID:      Note:386308.1
    The solution stated is "Check the contents of the hosts of file and ensure that every entry is correct. All hostname / ip addresses have to be valid."
    When installing AS 9i R2 there was an issue with the names, those were supposed not to hava a hypen, so may be something was inherited from those kernels.
    There is another metalink note that document hosts issues:
    Problem: AgentCA: Grid Control Release 2 install fails with java.lang.Exception: 6 during Agent Configuration Assistant
         Doc ID:      Note:358640.1
    ~ Madrid.

  • FILE NOT FOUND ERROR WHILE INSTALLING ORACLE EM GRID CONTROL 10.2.0.1

    FILE NOT FOUND ERROR ON FILES: generalstup, seedstup during the setup phase and when i click ignore from a list of cancel, retry and ignore it moves to the configuration phase and rapidly moves from 63% to 100% and gives the error OUI-10133 invalid staging area. i have tried the install 3 times and dont know what the problem is. i am doing the oracle EM GC INSTALL WITH NEW DATABASE OPTION. i downloaded the full version disks 1-3 from the website:http://www.oracle.com/technology/software/products/oem/index.html
    Enterprise Manager 10g Grid Control Release 2 (v10.2.x)
    Full Installers (Agent, Repository, OMS, and Management Packs)
    Oracle Enterprise Manager 10g Grid Control Release 2 (10.2.0.1) for Linux x86
    when this is extracted it leaves me with Disk1, 2, and 3
    install started from 1, then it later asks for two whick happens to instead be but under Dist 3-but there are two disk2's under Disk 3- one under oms and one under rdbms folder. i have tried both and alas same errors
    i even triwd the same download from edelivery.oracle.com and gives the same madness
    am stuck.

    i followed the link and all the instructions things seemed to go well: it still asked for two files i did not have or could not locate: first its asked for generalstub, then it asked for seedstup and then generalstup again. at this point the installation was at 67% and had passed the link succesful stage and was at the setup succeful stage. when i clicked ignore on generalstub, seedstup and then generalstup again it quicly moved to 100% and never took me to the stage for me to run oraInstroot.sh and allroot.sh
    the configuration assistant stage never cameup and it skipped to the page Specify Repository Database Configuration
    where it asked for repository database hostname port, service/sid and SYSMAN password and also manament service security password. whe i input all the infor mation it will give errors. i have tries deleting all oracle 3 or 4 times and all files that oracle has and repeated the process and am always stuck here.
    error reads :
    -error cheching the existence of the SYSMAN user in Management repository
    -exception occured while connecting to database . please check the connection details you specified and retry
    -io exception connection refused: (DESCRIPTION=(TMP=)(VSNUMM=168821760)(ERR=12514)(ERRO_STACK=(ERROR=(CODE=12514)(EMFI=4))))
    REP DB HOSTNAME:SA-OMS-01
    PORT:1521
    SERVICE/SID:OMSDB01
    SYSMAN PASSWORD:PASS
    THE REST I PUT PASS AS PASSWORD
    NOT SURE WHAT TO DO NEXT.

Maybe you are looking for