NO DISPLAY, TWO TIMES CAPS LOCK BLINKING

I HAVE A HP PAVILION DV6 -7023TX IT IS NO DISPLAY AND CAPS LOCK BLINKING TWO TIMSE I DNT HAVE WARRANTY ALSO PLASE HELP ME !!!!!!!!!!!!! GIVE ME A good solution ..........
zaid

Caps Lock/Num Lock LED
Component Tested
Error Condition
LEDs blink 1 time
CPU
CPU not functional
LEDs blink 2 times
BIOS
BIOS corruption failure
LEDs blink 3 times
Memory
Module error not functional
LEDs blink 4 times
Graphics
Graphics controller not functional
LEDs blink 5 times
System board
General system board failure
LEDs blink 6 times
BIOS
BIOS authentication failure
****Click the White Kudos star to say thanks****
****Please mark Accept As Solution if it solves your problem****

Similar Messages

  • Caps lock blink 5 times on Compaq 615 laptop, but screen doesn't come on.

    My Compaq 615 laptop screen doesn't come on, instead it blinks capslock 5 times. What shlould I do?
    It has an AMD Athlon X2 processor, with Radeon 3200 graphics.
    I didn't install any new software or hardware recently. All I did was work with the system at night, shut it down, and when I turned it on the following morning, the screen refused to come up, but the caps lock blinks 5 times.

    Sorry to hear that. Please refer to the Blank Screen LED Error Codes document from HP Support. It sounds like a "General system board failure." The explanation says to contact HP for assistance. The motherboard might need to be replaced, and you will probably require the assistance of a technician to fix the problem. 
    Please click the thumbs up button to say "Thanks!"
    Clicking "Accept as Solution" on a reply that solves your problem makes it easier for other people to find solutions.
    I am an HP employee.

  • Hp Probook 4510s caps lock blinking no screen display

    I rebooted my laptop and all the lights come on but network light ends to turn orange and caps lock blinking.

    Well, my RAM will arrive tomorrow, we'll see if it works or not. Surprisingly, the laptop charges like it should, everything is fine except the 3 blinks. 
    I hope the new RAM will solve the problem.

  • Hp pavilion g4 1104dx display white screen and caps lock blink twice

    Hi i recently used my hp laptop screen to test another laptop acer aspire 5517. After the test i reconnected back the cable only to power it on a white screen appeared with caps lock blink twice. I thought the problem might be screen shot so i decided to connect to external monitor but still no signal on external monitor even after pressing fn+f4. What might be the problem thanks.

    Hi there , Thank you for visiting the HP Support Forums and Welcome! This is a great site to get answers and ask questions. I understand you are having an issue with your Notebook. You had stated that you receive a White Screen and the Caps Lock are blinking twice. Please be very careful when it comes to blink patterns as sometimes there can be a pause between the blinking.   Before you start troubleshooting, please note remove any and all USB devices. Disconnect all non-essential devices, as these could cause some issues. Here is the first document I found called Performing a Hard Reset or Forced Reset. If that does not work, please follow Computer Does Not Start (Windows 8). The last document I have for you that may help is called Computer does not start and the LEDs blink or the computer beeps. Please follow these provided troubleshooting steps, re-post and let me know how everything went. Thank you! Have a great day!

  • Pavilion DV6, Black Screen and 3 Caps Lock Blink

    HI,
    I have an Hp Pavilion DV6 and I am getting the 3 blinks on the caps lock. When I turn on the PC it starts up, the caps lock blinks 3 times and the screen is just black. I have already tested the memory sticks, drain the battery, and hooking it up to an external monitor.  Nothing shows on the other monitor and it just remains black. Please help!

    Hi @shmurray,
    Welcome to the HP Support Forums!
    I understand you are getting a blink pattern on the Caps lock LED, when you turn on the notebook. I am happy to help you with this.
    I am including the page on the error codes for your reference: Blank Screen LED Error Codes
    From that document the pattern you are getting indicates a memory problem. You said that you have tested the memory. What exactly did you try?
    The document suggests reseating the RAM or trying a new set of RAM and then restarting the notebook. If you are still getting a memory problem after trying both of those things, ie a 3 blink code again, then it would likely suggest that there is a problem with the motherboard itself, either with the memory slot or one of the controllers related to memory.
    In that case I would suggest contacting the technical phone support number at 800-474-6836. If you live outside the US/Canada Region, please click the link below to get the support number for your region.
    http://www8.hp.com/us/en/contact-hp/ww-phone-assist.html
    If however reseating the memory or replacing it leads to a different error code or message please let me know, Although in that case the following may be helpful if you still have a blank screen.
    Troubleshooting Black Screen Displays with No Error Messages During Startup or Boot
    Here are some other sources I found that may be helpful to you.
    Resolving Problems with Notebook Displays (Windows 7 and Windows 8)
    I hope that this is helpful to you.
    Regards,
    Malygris1
    I work on behalf of HP
    Please click Accept as Solution if you feel my post solved your issue, it will help others find the solution.
    Click Kudos Thumbs Up on the right to say “Thanks” for helping!

  • Black screen with caps lock blinking

    I was using my laptop and it was turned on and after some other work I wanted to use my laptop, the screen was black and caps lock was blinkingI turned it off manualy and it was again doing this. Caps Lock blinks 2 times after a pause of 4 seconds continously.
    I tried reset and other things but its not showing anything. 

    Hi Nayj424,
    Thank you for visiting the HP Support Forums and Welcome. I have read your thread on your Compaq Presario CQ62-102TX Notebook and getting a blank or black screen on startup. Try performing a hard reset. When performing a hard reset please note remove any and all USB devices, and remove memory cards from the card reader slot. Disconnect all non-essential devices. If that does not help try to turn on the computer you start to press F11 repeatedly till the menu opens. You can do a system restore.
    Hope this is helpful.
    Thanks.
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos, Thumbs Up" on the bottom to say “Thanks” for helping!

  • Blank Screen; Caps lock Blink Twice Every 2/3 Seconds with orange wireless button.

    Hi,
    I am using my HP Pavilion DV6 7023tx laptop. It is 1 year 3 months older(warrenty expired). It was working fine but one evening i found it start with black screen and caps lock blink twich every 2/3 seconds and after some times it's getting hot.
    I have tried to solve the issue accoroding to the following link
    http://h10025.www1.hp.com/ewfrf/wc/document?cc=us&lc=en&dlc=en&docname=c01732674
    It looks like BIOS corruption failure. but it will not automatically recovering that mentioned in post.
    So what should i do now?
    Could you guys tell me what should i do?
    Thanks in advance.
    Product Information:
    ===============
    HP Pavilion DV6 7023tx
    Serial No : 2CE22927FG
    Product ID: B3J66PA
    This question was solved.
    View Solution.

    Hello SuperMario1,
    Thanks for your response.
    The last thing i did, remove CMOS battery and after a few minutes i plugged it.
    Then connect AC power adapter and press power button.
    Laptop starts but gives a error message
    "The CMOS checksum is invalid, The BIOS will be reset to the default configuration and will be rebooted."
    Finally laptop start normally. It works fine ...
    But same problem when i restart
    "blank screen caps lock blink 2 times every 3/4 sec"
    So finally
    1. remove CMOS battery and after a few minutes i plugged it again
    2. connect AC power adapter and press power button
    3. laptops starts normally (with a error msg same as previous)
    4. Upgrade bios to F.29(previously i had F.24)
    5. Everythings works fine (restart/shutdown have no effect)
    Nirupam Chandra Modak

  • Caps lock blinks twice

     I own HP Pavilion dv6 Notebook PC.  I havе the problem when starting my laptop. It works fine when it is on but when i turn i off and than on it won't start normally. When i push the start button, the laptop doesn't start fully. The fan works but the screen stays black. Also the CAPS LOCK blinks twice and the wifi and mute buttons stay orange. 
     I tried pushing windows buttоn+B button + power button, i updated BIOS. And nothing works. It still gives the same problem.
     Could you give me some advice.
    Thank you.

    Hello @M_O_P, 
    Welcome to the HP support forums.  Your blinking feature is unfortunate.  Thank you for providing
    your model number of your notebook.  Could you post back the Product number of your notebook as well.  Use this link to help find this information.
    How Do I Find My Model Number or Product Number?
    In the mean time here is a link you can use to determine what problem you are having by the blink code that is showing.
    Computer does not start and the LEDs blink or the computer beeps  
    Once you post back with your Product number I will be able to look a little deeper into the issue for you.
    Oh and one more thing.  Here is a link for Restoring the BIOS on your HP Notebook.
    Restoring the BIOS
    Hope to hear back from you soon.
    Thanks for posting.
    Please click the "Thumbs Up" on the bottom right of this post to say thank you if you appreciate the support I provide!
    Also be sure to mark my post as “Accept as Solution" if you feel my post solved your issue, it will help others who face the same challenge find the same solution.
    D5GR
    I work on behalf of HP

  • My HP G56 Wont turn on (Caps Lock Blink)

    Heyy guys
    so i turned on my HP G56 Laptop this morning and nothing happens but the caps lock blinking and the wifi and power lights are red. i found online some codes but the caps lock codes when upto six, my laptops caps lock keeps on blinking and doesnt stop. it blinks around every 4 seconds.
    HELP????

    Hi sahibsahib,
    Welcome to the HP Support Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More.
    I see that you are having some problems with your laptop. That blinking light does indicate a hardware problem. It should be blinking in some sort of pattern and it will repeat. If just keeps blinking every four seconds then it could be just one blink which would indicate a CPU failure. This HP support document on Computer Does Not Start and the LEDs Blink will show you the various blink codes.
    If you have purchased the laptop within the last year you are in warranty and I would recommend that you contact HP. You can reach HP Total Care at 1-800-474-6836 in North America or start here if you live outside of North America. If you are out of warranty you can still contact HP but there would be a charge or you can take it to a local technician.
    Thank you,
    Please click “Accept as Solution ” if you feel my post solved your issue.
    Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
    Thank you,
    BHK6
    I work on behalf of HP

  • HP ProBook 6540b won't boot and caps lock "blinking" continuously.

    Hi,
    I'm trying to help a friend with his laptop a Probook 6540b.
    It won't boot and caps lock "blinking" continuously.
    When I got it caps lock and num lock was "blinking" tre times... indicated memory problems, reseated the memory modules
    and the the "tre time blinking" disappeared, but caps lock now blinking continuously and the only way to shot down the computer
    is to disconnect the power.
    Anyone with some ideas???
    Janson 

    A neighbor had the same problem and asked for my assistance.  I created a rescue disk using my HP desktop running Windows 7 64-bit.  Even though her HP laptop was running Windows 7 32-bit, the disk allowed me to boot into windows on her computer.  I then went to the HP web site and downloaded the latest BIOS and then flashed it to the BIOS chip following the instructions that came with the download.  Everything is working fine now.  Hope this helps.

  • My laptop won't boot and caps lock blinking continuously (1blink in 4 sec.)

    Sir,
    Today morning I turned on laptop but laptop won't boot and wireless button glowing continuously and also caps lock blinking continuously as 1 blink per 4 sec.

    do you mean 1 blink repeating and then a pause and 1 blink repeating again? The diagnostics show that as a CPU not functional issue.http://support.hp.com/us-en/product/HP-Pavilion-15-Notebook-PC-series/6529948/model/6622489/document/c01732674#AbT2   Try a hard reset.Follow the instructions at the following web page.http://support.hp.com/us-en/product/HP-Pavilion-15-n209tx-Notebook-PC-(ENERGY-STAR)/6529948/model/6622489/document/c01684768 If a hard reset does not help, then contact HP for warranty service.  Is your notebook still in warranty?Check your warranty status Here.

  • Pavilion dv6-7010us black screen, caps lock blinking indefinitely and orange wifi light

    The laptop is a HP Pavilion dv6-7010us resently installed windows 8.1 pro, 8gb ddr3 (4gbx2), 320gb hdd (not the original hdd)
    i was giving a normal maintenance to the laptop to remove the dust, nothing of the other world, the machine where functioning pretty well 'till this moment, i turn on the laptop and i see the caps lock blinking at 1sec intervals and the wifi light in orange not blinking just led on when i turn on (NOT NUM LOCK LIGHT ON), and this is it, nothing more, i dont know what to do, i use the WINDOWS KEY + B to reset the BIOS and nothing, i leave the power botton hold for a minute without the battery nor the power source, and plug the cable and turn on again without the battery and nothing, also where testing changing the memory from slots i have 2 memories of 4gb and nothing, anybody can tell me any combination of keys to resolve this that i don't use yet?

    What did the normal maintenance include-any disassembly? I assume the laptop is still under warranty?
    ******Clicking the Thumbs-Up button is a way to say -Thanks!.******
    **Click Accept as Solution on a Reply that solves your issue to help others**

  • Lap top wont start up , caps lock blinking 3 times

    I have an envy 6 sleekbook and all of the sudden it wont start up and the caps lock is blinking three times i have already saw the blinking code and tried resting the memory but it still wont work , i have ran into problems with the laptop before like the blue screen but it was fixed on its own i think

    Dear Customer, Welcome and Thank you for posting your query on HP Support Forum It looks like your Notebook has a blinking/flashing CAPSLOCK light and a blank screen all the time If the Capslock LED is blinking 3 times that means "Memory error not functional", In order to resolve the issue we need to Replace Memory Module Note: If you are comfortable opening the Notebook, you can check how many memory modules you have. If you have two memory modules you can test one at a time on both the slots individually to verify if the fault is with the memory module or the memory module slot of your Notebook [Repeat the same steps for testing another memory module] If you find the above steps difficult and as this is a hardware issue and I recommend you to Contact HP Technical Support over the Phone for further assistance without any delay to get your Notebook diagnosed and serviced by an authorized HP Certified Engineer You can also Check your warranty Here to verify the warranty status Hope this helps, for any further queries reply to the post and feel free to join us again  **Click the KUDOS star on left to say Thanks**Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem. Thank You,GBL84Although I am an HP employee, I am speaking for myself and not for HP

  • Caps Lock blinking 13 times...

    Hi I have a HP 2000-363NR, when I power up the screen stay black and the Wireless led stays on in orange color and the Caps Lock led blinks 13 times. I check the errors codes and only explain to 6 blinks but mine blinks 13 times. I have tried changing the memory and HD and nothing, what else I can try? Thanks in advance...!

    Hello,
    I understand your laptop will not boot.
    You did mention that the caps lock light blinks 13 times, after that happens does the laptop go off or continues to stay on with just a blank screen does anything significant happen?  Reason why I’m asking because 13 isn’t a normal blink code, now it could be just considered one continuous blink which is normally means the CPU isn’t functional.
    Also do you ever see the HP logo screen or starting windows does anything like that appear?
    Please respond back when you can.
    Thanks
     

  • Blanc screen at startup / Caps lock blinking 3 times HP Pavilion dv7

    Hello,
    Hope someone can help me out.
    First we received SMART warnings but we were still able to start up Windows in safe mode (took about 15 minutes and the laptop was getting warm). We took the HDD out and connected it via USB to an other PC. We could not read the content and needed to format the disk... did NOT do that. We kept the HDD "origional".
    We bought an Samsung EVO 850 250 Gb SSD for the laptop... as replacement for the corrupted one and to upgrade the system. The main battery was removed, adaptor was not plugged in for a couple of days. Today we received the new SSD and installed it... but... the laptop is not starting up anymore! The screen stays completely blank. The F12 is lighting orange and the CAPS LOCK is blinking 3 times. 
    We've read several articles on forums and tried various suggestions:
    - Changed the BIOS battery;
    - Several "hard resets":
      . removing adaptor and main battery and pushed the power button for 15 seconds;
      . Windows, B and power button at startup;
      . pressing F8 while booting;
    - build the original HDD back in;
    - removed the memory and tried all banks in all slots;
    - connected external monitor;
    - startup via bootable USB stick;
    - cleaned the cooler fans (with compressed air spray);
    - tried an other AC adaptor;
    - tried without the main battery;
    - tried to startup with no memory, no BIOS battery and no HDD installed.
    Doesn't matter what we tried... after trying every suggestion the screen stays blank and the CAPS LOCK is still blinking 3 times repeatedly.
    Anyone any idea what ik can try further? In my perception the BIOS is not loading at all?!?!
    Looking forward to read your suggestions! Thanks in advance
    Best regards,
    BerDie13
    This question was solved.
    View Solution.

    Hi there @BerDie13 
    Welcome to the HP Support Forums! It is a great place to find the help you need, both from other users, HP experts and other support personnel.
    I understand that you are getting a repeating pattern of three flashes from the LEDs. I am happy to help with this.
    Check out this page under the section for flashing LEDs. In that you will find that three LED flashes indicates a memory problem.
    Computer does not start and the LEDs blink or the computer beeps
    Use the instructions on how to deal with that. I am a bit concerned that you have both a hard drive failure and a memory issue, but it is possible that the memory could have been disturbed when you were working with the hard drive. If the reseating of the memory does not help, I would try the memory in different slots and if you have more than one memory module try them one at a time in both slots to isolate which is the problem child. The worst case would be multiple bad memory modules and a defective set of sockets on the board.
    Let me know what you find.
    Malygris1
    I work on behalf of HP
    Please click Accept as Solution if you feel my post solved your issue, it will help others find the solution.
    Click Kudos Thumbs Up on the right to say “Thanks” for helping!

Maybe you are looking for

  • GD causing program to die with threading

    I've been working on a fractal generator for the past few days and decided to add multithreading support tonight-just one problem, this code works perfectly without threads, and not all with threads: Works: thread_options_t *toptions = (thread_option

  • Can you put back the letter index to make selection of the files easy?

    I have well over 1000 pdf papers and it is tedious to scroll the list to find the right file to open.  The old versions had a column on the right with letters which act as an index, but with the recent upgrade or downgrade, that has somehow disappear

  • XI in a SOA landscape  - licensing

    We are in the process of formulating a SOA strategy. We want our webservices platform to be on .NET and since SAP doesn't have webservices management tool we are also evaluating Amberpoint/Actional. SAP has not clearly spelt out how licensing will wo

  • "Locking" layers view in InDesign

    I'm not even sure how to describe this, so forgive me if there's something out there than answers this question. I work with layers in both photoshop and illustrator quite a bit, mainly because I work with things that have displays and those displays

  • Imovie hang up on start

    I recently uprgraded to maverick (big mistake) and now two externatl hard drives aren't recognized.  Today I tried to open imovie and the computer hung up. This is the second hangup I've had since installing Maverick.  I never had any hangup in the t