No gateway replay N82

Hi to every one,
Problem I have is can't connect to internet!!!!
I can connect to AP but can't go further. I get the message no gateway replay.
I tried to enter the IP address and Gateway still no results then I installed the WLAN application to help me connect still no luck.
If some one can help me on this issue I will appreciate a lot.

Where are you trying to connect? Public access points(eatery, hotels, airport) or your private home WIFI set-up? If it is the latter check if mac address filtering is enabled & put the mac address or your phone. That message means your not able to connect to a DNS.
Message Edited by android on 16-Mar-2008 09:11 AM
Knowledge not shared is knowledge wasted!
If you find it helpfull, it's not hard to click the STAR..

Similar Messages

E71 WLAN problem "no gateway replay"

Hallo nokia
E71 wlan not working...."no gateway replay"
why Nokia care do not find any sloution about this problem because many e71 holder have the problem around the world.
i have called to noika. de cannot help about it. no update for e71.
have anybody solution. please help us
E71 OWNER

this type of error message comes only when the router is not allowing the handset to access it. when the authentication fails the router rejects the request and we get the error message as "no gateway reply"
to solve this try the following
check whether the sim card is properly inserted and the handset is not in offline mode.
enable "show wlan availabilty" from wlan setting.
disable automatic configuration.
reset the WLAN access point to default setting and start defining again.
after config the access point manually on your device, go to the web browser setting and select the acccess point as always use.
try selecting another access point.
you can do the access point setting from options> advanced settings.
if my post helped u out, please click the Star next to it to add some KUDOS to my name
Thanks and Regards,
Sherry.

E66 no gateway replay with public wlan

My problem is whenever I try to open the Web from public wlan in my university and everywhere, a message appears "no gateway replay" my mobile is the Nokia E66
help me please ....

Have a look at the link below and see if any of the suggestions help.
/t5/Pool-of-Knowledge/No-Gateway-Reply-when-connecting-to-Wlan/td-p/578287

Troubles with WLAN on N95 8gb!!!

I have a problem with wirless , sometimes when i want to start the WLAN it shows the message:
Web:NO gateway replay!!!
I want to change my software to the newest version? will it solve my problem with the WLAN?
Thanks 4 the Help
p.s.Do I have to wait , when iam conneting to the wirless network, or it should start browsing imiditally?

When you use the browser it will look for the default access point that you configured be it wireless, 3g ect.
Knowledge not shared is knowledge wasted!
If you find it helpfull, it's not hard to click the STAR..

While talking on the phone i can hardly hear what ...

its going to be 2 months since i bought my nokia E66, i like the phone but two things bother me most.
the first one is that the call volume is so low that i can hardly hear what the other party says
the other one like most of falks here "No gateway replay " when i try to connect to open WLAN. i have tried to disable the "automatic configuration" and "power saving" but there is still the problem. i was thinking, if i disable the automatic configuration, does that mean that i have to statically assign IP address to my E66?
i would be so happy if someone helps me.
thanks

Tried turning up the call volume (you do that while in a call either with the joystick right or volume up key)?

Oracle XML Gateway Message Designer for Oracle EBS R12.1.2

Goog Day to everyone!
I'm Looking for the tool "XML Gateway Message Designer". I have found in Metalink(Oracle Support) the note ID 557101.1, here explain how to get the message designer for Oracle Apps R12. It says that you have to download the patch 4066964. This patch install the Oracle Workflow Builder (2.6.3.0.1) and the Oracle XML Gateway Message Designer (2.6.3). This tools are supported to be used with Oracle Apps 11.5.10 and 12.0.X.
The release of Oracle Apps that I'm using is 12.1.2.
Questions:
- The version of the Message Designer that you get from patch 4066964 works for OraApps R12.1.2 ?
- The version of the Workflow Builder that you get from patch 4066964 works for OraApps R12.1.2 ?
- If the version of Message Designer doesn't work with OraApps R12.1.2, where can I find one that works with it?
Thanks for your advice.
LCJ

Hi Hussein,
Thanks for replay.
I downloaded the rapid install package from e-delivery. The B53824-01_4of4 was the OWB installer, and it has a readme file that says: "+This patch contains Oracle Workflow Builder (version 2.6.3.0.1) and Oracle XML Gateway Message Designer (version 2.6.3). These client tools are supported for use with an Oracle E-Business Suite Release 12.1 instance.+"
I believe, as well as you, that it should be work for 12.1.2.
I'm gonna make some test, and in a few days I will post my results.
Thanks for the help.
LCJ

Nexus 5500 duplicate ICMP echo-replay

I am experiencing inconsistent echo-replay from devices connected via VPC to Nexus 5500s while pinging from the Nexus exec prompt.
In some cases I receive normal response when pinging from one Nexus, but no response when pinging from the other switch. In other instance I receive normal response to one Nexus, and duplicate replays to the other. It looks like a VPC related bug. NXOS is 5.1.3.N2.1
5501# ping 10.12.12.232
PING 10.12.12.232 (10.12.12.232): 56 data bytes
64 bytes from 10.12.12.232: icmp_seq=0 ttl=253 time=8.585 ms
64 bytes from 10.12.12.232: icmp_seq=0 ttl=254 time=9.227 ms (DUP!)
64 bytes from 10.12.12.232: icmp_seq=1 ttl=253 time=1.011 ms
64 bytes from 10.12.12.232: icmp_seq=2 ttl=253 time=8.097 ms
64 bytes from 10.12.12.232: icmp_seq=2 ttl=254 time=9.429 ms (DUP!)
64 bytes from 10.12.12.232: icmp_seq=3 ttl=253 time=18.195 ms
64 bytes from 10.12.12.232: icmp_seq=4 ttl=253 time=8.807 ms
5502# ping 10.12.12.232
PING 10.12.12.232 (10.12.12.232): 56 data bytes
64 bytes from 10.12.12.232: icmp_seq=0 ttl=254 time=0.985 ms
64 bytes from 10.12.12.232: icmp_seq=1 ttl=254 time=0.884 ms
64 bytes from 10.12.12.232: icmp_seq=2 ttl=254 time=0.875 ms
64 bytes from 10.12.12.232: icmp_seq=3 ttl=254 time=3.105 ms
64 bytes from 10.12.12.232: icmp_seq=4 ttl=254 time=8.378 ms
Thanks
Jarek

Hi
I found this in the configuration guide for the Nexus 7000 configuring VPCs
"When you enable this feature (peer-gateway), Cisco NX-OS automatically disables IP redirects on all interface VLANs mapped over a vPC VLAN to avoid generation of IP redirect messages for packets switched through the peer gateway router."
However this is not happening automatically on the 5K, so you need to manually add "no ip redirects" on each VPC vlan interface to prevent duplicate pings.

N82 does not correctly process DHCP leases

I have no problem attaching my new N82 to my, and friends, home wireless networks. However, it fails to connect to the Univeristy Campus network giving the error: "Web: No gateway reply!"
This is because the phone doesn't correctly process DHCP leases with the 'network of one'' (2545.255.255.255) subnet mask.
Campus network details:
HP WAP 530 enterprise access point. The DHCP server is an ISC dhcp server giving out ip address in the standard private class C address range (192.168.1.0) with a subnet mask of (255.255.255.255), and a default route of 192.168.1.1.
This works on Windows 2000/XP/Vista and MAC OSX, but many embedded devices will not add the default route as they see it as outside their subnet. Many institutions use 255.255.255.255 to mitigate inter host communication.
This means I cannot use my N82 at work and I'm not happy. Beware, don't assume you can use your Nokia device at work.

If task manager says it's still running, then obviously it hasn't completed, contrary to what you said. Maybe this .exe process isn't written correctly. For example, maybe it is dependent on the current directory it is launched from, and so double-clicking it causes it to be launched from the directory it lives in, but when run from this java app, the working directory is somewhere else.

PLEASE HELP!!!! N96 "no gateway reply" PROBLEM

Hi
I have a N96 v12.
When i try to connect to internet with Wifi i cant browsing and system said that "no gateway reply".
i tried to connect to this connection with N82 and its work well.
Where is the problem from?

I´ve searched other threads on this board and it seems like, you´re not the only one experiencing problems with the N96 and WiFi.
It seems like there is no proper solution for your problem...
Some users have reported that they´ve managed to connect after updating the phone´s firmware!
You can update your phone using the NSU:
Nokia Software Updater
All you need for this is a internet connection and a data cable for your phone!
Is your phone´s firmware up to date?
Your English is good enough to make yourself understood.
By clicking the "Kudos!" or the "Solution?" button on the right you can say "Thank You" and you´ll show the author and others that the post is useful.
The day we stop improving is the day we stop being good.

Oracle EBS XML Gateway inboud senario

Hi folks,
Now I am trying to do Oracle EBS XML Gateway inbound senario using OTA and WID/WPS.
For using OTA, after I send a request from OTA client, then I can see a record inserted into table ecx_inqueue, then this record dispear. I see this request is processed sucessfully in transaction monitor. I can see request data is stored in predefined data table.
But when using WID/WPS to sent a request, I get ResponseCode 200 and also see a record inserted into table WF_WS_JMS_IN, then this record dispear. But from transaction monitor I cannot find this transaction record not matter it is successful or error or warning. I also cannot see the request data in data table.
In table wf_error, there isn't my record.
Is there anyone who can help me figure out how to see whether my request is sucessful or failed? If it is sucessful, I should see it in transaction monitor; if it is failed, I should see it in table wf_error. But now I cannot find it.
Some one who is familar with the whole process, pls help me to understand.
Thanks in advance.

Hi Hussein,
Thanks for replay.
I downloaded the rapid install package from e-delivery. The B53824-01_4of4 was the OWB installer, and it has a readme file that says: "+This patch contains Oracle Workflow Builder (version 2.6.3.0.1) and Oracle XML Gateway Message Designer (version 2.6.3). These client tools are supported for use with an Oracle E-Business Suite Release 12.1 instance.+"
I believe, as well as you, that it should be work for 12.1.2.
I'm gonna make some test, and in a few days I will post my results.
Thanks for the help.
LCJ

N82 Camera Fault Please Help...

Dears:
I recently bought N82 Middle East version, from I2 dealer in Jordan with 2 years guarantee.
I noticed a severe victory fault in the camera.
A huge amount of green and pink noise filled the LCD and appeared in the token films and photos too.
Some times this noise disappear or decrease after a while of using camera.
Now I’m in Syria and I asked I2 dealer to replace my mobile with a new one if it was a hardware fault, because I don’t appreciate the idea of repairing my new device. It wont be new any more.
Is this a software or a hardware issue?
Do you have an advance information about this fault?
I would appreciate a quick replay.
Thank you Very much.
Regards,

Not to sure mate, i thought it could have been app's running in the background.
Grayburn @ www.nokiausers.net & www.dailymobile.se....come say Hello!!!
If you appreciate ANY help from a member,then show it by clicking on the Blue Star button, cheers

Cisco 4000 & 3000 series ip route & ip default gateway

Dear all ;
I have Enterprise Network Contain :
- Foundry Big Iron work on layer 3 , and Combination of 4000 and 3000 and 2000 cisco switches work on layer 2;
management network for the switches is 192.168.100.0
Foundry Big Iron is 192.168.100.1
i use ip default-gateway 192.168.100.1 on all cisco switches.
all other subnets route through the foundry.
but when i ping from any subnet (192.168.15.0) to any 3000 or 2000 switches series it replay and when i ping to 4000 series it don't replay.
when i use default route command on 4000 series it replay.
i need some explanation
Kind Regards

In the original post it describes the Cisco switches as operating as layer 2 switches and I assume that in terms of how they are configured to forward traffic all the Cisco switches including the 4000 are configured only for layer 2 forwarding. But with IP routing enabled (as seems to have been the case on the 4000) the behavior of the switch becomes a bit different. In particular is the difference in how you identify the default route. For a switch that is layer 2 only you use the default-gateway command (which apparently worked fine for the 2000 and 3000 switches). But when you enable IP routing then the switch does not use the default-gateway to learn its default route and would look for some other mechanism to learn its default route. I am assuming that there was not any other mechanism and so the 4000 basically did not have a default route. When you configure no ip routing (which was good advice from Paul) then the 4000 stops working as layer 2 switch and at that point will use default-gateway to determine its default route.
HTH
Rick

Possible N82 WLAN Defect?

Having just got my shiny new N82 I've tried to get it connected to my wireless network. I had some problems getting it to see the access point.
It seems that although I've specified the settings correctly and set the Network Status field to "Hidden" it still wont find it unless I turn on the SSID broadcast.
I have had some awkward devices that need this to be turned on when they were initially configured, but the N82 will actually lose the connection as soon as I turn it off again.
I've tested this with two different models of access points and get the same behaviour with both.
Mobile Device:
v11.0.117
10-12-07
RM-313
Nokia N82(68.02)
Access Point 1:
Netgear WG602v3
Firmware v1.2.5
Encryption: WPA/PSK
Access control by MAC enabled
Access Point 2:
3Com OfficeConnect Wireless 11g Cable/DSL Gateway
Firmware v1.02.15
Encryption: WPA/PSK
Access control by MAC enabled
I don't know if my N82 firmware is up-to-date. I haven't tried updating it since I'm running Vista and waiting for the NSU issues to be resolved.
Cheers,
Barry.

This has been an issue on many nokia smartphones. It's possible that it was fixed in the v20 firmware update as it did include some WLAN tweaks.
You should try to get your phone updated. Do you have access to a friends XP machine?
Some people have said that the updater works on vista if you run it in XP compatibility mode. I've not tried it myself and it's entirely at your own risk.
Just out of interest does it work if you change the security type to WEP?
Message Edited by psychomania on 31-May-2008 01:54 PM

N82 Wlan - manual IP to router?

I need help for my N82.
I changed my router:
- no DHCP
- mac address filter
- wpa2
- manual roter IP address (192.168.2.1)
If I will connect with my mobile, than I can't, because I can't change IP.
I need, how can I give manual IP and gateway IP in mobile!
I tried with DHCP nothing happend.
I will give:
- my ip: 192.168.1.105
- subnet mask: 255.255.255.0
- gateway: 192.168.2.1
- DNS: 192.168.2.1
Any idea?
Solved!
Go to Solution.

Edit the access point, and then select Options -> Advanced Settings. You can do the manual config from there.

N82 wlan

i have N82 . and i also have wlan connection but when i try to access it from my mobile it does nor get connected and the error comes"web:nogateway reply.please help

Hi, I'm using N82 and had same problems before, but now have found the solution after fiddling with all options available on phone. I just hope this can solve your (and everyone else's) issue(s) on this subject. But if it fails, then I'm afraid I cant help any further (as mine is OK).
PROBLEM: It used to be that whenever I had free WIFI coverage, my N82 discovers WLAN, it refuses connection when opening browser by responding 'no gateway connection' etc.
CAUSE: My phone was actually trying to open browser under 'default' connection settings, which in my case was my home WLAN AP.
SOLUTION: Open web browser (and stop process if required), then go to Bookmark manager and select 'Edit'. Here, WLAN connection is set via 'Connection' or sumthing, where its normally set to 'Default'. Now change this to 'Ask me manually' or something (Sorry-my N82 is out of battery right now so cant find the exact words). And trying again at WIFI areas should be A-OK!
Adlan
Malaysia

No gateway replay N82

Similar Messages

Maybe you are looking for