No Global Configuration Mode?

Question

I'm sure this has something to do the RAM or Flash memory.  This is an access point that's been sitting on the shelf and as far as I knew it was working.  However, I can enter privileged mode but there is no "conf t" or configure terminal option.  I tried holding down the Mode button on reboot but it didn't seem to change anything.  I'm just trying to gain access to the gui.  I see the IP address from an IP scanner I have but am not able to access it via web browser.  This is all I'm seeing from priveledged mode.
 cd               Change current directory
  clear            Reset functions
  clock            Manage the system clock
  crypto           Encryption related commands.
  debug            Debugging functions (see also 'undebug')
  delete           Delete a file
  dir              List files on a filesystem
  disable          Turn off privileged commands
  enable           Turn on privileged commands
  exit             Exit from the EXEC
  fsck             Fsck a filesystem
  help             Description of the interactive help system
  led              LED functions
  lock             Lock the terminal
  login            Log in as a particular user
  logout           Exit from the EXEC
  mkdir            Create new directory
  more             Display the contents of a file
  name-connection  Name an existing network connection
  no               Disable debugging functions
  ping             Send echo messages
  pwd              Display current working directory
  release          Release a resource
  reload           Halt and perform a cold restart
  rename           Rename a file
  renew            Renew a resource
  rmdir            Remove existing directory
  save             Start to save raise_interrupt_level stack
  send             Send a message to other tty lines
  set              Set system parameter (not config)
  show             Show running system information
  systat           Display information about terminal lines
  terminal         Set terminal line parameters
  test             Test subsystems, memory, and interfaces
  traceroute       Trace route to destination
  undebug          Disable debugging functions (see also 'debug')
  upgrade          Upgrade software
  verify           Verify a file
  where            List active connections
Thanks for the help.

Answer 1

Yes, here is the output:
AP001e.f7ee.4d02>enable
AP001e.f7ee.4d02#show version
Cisco IOS Software, C1130 Software (C1130-RCVK9W8-M), Version 12.3(7)JX9, RELEAS                                                                                        E SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Tue 17-Jul-07 00:40 by tinhuang
ROM: Bootstrap program is C1130 boot loader
BOOTLDR: C1130 Boot Loader (C1130-BOOT-M) Version 12.3(8)JEA, RELEASE SOFTWARE (                                                                                        fc2)
AP001e.f7ee.4d02 uptime is 22 hours, 6 minutes
System returned to ROM by power-on
System image file is "flash:/c1130-rcvk9w8-mx/c1130-rcvk9w8-mx"
cisco AIR-AP1131AG-A-K9    (PowerPCElvis) processor (revision A0) with 24566K/81                                                                                        92K bytes of memory.
Processor board ID FTX1224T0LZ
PowerPCElvis CPU at 262Mhz, revision number 0x0950
Last reset from power-on
1 FastEthernet interface
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 00:1E:F7:EE:4D:02
Part Number                          : 73-8962-12
PCA Assembly Number                  : 800-24818-11
PCA Revision Number                  : B0
PCB Serial Number                    : FOC12225C3J
Top Assembly Part Number             : 800-29230-01
Top Assembly Serial Number           : FTX1224T0LZ
Top Revision Number                  : A0
Product/Model Number                 : AIR-AP1131AG-A-K9
Configuration register is 0xF
AP001e.f7ee.4d02#