No image with component cable through receiver?

I have just purchased an Apple TV device, since my HDMI Input in my projector is not working everything is not plugged in my receiver with component cable. here is a list of what my audio/video setup is :
- Sony PS3 (Plugged in Receiver in Component (Video) Optical (Audio)
- HD-DVD Toshiba (Plugged in Receiver in Component (Video) Optical (Audio)
- Bell ExpressVu HD/PVR Receiver (Plugged in Receiver in Component (Video) Optical (Audio)
- Denon AVR-5805 (Out to Projector in Component)
- Hitachi HD-PJ52
the problem is that i'm not getting any signal from my apple tv when I selected it with my receiver, not much of a mac guy, so not sure where to start....is there an on/off switch on this thing...
thank you

sorry everything is NOW plugged in my receiver with component cable

Similar Messages

What is best fiber optic to analog converter to use with RCA cables to receiver?

What is best fiber optic to analog converter to use with RCA cables to receiver?

OK, in that event I would get a Toslink to analog converter. There are many sources for these, such as Monoprice and Amazon. They are not expensive.
The fiber optic cable itself is incredibly cheap. Practically free. Don't spend a lot of money on one.

My 4s worked fine displaying on tv with component cables, but after a while the tv displayed a black screen that said signal is playing on tv. Any input for a solution?

My 4s cannot display on tv with component cable

What TV (brand and model #)?
Have you the Apple TV on another port? Used a different HDMI cable?
Are you able to cycle through the resolutions via Apple TV settings?

Poor video quality with component cable streaming from iphone to tv

Purchased a component cable on the advise of someone at the online apple store. I wanted to stream Netflix, You Tube and HBO GO from my iphone 4 to tv. Both the video and audio or are terrible! There is a constant buzz despite the fact that all connectors are tight. The video is green, squashed and looks like a 20th generation copy of an old video tape. HBO GO will only show the opening screen (which looks great for some reason) but wont play at all. Netflix and YouTube have the above issues with quality. Is this the best the $45 dollar cable will produce? If so, I wish they would have told me that! Am I doing something wrong? If not, back to the store it goes!
I have limited bandwidth and was hoping to use my 3G (which is unlimited) to avoid overages if I chose to stream movies. Any help would be appreciated!

Which iphone do you have?
Netflix only provides this feature for iphone 4, ipod touch 4th gen and ipad.

Ipod Classic doesn't play video with Component cables

I just bought a new Ipod Classic and I have it connected to my Denon receiver using the Denon dock. I am able to play music and movies from the ipod. But when I try to play movies thru my small LG tv (Apple red, rellow white component cable) I only get audio and only if I have it in the white docking station. Do I need to buy the composite cables to get the video? I do get a message stating I need to plug into a video source.
Any thoughts?
Thanks

Have tried to completely restore the iPod to factory settings and then resync the video?
Restoring iPod to factory settings
Before you do that, try converting the video once more using iTunes' built in convert. To do this, highlight the movie and chooose Create iPod or iPhone version from the Advanced drop down menu. When the conversion process is finished, sync the new version over to your iPod and see if that helps.
B-rock

Images with variables help

Ok so i want to use php to have a variable called banner and
make an image with the src being set equal to banner. I can get an
empty image with an x through it to display. When i right click it
and go to properties i find that the src isn't set to the variable
i declared.
Here's how i tried to do it:

You need to escape the image source = variable i have some
pics that i did the same thing like this:
<img src='pics/" . $picloc['name'] . "' width='$diswidth'
height='$disheight' alt='" . stripslashes($picloc['description']) .
"... Date: " . date("D F jS, Y", strtotime($picloc['upload_date']))
. "'>
yours would be like this:
echo "<img src='" . $banner . "' width='$bannerw'
height='$bannerh' alt='$sitename'>";
you might have to do the same to the alt text mine i did
because its from a RS, but just do the '" . $sitename . "' if you
need to.

No audio or video from iPod to TV with Component AV cable

I have a gen 5 80gb iPod and a Samsung tv and I can't get my iPod to play on the tv with the apple component av cables. I have run through all the different ways to set up my iPod in the video settings page. Any help on this would be great. Thanks.

after further reading I found that you can't hook up a gen 5 iPod with component av cables.

No picture using component connections with Sony STR-DG710 Receiver

I have been unable to get a picture (sound appears to be ok) using component cables to connect to a Sony 710 receiver - the (2) HDMI inputs on the receiver are taken by equipment that can not use component cables. Apple Store checked Apple TV unit and said component outlets were ok. I did barrow one of the HDMI cables to set the system up (1080i resolution was selected). Does anyone have an idea what the problem is?

There may be an easy answer here. It's your receiver - not the apple TV
1080p HDMI Inputs: The Sony receiver features two 1080p HDMI inputs and one 1080p HDMI output. The receiver transmits both audio and video through the HDMI monitor output to your TV or you can choose for the HDMI monitor out terminal to only output video to your television. Video signal that is input through HDMI input can only be output through the HDMI monitor output terminal.
Note: The receiver does not offer video upconversion.
So it looks like if you go HDMI in - you have to go HDMI out (to your TV)
If you go component in - you need to go component out (to your TV)

Ipad2 can mirroring with 'component av cable'?

(I'm foriegner.. so my english is too bozo...)
I have a ipad2.
I want to useing mirroring tech.
First purpose is 'to presentation with ipad in Keynote'
Second purpose is 'to show about ipad2 home screen(background image on application) for my presentation audience'
Third purpose is 'to see the video'(is not important)
I know 4kind of cable.
Apple Digital AV Adapter(HDMI adapter)
VGA Adapter for ipad Dock(VGA,D-sub adapter)(is it need ipad Dock? I don't have ipad Dock)
Apple component cable(3video code and 2 audio code)
Apple composit cable(1video code and 2 audoi code)(Not good at video quality)
(in korea.. we have many HDTV supporing HDMI... but not projector..
Be as usual many projector is using component code.(Only NEW monitor or NEW TV have a HDMI code))
So in my purpose...
Exactly, ipad2 + component cable are can using mirroring tech?
If it can not mirroring..
what kind of cable(or apapter) is the best?

Only way?
I know Apple AV adapter is support perfect mirroring.
but
VGA adapter is not support (perfact)mirroring?
I think this is supporting perfect mirroring screen but not audio...

My i-Pad2 won't charge after I downloaded some new stuff from i-Tunes. A note appears on the screen "Charging is not supported with this accessory". I have tried charging through two computers and with the wall socket plug (with another cable). I have

My i-Pad won't charge after I downloaded some stuff from i-Tunes. I have tried charging through two computers and using the wall socket,, with different cables. I have turned the i-Pad off & on a couple of times but it still won't charge. Any ideas will be gratefully received.

The quickest way (and really the only way) to charge your iPad is with the included 10W USB Power Adapter. iPad will also charge, although more slowly, when attached to a computer with a high-power USB port (many recent Mac computers) or with an iPhone Power Adapter (5W). When attached to a computer via a standard USB port (most PCs or older Mac computers) iPad will charge very slowly (but iPad indicates not charging). Make sure your computer is on while charging iPad via USB. If iPad is connected to a computer that’s turned off or is in sleep or standby mode, the iPad battery will continue to drain.
Apple recommends that once a month you let the iPad fully discharge & then recharge to 100%.
How to Calibrate Your Mac, iPhone, or iPad Battery
http://www.macblend.com/how-to-calibrate-your-mac-iphone-or-ipad-battery/
At this link http://www.tomshardware.com/reviews/galaxy-tab-android-tablet,3014-11.html , tests show that the iPad 2 battery (25 watt-hours) will charge to 90% in 3 hours 1 minute. It will charge to 100% in 4 hours 2 minutes. The new iPad has a larger capacity battery (42 watt-hours), so using the 10W charger will obviously take longer. If you are using your iPad while charging, it will take even longer. It's best to turn your new iPad OFF and charge over night. Also look at The iPad's charging challenge explained http://www.macworld.com/article/1150356/ipadcharging.html
Also, if you have a 3rd generation iPad, look at
Apple: iPad Battery Nothing to Get Charged Up About
http://allthingsd.com/20120327/apple-ipad-battery-nothing-to-get-charged-up-abou t/
Apple Explains New iPad's Continued Charging Beyond 100% Battery Level
http://www.macrumors.com/2012/03/27/apple-explains-new-ipads-continued-charging- beyond-100-battery-level/
New iPad Takes Much Longer to Charge Than iPad 2
http://www.iphonehacks.com/2012/03/new-ipad-takes-much-longer-to-charge-than-ipa d-2.html
Apple Batteries - iPad http://www.apple.com/batteries/ipad.html
Extend iPad Battery Life (Look at pjl123 comment)
https://discussions.apple.com/thread/3921324?tstart=30
New iPad Slow to Recharge, Barely Charges During Use
http://www.pcworld.com/article/252326/new_ipad_slow_to_recharge_barely_charges_d uring_use.html
Tips About Charging for New iPad 3
http://goodscool-electronics.blogspot.com/2012/04/tips-about-charging-for-new-ip ad-3.html
Prolong battery lifespan for iPad / iPad 2 / iPad 3: charging tips
http://thehowto.wikidot.com/prolong-battery-lifespan-for-ipad
In rare instances when using the Camera Connection Kit, you may notice that iPad does not charge after using the Camera Connection Kit. Disconnecting and reconnecting the iPad from the charger will resolve this issue.
 Cheers, Tom

A/V Component cables no longer able to work with iPhone 1st Generation?

I purchased the Apple A/V Component cables to be able to hook my iPhone up to my stereo at work and TV at home. Before the 2.0.1 update, it worked ok. No hassles or problems what so ever. Now, after the 2.0.1 update, I can no longer use this device for what it seems it was made for. It seems that now it's a $50 iPhone charger and that's about it. Anyone know of any fix or maybe something I did to make this happen? I called Apple and they said "that's odd, it should be working" and then asked if I could bring it in.
Any help would be greatly appreciated.
Message was edited by: Chargehammer

It seems it's not just the A/V Component cables that aren't working with the new upgrade. Apparently some other people have had issues with docking stations and speaker extensions after the upgrade. Anyone?

I have an Retina display MacBook Pro with HMDI out port. I also have an HDMI to Component cable with Audio Plugs. How can I get HDMI out to work with this cable when plugged into the Component and Audio ports on my TV?

I have an Retina display MacBook Pro with HMDI out port. I also have an HDMI to Component cable with Audio Plugs. How can I get HDMI out to work with this cable when plugged into the MacBook Pro and connected to the TVs Component and Audio in ports.

Will not work. To my knowledge, dual converting like that isn't supported. The Mac must detect the connected video output device and that sort of info cannot be done across an analog component uni-directional connection.

I use "hdmi to component converter" to connect apple tv with my old plasma tv by component cable. Sound is ok but the picture split 2screens left and right. Still can't fix it. Anyone can help or has any idea? should I try convert to av?

I use "hdmi to component converter" to connect apple tv with my old plasma tv by component cable. Sound is ok but the picture split 2screens left and right. Still can't fix it. Anyone can help or has any idea? should I try convert to av?

Your TV hasn't entered some odd picture in picture mode has it with two 'inputs' side by side?
AC

IPod Touch (2nd gen) - Does not work with Component AV Cable

I have a 2nd generation iPod Touch. Today I bought the component AV cable at the Apple store (along with a universal dock). Connected it correctly to the TV and:
1. No picture (screen is blue, as though nothing connected); no sound (whether video or music)
2. Whatever video is playing on the actual iPod gets stuck - as though it is on "pause", with the difference that you can push "play" and "pause" and the only thing that does is change the "play" or "pause" icon from one to the other or vice-versa--video will not actually play
3. Setting Widescreen to "on" or "off" has no effect
4. Tried connecting it to an old iPod Nano (2nd gen I think) - also no sound.
Please advise!

Alex_K
Try changeing your TV out setting, found in the (Settings) of your ipod. Following Paragraph found in the iPod User manual (Page 98): http://support.apple.com/manuals/#ipodtouch
"Use these settings to set up how iPod touch plays videos on your TV. For more
information about using iPod touch to play videos on your TV, see “Watching Videos
on a TV” on page 39.
Turn widescreen on or off: Choose Video and turn Widescreen on or off.
Set TV signal to NTSC or PAL: Choose Video > TV Signal and select NTSC or PAL.
NTSC and PAL are TV broadcast standards. iPod touch displays NTSC 480p/PAL 576p
when attached to a TV using a component cable, or NTSC 480i/PAL 576i using a
composite cable. Your TV might use either of these, depending on where you bought
it. If you’re not sure which to use, check the documentation that came with your TV. "
Hope that helps,
Weston

Apple iPhone 4 Dock not working with Apple A/V Component Cables.

Okay, Got a problem here, or I think its a problem. I purchased the iPhone 4 dock and the A/V component cables with power connection. When I connect the A/V cables to the iphone, they work fine and I see the video and hear the audio on the tv. When I connect the A/V cables to the iphone 4 dock, then place the iphone 4 on the dock it DOES NOT send the audio and video feed to the TV but it does charge the iphone.
The iPhone 4 dock, on Apple Store website says, its compatible.
From Apple Site...
(Charge and sync your iPhone 4 with the iPhone 4 Dock. Your iPhone 4 sits upright in the dock as it syncs or charges, so it's perfect for a desk or countertop. It features a convenient audio line out port that connects to powered speakers. It supports other iPad accessories, such as iPhone AV cables and the USB Power Adapter. You can even conduct speakerphone calls with your iPhone 4 in its dock.)
Is anyone else having this problem ?

Okay, Got a problem here, or I think its a problem. I purchased the iPhone 4 dock and the A/V component cables with power connection. When I connect the A/V cables to the iphone, they work fine and I see the video and hear the audio on the tv. When I connect the A/V cables to the iphone 4 dock, then place the iphone 4 on the dock it DOES NOT send the audio and video feed to the TV but it does charge the iphone.
The iPhone 4 dock, on Apple Store website says, its compatible.
From Apple Site...
(Charge and sync your iPhone 4 with the iPhone 4 Dock. Your iPhone 4 sits upright in the dock as it syncs or charges, so it's perfect for a desk or countertop. It features a convenient audio line out port that connects to powered speakers. It supports other iPad accessories, such as iPhone AV cables and the USB Power Adapter. You can even conduct speakerphone calls with your iPhone 4 in its dock.)
Is anyone else having this problem ?

No image with component cable through receiver?

Similar Messages

Maybe you are looking for