No input with Blackmagic Decklink SDI 9.7.7 and Adobe Premiere

Hi there
My BM Decklink is properly installed: I can grab Video with the BM Software.
In Adobe Premiere there is no signal. The TC is ok and running.
All Settings seems to be ok.
I'm running a Windows7/64 Bit
Thank for your help.

Yes, its an HD sequence, I want to view it in component but I'm using a SDI-Monitor also (which strangely gets an audio signal, but still no video)
I can't find anything like that in the 'Select output processing'-box, even after updating to 9.7.8 (released on Friday)...
It doesn't make any sense to me. Why would it work with AE and BM Media Express but not with Premiere CC?
My BM Decklink is not the newest model, but I don't think thats the problem.
It still seems to be supported by the software and it works with AE.
I'm going to change my graphic card from GTX 780 to NVIDIA quadro, lets see whether that will get me the result I'm hoping for, but tbh I'm giving up...

Similar Messages

Two BlackMagic DeckLink SDI Cards in FMLE

Is it possible to run two BlackMagic DeckLink SDI cards in two separate instances of Flash Media Live Encoder?
I can run one fine, but if I try to select the other, even if card # 1 [Decklink Video Capture in FMLE] is not in use, card #2 [Decklink Video Capture (2) in FMLE] only shows black. I have verified that video signal is working. Finally I installed Wirecast Demo to test if it was software and sure enough it works fine in Wirecast, each card shows the video fine.
I contacted BlackMagic and they stated it was the software. I have successfully done this with Viewcast Cards but now that we went HD BlackMagic are cheaper, but so far no luck in FMLE.
I would appreciate any isnight on this issue.
Thank you!
-Nate

Hi Pi,
Did you manage to resolve the problem? We're having similar issue. BM Media Express software recognises the card, but FMLE just reports it as Decklink and gives a blank input display. Any attempt to change settings causes FMLE to crash.
Thanks,

Capturing device offline with BlackMagic DeckLink Quad

Hi guys,
I have a problem capturing with a BlackMagic DeckLink Quad and Premiere Pro CS6. Capturing with the Blackmagic included Media Express software works fine. However, Premiere Pro tells me that my capturing device is offline.
What I did to run the capture:
Open Premiere Pro CS6
New project --> set capture to Blackmagic capture --> press ok
New sequence dialog --> select format exactly like specified in system control panel of BlackMagic (1080 25p).
Open capture dialog with F5 key.
Tells me that the capturing device is offline.
Controlling capturing properties for Blackmagic Capture and ensuring that they match the system control panel specs and the specs used in the other software(1080 25p, Video Format: Motion JPEG)
Final State --> Premiere Pro still tells me that the capturing device is offline and I have a black window.
I read somewhere that the installation order of driver and Premiere Pro is important, therefore I tried already both constalations (Driver, Premiere Pro - Premiere Pro, Driver ) without any success. A driver update of the Declink Quad did not have any effect.
Driver version:
Blackmagic DeckLink SDI - Date: 22.01.2015 Version: 13.4.10.868
Any help would be highly appreciated.
Best

Yes, Component is indeed not a better quality... Interesting because I did plug into a flatscreen, and I have nothing as well... So maybe it is the component out of the z1u that is not even working! Will try with another cable in case, but that may be the answer... Thank you for pointing that out! didn't even think about it...
I'm really trying to capture old HDV tapes, and always get those phantom breaks with Firewire (using another deck since it's broken on the z1u), now I'm wondering if you get less breaks doing 1080i or ProRes?? Although files are way bigger.

Can't lower framerate with Blackmagic Decklink

We have FME3 and a Blackmagic Decklink SDI 10bit, drivers v6.6. We would like to stream at 15fps, but in FME, I can't set the framerate to anything lower than 25. When choosing 15, it just jumps to 25.
Also tried changing it in the card's system driver - which I can - but then when I load up FME, its clearly still running at 29.97, and I still can't change to 15.
Any thoughts?

FMLE supports only those FPS that are supported by device.
In this case device is giving fixed FPS which is 29.97 irrespective of value selected in FMLE. You are sometimes getting 25 FPS because of unavailabity of enough CPU to encode 29 frames per second.
The only workaround in order to get 15 FPS output is to load your CPU or Increase Video frame size so that some of the frames get dropped by FMLE because of unavailablity of CPU and effective output FPS drops to 15.

How to install adobe photoshop elements 12 and adobe premiere elements 12 on a computer with no cd drive?

Hi
A few months ago I bought Adobe Photoshop elements 12 and Adobe premiere elements 12 to my old laptop. But a few weeks ago I had to buy a new computer and that one has no cd drive :S How can I install my programs on my new computer?
Thank you

There isn't much good news to offer. The first mention below is probably your only shot without purchase, unless you could find someone to transfer licenses with.
You won't be able to install a Windows version on the Mac unless you install some Windows emulation software on the Mac.
You won't be able to activate a Mac version of the software on the machine because your license/serial number is only valid for Windows.
CS5 is too old to qualify for a platform swap and Adobe no longer sells CS5 so you would have to take your chances with a third party vendor if you decided to purchase a Mac version.
Just to clarify, there is no such thing as a student version of the software... the license dictates the status of the software. So you won't be able to find a student version either

Imac blown up in electrical storm got a new one with no CD/DVD drive how do I reload my Adobe Photoshop Elements 9 and Adobe Premiere Elements 9 on iMac OS X 10.10.2

Imac blown up in electrical storm got a new one with no CD/DVD drive how do I reload my Adobe Photoshop Elements 9 and Adobe Premiere Elements 9 on iMac OS X 10.10.2

previous versions http://www.adobe.com/downloads/other-downloads.html

I bought the adobe photoshop elements 13 and adobe premiere elsements 13 in box in the store for my Mac; I've entered my 25 character product key - now I have been waiting for nearly an hour for something to happen with no luck. Ron

I bought the adobe photoshop elements 13 and adobe premiere elsements 13 in box in the store for my Mac;
I've entered my 25 character product key - now I have been waiting for nearly an hour for something to happen
with no luck. Has anyone else had this problem? I'm using MacBook Pro with Yosemite OS 10.10 etc. Help!
Ron in Fort Worth, TX

Also, Elements programs are not part of the Cloud
Photoshop Elements Forum http://forums.adobe.com/community/photoshop_elements
Premiere Elements Forum http://forums.adobe.com/community/premiere_elements

I purchased Adobe photoshop elements II and Adobe premiere elements II. They are both on one disc. My computer crasded and I had to reload Windows. I only have one serial number and it only works with photoshop II. The same serial number will not work for

I purchased Adobe photoshop elements II and Adobe premiere elements II. They are both on one disc. My computer crasded and I had to reload Windows. I only have one serial number and it only works with photoshop II. The same serial number will not work for Premiere. I dont have any other serial numbers. What do I do???

Static_Unit
I am getting a bit concerned about what is happening in your situation. Yesterday you posted your question in at least two different forums, one of them being here in the Premiere Elements Forum.
Don't Have Serial Number for Premiere, Only Photoshop?
Wherever you posted, the reply was to contact Adobe via its Adobe Chat. It is the only one who can sort out this matter for you.
In the thread cited above I offered to help you with the difficulties that you were having visualizing the Adobe Chat in its web page. I was waiting for your follow up on that in the above thread. Instead, I find your same question in a new Adobe Premiere Elements Forum thread this afternoon with no refer the prior threads or prior recommendations given you.
I will also mention again...when you buy the Photoshop Elements and Premiere Elements bundled in one packaging and with installation files for each on the same installation disc, each program has its own serial number. The Photoshop Elements serial number does not work for Premiere Elements and vice versa. The serial numbers are on labels on a box which houses the installation disc envelope(s). So, if you purchased both programs and found the Photoshop Elements serial number, then the Premiere Elements serial number should be in a label right underneath the label with the serial number for Photoshop Elements. I recall writing this in your yesterday's thread on this matter.
The moderator will no doubt be along shortly to close or delete this thread. So, just in case, please bookmark your yesterday's thread cited above so that we can continue this communication which is trying to help you.
Thanks.
ATR

Will FME work with BlackMagic Decklink card?

Has anyone used this combination of components together? I want to capture SDI and might have access to a Decklink card, and I only use FME 3.2 so want to be sure they'll work together before I spend the money. Thanks-

I'm using BlackMagic DeckLink Duo and it works fine.

IPhoto 6.0x conflict with Blackmagic Decklink 5.4.2

If you find that iPhoto is crashing when editing photos and you are running a Blackmagic Decklink you must turn OFF the Video Desktop option in the Blackmagic Control panel.

Solution is either uninstall decklink drivers or turn off video desktop

Cannon XH G1 with Intel MPro and Adobe Premiere CS3

What could go wrong with that combination?
The Premiere runs well on the Mac. The
time code jackpack, though pricey, is
recommended for proxy editing, and
the software appears to support 24F,
or does it?
The Canon XH G1 ain't cheap, but I'm
going for it, I think. I sure would like
some reassurance from someone who has
used this configuration. Unfortnately,
I'm not in NY or LA where I could just
go to the store and try it.
Thanks for any input.

You might find a better response posting this on an Adobe Premiere site.
Good luck,
x

Is there any hope for Mac users with AMD D700 graphic cards trying to run Adobe Premiere 2014 CC?

Who wants to watch a grown man cry? I spent a small fortune on a shiny new mac with 64GB Ram and to quote Larry Jordan, "I could rocket to the moon with the power of this computer." I am running OSX (10.9.5) and have a 12 gig per channel ethernet Maxx Digtial Raid with Areca cards to support 6K footage. However, editing my first project in Premiere CC2014 (leaving FCP 7) has been nothing short of problematic. At first, it plays great but after 20 minutes of editing, speed changes, adding secondary shots etc it starts to play choppy, freeze on certain frames playing just audio and eventually crashes or it takes a minute to render.
I did every possible thing yesterday with Adobe and Apple support. I reinstalled the OS, I trashed 3rd party preferences, trashed Premiere preferences, set project settings from OpenCL to software only and I tried changing location of the Premiere Cache folder but nothing seems to work. Eventually the last Adobe support person said it was due to the AMD card and Adobe. He was emphatic that it was Apple's fault. Apple's support team said it Adobe's. Well after that, Im still stuck. Is anyone else experiencing this? Any pieces of the puzzle?
Is anyone else having the same experience?

The default for CPU Voltage is By CPU VID default for Adjust CPU VID is Startup which should be 1.4 volt. Since Cool'n'Quiet requires a driver to run and I also show low CPU VID in cmos it should be 1.4v but I tried with Cool'n'Quiet disabled and also tried setting CPU VID to 1.4 but have never made it to 1.4 I also tried setting it to 1.425 which is the next step and still read under 1.4.

Help with N8 and Adobe Premiere?

Hi, I am using Adobe Premiere Pro CS4 v4.1.0.
I recently got a Nokia N8 and am now trying to edit the video recordings, but am having some problems.
The phone records at 25fps 1280x720 using H.264 MPEG-4 codec, with sound in Stereo 130kbps 48 kHz.
When I create a project and load the .mp4 file into it, the first problem I see is that it reads it as 500fps and the video is only a second or 2 long.
I then interpret the footage to the correct 25fps, and the video then works fine. However, the sound seems to not be there.
I've noticed that due to Premiere interpreting it as 500fps, it thus only plays the first second or two of the sound when left as 500fps and plays all the video in that second or two, and thus when changing to the correct 25fps, it is therefore only the two seconds playing over the entire minute of video.
I also tried changing the file into other formats. The only other one that kind of worked was .mov. It allowed the sound to work perfectly, the video loaded at correct frames, however, when playing the video on premiere, it then showed black screen for most of the clip.
Have tried to find out about this online and installed a couple different codec packs and media players, but nothing helped with this problem in Adobe Premiere. However, the clip played fine in the media players, such as RealPlayer.
If anyone has any advice on this, it would be appreciated. I would prefer to fix this issue correctly rather than have to manually interpret or transcode the footage each time I want to edit it.
Btw, I also posted this question on a forum with Nokia N8 Users, and others also tried it out and had same or similar issues. They also tried on CS5 and it still didn't work.
*UPDATE* I just tested again to change the file from .mp4 to .mov by simply renaming it, and this time it loaded perfectly into Premiere. However, I have to do this on my XP computer, as my Windows 7 doesn't change the format of file by simply renaming it. Hence, I would still like help with getting it to recognise the .mp4 correctly though in the first place, rather than having to rename my files each time on the XP computer.

Moshpit84 did you utilize the uninstallers located in Applications/Utilities/Adobe Installers to remove your installation of Premiere Pro? Also what version of the Adobe Application Manager are you currently using?

Best way to work with FCP files and Adobe Premiere

Hi,
I have a bit of a technical problem. I'm editing a doco for broadcast on TV and have shot on HDV and downloaded onto our system as PAL, Apple Pro Res 422, 25 fps. oowever, Our graphics editor is on Adobe Premiere CS4.
What is the best way to get it onto her system and back off again and onto ours, with the mimimum or no loss of quality?
I've heard that an XML might work, but will it work on Adobe CS4? I don't know how this will pan out if it's XML. Will we be able to open it all back up in FCP when she hands it back. What sort of file do we get back from the Adobe Prem Pro Cs4 system?
I'm a bit nervous about it all.
Hope you can help.
Cheers,
Margie

This got me curious Eagleray as I do this all the time within my Mac FCS to CS all the time. But to a PC got me a googlin. Hope this discussion _http://www.animotion.nl/en/tutorials/fcp-xml-premiere-pro-cs5/_ helps as quite a few students seem to have Macs at school and PCs at home. Also do be aware of the different formatting of some PC drives like FAT16, FAT32, NTFS vs the Mac GUID. The Mac can read them all with the proper system addons/drivers, they show up in System Preferences Preference Panes under "OTHER". I use NTFS-3G to mount NTFS PC drives. I think it was free, if not there is another one I used to use that is free from some open source NTFS group. FAT has the size limit issue of I think 2 or 4gb (you can't copy anything bigger than that at one time to a Mac from a FAT drive). I'm on Snow Leopard on my 8core. My partner who edits in PP CS3 on a PC brought over his Maxtor USB the other day for me to copy some video files from and it's been having problems mounting, I believe since I upped to SL. I threw it on my 6 year old PowerBook G4 running 10.5.8 and it mounted right away. Just another weird gotcha. But take a quick look, tho the title says CS5 in it, a few students were using CS4 on a PC.
Message was edited by: TimeKoder13
Message was edited by: TimeKoder13

Highpoint driver conflict with Blackmagic Decklink ?

a reader report over on the xlr8yourmac website notes a conflict between the HighPoint Technologies driver for the RocketRAID 1820A and the Blackmagic Design DeckLink 5.1.2 drivers.
http://www.xlr8yourmac.com/index.html#S20146

Thanks for this heads-up post, Andy.
I am ordering a Quad-core today, and I have an external SATA array. I don't have a BMD card, but I did anticipate the Highpoints Mac driver would need to be tweaked. They had to tweak the Mac driver for their PCI-X card as well.
Hopefully, I can wait for Sonnet to release a PCIe SATA card with at least four external channel ports. I'll need to delay or turn down any projects requiring uncompressed video until this is squared away.

No input with Blackmagic Decklink SDI 9.7.7 and Adobe Premiere

Similar Messages

Maybe you are looking for