No internet access on VLANs with RV042G and SG300

I'm trying to set up a network for a small business which will have different offices, and so I want to separate them all by VLAN so that they cann't access each other's files. The problem is that I can't access the internet from any of the VLANs, including the default.
The RV042G router is connected to the internet through the WAN1 port and has a static IP address of 10.4.1.1. I enables multiple subnets and added one for each of the VLANs (1 - admin, 10, 20, 30, 100 - guest). I also created static routes to the SG300 switch, which has an IP address of 10.4.1.2, 10.4.10.2, etc. The switch is in Layer 3 mode and is functioning as the DHCP server. I also have a wireless access point set up that broadcasts an SSID for each VLAN, however this is not the issue since no internet connection can be established wirelessly or with a wired connection.
I am fairly certain it has something to do with the data not being correctly routed through from the internet to the client, however I can't seem to find what is configured incorrectly. If anyone could offer some suggestions it would be appreciated. Please let me know if you need more info, I have attached some of the configuration screens for reference.

Hi Paul,
Thanks for the suggestion, but I changed it from Gateway to Router and this didn't fix the problem, still no internet access.
I have a cabel modem box that connects to the RV042G through WAN1, and then the RV042G connects to the SG300 through port 1 on the RV042G. On the RV042G, this port is set to VLAN1, while the port on the SG300 is set as a trunk port. The SG300 is then assigning IP addresses to the clients. It has 4 different VLANs created that go to different offices. Does this help you understand the setup any better?

Similar Messages

Unable to receive internet connection over wifi connection. Shows that I am connected to the network, but do not have internet access. Checked my firewall and turned it off. What else am I missing or should be doing differently?

Unable to receive internet connection over wifi connection. Shows that I am connected to the network, but do not have internet access. Checked my firewall and turned it off. What else am I missing or should be doing differently?

You might want to try resetting your router and your modem - just unplug the cords, leave them unplugged for about 3-5 minutes and then replug the modem and then the router in that order.
This may or may not correct your problem - call back if it doesn't.
Clinton

No internet access for vlan devices

Hey folks,
I'm new to cisco and have only recently started study for my ccna. In preperation for this i've gotten my hands on a cisco emi 3550-48 port switch so i can play and test some scenario's.
Now, I've setup a couple of vlans (200,201 and 202) and i've assigned them to fa0/3, 0/5 a0/7 respectively. i suppose it's irrelevant which ports are assign, they are just the ports i've assigned while typing this.
I know the cisco forums are full of people saying the intervlan routing isnt working and it just turns out to be the static route on the router in the end but i have set all that up and i can not get internet access on my vlan networks. The wierd thing is the switch itself can ping the internet no problem.
Here is my setup :
I've assigned ip addresses as follows :
vlan 200 - 10.10.200.254/24
vlan 201 - 10.10.201.254/24
vlan 202 - 10.10.202.254/24
I then enabled intervlan routing by issueing "IP ROUTING"
At this point I configured the VDSL modem/router (zyxel F1000) on IP Address 192.168.1.2/30 and I configured interface fa0/1 with the following commands :
interface fa0/1
no switchport
ip address 192.168.1.1 255.255.255.252
no shutdown
I then set the default route using :
ip route 0.0.0.0 0.0.0.0 192.168.1.2
Finally I configured three static route's on my Zyxel F1000 modem/router to send traffic back to my three vlans using the gateway 192.168.1.1
As i said above, If I plug into fa 0/3 (vlan 200) and lets say I give myself an ip address of 10.10.200.20, 255.255.255.0 and gateway 10.10.200.254. I can ping the othe vlns and devices on the other vlans no problem but bot for love nor money can i get onto the internet. For clarifications sake my dns is set to 8.8.8.8
Stranger still is the fact that the switch can ping hostnames and ips on the internet no problem. Has anyone got any ideas what could possibly be wrong?? I'm completely stumped.
Regards,
Thomas Quigley

Hey guys,
Thanks for the speedy replies. I have been trying this for about 2 weeks now and last night after posting this message to the cisco forums I got my hands on an old Sonicwall router. I decided to test the connection using this as I suspected that Zyxel router is buggy.
I setup a PPPoE connection on the sonicwall and set that up as my default route matching exactly the ip settings listed above and it worked immediately.
I knew the setup I had ran above was right it was just tormenting me that it wouldn't work. Turns out its the piece of crap Zyxek VDSL modem.
Thanks for taking the time to read my post and offer advice.
Cheers,
TQ

VLAN with PAT and 3 networks...I need help with design!

I've been tasked with a major upgrade to my current network and internet access.
1.     I need to have an internal private network with access to the internet. This will be for large meetings, and I'll use a private network with 2048 addresses.
2.     I also will have a small publid network with 8 routable addresses for Firewall, Web Server, PAT (NAT overload) for the above Private network internet access.
3.     I want to split a class C address into two networks to allow one network (128 addresses) for Guest use that need routable addresses, and a second network (the other 128 addresses) for specific meetings that also need routable addresses.
I have:
I have been issued a router from my ISP. They have allocated me one .248 network with 8 addresses (6 usable) and a full class C network.
A Cisco 1841 router with 2 FA ethernet ports. I would like to use one FA port at the outside (to my ISP router) and the other FA port as my Inside port (to all other networks). I will do NAT Overload.
I also have a Layer 3 Catylist 3750 switch.
Do I need to set up VLANs for each Network?
Can I place my network hardware on the 10 network?
Do I need router sub interfaces for my VLANs and can I PAT on a Subinterface?

Hi Brian
1. Do I need to set up VLANs for each Network?
Create seperate VLANS for each subnet and do the intervlan routing on 3750
2. Can I place my network hardware on the 10 network?
Yes
3. Do I need router sub interfaces for my VLANs and can I PAT on a Subinterface?
Not required. You can do the intervlan routing on your Layer 3 3750 switch. From 3750 you can point a default-route to the router.
On the router you can perform PAT based on an ACL. Also you need to add Static NAT for your Webserver etc
Thank you
Raju

How to share internet access from iPhone with home LAN

Hello,
Sorry if this has been asked before, but I just bought an iPhone and am trying to use it to provide internet access to a LAN at my cottage where only dial-up is possible with my ISP. Although this is easily accomplished by enabling internet sharing on my iMac and plugging it into my router's WAN port, I do not have any access to my IP printer or to my SONOS music system. Any pointers?
Thanks,
Martin Girard

Well, getting internet access for my iMac is straightforward using USB tethering (I live in Canada, no AT&T crap). Then, I can share this connection with other computers (via ethernet in my case) by enabling internet sharing (in the Sharing control panel). My problem is that once I plug my iMac in the WAN port of my router, I can't access my LAN anymore. Any ideas???

Cannot install Firefox. WHen I click on the link to install, it takes me to an "error loading page" notice. My network connection and internet access are normal with Internet Explorer, so this is not the issue. Some kind of conflict with my settings or pe

Cannot install Firefox. When I click on the link on the Mozilla website, it goes to an "error loading page". My network connection and Internet Explorer are fuctioning normally.
== computer was recently wiped clean and am now reinstalling all previous software and applications ==
== User Agent ==
Mozilla/4.0 (compatible; MSIE 6.0; Windows NT 5.1; SV1; .NET CLR 1.1.4322; .NET CLR 2.0.50727)

None of the stuff in " http://kb.mozillazine.org/Locked_or_damaged_places.sqlite " helps. I have tried and tried and I have even wipe the computer clean still didn't help. I got the same problem as he/she has got in the first posted. Can add some web pages but not all the web pages I want.. I should have never updated to 3.6.13... That's when it all started for me, from that version..... Now Version 3.6.14 is out, I was hoping the version 3.6.14 might would fix the problem wrong again....
Funny thing is i can not even Bookmark Firefox.com!!!!!...lol
So any ideas on how to fix it other than the link giving would help.
Thanks.

No Internet Access ASA 5510 with Site to Site VPN

I have inherited an ASA5510.
We have configured a site to site VPN between it and a Juniper SRX550. The Site to Site VPN works fine but users behind the ASA can not see the Internet. I'm pretty sure I'm missing something. Any help would be greatly appreciated.
Thanks
Here is the Confg
: Saved
ASA Version 9.0(4)
hostname ciscoasa
enable password m.EmhnDT1BILmiAY encrypted
xlate per-session deny tcp any4 any4
xlate per-session deny tcp any4 any6
xlate per-session deny tcp any6 any4
xlate per-session deny tcp any6 any6
xlate per-session deny udp any4 any4 eq domain
xlate per-session deny udp any4 any6 eq domain
xlate per-session deny udp any6 any4 eq domain
xlate per-session deny udp any6 any6 eq domain
passwd 2KFQnbNIdI.2KYOU encrypted
names
ip local pool RA_VPN_Hosts 10.10.1.200-10.10.1.225 mask 255.255.255.0
interface Ethernet0/0
nameif Outside
security-level 0
ip address 209.112.49.2 255.255.255.192
interface Ethernet0/1
nameif inside
security-level 100
ip address 10.10.10.1 255.255.255.0
interface Ethernet0/2
shutdown
nameif DMZ
security-level 50
ip address 10.10.11.1 255.255.255.0
interface Ethernet0/3
no nameif
no security-level
no ip address
interface Management0/0
management-only
nameif management
security-level 100
ip address 192.168.1.1 255.255.255.0
boot system disk0:/asa904-k8.bin
ftp mode passive
clock timezone GMT 0
object network obj-10.10.11.0
subnet 10.10.11.0 255.255.255.0
object network obj-10.10.1.0
subnet 10.10.1.0 255.255.255.0
object network NETWORK_OBJ_10.10.1.192_26
subnet 10.10.1.192 255.255.255.192
object network NETWORK_OBJ_10.10.1.0_24
subnet 10.10.1.0 255.255.255.0
object network NETWORK_OBJ_10.10.10.0_24
subnet 10.10.10.0 255.255.255.0
access-list Split_Tunnel_list standard permit 10.10.1.0 255.255.255.0
access-list Split_Tunnel_list standard permit 10.10.10.0 255.255.255.0
access-list Outside_cryptomap extended permit ip 10.10.10.0 255.255.255.0 10.10.1.0 255.255.255.0
access-list Outside_cryptomap extended permit ip object obj-10.10.1.0 10.10.10.0 255.255.255.0
access-list inside_access_in extended permit ip any any
access-list inside_access_in extended permit ip any any4
access-list Outside_access_in extended permit ip any any
access-list global_access extended permit ip any any
access-list s2s extended permit ip object NETWORK_OBJ_10.10.10.0_24 any
access-list s2s extended permit ip 10.10.1.0 255.255.255.0 10.10.10.0 255.255.255.0
pager lines 24
logging enable
logging asdm informational
mtu Outside 1500
mtu inside 1500
mtu DMZ 1500
mtu management 1500
no failover
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-731-101.bin
no asdm history enable
arp timeout 14400
no arp permit-nonconnected
nat (inside,Outside) source static obj-10.10.1.0 obj-10.10.1.0 destination static NETWORK_OBJ_10.10.1.192_26 NETWORK_OBJ_10.10.1.192_26 no-proxy-arp route-lookup
object network obj-10.10.1.0
nat (any,Outside) dynamic interface
access-group Outside_access_in in interface Outside
access-group inside_access_in in interface inside
access-group global_access global
route Outside 0.0.0.0 0.0.0.0 209.112.49.1 1
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
http server enable
http 192.168.1.0 255.255.255.0 management
http 10.10.1.0 255.255.255.0 inside
http 10.10.10.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
sysopt connection preserve-vpn-flows
crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS esp-aes esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS mode transport
crypto ipsec ikev2 ipsec-proposal AES256
protocol esp encryption aes-256
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES192
protocol esp encryption aes-192
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES
protocol esp encryption aes
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal 3DES
protocol esp encryption 3des
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal DES
protocol esp encryption des
protocol esp integrity sha-1 md5
crypto ipsec security-association pmtu-aging infinite
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map Outside_map 1 match address Outside_cryptomap
crypto map Outside_map 1 set pfs group1
crypto map Outside_map 1 set peer 209.171.34.91
crypto map Outside_map 1 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map Outside_map 1 set ikev2 ipsec-proposal AES256 AES192 AES 3DES DES
crypto map Outside_map 1 set ikev2 pre-shared-key *****
crypto map Outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map Outside_map interface Outside
crypto ca trustpool policy
crypto ikev2 policy 1
encryption aes-256
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 10
encryption aes-192
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 20
encryption aes
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 30
encryption 3des
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 40
encryption des
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 enable Outside
crypto ikev1 enable Outside
crypto ikev1 ipsec-over-tcp port 10000
crypto ikev1 policy 10
authentication crack
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 20
authentication rsa-sig
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 30
authentication pre-share
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 40
authentication crack
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 50
authentication rsa-sig
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 60
authentication pre-share
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 70
authentication crack
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 80
authentication rsa-sig
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 90
authentication pre-share
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 100
authentication crack
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 110
authentication rsa-sig
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 120
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 130
authentication crack
encryption des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 140
authentication rsa-sig
encryption des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 150
authentication pre-share
encryption des
hash sha
group 2
lifetime 86400
telnet timeout 5
ssh 10.10.10.0 255.255.255.255 inside
ssh timeout 5
console timeout 0
management-access inside
dhcpd address 192.168.1.2-192.168.1.254 management
dhcpd enable management
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
group-policy DfltGrpPolicy attributes
vpn-filter value Outside_cryptomap
group-policy RA_VPN internal
group-policy RA_VPN attributes
dns-server value 10.10.1.5 10.10.1.6
vpn-tunnel-protocol ikev1
split-tunnel-policy tunnelspecified
split-tunnel-network-list value Split_Tunnel_list
default-domain value carepath.com
group-policy GroupPolicy_209.171.34.91 internal
group-policy GroupPolicy_209.171.34.91 attributes
vpn-filter value s2s
vpn-tunnel-protocol ikev1 ikev2 l2tp-ipsec
username cpadmin password SuNpolqZO8KYoffw encrypted privilege 15
username cpadmin attributes
vpn-group-policy RA_VPN
username steve password zKezdIDBYe0zxG6W encrypted privilege 15
username steve attributes
vpn-group-policy RA_VPN
username Forrestj password VhlOu4i/.IyOOTmy encrypted privilege 15
username Forrestj attributes
vpn-group-policy RA_VPN
username janarthan password n32zoOqGRkFKGlJB encrypted privilege 15
username janarthan attributes
vpn-group-policy RA_VPN
username Mckyedo password CcFuHnol1NALuUZs encrypted privilege 15
username Mckyedo attributes
vpn-group-policy RA_VPN
tunnel-group RA_VPN type remote-access
tunnel-group RA_VPN general-attributes
address-pool RA_VPN_Hosts
default-group-policy RA_VPN
tunnel-group RA_VPN ipsec-attributes
ikev1 pre-shared-key *****
tunnel-group 209.171.34.91 type ipsec-l2l
tunnel-group 209.171.34.91 general-attributes
default-group-policy GroupPolicy_209.171.34.91
tunnel-group 209.171.34.91 ipsec-attributes
ikev1 pre-shared-key *****
ikev2 remote-authentication pre-shared-key *****
ikev2 local-authentication pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:f49e465720761f4829d125b81e4bdc1f
: end
asdm image disk0:/asdm-731-101.bin
no asdm history enable

Please fix your ACL, please remove the first line and change the second line.
no access-list Outside_cryptomap extended permit ip 10.10.10.0 255.255.255.0 10.10.1.0 255.255.255.0
access-list Outside_cryptomap extended permit ip object obj-10.10.1.0 10.10.1.192 255.255.255.192
Thirdly add this static route.
route Outside 10.10.1.192 255.255.255.192 209.112.49.1
Fourth
Please remove these line as well.
tunnel-group 209.171.34.91 general-attributes
no default-group-policy GroupPolicy_209.171.34.91
no group-policy GroupPolicy_209.171.34.91 internal
no group-policy GroupPolicy_209.171.34.91 attributes
no vpn-filter value s2s
no vpn-tunnel-protocol ikev1 ikev2 l2tp-ipsec
and these as well.
Fifth you don't need them, remove this acl.
no access-list s2s extended permit ip object NETWORK_OBJ_10.10.10.0_24 any
no access-list s2s extended permit ip 10.10.1.0 255.255.255.0 10.10.10.0 255.255.255.0
Hope this helps.
thanks
Rizwan Rafeek

Not able to access web service with axis and tomcat

Dear all
i am trying to access web service using axis in tomcat.
i downloaded axis-bin-1_4.zip, unzipped it and installed it properly in tomcat.
i had tested axis, its working fine.
i had created a simple java class(a sample class from book) and deployed it in axis. i also created a client(a java consol class) for accessing that web service. but its giving error. i have no idea why this is comming.
plz point me in right direction.
thanks in advance
The error is:
Exception in thread "main" AxisFault
faultCode: {http://xml.apache.org/axis/}HTTP
faultSubcode:
faultString: (404)/axis/ArithmeticProcessor.jws
faultActor:
faultNode:
faultDetail:
        {}:return code: 404
<html><head><title>Apache Tomcat/6.0.14 - Error report</tit
le><style></style> </hea
d><body><h1>HTTP Status 404 - /axis/ArithmeticProcessor.jws</h
1><HR size="1" noshade="noshade"><p><b>
type</b> Status report</p><p><b>message</b> <u&
gt;/axis/ArithmeticProcessor.jws</u></p><p><b>descriptio
n</b> <u>The requested resource (/axis/ArithmeticProcessor.jws) is n
ot available.</u></p><HR size="1" noshade="noshade
"><h3>Apache Tomcat/6.0.14</h3></body></html>
        {http://xml.apache.org/axis/}HttpErrorCode:404
(404)/axis/ArithmeticProcessor.jws
        at org.apache.axis.transport.http.HTTPSender.readFromSocket(HTTPSender.j
ava:744)
        at org.apache.axis.transport.http.HTTPSender.invoke(HTTPSender.java:144)
        at org.apache.axis.strategies.InvocationStrategy.visit(InvocationStrateg
y.java:32)
        at org.apache.axis.SimpleChain.doVisiting(SimpleChain.java:118)
        at org.apache.axis.SimpleChain.invoke(SimpleChain.java:83)
        at org.apache.axis.client.AxisClient.invoke(AxisClient.java:165)
        at org.apache.axis.client.Call.invokeEngine(Call.java:2784)
        at org.apache.axis.client.Call.invoke(Call.java:2767)
        at org.apache.axis.client.Call.invoke(Call.java:2443)
        at org.apache.axis.client.Call.invoke(Call.java:2366)
        at org.apache.axis.client.Call.invoke(Call.java:1812)
        at ArithmeticClient.main(ArithmeticClient.java:50)

Hi ,
Please go through this link and check in this way only you created the webservice correctly or not. If not follow and do it definitely will get you the webservice access by iphone or any application.
www.scribd.com/doc/19255987/Web-Services-in-Abap

Internet won't work with wireless and ethernet connected at the same time. Airport extreme

Why can I not connect ot the internet when both the ethernet cable is connected. The connection is fine when only on wireless and fine when only the ethernet cable is connected but won't work when the cable is plugged in.
any ideas?

opps forgot to set router as bridge turned off NAT and problems solved

Access ni4882.dll with Qt and MinGW

I have to control some electric loads and power supplies over GPIB. We use Qt 4.7.4 with MinGW 4.4 (32-bit) on Windows 7 64-bit.
The packet NI-488.2 GPIB Drivers packet 3.0.2 for Windows 7 64-bit is installed. The GPIB Troubleshooting Utility tool shows "pass" and the Measurement & Automation application can connect to the board and talk to an intrument. So far so good.
Now I want to write an application to use the NI4882.dll (3.0.0.49153). Unfortunately, there are just object files for Microsoft and Borland compilers and no lib file.
So we generate a def file from the ni4882.dll with:
pexports -h ni4882.h ni4882.dll > ni4882.def
-ni4882.def-
LIBRARY NI4882.dll
EXPORTS
?compareVersion@nGPIBAPI_NI4882@@YGXABVtSSVersion@@0AAJPBD@Z
?getCurrentVersion@nGPIBAPI_NI4882@@YG?AVtSSVersion@@AAJ@Z
?getOldestCompatibleVersion@nGPIBAPI_NI4882@@YG?AVtSSVersion@@AAJ@Z
AllSpoll@12
DevClear@8
DevClearList@8
Then generate the lib with:
dlltool -k -D ni4882.dll -d ni4882.def -l libni4882.a
Now, I've build a small test program in Qt.
-.pro file-
INCLUDEPATH += $$PWD/include
LIBS += $$PWD/lib/libni4882.a
-.cpp file-
#include "ni4882.h"
void MainWindow::Init()
int dd = idev(0,3,0,T10s,1,0);
if(Ibsta()&ERR)
    Err(tr("Unable to open board:ibdev=%1").arg(dd));
if( ibonl(0,0)&ERR)
    Err(tr("Unable to close board"));
void MainWindow::Err(QString message)
switch(Iberr())
    case 0:
      message.append("(EDVR - System error)");
    } break;
qDebug("Error : %s\nibsta = 0x%x iberr = %d\n",
    (unsigned int)Ibsta(), (int)Iberr());
The source code will be compiled and linked without an error.
But if I run it, the output is:
Error : Unable to open board: ibdev=32768 (EDVR - System error)
ibsta = 0x8000 iberr = 0
Error : Unable to close board (EDVR - System error)
ibsta = 0x8000 iberr = 0
So, the question is: What is wrong? Why do I always receive this EDVR error. I also tried SendIFC(0) with the same result.
With the GPIB Interactive Control tool, I can communicate with my instrument and the NI I/O Trace logs it. But I can't see logs in the Trace tool from my application. Is this an indication?
Any ideas?
Marko
Solved!
Go to Solution.

Hi to all,
after some questions about using the GPIB library with Qt, I've written a step by step description to create object files for MinGW:
1. Create a folder and copy the "gpib-32.dll" from the "C:\Windows\System32" ("C:\Windows\SysWOW64" in Win7) to this folder.
2. Copy "ni488.h" from "c:\Program Files (x86)\National Instruments\Shared\ExternalCompilerSupport\C\include\". (Not ni4882.h!)
3. Load PExports (my version is 0.44) and put the exe in your folder to. I do not have a URL to load this tool but should be easy to find. It's freeware.
4. Copy dlltool.exe from "c:\QtSDK\mingw\bin\" to your folder.
5. Create a batch file "1 - build def file.bat" with the content: "pexports -h ni488.h gpib-32.dll > gpib.def"
6. Create a batch file "2 - build lib file.bat" with the content: "dlltool -k -D gpib-32.dll -d gpib.def -l libgpib.a"
7. Start the batch file "1 - build def file.bat" to create the def file "gpib.def"
8. Start the batch file "2 - build lib file.bat" to create the library file "libgpib.a"
9. Copy "gpib-32.dll" and "libgpib.a" to your software project. I created the subfolder "lib" and copied the files into.
10. Copy "ni488.h" to your software project. I created the subfolder "include" and copied the file into.
11. Into your PRO file type:
# Include the NI 488.2 library
INCLUDEPATH += $$PWD/include
HEADERS += include/ni488.h
LIBS += $$PWD/lib/libgpib.a
12. In your source code type:
#include "windows.h"
#include "ni488.h"
bool InitializeGPIBBoard( )
bool isStarting = false;
int boardID;        /** @brief Board id. */
QString boardName; /** @brief Board name. */
int boardDescr;     /** @brief Board descriptor. */
// Get board ID
SendIFC(boardID);
if( ThreadIbsta() & ERR )
    ErrorHandling(tr("Unable to open board"));
    return isStarting;
// Open and initialize a board or a user-configured device descriptor
wchar_t *aName = new wchar_t[boardName.size()+1];
m_para.boardName.toWCharArray( aName );
aName[boardName.size()] = 0;
m_para.boardDescr = ibfind( aName );
delete []aName;
// The board is the System Controller.
if( ibconfig( boardDescr, IbcSC, 1 ) & ERR )
    ErrorHandling(tr("Unable to set the board to System Controller"));
    return isStarting;
// Assert interface clear.
if( ibsic( boardDescr ) & ERR )
    ErrorHandling(tr("Assert interface clear"));
    return isStarting;
// aso.
isStarted = true;
return isStarted;
13. Be happy! :-)
I hope that helps. If you have problems, please write me a message or post on this board thread.
Gruß und viel Erfolg!
Marko

How can I prevent my screen getting covered with black and white lines while working on the internet which only happens with firefox and only go when I 'go back' or go down a page?

It happens as I surf - horizontal black and white lines particularly when I scroll down and only goes if I can go to a new page or go back a page. It is driving me crazy and only happens with firefox. I have disabled all plug ins but it still happens.

Try to disable hardware acceleration.
*Tools > Options > Advanced > General > Browsing: "Use hardware acceleration when available"
If disabling hardware acceleration works then check if there is an update available for your graphics display driver.
*https://support.mozilla.org/kb/how-do-i-upgrade-my-graphics-drivers

"No Internet Access" on connected device with mobile hotspot

I've been on Verizon for 2 weeks. Note II on a Family Share Plan with lots of data. Using the built-in Verizon Mobile Hotspot application. Connecting from my work laptop, which is Windows 7.
Set it up and everything worked fine for a week and a half. I had no problems connecting or accessing the internet from my laptop. It worked fine Monday morning. Monday afternoon my laptop started giving me the warning message "No Internet Access" when connecting to the phone's hotspot. I'm in a 4g area where the hotspot has worked previously. I've tried several times in several different 4g locations as time allowed over the last 2 days, and I have not been able to get to the internet on my connected laptop again.
While connected to the mobile hotspot I ran Windows troubleshooter and it tells me that there is no DHCP server available, and that the default gateway for this network is unreachable. My laptop has no problems reaching the internet via the wireless network at work or at home. The laptop connects to both of those wireless networks every day (both before and since this problem appeared.)
I have rebooted both the phone and the laptop, with no change in the problem results. I renamed the hotspot, and connected to the "new" hotspot from my laptop, with no change in the problem results. I have tried running "ipconfig /renew" from my laptop while connected, and that is when it tells me that it cannot find a DHCP server for this network.
What broke? How can I fix it?
I'm still in the 100% refund return period on my contract and phones (for another day or so.) This is an absolute deal-killer. Hotspot on my phone is the single reason why I switched networks.
* Revised 2/28:
This morning I turned on the mobile hotspot feature on my wife's Galaxy S3 (on the same Verizon Family Share Plan.) Then I connected to it from my laptop. When it connected it said "limited internet access" for about 30 seconds, and then that warning went away and I had full access. I surfed for a moment to confirm, and all was working. I turned off the GS3 hotspot and turned on the hotspot on my Note II. When I connected to the Note II's hotspot from my laptop I still had no internet access. I left it for 3-4 minutes, and it never switched on. I tried surfing and got only error messages in my browser.
All of this was while sitting at my desk. So I believe I have ruled out the laptop as a cause for this problem.
Thanks in advance,
Randy

After I posted the above in February I talked to Verizon support. They could not resolve the problem. They replaced the phone, and the new phone has worked for months. My work schedule changed a bit, and so I started using the hotspot less often.
Last week I noticed that after I connected my laptop I had a longer delay before it would change from "No Internet Access" to giving me access. Yesterday morning it was so slow that I got the command prompt up on my laptop and determined that from the laptop's perspective the problem was that there was no DHCP server available through the hotspot network. That morning it did eventually find the DHCP server and issue my laptop an IP address, and let me connect.
Yesterday afternoon the DHCP server never appeared, and I was not able to connect to the internet. Same thing this morning. I rebooted both the phone and the laptop. No change. The laptop connects to other wireless networks just fine, still. This worked for months. Why did it slow down connecting and then stop? I'm guessing there must be some sort of buffer that has filled up.
Anyone have any ideas?
Thanks in advance.

Iphone6 touch id stops internet access both wifi and cellular

iPhone 6 64GB iOS 8.0.2 Verizon - With Touch ID on (at least one fingerprint is configured), there are times when I depress HOME to wake the device and then try to use the fingerprint reading service, internet access stops both on wifi and cellular. Turning wifi off and on doesn't help. The wifi signal shows as OK. No subsequent internet access on either wifi or cellular. Have to restart the device (I hold the home and power buttons together until the Apple logo displays).
Right now, it is OK to not use Touch ID. In fact, since I specify how long to wait before locking the device it is actually more convenient to not use Touch ID.
However, when Apple Pay is available this will be a significant problem.
Any advice? Thank you.

I have not verified this, but I have read that the ios 6 ipad uses either the cell network or the wifi network, but not both at the same time.
You should be able to test this.
I'm not enough of a network tech to know if you could get this to work, but there are mifi devices that do wifi to cellular.
Here is one example:
FreedomPop provides 500meg of free 4g cellular data per month! You do need to buy a wireless device at $39. There are ways of getting bonus megs. One gig of addition data costs $10 per month. I used about 10megs per hour of internet surfing.
When signing up, you need to be careful with your selections. On some screens, the free option is a small link below the large button. FreedomPop employs a Pavlovian Dog < Operant conditioning > thing of getting you used to clicking on the large button then they change the large button to a paid add-on.
Once you setup your account, you need to go to your account options screen to turn off automatic paid data download once you exceed your quota.
The performance seems about like my DSL connection.
http://www.freedompop.com/offers.htm?experience=organic.default
http://www.freedompop.com/coverage
Get it before they go broke.
Robert

Control Internet access using machines names

Hello to all, I have some machines (> 100) that are DHCP client and are on different subnets. I need that users that work on these machines don't access Internet. Is a there a way on TMG 2010 to create any
kind of control to accomplish this need?
Regards, EEOC.

Hi,
You can only control the traffic with IP addresses not computer names. A other way to limit internet access is to use users and groups in TMG firewall policy rules. The clients must be Webproxy or TMG clients
regards Marc Grote aka Jens Baier - www.it-training-grote.de - www.forefront-tmg.de - www.galileocomputing.de/3276?GPP=MarcGrote

BTHH5 connected, but no internet access

Hi! I've got BT Infinity on my HomeHub 5A. Here is the problem. When I connect to my wifi everything is good, but after a while I lose internet connection. I am still connected to my wifi, but the wifi sign shows a yellow triangle with an exclamation point and says I dont have internet access.
If I disconnect and then connect again everything goes back to normal and I can browse again. This is just a temporary fix because after some time I lose access again. This can happen after an hour or just after a minute of browsing, so it can be very frustrating if it happens often.
After reading some threads on the forum I tried assigning a static DNS adress, that didnt help. Then I tried switching of the 5GHz network, that didnt help either. I have downloaded inSSIDer and changed the chanell of my wifi to a less busy one, that didnt help as well.
This happens on both Windows 7 laptops, on the PS4 and an iPhone, so the problem is not in them. Also it happens when just one laptop is connected, so the number of connected devices is not a problem also.
I dont have any options to try now, so any suggestions will help.
1. Product name:
BT Home Hub
2. Serial number:
+068543+NQ42644460
3. Firmware version:
Software version 4.7.5.1.83.8.204 (Type A) Last updated 20/01/15
4. Board version:
BT Hub 5A
5. DSL uptime:
1 days, 07:20:19
6. Data rate:
9995 / 39993
7. Maximum data rate:
27205 / 81597
8. Noise margin:
21.7 / 17.7
9. Line attenuation:
12.6 / 12.3
10. Signal attenuation:
12.4 / 12.3
11. Data sent/received:
11.9 GB / 20.2 GB
12. Broadband username:
[email protected]
13. BT Wi-fi:
Yes
14. 2.4 GHz Wireless network/SSID:
BTHub5-Q3ZK
15. 2.4 GHz Wireless connections:
Enabled (802.11 b/g/n (up to 144 Mb/s))
16. 2.4 GHz Wireless security:
WPA2
17. 2.4 GHz Wireless channel:
5
18. 5 GHz Wireless network/SSID:
BTHub5-Q3ZK5
19. 5 GHz Wireless connections:
Enabled (802.11 a/n/ac (up to 1300 Mb/s))
20. 5 GHz Wireless security:
WPA2
21. 5 GHz Wireless channel:
44
22. Firewall:
Default
23. MAC Address:
c8:91:f9:1d:f6:78
24. Modulation:
G.993.2 Annex B
25. Software variant:
AA
26. Boot loader:
1.0.0

Hi cgleb1,
Welcome to the community forum. I'll be able to take a look at your connection and run a few checks on your line.
Send me in your details using the "Contact The Mods" link found in my profile.
Thanks
PaddyB
BTCare Community Mod
If we have asked you to email us with your details, please make sure you are logged in to the forum, otherwise you will not be able to see our ‘Contact Us’ link within our profiles.
We are sorry but we are unable to deal with service/account queries via the private message(PM) function so please don't PM your account info, we need to deal with this via our email account :-)

No internet access on VLANs with RV042G and SG300

Similar Messages

Maybe you are looking for