No internet access when cellular network is available?
Folks, I'm looking for debug help. For two days now, I've had an almost complete lack of success in connecting to the Internet via my iphone.
Environment: new-since-march iphone 3G running OS 2.2, Wifi OFF, airplane mode OFF, 4 full bars ATT 3G. Can make cell phone calls.
Symptoms: third party apps (NYTimes, FB, etc) abort or timeout with a "check your internet connection". Integrated apps, like the Apps store, error with "cannot retrieve download info, please connect with itunes".
What should I try next?
skg
Reboot.
To reboot, press and HOLD both the HOME and LOCK buttons.
DO NOT let go when it says to slide to turn off, but keep holding both.
Screen will flicker off but DON'T let go.
Once you see the Apple Logo, then you can let go.
That is how to do a full cold reboot of the phone. No data or settings will be lost and only takes as long as it takes the phone to boot up.
This is the fix to just about every problem you ever may face with the phone (remember, it is a computer and a new OS at that. So reboots are needed now and then just to clear the cobwebs/memory leaks).
Similar Messages
-
Cascaded routers: no internet access when second router not use NAT
Cascaded routers: no internet access when second router not use NAT
Here is my setup:
[pre]
WAN
|
| 74.96.170.x (WAN IP) |
| Router1(Verizon FiOS Router) |
| Model: MI424WR-GEN2 (Rev F) |
| Firmware: 20.21.0.2 |
| Def router: 74.96.170.1 |
| 192.168.1.1 (Local IP) |
|
| 192.168.1.22 (WAN IP) |
| Router2(Linksys) |
| Model: WRT54GL v1.1 |
| Firmware: v4.30.16 |
| Def Router: 192.168.1.1 |
| 192.168.2.1 (Local IP) |
|
| Computer 192.168.2.160 |
| Def Router: 192.168.2.1 |
"q.route" 120L, 4441C written
[m.wang@m-wang-ltm2:/Users/m.wang/m/Network]
$ more q.route
Cascaded routers: no internet access when second router not use NAT
Here is my setup:
[pre]
WAN
|
| 74.96.170.x (WAN IP) |
| Router1(Verizon FiOS Router) |
| Model: MI424WR-GEN2 (Rev F) |
| Firmware: 20.21.0.2 |
| Def router: 74.96.170.1 |
| 192.168.1.1 (Local IP) |
|
| 192.168.1.22 (WAN IP) |
| Router2(Linksys) |
| Model: WRT54GL v1.1 |
| Firmware: v4.30.16 |
| Def Router: 192.168.1.1 |
| 192.168.2.1 (Local IP) |
|
| Computer 192.168.2.160 |
| Def Router: 192.168.2.1 |
| NO iptables, basic setup |
[/pre]
On computer, I have:
[pre]
# route
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
default 192.168.2.1 0.0.0.0 UG 2 0 0 enp2s0
loopback localhost 255.0.0.0 UG 0 0 0 lo
192.168.2.0 * 255.255.255.0 U 0 0 0 enp2s0
[/pre]
On Router2, I have:
[pre]
Routing Table Entry List
Destination LAN IP | Subnet Mask | Gateway | Hop Count | Interface
192.168.2.0 255.255.255.0 0.0.0.0 1 LAN & Wireless
192.168.1.0 255.255.255.0 0.0.0.0 1 WAN (Internet)
0.0.0.0 0.0.0.0 192.168.1.1 1 WAN (Internet)
[/pre]
Router2's Operating Mode is Gateway. On Router1, I have:
[pre]
[Router1] Routing Table
Name Destination Gateway Netmask Metric Status
Network (Home/Office) 192.168.2.0 192.168.1.22 255.255.255.0 0 Applied
Network (Home/Office) 192.168.1.0 192.168.1.1 255.255.255.0 0 Applied
Routing Protocol: Internet Group Management Protocol (IGMP)
Default Gateway: 74.96.170.1
[/pre]
On computer, I can run tcptraceroute to yahoo.com OK:
[pre]
# tcptraceroute yahoo.com
Selected device enp2s0, address 192.168.2.160, port 46596 for outgoing packets
Tracing the path to yahoo.com (206.190.36.45) on TCP port 80 (http), 30 hops max
1 192.168.2.1 0.610 ms 0.729 ms 0.735 ms
2 192.168.1.1 1.843 ms 1.378 ms 1.363 ms
3 l100.washdc-vfttp-107.verizon-gni.net (96.241.146.1) 13.620 ms * *
... /* It reached the destination. */
[/pre]
I want to change Router2's Operating Mode from "Gateway" to "Router" because I
want to turn off NAT on Router2 so that I can access all computers attached to
Router2 by their individual IP instead of using port forwarding at Router2.
The problem is after the mode change from "Gateway" to "Router", and regardless
whether I disable RIP or enable RIP, and on what interfaces it is enabled, computer
192.168.2.160 does not have internet connection.
Observations:
[0] INTRAnet works as I can reach computer 192.168.2.160 from computer behind Router1
192.168.1.x and vice versa.
[1] ping and traceroute *work* on Router2 itself using the built-in dianostic tool.
[2] nslookup on computer 192.168.2.160 always works on new lookup. It uses
192.168.2.1 as the resolver.
[3] tcptraceroute stops after step 2:
[pre]
# tcptraceroute yahoo.com
Selected device enp2s0, address 192.168.2.160, port 45999 for outgoing packets
Tracing the path to yahoo.com (98.139.183.24) on TCP port 80 (http), 30 hops max
1 192.168.2.1 2.553 ms 0.534 ms 0.638 ms
2 192.168.1.1 1.342 ms 0.964 ms 0.867 ms
3 * * *
[/pre]
[4] tcpdump shows that computer 192.168.2.160 tries to reach out and nothing is returned:
[pre]
13:34:03.172828 IP 192.168.2.160.45999 > 98.139.183.24.http: Flags [S], seq 1122548929, win 0, length 0
13:34:06.175786 IP 192.168.2.160.45999 > 98.139.183.24.http: Flags [S], seq 1122548929, win 0, length 0
13:34:09.178804 IP 192.168.2.160.45999 > 98.139.183.24.http: Flags [S], seq 1122548929, win 0, length 0
[/pre]
This is not expected because NAT to internet should still be done by Router1, no? Computer
behind Router1 with IP 192.168.1.x has internet connection.
[5] It looks like I cannot change the Routing Table Entry on Router2. I do not think I need to change anything,
just an observation.
[6] If I use LAN to LAN connection, then both intranet and internet works. [The internet IP of Router2 can be
anything not in the same subnet of the Router1, and DHCP on the local side should be disabled to avoid conflict
with the the DHCP on Router1].I have a question. Unfortunately in order to ask my question, I have to have a lengthy description of my setup. Basically, I have a second Linksys router in "router" operating mode with NAT disabled connected to the Verizon router, and I have a computer which is in a different subnet (192.168.2.x) behind the Linksys router. This computer can communicate with computers behind Verizon router in subnet (192.168.1.x), but cannot reach internet. This is a simplified version of my question, full details are in the original post.
If I setup the Linksys router in "gateway" operating mode, which means with NAT enabled, then both intranet and internet works, but there is no easy way to setup port forwarding for 10 compueters in 192.168.2.x network to communicate with 10 computers in 192.168.1.x network.
If I setup the Linksys router in a LAN to LAN configuration with Verizon routers, but this way all computers are in the same subnet, I want them to be in different subnet for access control and things like that.
I hope this makes things a little clear.
Thanks. -
I am able to connect my ipad 2 to an iphone 4s personal hotspot via bluetooth or wifi. The problem is that I only have internet access with a bluetooth connection. Both are running ios 6.1.2 and I have tried to reset both to factory settings. Any suggestions would be reatly appreciated.
Please don't shout! Using all uppercase means shouting on the internet. If your keyboard is stuck please say so, otherwise people will think you are being obnoxious.
Now the first question is, when you are saying connecting to personal hotspot, have you always been using the iPhone to connect to the internet? Are you someplace where the only place to connect is available via tethering to the iPhone's celluar network? Or do you have other options? -
No Internet access when I use a certain static IP yet other IP's are ok.
Hiya,
Strange IP issue !!!
I have a windows 2003 sevrer with a static IP.
My network has a DHCP server and that Particular IP is in the exclusion range.
When I open a browser on the server I get the error "internet explorer cannot display the webpage"
However if I change the static IP address to a defferent static Ip address everything works fine.
Here's the funny bit.
If I set a different PC to this troublesome static IP I also get the issue.
So the problem is with the Static IP address itself?
On the DHCP server there is no indication that this is a BAD IP ADDRESS etc..
Checkeded the firewall an this is not blocking either.
Any ideas why this particular IP fails to get me internet access ?
Ray..IP with no internet access (IP Issue)
Ethernet adapter Local Area Connection:
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Broadcom NetXtreme Gigabit Ethernet
Physical Address. . . . . . . . . : 00-14-5E-BD-C2-0C
DHCP Enabled. . . . . . . . . . . : No
IP Address. . . . . . . . . . . . : 10.1.3.150
Subnet Mask . . . . . . . . . . . : 255.255.254.0
Default Gateway . . . . . . . . . : 10.1.2.254
DNS Servers . . . . . . . . . . . : 10.1.3.145
10.1.3.146
IP with internet access working (Normal IP)
Ethernet adapter Local Area Connection:
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Broadcom NetXtreme Gigabit Ethernet
Physical Address. . . . . . . . . : 00-14-5E-BD-C2-0C
DHCP Enabled. . . . . . . . . . . : No
IP Address. . . . . . . . . . . . : 10.1.3.167
Subnet Mask . . . . . . . . . . . : 255.255.254.0
Default Gateway . . . . . . . . . : 10.1.2.254
DNS Servers . . . . . . . . . . . : 10.1.3.145
10.1.3.146
DNS Server
Ethernet adapter Local Area Connection:
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Broadcom NetXtreme Gigabit Ethernet #2
Physical Address. . . . . . . . . : 00-14-5E-BD-CB-20
DHCP Enabled. . . . . . . . . . . : No
IP Address. . . . . . . . . . . . : 10.1.3.145
Subnet Mask . . . . . . . . . . . : 255.255.254.0
Default Gateway . . . . . . . . . : 10.1.2.254
DNS Servers . . . . . . . . . . . : 10.1.3.145
Primary WINS Server . . . . . . . : 10.1.3.145 -
No internet access through hosted network
I created a hosted network to share the internet enabled the same. Both shared connection and the hosted network are showing 'Access type' as internet access, other guest devices are connected to the hosted network, got ip addresses also. But none of
the devices are able to access internet. I have tried disabling antivirus and firewall, but still the internet connection is not available to other devices.
Tried ‘Virtual router plus’. That also could not help in getting internet access, there in fact the internet connection sharing had to be enabled manually.
I had gone through similar issues, but could not see proper answer from an expert.
OS: Windows 8, Windows Firewall enabled
Antivirus: Trend Micro
Internet: USB modem (ICS enabled for the hosted network).
Any suggestions for resolving this issue would be highly appreciated. Thanks in advance.
PS: I could share internet using the same USB modem with a machine running Windows 7 using similar method.Hi,
Refer to this tutorial:
How to share internet from Windows 8 computer via WiFi without using Router
http://gallery.technet.microsoft.com/How-to-share-internet-from-ab8d6d35
if this issue persists, try to see if there is newest network driver for windows 8.
Alex Zhao
TechNet Community Support -
Does a device need constant internet access when using Adobe products?
If a user wants to use photoshop on a device that is not 1)on an network 2) does not have internet access. Is this a problem when launching the program?
Hi CarolynHayden,
No. Your application are installed directly on your computer, so you won't need an ongoing Internet connection to use them on a daily basis.
An Internet connection is required the first time you install and license your desktop apps, but you can use the apps in offline mode with a valid software license.
Please let us know if this was helpful.
Regards -
WRT54G configuration for internet access using Lacie Network Space Max
Please HELP!!!!
I have tried for the past 2 weeks trying to configure my router WRT54G so it allows me to access the Lacie over the internet without luck. I have followed every instructions from Lacie and every other FAQs and help on the internet, still no luck. I have spent numerous days with Lacie tech support and they could not figure it out - why my router would not allow me access over the internet. I am hoping that the big guns here can help me.
I have a number of laptops connected wirelessly to my local network and every laptop can access the Lacie NAS hardwired to one of the ports on my router. My entire system works wonderful locally.
The Lacie has been assigned a static IP of 192.168.1.199
My local network has a starting IP of 192.168.1.150 and ends at 192.168.1.199
My router's IP is 192.168.1.99
I have assigned port forwarding for my Lacie (192.168.1.199) for ports
20, 21, 25, 80, and 443.
I have tried other setups but no help. Please help!!!
Happy New Year!!!
Solved!
Go to Solution.Scrooge... thanks!
My NAS has ftp enabled. Access to the network is excellent throughout my local network. Every PC, wirelessly, can access everything on the NAS without any problem. Even when using the web browser using the IP or the dyndns.org assigned to the NAS. (I signed up for a free dynDNS)
The NAS can be accessed throughout the local network using explorer (under the network directory) and also by mapping the drive. The NAS can also be access using the web browser by either through its assigned IP (192.168.1.199) or by using the NAS's dyndns.org web address (web access requires login since it accesses the Network Space Max web page) - both by http and/or by ftp
My problem is accessing it through the internet outside my local network, i.e. from my work place or any other place away from home. The ability to access my data away from home is what I really wanted to be able to do.
"Open the setup page of the router and go to Status tab. Note down the Internet IP address.
Open the Internet browser and in the address bar type http://Internet_IP_address:21 or ftp://Internet_IP_address .
See if that works for ftp server."
Using the router's IP address for both format, http and ftp - I am not getting connected, even in my local network. Using NAS's static IP 192.168.1.199, I am able to access only using the ftp format. http://192.168.1.199:21 does not take me anywhere, but without the :21 takes me to the login page.
Again, thanks for all your help.... I am lost and I need your HELP!
v/r,
abelts -
No Internet Access on Private Network
Hi,
I have an and ESXi Host with few VM's and i require Internet Access on these servers. This is Mini lab i have created at home.
I have My Home Broadband Router (192.168.0.1) acting as a DHCP server handing out DHCP addresses as usual.
A Cisco 3750 with 3 Vlans created with inter vlan working with the "Ip Routing" command.
A Physical PC
A ESXi Host
3 Vlans:
Vlan 100 10.0.9.1/24 (Home Vlan) Created DHCP Pool on this Vlan on 3750
Vlan 200 10.0.10.1/24 (Voice Vlan) Created DHCP Pool on this Vlan on 3750
Vlan 300 192.168.0.2/24 (Internet Vlan) DHCP handing out IP's from home broadband router (Uplink setup from Home ADSL router)
3750 Switch:
Port 1 ESXi Trunk
Port 2 Home PC (Vlan 100)
Port 3 – 28 Vlan 300 and all giving DHCP addresses from home ADSL router
Home PC (Vlan 100 – IP Address 10.0.9.52)
From Command Prompt PC can ping the following:
10.0.9.1 (Gateway) Ping Ok!!!!!
10.0.9.2 (ESX Host) Ping Ok!!!!!
10.0.10.1 (Gateway for Voice Vlan 200) Ping Ok!!!!!
192.168.0.2 (Gateway for Internet Vlan 300) Ping Ok!!!!!
192.168.0.1 (Home Router & DNS) No Ping…..
Cisco 3750 Switch
This can ping the following:
10.0.9.1 (Gateway) Ping Ok!!!!!
10.0.9.2 (ESX Host) Ping Ok!!!!!
10.0.10.1 (Gateway for Voice Vlan 200) Ping Ok!!!!!
192.168.0.2 (Gateway for Internet Vlan 300) Ping Ok!!!!!
192.168.0.1 (Sky router & DNS) Ping OK!!!!!
My assumtion is if i have these settings on my home PC:
IP Address 10.0.9.55
S/M 255.255.255.0
Gateway 10.0.9.1
DNS Server: 192.168.0.1 (Home Router)
i should get internet access on my 10.0.9.1/24 network.
IP routing is enabled and inter Vlan is working correctly. The issue I have is I have no internet connectivity on Vlan 100 (10.0.9.1/24) from my desktop PC or any of my VM's on the 10.0.9.1/24 network and internet seems to be working fine on any device in vlan 300.
I have added my Running Config an attachment to give you a better understanding.
Please can someone find i solution as i desperately require internet access on my VM's but they need to stay on the 10.x.x.x subet due to CUCM licensing.
Kind Regards
ZubairHi,
It sounds to me like the home router (192.168.0.1) doesnt have a route back to your 10.0.9.0/24 and 10.0.10.0/24 networks.
Can you try a source ping from your 3750 switch as follows
ping 192.168.0.1 source 10.0.9.1
If this fails you will need to add static routes on the home router for the above networks with a next-hop of your 3750 192.168.0.2 -
Why does it say no internet access when I connect my laptop to my personal hotspot IPhone 5S?
Every time I try to go on a webpage it says no internet access on the Internet bars
Hi, jon.baldauf.
These articles will help you troubleshoot the issue that you are experiencing when attempting to connect to the iTunes Store. Make sure after each troubleshooting steps to test the results.
iTunes for Windows: iTunes Store connection troubleshooting
http://support.apple.com/kb/ht1527
iTunes: Advanced iTunes Store troubleshooting
http://support.apple.com/kb/ts3297
There is a possibility that security software installed could be the cause of the issue. You may have to process the steps in this article.
iTunes: Troubleshooting security software issues
http://support.apple.com/kb/TS3125
Cheers,
Jason H. -
No internet access when "Send All Traffic" VPN Checked
Hi Ladies and Gents
Wonder if you can help me. These past few days I have been setting up a VPN on my DD-WRT enabled router. I have successfully accomplished such task, however when I'm connected to the VPN on my phone my public IP address does not change, after doing some reading I believe that is because "Send All Traffic" is unchecked in the VPN profile, but when I check "Send All Traffic" I get no internet access what so ever.
Any advice/input/solution to this would be greatly appreciated.
Cheers
CameronCammy1230 wrote:
when I'm connected to the VPN on my phone my public IP address does not
it's not supposed to. -
No internet access when i use my notebook into a router
I am trying to use my notebook as a repeater.
I enabled the MS Virtual WiFi Miniport Adapter and configured it with a SSID and password.
The connection seems to be alright, but when connecting my phone to this connection, I get no internet access (the phone is connected and receives an IP with no problem, but when trying to connect to the internet, as if there is no connection).
I am running windows 7I am trying to use my notebook as a repeater.
I enabled the MS Virtual WiFi Miniport Adapter and configured it with a SSID and password.
The connection seems to be alright, but when connecting my phone to this connection, I get no internet access (the phone is connected and receives an IP with no problem, but when trying to connect to the internet, as if there is no connection).
I am running windows 7
wifi repeaters are specialized and its cheaper and easier to get one on ebay, they are low cost and are popular to deal with dead spots with wifi both with business and homes alike
Corsair Carbide 300R with TX850V2
Asus M5A99FX PRO R2.0 CFX/SLI
AMD Phenom II 965 C3 Black Edition @ 4.0 GHz
G.SKILL RipjawsX DDR3-2133 8 GB
EVGA GTX 660 Ti FTW Signature 2 (GK104 Kepler)
Asus PA238QR IPS LED HDMI DP 1080p
ST2000DM001 & Windows 8.1 Professional x64
Microsoft Wireless Desktop 2000 & Wacom Bamboo CHT470M
Place your rig specifics into your signature like I have, makes it 100x easier to understand!
Hardcore Games Legendary is the Only Way to Play! -
IPad Internet access when WiFi and Cellular features are disabled
Local security policies require me to disable all wireless communications on devices operating within specific “Controlled Access” areas. Is there a specific lightning (cable) adapter I could use to connect an iPad device to a hardwired Ethernet cable (CAT-5 or 6) to facilitate wired internet communications in this situation? Alternately, can I use a standard Lightning-to-USB cable connected to a MacIntosh computer and somehow configure the MacIntosh to act as a router-like device for internet communications between the iPad and other intranet or internet endpoints that the MacIntosh is also able to interact with? Basically, I need to establish internet connectivity to/from the iPad without the use of wireless communications options, and I'm interested in the options I could pursue.
Thanks for the YouTube links bobseufert.
I'm going to try this approach out myself (just to verify that it works), but I'm really hoping that another - less encumbered, approach can be found for my end-goal. The larger-scale view of my need includes connecting multiple iPads (one per workstation area) to a local intranet. Since I can't use a WiFi or any other wireless communications solution for this installation, I might need a collection of adapter cables and powered USB hubs if I choose to implement the options detailed in these two videos on a large scale. Sure, that's all possible, but what I'm really hoping to find somewhere is an RJ-45 configured Ethernet-to-Lightning Adapter that will work with iOS devices.
From one perspective I can see why this type of adapter has not been built yet. However when you think about the wired adapter options that are available to connect the iPad/iPhone to a remote display (or overhead projector) - there is at least three different versions available through Apple, even through Apple sells wireless video display capabilities (I own two Apple TV devices myself), you wouldn't think that a wired network option for these mobile devices would be something out of the question...
BTW, I noted that Redpark (www.redpark.com) has some serial (RS-232) adapters for the older 30-pin iPads/iPhones and for the newer Lightning equipped iPads/iPhones that Apple has signed-off on. Redpark also has an RJ-45 to Lighting Adapter, but this particular implementation is built (i.e., wired) for the CISCO Console port, which is not compatible with your typical CAT-5 / CAT-6 wiring configuration.
If anyone else finds a Lightning Adapter providing both Ethernet-based Data (via an RJ-45 connector) and Power to keep the iPad devices charged (24/7) I would really like to hear about it... Thanks for your continued support! -
No Internet access when easy vpn tunnel is down.
Hi.
I have an error. i have a 819 router. with a Easy vpn tunnel.
And i am using the Identical Addressing feature, where i nat vlan1 over loopback0
I also have a vlan2 where i dont use identical addressing.
I have the Easy vpn tunnel configured on loopback0 and vlan2
from Vlan1 i nat to looopback0 with
ip nat inside source static Network 192.168.250.0 192.168.5.0 /24
and i nat outside with
ip nat inside source list INET interface GigabitEhternet0 Overload
ip access-list extended INET
permit ip 192.168.5.0 0.0.0.255 any
When tunnel is up, there is internet from vlan1, vlan2 and loopback0
But when the tunnel is Down, i can only get internet from Vlan2 and loopback0
The route for the tunnel is 0.0.0.0, i need all data to go to the vpn when its up. and to the internet when its Down.
Any ideas?
Thanks.That is correct.
Config.
controller Cellular 0
no cdp run
track 1 ip sla 1 reachability
default-state up
ip tcp synwait-time 10
ip ftp source-interface Vlan1
ip ssh rsa keypair-name Router.yourdomain.com
crypto ipsec client ezvpn VPN-Cel
connect auto
group VPN key -key-
mode network-extension
peer 12.12.12.12
virtual-interface 1
username RouterCel password Password
xauth userid mode local
crypto ipsec client ezvpn VPN-Eth
connect auto
group PANTst key -key-
backup VPN-Cel track 1
mode network-extension
peer 12.12.12.12
virtual-interface 1
username Router password Password
xauth userid mode local
interface Loopback0
ip address 192.168.6.1 255.255.255.0
no ip redirects
no ip unreachables
no ip proxy-arp
ip flow ingress
ip virtual-reassembly in
crypto ipsec client ezvpn VPN-Cel inside
crypto ipsec client ezvpn VPN-Eth inside
interface Cellular0
ip address negotiated
no ip redirects
no ip unreachables
no ip proxy-arp
ip flow ingress
ip nat outside
ip inspect CCP_LOW out
ip virtual-reassembly in
ip verify unicast reverse-path
encapsulation slip
load-interval 30
dialer in-band
dialer idle-timeout 0
dialer string hspa-R7
dialer-group 1
no peer default ip address
async mode interactive
crypto ipsec client ezvpn VPN-Cel
interface FastEthernet0
no ip address
interface FastEthernet1
switchport access vlan 2
no ip address
interface FastEthernet2
no ip address
interface FastEthernet3
no ip address
interface GigabitEthernet0
ip dhcp client route track 1
ip address dhcp
no ip redirects
no ip unreachables
no ip proxy-arp
ip flow ingress
ip nat outside
ip inspect CCP_LOW out
ip virtual-reassembly in
duplex auto
speed auto
crypto ipsec client ezvpn VPN-Eth
interface Serial0
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
shutdown
clock rate 2000000
interface Virtual-Template1 type tunnel
no ip address
ip nat outside
ip virtual-reassembly in
tunnel mode ipsec ipv4
interface Vlan1
ip address 192.168.250.1 255.255.255.0
no ip redirects
no ip unreachables
no ip proxy-arp
ip flow ingress
ip nat inside
ip virtual-reassembly in
ip tcp adjust-mss 1452
no autostate
interface Vlan2
ip address 192.168.16.1 255.255.255.0
no ip redirects
no ip unreachables
no ip proxy-arp
ip flow ingress
ip nat inside
ip virtual-reassembly in
ip tcp adjust-mss 1452
no autostate
crypto ipsec client ezvpn VPN-Cel inside
crypto ipsec client ezvpn VPN-Eth inside
interface Dialer2
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
ip flow ingress
ip local policy route-map myRoutes
ip forward-protocol nd
ip http server
ip http access-class 23
ip http authentication local
ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
ip nat inside source list INTERNET interface GigabitEthernet0 overload
ip nat inside source static network 192.168.250.0 192.168.6.0 /24
ip route 0.0.0.0 0.0.0.0 Cellular0 254
ip route 8.8.4.4 255.255.255.255 Cellular0
ip access-list extended INTERNET
permit ip 192.168.6.0 0.0.0.255 any
permit ip 192.168.16.0 0.0.0.255 any
ip sla auto discovery
ip sla 1
icmp-echo 8.8.8.8 source-interface GigabitEthernet0
ip sla schedule 1 life forever start-time now
dialer-list 1 protocol ip list 1
dialer-list 2 protocol ip permit
route-map myRoutes permit 10
match ip address 101
set ip next-hop dynamic dhcp
access-list 1 permit any
access-list 23 permit 12.12.12.12
access-list 23 permit 192.168.0.0 0.0.255.255
access-list 101 permit icmp any host 8.8.8.8 echo
control-plane -
Why do I not have internet access when my phone says it's on LTE?
I am currently having internet connectivity issues. My phone will say it's on LTE, but when I try to use an app that requires internet connectivity, it says that I need to check my internet connection. I can't refresh facebook, check e-mails, or send iMessages. When I join a Wifi network, everything works as it should. I've tried doing a soft reset on my phone multiple times by holding the home and sleep button down until the phone reboots. I've also restored network settings, but nothing seems to be helping. Just wondering if anyone had any tips before I had to take it into the Verizon store.
meganweers,
I am sorry you are having these issues with accessing the internet on your device. Thank you for all the troubleshooting you have done thus far. Have you tried to remove and reinsert the SIM? http://vz.to/1irq2bL Are you able to send text messages and use voice just fine? Are there others reporting the same issues with data connection?
LindseyT_VZW
Follow us on Twitter @VZWSupport -
Internet Access with a Networking Card
I have a macbook pro (for about three months) that has VISTA installed. ( I have been a PC user for about 20 years and will need time to learn about the MAC operating system). I bought a Verizon USB720 card to access the internet nationally through VISTA on the macbook pro. There may be some software in the computer that prevents my being able to use this card. The error message in effect says that someone is using this internet connection. I returned the first Verizon card and bought another card with the same error message. Any ideas what the problem may be? Many thanks EKL1
You probably need to set the card up in OSX. Verizon should have a modem script that needs to be installed. (Hard Drive>Library>Modem Scripts). Then you need to set up the card from Network Preferences. Then it should work on both platforms.
Maybe you are looking for
-
Remove Item from Item list through DTW
Hi Experts, Please do the needful for the below issues. 1.System is not allow partial delivery but I already activate allow partial delivery at sales order logistic tab. 2.System is allow to print the document at client place automatically at the t
-
I unable logon to application after upgrade to 11.1.1.2
Hi, I have problem to logon to HFM application after upgrade from 9.3.1 version to 11.1.1.2. The application is "Classic Application". I upgraded SharedServices(HSS), Planning, AnaliticServices, Workspace and HFM. Everything is OK. I can logon to all
-
What is the table name from which......
Hi, when i run a report KE30 - Execute Profitability Report through TCode KE30 in r/3 ( profatibility analysis and profitibility report ) from which table does the report pics the data. Is the report generation in r/3 is thorugh ABAP only ? thanks in
-
I want to truncate a long type data into 100 characters during the retrieving. how can I do that in select statement?
-
data in recordset is from two tables is this a valid statement?: if (isset($row['table1.education']) != "") { $query .= " WHERE table1.desiredcountry LIKE '{$row['table2.desiredcountry']}'";