No Internet access without replugging WAN to Linksys EA2700

Every time after the router (Linksys EA2700) is powered off and restarted, there is no interent access available. The router configuration status reports an Internet Address of 0.0.0.0 and all the devices at home are left with a wifi without Internet access. I have to unplug the WAN from the router and plug it in again while it is turned on to restore internet access (and a normal Internet Address is seen from the status page). The WAN works fine with the routers I had previously. I wonder if I have to perform this every time I power on the router. Do you have any suggestions? I have tried resetting the router and reinstalling Cisco Connect but that didn't work.

It would be best to isolate the concern by connecting a computer to the modem. Observe the performance of the modem’s internet connection within 24 hour. If there is nothing wrong with the modem’s performance then you now need to deal with the router. Make sure that the router’s firmware has been updated then reset the router after a firmware upgrade. If you have determined that the problem is really with the router then you might need to return the router and have it replaced.

Similar Messages

Repair Internet Access without Hard Reset (E72)

I just came back from a trip. I used many different Wifi-hotspots during my journey, which kept accumulating in the internet settings. So I deleted all the new hotspots from my Nokia E72 phone. Unfortunately, this action messed up the internet access completely.
I already did a reset of the settings with +#7780#, but to no avail. I have SmartConnect 1.3.6 installed. Deleting and reinstalling did not change anything.
In detail:
I cannot change the access point for the built-in browser any more. When I select it, nothing happens. Before the reset it had now connection at all, now it is fixed to my mobile network providers internet access point (GPRS/3G).
In internet settings (Menu -> Ctrl. Panel-> Settings-> Connection -> Destinations) there is now an empty destination group without a name, and it can not be deleted.
Certain functions in internet settings do not work any more, like copying an access point to another group. The destination settings often will hang and cannot be closed any more. A restart is needed.
Some applications (e.g. Podcasting) still show some of the deleted access points.
Almost all other applications which do not have their own access point management (like. fring) will not connect anymore.
My question:
Is there any other way of accessing and/or deleting these settings (maybe directly in the system) besides doing a hard reset (*#7370#) requiring a (PC-based) backup?
If I ever want to travel only with my E72 I would need a solution to these problems on the phone itself.
Thanks.
E72-1, product code 0586718, firmware 022.007

@hadimassa: as I wrote in my post, SC has nothing to do with my problem. Installing SC doesn't improve stability in general and maybe one of the causes in the first place, but this was not the point here. Too late, so to say
The internet access parameters must be stored somewhere on the C: drive. I am interested in the exact location.
E72-1, product code 0586718, firmware 022.007

Can I use a WTR54G for satelitte internet access

I am having wildblue satelitte internet installed.the install tech said I could use linksys wireless g to hook up two computers for internet access.I have bought the linksys equipment and was reading on the web site that it wont work with satelitte internet.has anyone done this please help

vickers57,
I've been using wildblue satellite with a WRT54Gv5 for 18 months now. It will operate in the DHCP mode, which is the default. I would reset the WRT54G to factory settings by unplugging the power adapter, hold in reset button on rear, then plug in while you hold for 10 seconds, then release.
Run a standard Ethernet patch cable (straight-thru,not crossover) from wildblue modem to 'Uplink' port on WRT54G, then another standard Ethernet patch cable from your pc to one of the 4 ports on the WRT54G. Set your pc Ethernet port to 'obtain IP automatically'.
Power cycle (remove power plug, wait 10 seconds, then plug in) the wildblue modem, when it's 'up' and the top 2 lights are solid not flashing (power and receive), then power cycle the WRT54G. Lastly, if your pc is win98 or winME then reboot it, otherwise XP should get the new IP address from the router OK without rebooting. If not, reboot your pc.
To view the WRT54G configuration, lauch your browser, type in http://192.168.1.1 in the URL bar and hit 'enter'. The default username is 'default' and the password is 'admin'. Click on the far right on 'Status'. If all is good you should see the wildblue modem's IP address and wildblue's DNS.
Let me know how it goes!
tonyruck

E3000 - Guest access without password

Hi,
I just installed a new E3000 wireless router and it works fine.
But i'd like to give my guests Internet access without having to enter a password.
I know how to change the -guest password but it requires a 4 digit minimum password.
Is there a way to remove it ?
Thanks
Solved!
Go to Solution.

No. There's no way you can remove it. The least you can do is to make the password simpler like 1234 or something.

WRT54GS Internet Access Restriction Policies

I am finding it challenging to correctly define Internet Access Restriction
policies on my Linksys WRT54GSv4 wireless router. Documentation does not
describe multiple policies being enabled. I think that multiple policies
should be from most restrictive to least, but I am not sure.
I wish to deny Internet access from my child's WII and PSP from 10:30 PM to
6:30 AM. Also, I want to filter all hosts for blocked words and blocked
sites.
Currently, I have three policies:
1) Child_Evening --
WII and PSP MAC Filter
10:30 PM to 11:55 PM
Deny
2) Child_Night --
WII and PSP MAC Filter
12:00 AM to 6:30 AM
Deny
3) SiteWord --
IP Range 192.168.1.2 - 254
Block Various Sites
Block Various Words
I would like input as to the correct use of multiple Internet Access
Restriction policies

create an Internet Access Policy:1. Internet access Policy - 1
2. Enable.
3. Child Access(Name of the policy)
4. Deny range 192.169.1.252
5. 10:30 PM to 11:55 PM - Everyday
6. Blocked Services - All
7. Port Range Start - 1 ; End - 61000
8.Save Settings
9.Rebooting....
You deny all access through by all services to any sites.
Create the same policy with different number and name to deny access from 12:00 AM to 6:300 AM..
Url Filtering Policy to deny adult sites, they're too much with different url address.You can deny most of them,but not all.
Good Luck!!!!!
Message Edited by gochev_george on 03-16-200702:47 AM
Message Edited by gochev_george on 03-16-200702:54 AM
Thanks
Kind Regards
ing.George Gochev
DSL and Telecommunications Engineer

Linksys E1000 cannot ping gateway unless I unplug/replug WAN

I have been using this router for the last six months and never had a single problem. Then yesterday out of nowhere internet stopped working and I was not able ping my ISP gateway (both wired and wireless) [Received: Destination host not reachable on both Windows Vista / 7]. Rebooted the router but still no luck. Unplugged / Replugged the net connection from the WAN port and then finally ping was successful.
Now the weird this is every time I power on the router the Internet does not work and ISP Gateway seems not reachable, but if I unplug/replug the WAN connection the ping reply starts and internet works without any problem.
I have updated the firmware to the latest version (2.1.02 build 5May 6, 2011), disabled SPI firewall and tried changing the MTU value but still no luck.
Another unusual thing I have noticed is that during the router boot up the WAN port LED blinks a lot faster than usual. After I unplug/replug the wan connection the blinking rate seems to be normal.

My ISP Gateway uses a completely different IP address 172.16.x.x, while my router has the default IP setup 192.168.1.1. The thing is I am able to ping the router IP, but not the ISP Gateway IP unless I unplug/replug WAN.
I googled around quite a bit yesterday and found that others have also had similar problem.
http://homecommunity.cisco.com/t5/Wireless-Routers/Power-Outage-Linksys-E1000-router-lights-blinking...

How can I use Airport Express to create a standalone Wi-Fi network without Internet Access so I can browse web pages on the local network? I will be using MAMP as my server (Apache)

I would like to create my own Wi-Fi standalone network at an upcoming tradeshow where there will be NO internet access.
Currently, I run and develop sites on my iMac use MAMP to manage my sites locally. Using MAMP, I run my sites as though they are on the internet although everything is local.
I purchased an Airport Express hoping I could create a standalone network so that the iMac would broadcast its website to whatever device connects to it such as my iPhone, iPad and MacBookPro.
However, after setting up the network successfully (I have a green light on the Airport Express, and there is NO internet going through it), I am not able to go any further by logging into the iMac's websites from the other machines. Form my MacBookPro Finder, I can look at files and folders using afp://10.0.1.2, from the Find/Go/Connect to Server utility, but I can't browse the website that is running on the iMac via the Safari browser.
Can anyone help me configure my MacBookPro (or iPad, or iPhone) to run the website on the iMac when they are all on the same network?
Thanks so much!!

1) connecting the TC using a ethernet cable from one of the two modem's LAN ports to the TC's WAN port
2) create a new Wi-Fi network using the TC ?
Does someone already create a new Wi-Fi network using its TC connected by Ethernet on a modem/router device ? How do you set up the DHCP (and NAT) ? Which range did you use ?
This is easy enough to do..
Plug the TC directly into a computer.. without other connections to do the setup.
Using the newly installed 5.6 utility.
Bridge the TC.
Create a wireless network.
This is an older screen shot and I would set security to WPA2 Personal only not WPA/WPA2 Personal as shown above.
I do recommend you use wireless names that are short, no spaces, pure alphanumeric.
Update the TC..
Now plug it into the modem router.. it will be a part of the network without doing NAT and DHCP itself.. which you do not want.. that leads to double NAT issues.. but it is a WAP that provides access to devices on both 2.4ghz and 5ghz bands directly to the main router.

Problems in Internet access in the middle being a modem and Linksys RV016

Good afternoon, I have another problem with Cisco Linksys RV016 Router, the router used to connect to ADSL Internet 3 links which these in turn give direct service to a server right now each of them, the idea is to connect the 3 modems LAN router and connect the server, this is no problem so far. The point is that here at my work people access to Remote Access Servers for Windows and VNC TightVNC or my servers with Linux (ask why not login at TeamViewer or LogMeIn, but it is another matter), the idea is to leave as they are, that everything is apparent and improve systems with load balancing (Router). The modem has ports open for remote access the 3389, are accessed without nigun problem, but when connecting the router and can not, I opened the same ports in Router and name and works.
Servers handle the no-ip.org for access and name resolution on DNS and so with that name assigned by the no-ip is where remote access from the Internet.
I do not know if you understand, but I hope someone help me with this.
In advance thank you very much and greetings.

Look, the first phase of my work to be done is to try a single server and it has Windows Server 2008, you explain:
1. This ADSL modem connected directly to a single server (Windows).
2. It is accessed without any problem by remotely from another network and / or from the Internet via remote access.
3. The modem has port 3389 open to allow remote access from another network or Internet (up to here is my current scheme and there is no problem).
4. Connect between the modem and Linksys RV016 router server.
5. I open the same ports with the modem for remote access.
6. If I have Internet server.
7. Remote access is not working.
As time??? something can be done to solve this problem. The server as you mentioned earlier is running as a service no-ip.org for publication DNS name and not have to be constantly changing the IP by automatic changes made by the supplier (eg server name and for which so is taken from the internet: servidorwin.no-ip-org).
See if you explain me better.
Thanks in advance and greetings.

RV042 Windows incompatibility HTTP Connections between Subnets without Internet access

Hello,
We are a company of the banking sector
We have two RV042 Router.
One of this Router (R1) is configured for restrict users without internet access. This router doesn´t internet connections, the Wan ports are blocked.
Router 1: restricted users
Router 1 IP Lan: 10.22.4.1/24
Router 1 IP Subnet 1: 10.22.1.2/24 (For communication with Web Servers on Lan 10.22.1.0/24)
Pc1: 10.22.4.3/24
DNS: 10.22.4.51/24 (This DNS Server have an Internet connection through subnet 2)
The other router (R2) has an internet connection through the wan port for the access of the DNS Servers for respond to request of clients, and a web server in this subnet
Router 2: Web Server´s LAN and Internet Connection for the DNS Server
Router 2 IP Lan: 10.22.1.1/24
Router 2 IP Subnet 2: 10.22.4.2/24 (For communication with restricted user on Lan 10.22.4.0/24)
Web Server: 10.22.1.60/24
We need to access the web server from the network restricted users.
From Linux Operating System, the access to web server its ok
But, from Windows Operating Systems, we can´t access to web server. Time Out
So, we think that there are some incompatibility between the Router RV042 and the windows operating systems
On the website of microsoft, there is an article regarding an incompatibility issue with the RV042 which could help
http://support.microsoft.com/kb/934430
we copied a file attachment.
Thanks, sorry for bad English

Hi,
Have you also tested configuring static route?
I am asking that, because RV042 does not support VLANs and following that cannot do inter-VLAN routing. Configuring subnet with Multiple Subnet option is only giving access to this subnet to internet. Unless a static route is not configured as where this traffic to be routed in the LAN, the router itself normally will drop the packet.
If it works for you, this leads me to the thought that there is other routes that packets from LAN 10.22.1.0 to LAN 10.22.4.2 (and vice versa) are taking, but not necessarily the routers.
Here I can just give a direction of where to look, but if you think you checked all possibilities, it would be better to contact the support line. They will help as long as the device is under warranty.
Hereby the contacts:
http://www.cisco.com/c/en/us/support/web/tsd-cisco-small-business-support-center-contacts.html
Regards,
Kremena

Movie not loaded without internet access

We have developed a flash movie to industry showing production data for a machine. Clients running this flash movie in a web browser. Some of these clients have internet access and others do not.
The clients have access to intrernet shows flash movie without problems.
The clients without internet access just shows a black box with the text note loeaded movie.
The customer does not want to connect these clients to intenet but would consider opening specific ports or websites if necessary.
What is it that requires flash player from internet to download flash movies?
Flash movie connects to a server over XML socket to exchange production data. Serve respond to requests for policy-file-request with <cross-domain-policy> <allow-access-from domain='*' to-ports='*'/> </ cross-domain-policy> \ 0th
It does not matter which version of the flash player or internet explorer that we use. We have tested many different varieties.
Hoping for help!

What errors are you getting when connecting to the server? There's several events you should be listening for, e.g. Event.CONNECT, Event.CLOSE, DataEvent.DATA, IOErrorEvent.IO_ERROR, SecurityErrorEvent.SECURITY_ERROR, etc..
One of those should be giving you some useful information about the connection status.
What sandbox are you using? Here's some info on setting the sandbox to essentially Administrator level so the SWF is allowed to connect to all resource types via a config file:
http://help.adobe.com/en_US/ActionScript/3.0_ProgrammingAS3/WS5b3ccc516d4fbf351e63e3d118a9 b90204-7c95.html
If not running AIR (which removes the need for that config) you're going to want your SWF to have access to local filesystem and networking without restriction. You should check what Security.sandboxType is set to. If the config file is successful (or you use the SWF settings menu to add the SWF as trusted) it should report Security.LOCAL_TRUSTED. If it's AIR it will report Security.APPLICATION. Then you know the SWF has permission to access network.
Outside that the events returned from the socket connect should let you know if the problem lies on the server. I'm assuming you're already running a Security.allowDomain("*"). I don't know if this pertains to LAN IP ranges however, that'd be a good question. It falls in WAN in the 192.168.x.x and 10.0.0.x ranges.

How can I transfer all of my music library from my iTunes library on my PC to my iPhone without Internet connection will filesharing for home sharing allow me to access my iTunes library from my iPhone if I do not have Internet access on my PC

How can I transfer music from my home PC in my iTunes library to my iPhone for without Internet access will home sharing allow me to access my iTunes library from my iPhone 4 without Internet

Why don't you just sync it to your phone?

For OS X: Whenever I have internet access my disk is running continuously for a period of time without any activity on my part. When I close internet access the disk activity stops. Who is fishing for data?

For OS X v5 or 6: Whenever I have internet access my disk is running continuously for a period of time without any activity on my part. When I close internet access the disk activity stops. Who is fishing for data?

Thanks for your reply. I don't use itunes so that couldn't be it. Reading about Little Snitch and Hands Off, however, educated me about the data harvesting in many apps and that when buying from the AppStore one will more likely get Apps with benign data harvesting.

I'm connected to the wifi at home but no internet access. i was surfing on the same wifi without any problems. and also this issue is for other wifi network.

hello everyone.
i was surfing browsing and downloading on my iphone 4 on my home wifi and other places without any problem but today i found out that even though i'm connected to my wifi i got no internet access. i also got this new problem, my led flash is on. if i tilt the device the flas dims a bit. i tried switching off the device but still the flash is on. i tried using at other wifi network same problem. i tried forget this network, switching off and turning on the device i also tried reseting the network and also hard reseting the device. but still same problem. what can i do about this? and if i send it to apple what are my options? i got warrant coverage so will they be able to repair it ? if they are not able to repair then will they give me new iphone 4 or refurbished iphone 4 for replacement?

Apple does not repair devices. If they are covered under warranty, the device is replaced. You will not get a new phone, you will get a service unit which is as good as if not better than new.
If all the basic troubleshooting from the User's Guide has been done and the device does not get Internet access via Wi-Fi from multiple locations, the only thing left is to take it to Apple.

I live in an area with poor data reception. Will the Maps app work without internet access?

I live in an area with poor data reception. Will the Maps app work without internet access?

Google Maps
Type in 'Ok maps' (no quotes) in the search and press enter
It will download the map area shown on the screen for offline use

Install and use Adobe Digital Editions on a computer without internet access ?

Hello,
I have a pair of PCs, one of them, with Windows Vista, has never been connected to the internet since many years. It is used for word processing mostly. I didn't even bother to plug an ethernet cable inside or think about a Wifi USB key, in a way it's better that way, no useless distractions and no security threats.
I want to use that offline PC for work, and it would require to use Adobe Digital Editions on that machine. I downloaded the offline standalone installer from adobe.com without problems, however, apparently, Adobe only accepts us to use the program after we have activated it through internet access.
Does that mean there is simply no way out, and I can't use Digital Editions on my offline computer ?
Would you perhaps know a solution to this issue ?
Thank you VERY MUCH if you can help !
Kind regards

I don't think there is a way out.
You could use it for non-DRM books without authorizing, but there are much better options (such as the free Calibre) for that anyway. http://calibre-ebook.com/
If you make a temporary internet connection, then once authorized, you should not need internet access to read books you have got elsewhere and copied to it.

No Internet access without replugging WAN to Linksys EA2700

Similar Messages

Maybe you are looking for