No Internet: DHCP works, but no IP.

I don't know what exactly caused it, but this was within the recent few weeks.
Symptom: No IP address, even though DHCP (dhclient and dhcpcd) works perfectly. After invoking dhcpcd and obtaining an IP, ifconfig still shows nothing.
I don't know if it matters, but I have two NICs, and it doesn't matter which one I connect to, it's the same thing.
I can confirm that this is not my network's problem, since the same machine with a dual-booted Windows works.
I can also confirm that this is definitely a recent upgrade, not some mis-config issue (unless a default config is causing this). I thought I borked my machine completely, so I reinstalled Arch entirely. Network is fine, until I did a full system upgrade. Then the same thing happened again.
This is so weird. I'd appreciate any help!

lsusb returns nothing but my keyboard/mouse
lspci | grep net
00:19.0 Ethernet controller: Intel Corporation 82566DC-2 Gigabit Network Connection (rev 02) # on-board NIC
07:01.0 Ethernet controller: 3Com Corporation 3c905B 100BaseTX [Cyclone] (rev 30) # pci NIC
I even took out the PCI card, rebooted, same thing.
And since I have no internet on the broken computer, I'll just type out what's relevant here. Let me know if you want more.
eth1 is on-board intel card, and eth0 is the PCI card.
dmesg | grep eth
eth1: (PCI Express: 2.5GB/s:Width x1) <mac here>
eth1: Intel(R) Pro/2000 Network Connection
eth1: MAAC: 7, PHY:6, PBA No: ffffff-0ff
eth0: setting half-duplex.
eth1 NIC link is Up 10 mbps half duplex, flow control : none
eth1: autonegotiated half duplex but link partner cannot autoneg. Try forcingfull duplex if link gets many collisions.
eth1: 110/100 speed: disabling TSO
eth1: changing MTU from 1500 to 576
eth1: changing MTU from 576 to 1500
<repeat the above 5 lines 7 times>
That's about it. Any ideas what might be wrong? Thanks.

Similar Messages

My iPad cannot connect to my internet. the internet is working but not with my ipad.

my iPad cannot connect to my internet. the internet is working but not with my ipad.

Call your ISP (Internet Service Provider) and explain them your issue, it could range from having your router configured incorrectly to having a wiring issue. Personally, I have Comcast and they are great, no issues, and awesome customer service.
Hope you get up and running ASAP

In a cafe, all internet connecti9ns work, but the email client is saying Timed Out, can't access the server. Rebooted. Problem persists.

All other internet connections work - but the Mozilla email client can't access the mail... Works in every other café. But not here. Thanks!

I'd suggest you check with the cafe owner which ports are allowed there.
If in doubt simply use webmail, which will most likely work.

HT3964 Hi , My modem got zapped by lightning yesterday. My iMac still was able to power on when I tried it yesterday. Today the modem is replaced and internet is working, but now the computer will not power on. I followed the steps to reset SMC. Noth

Hi , My modem got zapped by lightning yesterday. My iMac still was able to power on when I tried it yesterday. Today the modem is replaced and internet is working, but now the computer will not power on. I followed the steps to reset SMC. Nothing. ??

Ouch, not much more you can do, I think you'll have to have it looked at.

Can see and recognize my wireless network and Internet is working, but I can't connect with ANY computers/iPad/iPod/air TV, etc. I have reset the time machine several times, and can see the network, but cannot access it with any device. PLEASE HELP!

I have Comcast Internet and have it connected to a Motorla Surfboard modem and have that running directly to a 2TB Time Capsule. The TC is serving as our time machine as well as our wireless router. We lost power in a storm a week ago and can no longer connect to my wireless network I can see the network and sign into it via password, but cannot connect with any device(iMac, MacBook, iPhones, iPod touches, air tv, etc.). ALL of these devices worked gat before the power went out. I reset both modem and TC and still can't connect. I can connect to the Internet through Ethernet cord directly from the modems dn have confirmation(per Comcast service) that the Internet is working and we have a good connection.
The TC is less than six months old so I'm not sure what is wrong. I have reset settings with TC to no avail. I have reset the TC SEVERAL times and have no idea what could be wrong and what is prohibiting me from connecting. Anyone that has ANY suggestions or ideas as to how to fix this, PLEASE HELP!!! I'm going crazy using iPad 3G and not being able to connect to our wifi. THANKS FOR YOUR TIME AND I LOOK FORWARD TO GETTING BACK TO THE 21ST CENTURY!

Anyone have any ideas or information to help with this? Any help and consideration is MUCH appreciated.

Internet sharing works but the DNS part doesn't

I'm posting this message because I believe it is a bit different from other 'Lion internet sharing' posts in terms of the source of sharing and also the results I get.
Similar to other users experiencing the same problem, my internet sharing setup stopped working as expected after upgrading to Lion. However, I can't say it stopped working completely. It still does work but the DNS part doesn't. This means I can still perform pings, ssh and socket connections from computers using the shared connection. But I cannot browse the internet because web site names can't be resolved.
For example, my MacPro has two Ethernet interfaces. On one of them (en0) I vpn when connecting to work using a VPN service I created via System Preferences => Network. I used to share that VPN connection to computers using the 2nd one (en1). The other computers are linked to (en1) through a multiport hub. This setup used to work flawlessly in Snow Leopard and multiple users could use the shared vpn internet connection.
After the upgrade to Lion I can still see other computers on the local network and also ping any external internet site. I can even use Safari and navigate my ISP's home page using its IP address only. However, DNS doesn't work and internet domains cannot be resolved by name so internet browsing is not possible.
Furthermore, when I don't VPN to work but simply share the connection to the internet from (en0) to computers using (en1) everything works as it used to in Snow Leopard. The difference here is that the same DNS servers are used by both network services.
So far I'm stuck with these findings and I don't know where else to look for answers. Any input or feedback is greatly appreciated.

I've to admit that i don't even know what VPN means.. but..
I have an 27" iMac (mid 2010), a iPhone 4 and a Macbook Pro 13" (mid 2009) .. and i used to share my ethernet connection to wi-fi on Snow Leopard. Since i upgraded to Lion (i'm using it since the first DP, and i think the internet sharing was working under the 1st DP .. i'm not pretty sure), it just doesn't work.
Just like solongpc, it does activate the internet sharing, my other devices can see and connect but neither of then (my iMac - host or my mbp and iphone) can navigate on the internet. And when i turn off my internet sharing (on my iMac), it still not acessing any website.. and i've to restart my moden.

HT201299 Verizon signal is strong but get error message "Ipad is not connected to the Internet"   Wireless works but my Verizon account does not

Verizon signal is strong but get error message "Ipad is not connected to the Internet"   When I try to use Safari.
Wireless works but my Verizon account does not

Some things to try first:
1. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
2. Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
3. Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
4. Go into your router security settings and change from WEP to WPA with AES.
5. Renew IP Address: (especially if you are droping internet connection)
    •    Launch Settings app
    •    Tap on Wi-Fi
    •    Tap on the blue arrow of the Wi-Fi network that you connect to from the list
    •    In the window that opens, tap on the Renew Lease button
6. Potential Quick Fixes When Your iPad Won’t Connect to Your Wifi Network
http://ipadinsight.com/ipad-tips-tricks/potential-quick-fixes-when-your-ipad-won t-connect-to-your-wifi-network/
~~~~~~~~~~~~~~~~~~~~~~~~~
Wi-Fi Fix for iOS 6
https://discussions.apple.com/thread/4823738?tstart=240
iOS 6 Wifi Problems/Fixes
How To: Workaround iPad Wi-Fi Issues
http://www.theipadfan.com/workaround-ipad-wifi-issues/
Another Fix For iOS 6 WiFi Problems
http://tabletcrunch.com/2012/10/27/fix-ios-6-wifi-problems-ssid/
Wifi Doesn't Connect After Waking From Sleep - Sometimes increasing screen brightness prevents the failure to reconnect after waking from sleep. According to Apple, “If brightness is at lowest level, increase it by moving the slider to the right and set auto brightness to off.”
Fix For iOS 6 WiFi Problems?
http://tabletcrunch.com/2012/09/27/fix-ios-6-wifi-problems/
Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
http://gizmodo.com/5944761/does-ios-6-have-a-wi+fi-bug
How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
http://www.iphonehacks.com/2012/09/fix-wi-fi-connectivity-issue-after-upgrading- to-ios-6.html
iOS 6 iPad 3 wi-fi "connection fix" for netgear router
http://www.youtube.com/watch?v=XsWS4ha-dn0
Apple's iOS 6 Wi-Fi problems
http://www.zdnet.com/apples-ios-6-wi-fi-problems-linger-on-7000004799/
~~~~~~~~~~~~~~~~~~~~~~~
How to Boost Your Wi-Fi Signal
http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Boost-Your-Wi-Fi-Signal.h tm
Troubleshooting a Weak Wi-Fi Signal
http://ipad.about.com/od/iPad_Troubleshooting/a/Troubleshooting-A-Weak-Wi-Fi-Sig nal.htm
How to Fix a Poor Wi-Fi Signal on Your iPad
http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Fix-A-Poor-Wi-Fi-Signal-O n-Your-iPad.htm
iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
WiFi Connecting/Troubleshooting http://www.apple.com/support/ipad/wifi/
How to Fix: My iPad Won't Connect to WiFi
http://ipad.about.com/od/iPad_Troubleshooting/ss/How-To-Fix-My-Ipad-Wont-Connect -To-Wi-Fi.htm
iOS: Connecting to the Internet http://support.apple.com/kb/HT1695
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Connect iPad to Wi-Fi (with troubleshooting info)
http://thehowto.wikidot.com/wifi-connect-ipad
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
How To Fix iPhone, iPad, iPod Touch Wi-Fi Connectivity Issue http://tinyurl.com/7nvxbmz
Unable to Connect After iOS Update - saw this solution on another post.
https://discussions.apple.com/thread/4010130
Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
~~~~~~~~~~~~~~~
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
 Cheers, Tom

HT204023 hi there can any one help me i have a iphone 5 but my mobile internet not working but i can connect to my wifi no bother

hi there can any one help me i have a iphone 5 but my mobile data is not working but a can connect to my wifi no bother

talk to your carrier about the data subscription and possible settings changes to their apn than

WLAN Controller Stops DHCP working but....

We serve 2 VLANs from the controller and it seems to shut down DHCP traffic for one of the 2 VLANs. Has anyone seen this or any ideas why? We have to reboot the device to get DHCP working again.
NOTE: Its only setup to pass DCHP requests through to our DHCP server.

try Disabling DHCP proxy and try once... Controller >> Advanced >> DHCP >> Proxy >> Disable (Uncheck) >> Apply >> Try connecting.
Regards
Surendra

Internet is working but router is not

Hi... I just changed yesterday from Road Runner Cable internet to a local company that services my community called "EnTouch Systems." The internet works fine when I plug directly from the wall to the computer (modem that does the phone and internet is mounted in master closet now and runs through the walls and out outlets) but when I attempt to set up my Linksys WRTP54G (Linksys+Vonage from when we had Vonage) it does not work. When I run the setup CD it came with it gets all of the way to the end then I get a pop up saying there is no internet and to unplug my modem for 60 seconds which I then do but it accomplishes nothing. Can anyone help? *****NOTES***** I have read all of the suggestions on the forum like change the local IP and clone the mac address... i have reset both the modem and the router, tried new ethernets... nothing works. please help!

Well try upgrading the firmware of the router & keep on holding tightly
the reset button in such a way that power light is blinking on the
router & then do a complete network power cycle i.e., unplug the power
cables from the modem & from the router & then plug in the power cable
to the modem first once all the lights are solid green you could plug
in the power cable to the router & check out it will definately work!!
Configuration for cable connection:-
Access the setup page of the router by launching an
Browser and type on the address bar, 192.168.1.1 and press enter. When
it prompts for the username and password, leave the username field
empty and provide password as "admin" (Without quotes)
click on ok.
On the main setup page the ""Internet Connection Type"" should be
on ""Obtain IP Automatically - DHCP ?. Click on the Save Settings
button.
Now click on the sub tab ""MAC address clone"".
- Click on enable
Click Clone & click save settings
Check WAN Ip on Status page of router ....
If getting Valid Ip .... try going online
If not ... power cycle for 4-5 minutes & then agian check the WAN Ip address .....

Airport Express: Internet Access Works But Not "Seen" in Admin. Util. ??

Hi All --
I have a friend with the set-up described below and a seemingly impossible problem. he's asked for my help, and so I'm asking for yours, because frankly the situation just has me stumped. Here goes:
Set-Up & Other Relevant Facts
• DSL connection comes out of the phone jack and goes to a Westell model 6100 modem.
• From there, a short Ethernet cable goes to a Linksys 5-Port Workgroup Switch.
• Two Ethernet cables exit the Linksys Switch: one goes to a PC, and one goes to an Airport Express (AX).
• From the AX, a USB cable goes to a printer (a Brother 1440 laser printer).
• The AX is only about 10 feet from his PowerBook G4 15-inch and he gets a full (four-bar) signal on Airport menulet at the top of the screen.
• When he first set-up his system, the G4 and the Airport did set up the Brother printer (using the Airport Setup Assistant), and the Brother is listed as a printer on the G4's printer window or such.
• Both the G4 and the PC access the web fine via this setup (the G4 wirelessly). In System Preferences > Network, the Airport Network is listed, and it says "Airport is connected to the network Apple Network 6c6c1. You are connected to the Internet via Airport."
Problems
• When the Airport Admin Utility is opened, no Airport Express appears at all, even when "rescan" is repeatedly clicked.
How can this be? How can the PowerBook be connecting wirelessly to the Web through the Airport Express, but the Airport Express no be "seen" by the Airport Admin utility?
• In addition, although web surfing is possible for both PowerBook and PC, neither computer is able to successfully print to the Brother 1440. When he tried printing from the PC, he got the following error messages:
[Status for LPT1]
Result=(02)The printer on this port is not responding.
Status Line=BUSY:H,ACK:H,PE:H,SLCT:H,FALT:H,SLIN:L,HBSY:H,INIT:H,STB:H
Later, it seemed that printing from either computer would start and then stall, flashing a variety of different signals about spooling or "printer busy" and the like, all of which appeared to indicate things just weren't working right..
Anyway, the initial questions we're dealing with are the ones in bold above. The printer issues are probably are related and they can be addressed secondarily.
Any and all help with this will be greatly appreciated. Thanks everyone.
-- JDee

Thanks for your reply- just to re focus my problem- I
have no issue with getting a wireless network "green
light"
Which is the cable modem correctly giving the Express an IP from your ISP's DHCP pool of numbers.
- my issue is I can't stream itunes or get a
usb printer to work off the xpress USB port.
I have checked everything as my posts explain- The
reason I have been looking at this thread is I have
never been able to see the airport in a "scan" per
JDee post.
That is odd and doesn't happen on my wireless network!
Nor have I read in any post that an extra
ip address is necessary
All routers have at least two IP's - an external and an internal. When the router acts as an internal DHCP server it hands out many more IP's. Your Express gets one external IP and the default internal one is set to 10.0.1.1 and the first IP handed out is 10.0.1.2, etc.
However I have seen different subnets- from dncp
server.
Are you talking about the external IP's that your ISP is randomly assigning without your control? Are you talking about the different ways you can configure the internal DHCP numbers? If not there's something else going on. Everything on Douglas internal network should have an IP from the Express DHCP server vs. JDee's internal IP's should all be assigned by the modem/router DHCP server. Once you have everything on the same network numbers AirTunes, printers, and Airport Admin Utility lists just work!
Hey look I really appreciate your help here in
anyway- I'm really stumped. I want to stream music
really bad... and just don't see why it won't work-
its drving me crazy...
I enjoy a good challenge, especially when they are solvable. After trying all the possible software and connection possibilities there's always the chance it's been a hardware failure all along
What IP number does your computer have and what number does the Express have? If it's a router it has two IP's!

Access to a site from the Internet not working, but is for other sites on the same SP

Greetings,
My environment:
SP 2013 Enterprise w/ SP1 installed
2 servers in the farm, 1 for SQL, 1 for SP
Both servers are VMs running on Hyper-V, SQL is a bit underpowered when it comes to memory, SP is fine
5 web applications running, including a MySites web app and Central Admin (I've seen where separate web apps isn't the recommended configuration any more, but, this is how it was done when setup)
All sites run using SSL (443), same NIC, using host headers, pretty standard stuff (I think)
Claims authentication on all but Central Admin
Central Admin is firewalled off to all but a select few
1 to 1 correspondence between web apps and content databases
Other than MySites, all sites have either 1 or 2 site collections (search is in a separate site collection on 2 of the sites); MySites has many more site collections
So, site A, site B, site C, and site M are all supposed to be available from the Internet (with SSL and authentication) and also from the internal network. For site A, C, and M, this is true, no problem. Site B however doesn't work when coming in from the
Internet, just internally. I've received multiple reports of this from some of my users around the country, and I've been able to replicate it on my computers.
IIS just gives a blank page, no messages, no login. Chrome does present a login box, and will log into the site and work. This is from a laptop that is a part of our domain with cached credentials, but not directly connected to our network or using
our VPN. A non-domain laptop without cached credentials prompts me to login, as it should, and seems to work. The domain laptop will use the cached credentials to auto-authenticate to A, C, and M, but not B.
I'm using IE 11. I've tried putting the site into Compatibility mode, no joy. I've added the site to the Trusted Sites list, no joy. I don't have IE 10 available for testing (or 9 or 8 or ... just 11 :-( ) I've flushed the browser cache, emptied the
cookies, etc.
So, 3 of 4 sites work fine on the same machine, same Internet connection, same browser, same SP. I'm thinking it's something with IE, but, what? Seems like IE should be sending the same creds to all the sites, as they're all in the same Internet domain.
Does IE or Windows cache different creds somewhere? Or is there something in SP? I could see where one person's settings could get hosed somehow, but numerous people around the country with different h/w, different Internet connections, different credentials?
ARGH! HELP!!! Point me at something to look at, because I'm drawing a blank (and getting permanent dents in my forehead from banging it on my keyboard)...
Thanks much,
Steven

It seems that the difference between the sites that will open and the one that won't is the Default Authentication provider is set to NTLM on those that open, and Negotiate (Kerberos) on the one that won't. The Authentication Provider for the Default zone
is Claims Based Authentication on all the sites, just site B (which won't open) is set to Negotiate (Kerberos), the others are set to NTLM.
Short term: can I change the provider to NTLM without destroying the site?
Long term: point me in the direction for setting up Kerberos correctly on my server/farm, as from what I can tell Kerberos is the recommended path forward. I'll setup a non-production test site and get it figured out.
Thanks much.
Steven

Internet is working but browsers will not load.

About a week ago my web browsers stopped working. I'm running Vista and I use FireFox. I also have Internet Explorer but neither of them will load any web page when i go to them. I know my connection is working because I can use any other program that requires internet. I've been told that I have a virus. I've ran Malwarebytes, RKill, Avast!, CCleaner, Advanced System Care, and I've tried a system restore but nothing has helped. Anyone have any idea whats wrong or how I can fix this?

I have the same problem as the poster for this thread. A couple days ago my web browsers stopped working. I was watching a live stream on TwitchTv (I watched through my Firefox browser) and Firefox had been pestering me with notifications to upgrade to version 27.0.1. After I concluded watching on Twitch I finally gave in and upgraded FireFox. It prompted me that the change would be in effect after a restart I shutdown my computer (and turned back on) instead of restarting it. When I tried to use Firefox, it wouldn't let me and said the quote below. Both Firefox and IE say the same thing: Unable to connect:-The site could be temporarily unavailable or too busy, try again in a few moments.-If you are unable to load any pages, please check your computer's network connection.-If your computer is or network is protected by a firewall or proxy, make sure that Firefox is permitted to access the web. I'm running Vista and I use FireFox. I also have Internet Explorer and Google Chrome but neither of them will load any web page when i go to them. I know my connection is working because I can use any other program that requires internet. I tried system restore, but for some reason the computer said it failed. I've checked all the connections and cables, rebooted my router and modem, ran Malwarebytes and AVG 2012 with updated content and I've tried a system restore but nothing has helped. I also followed your steps: Command Prompt and select 'Run as Administrator'. Enter the command listed below seperately and hit return after each one. ipconfig /flushdnsnbtstat -Rnbtstat -RRnetsh int reset resetlog.txt
netsh int ip resetnetsh winsock reset(But netsh int reset resetlog.txt and netsh int ip reset did not work) Anyone have any idea whats wrong or how I can fix this?

Internet stops working but air tunes keep going

Hey there, first post on the board. Usually I can find the problem but this time I can't.
I have a D-link wbr-2310 wireless router and got myself the new airport express N 3 weeks ago.
The first week everything was fine and all of a sudden my internet was on and off. My airpot signal is always full but the pages keep looking for connection.
The weird thing is, Air tunes keeps going good at the same time.
The only solution so far is to turn off and then turn on the airport connection from my macbook but doing this every 10 minutes isn't the solution.
Did someone experience the same problem?
I don't know much about network but it looks like my airport express is taking the connection away from the router.
Thanks to you guys.

I will try going back to WEP.
I found a solution for my internet to keep working now.
Letting my Airport Utility open keeps me online...
The Airport Express does not disappear anymore.
But I need to let the Utility open...
If I close the program......Bang! No internet, no Express.
This is really weird.

Wga54g wont work with new 1200 router..internet never works but there's a connection

I've tried so many settings I cant even remember where i left off but one general question will help me troubleshoot to the next step.
sometimes the connection shows 'acquring address' but never connects. i've fiddled with things so that i can get the GA to acquire an address but the internet comes through. Also the GA never shows up on the client table.
So is the fact that i can get a network address a good thing or doesnt that necessarily mean i'm 'connected' to the network. Its frustrating to have the G light lite up yet no connection
also at one point i did get the GA to show up in the client table when it was directly connected to the 1200 but when i walked into the room and attached it to the PC, no dice
i've turned off all firewalls temporarily and the 1200 is set on wpa/wp2 mixed. when i tried setting it just to wpa i got a warning then i lost my interenet. i had to reinstall the 1200 again
other misc details in no particular order..just things i've tried
setting MAC and and IP just for the GA.. did 192.168.1.112...did a reservation from the 1200 setup screen
sometimes the 1.250 browswer access to the GA turns off, for instance when i change it to automatically DHCP or when i set the IP to 1.112 i lose the ability to get into the setup.
ive tried setting up the IP in the TCP settings of the connection as 192.168.1.112 but is the gateway necessary? i've tried what i believe to be correct gateways of 192.168.254.1 and 192. 168. 254 254 with no success.
when i do have success getting into the GA setup screen and things say 'connected', i still dont have the internet, just the green light on the adapter.
i have this on infrastructure

First of all try the following steps in the E1200:
A] With the help of Cisco Connect Software (if at all you have installed the router with the help of this software)
1] Open the software and go to the option which says "Router Settings"
2] Then click on the option which says "Advanced Settings" which will take you to the router's configuration page.
3] Then Click on wireless Tab select Channel Width to 20 MHz only and Channel to 6, 9, and 11. Click Save Settings....
B] If you haven't installed Cisco Connect then you can log on to the router's user interface using it's default IP address in the browser which is 192.168.1.1 and type in 'admin' as the password leaving the username field blank. This will take you to the router's web interface and then follow steps as mentioned above to make the changes.
Second the gaming adapter will only show up in the DHCP client table when it is connected directly to the router, other wise it will not appear. Since the gaming adapter has a fixed ip address – 192.168.1.250
Third you have to lower down the Wireless Security level to WEP as this gaming adapter can only accept WEP security...
Here is the link if you’re encountering difficulties connecting the Wireless-G Game adapter to a wireless network: http://www6.nohold.net/Cisco2/ukp.aspx?pid=93&login=1&vw=1&app=search&articleid=4543&userrole=Linksy...

No Internet: DHCP works, but no IP.

Similar Messages

Maybe you are looking for