No internet either wired or wireless

Hi,
DSL modem works fine when connected directly to computer. No internet output from WRT54G wired or wireless, but wireless network is recognized by computer, just no internet.  I did a reset and installed the latest firmware, then I ran thru the setup CD that came withe the router, and the internet test said no internet connection was available.  Cables are fine, connector innards look clean.  Any suggestions?  Thank you.

First of all do the following connectivity:
QUICK TIPS:
The router’s power adapter needs to be plugged to your router and into an available power outlet.
If using a wired connection, the first Ethernet cable needs to be plugged to the computer’s LAN port into any of the router’s blue numbered Ethernet ports.
The second Ethernet cable should be plugged to the modem’s Internet port and the other end into the router’s yellow Internet port.
Ensure that you have no firewall enabled that may prevent the router from being detected.
After making the physical connectivity do the following settings according to the ISP setup. Here is the link for setting up a Linksys router with DSL Internet service: http://www6.nohold.net/Cisco2/ukp.aspx?vw=1&docid=20ee1457387f40178cd5f41d4b585db4_3687.xml&pid=80&r...

Similar Messages

  • Do all the computers on a home sharing network have to be either wired or wireless?

    Trying to allow the following to use home sharing:
    Mac mini 2012 (wired and wireless)
    MBP 13" 2011 (wireless only)
    MBP 15" 2012 (wireless only)
    Apple TV 2013 (latest update)
    All computers running Yosemite 10.10.1 and iTunes 12.0.1.26
    iTunes on the Mini can see both of other shared libraries on the MBPs
    iTunes on the MBPs can see each other's shared libraries but not that on the Mini.

    Hello!
    So the issue is with Mac Mini's ability to transmit it's Home Sharing around.
    Change the Mac Mini's computername is System Preferences > Sharing. Restart your Mac Mini via  > restart.
    After restarting, make sure Home Sharing is still enabled in the Mac Mini's iTunes. Did that solve it?
    If not, continue.
    we trash the /sc info/ folder using the Terminal command below:
    Open a Terminal window - for example by searching for the word terminal via Spotlight (the magnifying glass in the top right corner of your computer display) - and copy-paste the line below (to prevent typing mistakes):
        sudo rm -Ri /Users/Shared/SC\ Info/
    Enter your password after pressing return. Note that your will not see that you're typing, so no stars or dots like: *** You'll have to enter the password blindly and press return once you’re finished.
    After doing this, restart your computer, open iTunes and authorize one last time.
    For your education, so you know what we’re doing: this /sc info/ folder stores your authorizations. So deleting the folder and restarting the Mac will force a fresh version to be created. This fresh version will not have any of the errors or corruptions which are probably causing this issue.
    Issue solved?

  • Sharing the dial-up connection of a PC laptop--either wired, or wirelessly

    Hello, fellow Mac users! I just got my first Mac--a beautiful 1.83 GHz MacBook. I LOVE the switch to OS X from Windows XP.
    Anyway, here's problem:
    I am leaving on vacation, and, unfortunately the resort at which we are staying does not have Internet Access, so I am forced to use dial-up. Unfortunately, since I have heard very bad reports about the Apple USB Modem, I can't get a modem for the MacBook itself, so I will use my PC laptop's modem. The PC Laptop is a Windows XP Pro machine. So, here's the problem--try as I might, I just cannot get the darn PC laptop to share its dial-up connection; either over a ethernet cross-over cable, or adhoc Wi-Fi.
    So, please help me get this to work, or I will be forced to use a PC laptop to check e-mail, RSS feeds, and anything else online.
    Thanks in advance! (And thanks, Steve Jobs, for helping to create some of the best computers out there!)

    Here is from the help support on xp :
    Configure,a dial-up
    connection, click the connection that you want to
    configure, and then, under Network Tasks, click Change
    settings of this connection.
    Do one or more of the following:
    To configure dialing devices that your computer uses
    to make a connection (a modem, for example), phone
    numbers, host addresses, country or region codes, or
    dialing rules, click the General tab.
    To configure dialing and redialing options, or X.25
    settings, click the Options tab.
    To configure identity authentication, which is a way
    to help verify your computer’s identity when making a
    connection, data encryption (which codes the content
    so that it’s less likely to be readable by someone
    other than the intended recipient), or terminal window
    and scripting options, click the Security tab.
    To configure the remote access server that you want to
    connect to and protocols (the format that your
    computer uses to communicate with other computers)
    used for this connection, click the Networking tab.
    To turn Internet Connection Sharing on or off or
    configure your computer to establish a dial-up
    connection automatically, click the Advanced tab.
    When you run the
    Network Setup Wizard and enable Internet Connection
    Sharing, some protocols, services, interfaces, and
    routes are configured automatically. The following
    table describes these configured items.
    Configured item Action
    IP address 192.168.0.1 Configured with a subnet mask
    of 255.255.255.0 on the LAN adapter that is connected
    to the home or small office network.
    Autodial feature Enabled.
    Static default IP route Created when the dial-up
    connection is established.
    Internet Connection Sharing service Started.
    DHCP allocator Enabled with the default range of
    192.168.0.1 and a subnet mask of 255.255.255.0. Unique
    addresses in the range 192.168.0.2 to 192.168.0.254
    are allocated to private network clients.
    So try to use dhcp on your network setting or something between those range listed above with a cross over cable (make sure the cross over cable has good connection).

  • Satellite L735 won't connect to the internet (both wired and wireless)

    Hi,
    I have a brand new Satellite L735, and I'm having a lot of trouble with the internet connections.
    When I connect it to a wireless network it finds the profile and connects to it but then still says "no internet access" for both IPv4 qnd IPv6 connectivity statuses.
    I have tried troubleshooting, turing off the computer and wireless network and back on, but it's stil not working.
    The same happens with the workplace wireless, despite other computers connecting to it fine (so it doesn't come from the networks). I've also tried connecting it at work with an ethernet cable but no luck.
    I have the Atheros AR9002WB-1NG Wireless network adapter and the Atheros AR8152/8158 PCI-E Fast ethernet controller.
    I'm not sure what to do as the laptop is new and so it shouldn't need updates, all the settings are default, etc. I'd very much appreciate any help on this!

    Hi
    Uninstall or disable the TCP/IPv6 and use only the TCP/IPv4 protocol.
    Furthermore check if in TCP/IPv4 properties the IP address and other settings are set to assign automatically
    Furthermore I would recommend checking the firewall and some security applications which could be preinstalled on the notebook.
    It could be possible that antivirus or firewall prevent the notebook from connecting to internet.

  • WRT320N Router fails to assign an IP in either wired or wireless configuration

    Hi 
    I bought a Links WRT320N   router less the 6 months ago. I have been using it  as a wireless router since without any problems.
    A week ago  one of the PC's in the networks did not receive a valid IP, although it was able to connect to the router
    it happened to one PC only out of 4 we a using on the net.   The machine got a default windows ip in the 169.  Domain.
    Strangely enough the problem went away after a day and then re-asserted itself two days later.
    Today  all of the PC connected to the router failed to get a valid IPs,  I connected one of the PC's  with an Ethernet cable but still was not able to get a valid IP.
    Replacing the router with an older wireless router I had laying around  enabled all the machines to connect
    what could be the problem with the WRT320N?

    Connect one computer to the router with the Ethernet cable. Press and hold the reset button on the router for 30 seconds. Release the reset button and wait for 10 seconds. Power cycle the router and restart the computer.
    Now check the IP address on the computer. If you have the valid IP address of 192.168.1.xxx and default gateway 192.168.1.1 then try to open the setup page of the router. If you are able to open the setup of the router then try to reconfigure the router.
    If you are not getting the valid IP address on the computer then assign a static IP address on the computer. Go to Local area connection properties. Click on internet protocol TCP/IP properties and select ' use the following IP address'. Change the IP address to 192.168.1.10, subnet mask to 255.255.255.0 and default gateway to 192.168.1.1. Try to ping the router IP address.
    If you get replies from the router IP address then open the setup page of the router and reconfigure the router.

  • Can not access internet via wired connection, wireless working OK

    Background information,Came home from vacation turned on PC to access email.Emails started downloading then stoped,started getting messages that firefox stopped working and Thunderbird quit working and others.My desktop is attached to a verizon router.all my other devices are wireless and are working fine through the same router.I connected my laptop to the lan connection, turned off wifi and accessed the internet via lan connection.Using device manager, checked drivers, says up to date, also says that it is working properly.I have gone to the command line and can ping google.com.I can ping the loop around. ping127.0.0.1I have done the ipconfig/release,ipconfig/renew, and ipconfig/flushdnsipconfig/all indcates that it is there and enabledMy Lan connection is part of the mother board.can not access internet via wiredconnection.Not sure what to do next.Help Please   

    Reply: I spent about an hour last night doing all the things that you suggested including moving the lan cable from my desktop to my laptop which worked fine. When I hoover over the connection it says;  Network3                                                                                        Internet Access   no error messages.When I unplug the cable at the router a red x covers that connection icon.Plug it back in red x goes away.It is seeing the router, just does not appear to be providing selected web page info.Computer thinks it is working fine.

  • [SOLVED) No network with either wired or wireless

    My network on my Arch laptop seems to be not working. It was intermittent yesterday and now doesn't work at all. The router works both wirelessly and plugged in - tested with another (windows 7) computer. The intermittent problem was present on two different ISPs as well, so I am pretty sure it is not a service issue at the ISP end.
    The networkmanager applet indicates that the router is connected. I tried a few things from this forum to no avail, and always reverted any changes so it seems that I did not do anything out of the ordinary. I tried to do a -Syu update but it failed mid-way due not being able to access the mirrors.
    How can I check whether this is hardware or software settings problem?
    Last edited by raavas (2012-05-21 17:55:24)

    Ok, we're back in business. The USB works again.
    Here is the report of ip addr:
    1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 scope host lo
    inet6 ::1/128 scope host
    valid_lft forever preferred_lft forever
    2: eth0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN qlen 1000
    link/ether 88:ae:1d:9a:11:cf brd ff:ff:ff:ff:ff:ff
    3: wlan0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP qlen 1000
    link/ether 70:f1:a1:d8:b6:2a brd ff:ff:ff:ff:ff:ff
    inet 192.168.1.2/24 brd 192.168.1.255 scope global wlan0
    inet6 fe80::72f1:a1ff:fed8:b62a/64 scope link
    valid_lft forever preferred_lft forever
    and here is lspci -nn
    00:00.0 Host bridge [0600]: Advanced Micro Devices [AMD] RS880 Host Bridge [1022:9601]
    00:02.0 PCI bridge [0604]: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (ext gfx port 0) [1022:9603]
    00:04.0 PCI bridge [0604]: Advanced Micro Devices [AMD] RS780/RS880 PCI to PCI bridge (PCIE port 0) [1022:9604]
    00:05.0 PCI bridge [0604]: Advanced Micro Devices [AMD] RS780/RS880 PCI to PCI bridge (PCIE port 1) [1022:9605]
    00:11.0 SATA controller [0106]: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 SATA Controller [AHCI mode] [1002:4391]
    00:12.0 USB controller [0c03]: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB OHCI0 Controller [1002:4397]
    00:12.2 USB controller [0c03]: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB EHCI Controller [1002:4396]
    00:13.0 USB controller [0c03]: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB OHCI0 Controller [1002:4397]
    00:13.2 USB controller [0c03]: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB EHCI Controller [1002:4396]
    00:14.0 SMBus [0c05]: Advanced Micro Devices [AMD] nee ATI SBx00 SMBus Controller [1002:4385] (rev 41)
    00:14.1 IDE interface [0101]: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 IDE Controller [1002:439c] (rev 40)
    00:14.2 Audio device [0403]: Advanced Micro Devices [AMD] nee ATI SBx00 Azalia (Intel HDA) [1002:4383] (rev 40)
    00:14.3 ISA bridge [0601]: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 LPC host controller [1002:439d] (rev 40)
    00:14.4 PCI bridge [0604]: Advanced Micro Devices [AMD] nee ATI SBx00 PCI to PCI Bridge [1002:4384] (rev 40)
    00:14.5 USB controller [0c03]: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB OHCI2 Controller [1002:4399]
    00:18.0 Host bridge [0600]: Advanced Micro Devices [AMD] Family 10h Processor HyperTransport Configuration [1022:1200]
    00:18.1 Host bridge [0600]: Advanced Micro Devices [AMD] Family 10h Processor Address Map [1022:1201]
    00:18.2 Host bridge [0600]: Advanced Micro Devices [AMD] Family 10h Processor DRAM Controller [1022:1202]
    00:18.3 Host bridge [0600]: Advanced Micro Devices [AMD] Family 10h Processor Miscellaneous Control [1022:1203]
    00:18.4 Host bridge [0600]: Advanced Micro Devices [AMD] Family 10h Processor Link Control [1022:1204]
    01:00.0 VGA compatible controller [0300]: Advanced Micro Devices [AMD] nee ATI Madison [Radeon HD 5000M Series] [1002:68c1]
    01:00.1 Audio device [0403]: Advanced Micro Devices [AMD] nee ATI Redwood HDMI Audio [Radeon HD 5000 Series] [1002:aa60]
    02:00.0 Ethernet controller [0200]: Broadcom Corporation NetLink BCM57780 Gigabit Ethernet PCIe [14e4:1692] (rev 01)
    08:00.0 Network controller [0280]: Atheros Communications Inc. AR928X Wireless Network Adapter (PCI-Express) [168c:002a] (rev 01)
    How can I proceed?

  • Lenovo G510 Laptop Windows 7 64 bit - no wired or wireless access.

    I recently bought a Lenovo G510 laptop and installed windows 7 64 bit onto it. After the install, I had to install all of the drivers, and everything was working fine.
    Today I opened my laptop after having closed it ten minutes earlier, only to find that it wouldn't wake up from sleep mode. After trying everything I could think of, I did a hard restart and chose the 'start windows normally' option. However, when Windows started back up, it no longer recognized any internet sources, wired or wireless.
    Windows troubleshooter says I need to 'turn on wireless capability'. I don't see a wireless hardware switch anywhere on the laptop. fn+f5 does nothing. No other keys look like they control internet. The device manager says all of the network devices are working normally. I tried reinstalling the drivers, but that didn't do anything either. The Windows Mobility Center says that the wireless is turned off, but the 'turn wireless on' button is greyed out and is not able to be clicked.
    I'm all out of ideas. Anyone have any suggestions?

    Hi nej,
    thanks for posting and welcome to the community. As you may already know when it comes to wireless issue there are many factors that can cause that different factors to look at. However in your case I would suggest you to click on "Start" and in the search field type "Services.msc". Click on services and once the services window opens, search for "WLAN AutoConfig". Doulble lick on it and check if the service is started or not? If it is not, ensure that it is started.
    Hope this helps.
    Regards

  • Windows XP failing to acquire network address whether wired or wireless

    Hi guys,
    I initially asked this question elsewhere because it was happening in OSX as well, though now that the OSX side of things has been fixed it is purely a Windows XP problem, and is a different problem to the one in Mac OSX.
    The problem seems simple enough, in that Windows XP just refuses to acquire a network address when connecting to the internet whether wired or wirelessly. I spent the best part of 7 hours on this on Monday, and after trawling through countless web pages I seemed to establish that there was an error with the AFD Driver (which, as I understand, is one of three required for the DHCP Client service to run). I was on the verge of probably doing something monumentally stupid and trying to repair/replace that driver when in a moment of genius (which should have arrived significantly sooner in the day) I asked my fiancee when the last time was that she could remember the internet working properly. She said it was the day before just after she agreed to install SP3, but the installation failed. So I used System Restore and rolled the system back to before that point, et voila. Everything was fine.
    Not appreciating the path taken to fix her iMac, my fiancee then tried to install SP3 again and the same problem reoccurred. Another System Restore fixed it. The problem now is that on startup Windows XP seems to revert back to the same state, and will refuse to acquire an IP address. A System Restore back to the same time will fix it. However, whilst this takes little longer than an actual startup, I was wondering whether or not anybody had any bright ideas for a permanent fix to this problem.
    All ideas, solutions and pearls of wisdom welcomes with open arms.

    Crazy Jamie wrote:
    Hi guys,
    I initially asked this question elsewhere because it was happening in OSX as well, though now that the OSX side of things has been fixed it is purely a Windows XP problem, and is a different problem to the one in Mac OSX.
    The problem seems simple enough, in that Windows XP just refuses to acquire a network address when connecting to the internet whether wired or wirelessly. I spent the best part of 7 hours on this on Monday, and after trawling through countless web pages I seemed to establish that there was an error with the AFD Driver (which, as I understand, is one of three required for the DHCP Client service to run). I was on the verge of probably doing something monumentally stupid and trying to repair/replace that driver when in a moment of genius (which should have arrived significantly sooner in the day) I asked my fiancee when the last time was that she could remember the internet working properly. She said it was the day before just after she agreed to install SP3, but the installation failed. So I used System Restore and rolled the system back to before that point, et voila. Everything was fine.
    Not appreciating the path taken to fix her iMac, my fiancee then tried to install SP3 again and the same problem reoccurred. Another System Restore fixed it. The problem now is that on startup Windows XP seems to revert back to the same state, and will refuse to acquire an IP address. A System Restore back to the same time will fix it. However, whilst this takes little longer than an actual startup, I was wondering whether or not anybody had any bright ideas for a permanent fix to this problem.
    All ideas, solutions and pearls of wisdom welcomes with open arms.
    Try using a system that is able to connect to the internet in Windows. Then go to http://www.microsoft.com/downloads/en/details.aspx?FamilyID=2FCDE6CE-B5FB-4488-8 C50-FE22559D164E and then download SP3 to the hard drive of that system. Then using the CD/DVD burning of your choice that you have for Windows burn the disc image file to CD/DVD and then insert it to the system that has the issue and upgrade it to SP3 that way.
    I used to use Windows update to get service pack, but one time it did not download and install correctly on an HP system. Since then I have went to Microsoft and downloaded the Service Pack and when it said that it installed successfully I deleted the file I downloaded. I never had issues when I get them and install them that way. The only Service Pack I had issues with was Service Pack 1 for Windows 7. I downloaded it from Microsoft to the hard drive and after it said it was installed successfully I deleted the file. I used it for a while then I shut the system completely down. Then when I booted into Windows I went to put in my password and nothing happened. I tried moving the mouse nothing happened. Then I did a hard reset, booted into Mac OS X, used Boot Cap Assistant, removed the partition, downgraded to Windows XP 32-bit and now miss all the features that come with 64-bit Operating Systems. I am now able to use 2.5GB of RAM out of the 8GB that is in my system. I thought with Windows 32-bit that 4GB what the most that could be used.

  • WLC Wired and Wireless Guests

    I am using WCS 6.0.132.0 and WLC 6.0.188.0.  I am creating guest ID's using the LobbyAmbassador interface, and I would like to allow guest users to use the same ID password either wired or wireless.  I cannot see any way to accomplish this, am I missing something?  If I use an external Radius server, would that allow me to do it?  If I do add a Radius server, do the ID's created in Lobby Ambassador 'flow' to the radius server, or do I need to use the new server interface (whatever it may be) to create them?  I know it is a lot of questions, but I am dealing with a few hundred guest users a week, and I am trying to avoid a lot of extra work for staff and inconveience for guests.

    If you are using lobby admin to create username and passwords, then you would be creating this on a WLC, either on a foreign or anchor controller.  Username and password can be used on either, since the WLC DB has all the info.  No need to have a radius unless you do not want to use the lobby admin feature and have your internal IT staff create username/passwords in AD or the local radius DB if it has one.  If the username will be used concurrently, then make sure Max Concurrent Logins for a user name is set to the # of concurrent users.

  • "wired AND wireless" or is it "wired OR wireless"? using a C309a

    I am setting up a C309a (also called a photosmart premium all in one) for a school.  I got the wireless to work.  That is, all is setup and I can print from a laptop using only a wireless connection.  The school has a few desktop computers without wireless capability.  Can I use the ethernet wired connection for those with in order to print from those desktops without losing my wireless capability on the laptops?

    To be a little more specific, the HP Photosmart C309A can support either a LAN (wired) or a Wi-Fi (wireless) connection to the access-point or wireless-router.  It does not support a LAN and Wi-Fi connection simultaneously.  In fact, connecting the LAN cable to the printer disables the wireless connection.
    It sounds like you've connected the C309A to the network wirelessly and that's fine.
    As to whether the laptops and desktops are connected to the network via LAN or Wi-Fi, it doesn't matter to the printer.  From the printer's point of view, it's just one network.
    There's one more combination to talk about:  you can connect to the C309A a single computer via USB while it's also connected to the network (either wired or wirelessly).
    So at the risk of confusing everyone, you can connect some HP Inkjet printers "Wired (USB) and Wirelessly (Wi-Fi)" or "Wired (LAN) OR  Wirelessly (Wi-Fi)". 
    Regards / Jim B / Wireless Enthusiasts
    ( While I'm an embedded wireless systems engineer at work, on this forum I do not represent my former employer, Hewlett-Packard, or my current employer, Microsoft )
    + Click the White Kudos star on the left as a way to say "thank you" for helpful posts.

  • I have qualitynet either wired internet. I buy a card good for a month at a time, I can only log into one device at any one time.  Are there settings I can adjust on my airport express to allow all my devices to connect to wi-fi without having to log out.

    I have qualitynet either wired internet. I buy a card good for a month at a time, I can only log into one device at any one time.  Are there settings I can adjust on my airport express to allow all my devices to connect to wi-fi without having to log out of one devise before using another?

    Some Internet providers that limit access to a single device at a time do so by the device's hardware MAC address. If your ISP is one of those, you may be able to substitute the MAC address of your AirPort Express base station for the computer. I would suggest that you contact them to find out if this is allowable.

  • I have a Time Capsule as my router.  I can connect wirelessly to the network and internet with my MBPr, but my Mac Mini will only connect to the network wired or wirelessly. Airport on it sees the internet as green, but will not connect.

    I have the Time Capsule hooked to a wireless modem.  It uses a static IP, which is put in and running.  The MBPr connects, as well as my iPhone 5, to the internet and network without problem.  I can see the Mac Mini, external drive attached to it, and the Time Capsule.  The Mac Mini connects to the network wired or wirelessly, but not to the internet.  On wireless, using AirPort the Internet shows green, but no connection when I open Safari.  The settings under network settings are identical except for LAN IP between the Mac Mini and the MBPr.  I was hoping someone might have an idea of what was going on.  Before I moved the Time Capsule was on Bridge mode from another router, now it is on DHCP and NAT for the internal network.

    No, its is connected direct to the providers fiber box.

  • Network drivers no internet wired or wireless

    I have a T60 type 2007 and model BE6. I recently have been unable to use my wired or wireless internet on my laptop. I thought it might be a problem with my drivers then. I tried uninstalling them and rolling them back but whenever I click uninstall or rollback driver the window freezes then.
    I tried updating my driver then to the latest ones which I got from the website for my wireless and network, and when I updated the drivers it would just keep on going in that window and eventually freeze, and then after I close it, the driver details showed it to be the new driver even though it froze. With the new drivers installed the local area connection would be disabled, and when I try to enable it, it would say connection failed.
    When I tried to rollback the drivers it would freeze, but after I opened it up again it would show my old driver information. With the old drivers, my local area connection would be enabled, but still when I try to connect to internet, it says the specified destination is not reachable. Also when I try disabling the wireless or local area connection it doesnt do anything, and when i do repair it freezes.
    Also for the drivers when i try to go into the resource tab, that window just freezes.
    I do not know if my drivers are updating correctly or not, because it freezes and such. Any help is greatly appreciated.
    thanks.

    Hi mishink7,
    Welcome to the Lenovo forum 
    Because you are having networking problems with both wired and wireless, it seems likely that the problems are caused not by the network device drivers, but by something higher in the network "stack". Did you install or update a firewall, Access Connections, or any other software just before you started having network problems?
    Best regards,
    Frank
    Results of Your Ideal Business-Class Laptop survey, concluded 2009-07-29.
    Did someone help you?
    Say thanks! with a kudo.
    Even better: Pay it forward, help someone else.

  • Thinkpad- T61 - Not able to connect to Internet either by cable or Wireless

    Hi Friends
    I'm having a T61 Thinkpad and yesterday i had tried system restore, but it has not done any changes,
    But then, I'm not able to connect to Internet either by cable or by Wireless.
    When i pressed Thinkvantage, i could see the Hardware wireless is on "OFF" status and I'm not able to turn it ON
    Can anyboby help me on fixing this issue and enable connect to INTERNET
    Thanks in advance
    Regards
    Sasi

    Hi,
    can you provide a bit more detail, as can you use the 3G network to access the web, and what security is your wireless using?
    Regards
    Ryan

Maybe you are looking for