No Internet IP address 169

Can't get the internet on my 27" iMac. WiFi has self-assigned IP address 169.254.88.203
How can I get a Internet Friendly IP address assigned?

Hi, this has worked for a few...
Make a New Location, Using network locations in Mac OS X ...
http://support.apple.com/kb/HT2712
10.7 & 10.8…
System Preferences>Network, top of window>Locations>Edit Locations, little plus icon, give it a name.
10.5.x/10.6.x/10.7.x instructions...
System Preferences>Network, click on the little gear at the bottom next to the + & - icons, (unlock lock first if locked), choose Set Service Order.
The interface that connects to the Internet should be dragged to the top of the list.
10.4 instructions...
Is that Interface dragged to the top of Network>Show:>Network Port Configurations.
If using Wifi/Airport...
Instead of joining your Network from the list, click the WiFi icon at the top, and click join other network. Fill in everything as needed.
For 10.5/10.6, System Preferences>Network, unlock the lock if need be, highlight the Interface you use to connect to Internet, click on the advanced button, click on the DNS tab, click on the little plus icon, then add these numbers...
208.67.222.222
208.67.220.220
Click OK.

Similar Messages

  • HT3466 Airport has self assigned IP address 169.254.153.51 and will not be able to connect to the Internet

    Cannot  connect to internet wirelessly because I get the message "AirPort has the self-assigned IP address 169.254.153.51 and will not be able to connect to the Internet."

    I would recommend that you do the following as a minimum:
    Power-down the modem, AirPort base station, and computer(s).
    Disconnect the AirPort base station from the Internet broadband modem.
    While all of the devices are powered-down, perform a "factory default" reset on the base station. This will get it back to its "out-of-the-box" configuration and make setting it up much easier, especially if you use the "Assist me" process within the AirPort Utility. (ref: Resetting an AirPort Base Station or Time Capsule)
    After the base station resets, go ahead and power it back down.
    Reconnect the AirPort base station to the Internet broadband modem. For the Extreme and Time Capsule, be sure to connect the cable to the base station's WAN (circle-of-dots) port.
    Power-up the modem; wait at least 10-15 minutes to allow it adequate time to initialize.
    Power-up the AirPort base station; wait at least 5-10 minutes. Note: The AirPort's status light may continue to flash amber after it has intialized. That is because, there may be some additional configuration items necessary, like setting up wireless security, before the overall setup is completed to get a green status.
    Power-up your computer(s).
    In this basic configuration, the AirPort base station will broadcast an unsecured wireless network with a Network Name (SSID) of Apple Network NNNNNN. Network clients, connected to the base station either by wire or wireless, should now be able to access the Internet through the ISP's modem. Once Internet connectivity has been verified, you can use the AirPort Utility to configure the base station for wireless security and any other desired options. Please post back your results.

  • My Airpot/Time capsule will not will not connect. It states " AirPort has the self addressed IP address 169.254.231.99 and will not connect to the internet??????l

    Cant' get my AirPort to sync up with internet.  I get the message "AirPort has the self addressed IP address 169.254.231.99 and will not connect to the internet. How do I fix?  Thanks.

    What broadband router do you have?
    What model Time Capsule do you have?
    If you changed the system over from another router.. have you rebooted the entire network.. particularly a cable modem.. did you power off for at least 20min..
    Tell us some info and we can help.

  • HT1338 my airport is not working getting Wi-Fi has the self-assigned IP address 169.254.5.29 and will not be able to connect to the Internet

    my wi fi wont work giving me this Wi-Fi has the self-assigned IP address 169.254.5.29 and will not be able to connect to the Internet whats up with the airport how do i fix it

    See this discussion.
    Wi-Fi has the self-assigned IP address
    Troubleshooting suggestions.
    Troubleshooting Wi-Fi issues in OS X
    Wireless Connection Problems - Fix
    Wireless Connection Problems - Fix (2)
    Wireless Connection Problems - Fix (3)
    Wireless Connection Problems - Fix (4)
    Wireless Diagnostics - About

  • IPad Wi-Fi has the self-assigned IP address 169.254.210.251 and will not be able to connect to the Internet.  How to fix?

    Mini connects to internet via cable modem fine.
    Want to have ipad connect also but mini Wi-Fi has the self-assigned IP address 169.254.210.251 and will not be able to connect to the Internet.  How to fix?

    Hello:
    I am a long way from a wi-fi expert, but.....
    You need, I think, either a router with wi-fi or an airport (express or extreme).  The iPad needs to connect to to a network.  In my case, I use an airport express and both my iMac and iPad 2 connect to the Internet through the airport device. 
    Barry

  • My Macbook Pro says Wi-Fi has the self-assigned IP address 169.254.74.157 and will not be able to connect to the internet.

    I just got my new Macbook Pro today. When I tried to connect it to my Wi-Fi at home it won't connect. I put in my WEP key correct every time and it keeps saying  "Wi-Fi has the self-assigned IP address 169.254.74.157 and will not be able to connect to the internet" . I connect my iPod touch to this same Wi-Fi all the time plus my other laptop and my phone and it works fine. Please help !! I  use Verizon Fios modem/router.

    Hi, it could be that the Router will not allow you onto the network..Reboot, Modem,Router & computer..
    Find out the native IP address for your Router & reset the network configs''
    Use Keychain Access to Delete all Internet/Router Passwords etc.. Then Roboot..

  • What doesWi-Fi has the self-assigned IP address 169.254.76.213 and will not be able to connect to the Internet

    This is what i get when i try to connect with wi fi at my local liberary: Since i updated to MOUNTAIN LION!!!
    Wi-Fi has the self-assigned IP address 169.254.76.213 and will not be able to connect to the Internet
    Although i can use Snow Leopard at the same Library via a external hard drive and when the same mbp was running Lion it also didn't have any issues connecting at the same library.
    Anyone can help out?????

    Do this the stuff you find at the bottom of this thread:
    https://discussions.apple.com/thread/3864270?tstart=0

  • Wi-Fi has the self-assigned IP address 169.254.82.22 and will not be able to connect to the Internet.

    I was watching my ATV3 and it suddenly stopped. When trying to reset things and get my wifi back I get the following message: Wi-Fi has the self-assigned IP address 169.254.82.22 and will not be able to connect to the Internet. I do not have clue to what happened or what to do next. Any help is appreciated.

    Power-Cycle the modem.... though it looks like your internet services may have gone down.. or something else upstream has gone kaut.

  • Wi-Fi has the self-assigned IP address 169.254.235.119 and will not be able to connect to the Internet.

    Wi-Fi has the self-assigned IP address 169.254.235.119 and will not be able to connect to the Internet.

    Reset the TC and make sure it is in the right mode.. ie router if you use a cable pure modem for instance.
    Or if you use a router combined modem.. put the TC in bridge mode.

  • Wi-Fi has self-assigned IP address 169.254.9.151 and will not be able to connect to the Internet

    In trying to setup my AirPort Extreme, it connects to the Internet on ethernetcables to computer but says it is not on WI-FI. I have configured it with all that I casn think of and yet I get, "Wi-Fi has self-assigned IP address 169.254.9.151 and will not be able to connect to the Internet." Can anyone tell me what is wrong?
    I did both a soft reset and a hard reset to no avail. PLEASE someone help!!
    Thanks!

    I would recommend that you do the following as a minimum:
    Power-down the modem, AirPort base station, and computer(s).
    Power-up the modem; wait at least 10-15 minutes to allow it adequate time to initialize.
    Power-up the AirPort base station; wait at least 5-10 minutes. Note: The AirPort's status light may continue to flash amber after it has intialized. That is because, there may be some additional configuration items necessary, like setting up wireless security, before the overall setup is completed to get a green status.
    Power-up your computer(s).
    If the above steps do not solve the problem, start over with step 1 above, but then perform the next steps between steps 1 & 2. above.
    Disconnect the AirPort base station from the Internet broadband modem.
    While all of the devices are powered-down, perform a "factory default" reset on the base station. This will get it back to its "out-of-the-box" configuration and make setting it up much easier, especially if you use the "Assist me" process within the AirPort Utility. (ref: Resetting an AirPort Base Station or Time Capsule)
    After the base station resets, go ahead and power it back down.
    Reconnect the AirPort base station to the Internet broadband modem. For the Extreme and Time Capsule, be sure to connect the cable to the base station's WAN (circle-of-dots) port.
    Continue with step 2 in the first set of steps.
    In this basic configuration, the AirPort base station will broadcast an unsecured wireless network with a Network Name (SSID) of Apple Network NNNNNN. Network clients, connected to the base station either by wire or wireless, should now be able to access the Internet through the ISP's modem. Once Internet connectivity has been verified, you can use the AirPort Utility to configure the base station for wireless security and any other desired options. Please post back your results.

  • Wi-Fi has the self-assigned IP address 169.254.197.32 and will not be able to connect to the Internet.

    Wi-Fi has the self-assigned IP address 169.254.197.32 and will not be able to connect to the Internet. How do you conncect the internet? I'm trying to hook up my wi-fi after It got screwed up somehow. Thanks! Greg

    Look at iOS Troubleshooting Wi-Fi networks and connections  http://support.apple.com/kb/TS1398
    iPad: Issues connecting to Wi-Fi networks  http://support.apple.com/kb/ts3304
    iOS: Recommended settings for Wi-Fi routers and access points  http://support.apple.com/kb/HT4199
    Additional things to try.
    Try this first. Turn Off your iPad. Then turn Off (disconnect power cord) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
    Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
    Change the channel on your wireless router (Auto is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
    Another thing to try - Go into your router security settings and change from WEP to WPA with AES.
    How to Quickly Fix iPad 3 Wi-Fi Reception Problems
    http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
    If none of the above suggestions work, look at this link.
    iPad Wi-Fi Problems: Comprehensive List of Fixes
    http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
    Fix iPad Wifi Connection and Signal Issues  http://www.youtube.com/watch?v=uwWtIG5jUxE
    Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
    Unable to Connect After iOS Update - saw this solution on another post.
    https://discussions.apple.com/thread/4010130
    Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
    ~~~~~~~~~~~~~~~
    If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
     Cheers, Tom

  • My iMac is locked on a bad IP address (169), how do I get it to release so I can connect to the internet?

    My iMac is locked on a bad IP address (169), how do I get it to release so I can connect to the internet?

    Welcome to the Apple Community.
    Try unplugging the Apple Tv and restarting and restating your router. You should also check that the Apple Tv is set to use the correct location.

  • IP address 169.x.x.x

    Hi,
    I got a used powermac G4 DP 733Mhz. I am trying to connect it DLink Router. When configured with DHCP it shows assigned IP address as 169.x.x.x
    Then I can't connect to internet or the router itself
    I have another powermac DP 1Ghz(which works fine with same ethernet cable and router.
    I tried lot of things so far (spend 4-6 hours trying all combinations DHCP, Manual, Turning on /OFF , resetting Router etc)
    Still no luck. It does detect connection. When I remove cable I see "connection down" in the console window.
    Powermac doesn't want to give up that stupid IP address 169.x.x.x. Is there any system files it needs ?
    I really need help

    Hi could be some files, but on Manually, try 1 more than the last number than the other one has.
    Say the working one has...
    IP: 192.168.1.2
    Subnet Mask: 255.255.255.0
    Router: 192.168.1.1
    Try this one with...
    IP: 192.168.1.3
    Subnet Mask: 255.255.255.0
    Router: 192.168.1.1
    Then... Try putting these numbers in Network>TCP/IP>DNS Servers, for the Interface you connect with...
    208.67.222.222
    208.67.220.220
    Then Apply

  • Wi-Fi has the self-assigned IP address 169.254.21.127

    Hi
    I am having problems with my iPad and it looks like it's coming from my iMac because in the Network it says "Wi-Fi has the self-assigned IP address 169.254.21.127 and will not be able to connect to the Internet." but I have been connected to the internet from my iPad through my iMac for over six months, it's only since updating to Lion that the problem started. Any help please.
    George

    the solution is here.
    https://discussions.apple.com/message/16224461#16224461
    i had the same issue. but now it all works like it used to.

  • Finding Internet ip Address

    my project depends on ip address...if a system is using proxy ip address for internet connection..My lan ip is different and internet ip address is differen...By java code i found lan ip ...Is it possible to find the internet proxy ip address using java code...in http://www.haxial.com/whatismyipaddress they have achieved.pLEASE IF ANYBODY IS HAVING THE CODE for finding internet proxy ip address..pLEASE SEND ME

    hi nivaz_sharma,
    You need the public ip address of you pc connected to internet through a proxy. first of all why do you need your public ipaddress. Are you communicating with another application over the internet. If it is so then you can ask that application itself using whatever protocol you are using aboute your own ip address as it will to knowing your public ipaddress only. In case your protocol does not supports such query (if you are using a standard protocol such as http smtp pop3) then you can implement your own server that provides this functonlity and place that server outside your network on the internet. If you want i can give you the source code for such server.
    Hope that would help,
    VJ

Maybe you are looking for

  • Sample code for sap hr program--pls treat this as urgent

    Hi , This is the program on attendence incentive program, i have written REPORT  zhrpa0019    LINE-SIZE 270                      LINE-COUNT  55(3)                      NO STANDARD PAGE HEADING                      MESSAGE-ID zm.      T A B L E S     

  • Logo download to pdf file.

    Hi all, I need to download a logo which is available in se78 into pdf along with report output and send as mail attachment can you suggest me how to go about. I have searched in the forum and didnt find apt solution.

  • CiscoWorks Tomcat Servlet Engine service does not start

    Hello! CiscoWorks  Tomcat Servlet Engine service does not start. Events in the Windows Event Viewer: The CiscoWorks Tomcat Servlet Engine service terminated unexpectedly. It has done this 1 time(s). output pdshow and file stderr.log,  hs_err_pid2128.

  • Spry textfield validation for alphanumeric input

    Hi, How can I set the spry input to the following pattern that I need: only allow alphanumeric.

  • Did Adobe fall in the trap, or what?

    I wonder WHY did Adobe let Google make their own crappy Flash player version (Pepper) in Chrome? The performance in all applications is inferior.  It sucks in displaying textfields, it sucks in displaying all other graphical display objects, it sucks