No Internet with AEBS.

I had my iMac setup to connect to the Internet via an AEBS that was hooked directly to my cable modem. I had lightening to strike near my house that nuked a cable modem and an AEBS. I have them replaced now and ran through the same setup I had before, but now I cannot connect to the Internet when using the prior setup I perviously mentioned. What gives? Would it have something to do with MAC addresses?

Since you know have new network components, you want to make sure that they synchronize properly. To do so:
- Power down your modem, AEBS, and clients.
- Power up the modem; Wait at least 30 minutes.
- Power up the AEBS; Wait at least 5 minutes.
- Power up your clients

Similar Messages

  • I can connect to network, but can't connect to internet with aebs

    so i got a new Airport Extreme Base Station, hoping to replace my old og airport. i can connect to the new AEBS network easily, but i can't connect to the internet. with the old airport, i can connect to the internet no problem, hence i can write this post. "internet connect" tells me:
    +old, space ship looking airport:+
    connected to "myNetwork"
    connected to the internet via ethernet
    +new and improved AEBS:+
    Connected to "myNetwork"
    but that's it. any ideas would be greatly appreciated. oh also, it seems to be running pretty hot. is that normal? thanks!

    Hello mookyee. Welcome to the Apple Discussions!
    It's always a good idea to power recycle all of your network components when changing configurations ...
    Try the following, in order, checking for Internet access after each step, until resolved:
    1. If the modem has a reset switch, use it to reset the modem. Wait at least 5-10 minutes for the modem to initialize.
    2. Remove power from the modem. If it has a backup battery, remove this as well. Wait 5-10 minutes. Replace the battery, and add power back to the modem.
    3. Perform a complete power recycle of your network components as follows:
    Modem/Router Power Recycling - Quick
    o Power-off the modem, 802.11n AirPort Extreme Base Station (AEBSn), & computer(s); Wait at least 5 minutes.
    o Power-on the modem; Wait at least 5 minutes.
    o Power-on the AEBSn; Wait at least 5 minutes.
    o Power-on the computer(s)
    If this fails to get the modem to "recognize" the Internet router, then try the "Full" version.
    Modem/Router Power ReCycling - Full
    o Power-off the modem, AEBSn, & computer(s). (Wait at least 30 minutes. If possible, leave the modem off overnight.)
    o Power-on the modem; Wait at least 15 minutes.
    o Power-on the AEBSn; Wait at least 5 minutes.
    o Power-on the computer(s)
    4. Contact your ISP to have them perform a "modem reset."

  • Problems connecting to internet with AEBS

    Equipment: MacBookPro (OS 10.5.3), AEBS (v.7.2.1), iMac (OS10.5.3)
    MacBookPro is about 20+ feet from AEBS, iMac using same AEBS, about 3 feet away. Time Warner cable modem. When I try to connect to internet on MBP, nearly every time it fails and if I do manage to get on it is slower than the slowest dial-up. If I then go into network diagnostics and go through the whole 9 yards of setting it up, I can usually connect but connection is often slow. Needless to say, this is a royal pain since my work requires me to go on line frequently. Am pretty sure the trouble started when we hooked up the iMac, but not 100% certain. Went to see the "genius" who was stymied.
    Just did some trouble shooting - switched the locations of the computers and both seem to be working fine and at speed I'd expect given equipment and cable modem. So now I'm thinking there is something about the MBP and its distance from the AEBS, since why both would work fine when we switched their locations?
    Any thoughts out there?
    Thanks for your time.

    Although, I know that you mentioned that you have reset your AirPort, I strongly suggest that you perform a complete power recycle of your network components to see if this will get the modem and your AEBSn communicating properly.
    Please try the following:
    o Power-down the modem, AEBSn, and computer(s); wait at least 10-15 minutes. Order is not critical.
    o Power-up the modem. If it has a reset switch, go ahead and perform a modem reset. After the reset, wait at least 10-15 minutes.
    o Power-up the AEBSn; wait at least 5-10 minutes.
    o Power-up the computer(s).
    Your computer(s) should now be able to access the Internet thru the AEBSn either by wire or wireless. Please post back your results.

  • Getting bars but no internet with new airport extreme

    HI,
    I purchased a new AEBS for my restaurant. I set it up and it worked great. My Powerbook g4 was connecting and I was getting internet fine. The next time I went to the restaurant and opened my Powerbook I was getting airport bars but was unable to connect. My son has a Powerbook as well and he is connecting just fine. Several customers came in with Macs and they were also unable to connect. I know I'm getting internet from the modem. I've tried unplugging both the modem and AEBS and then reconnecting with no resolution. I've tried to re-set up the AEBS but it says it is not getting the IP address. I'm about to throw out the AEBS and go get a Linksys!
    I've read other posts of folks with this same problem and one of the solutions is to roll back to a previous firmware version. How is that done?
    Powerbook G4 aluminum, 1.25ghz
    Thanks for any help

    I have no problem gettiing the Macbook pro to set itself up on the Airport Network. I can NOT, though, access the internet. I even tried to type in the IP address for the DSL modem while connected to Airport base and can not connect to modem. Does anyone have any advice? Is there a bridging function in the Airport Base that has to be activated?
    Make sure you perform a complete power recycle when switching network components.
    Modem/Router Power ReCycling
    - Power-off the DSL modem & AEBS. (Wait at least 30 minutes. If possible, leave the modem off overnight.)
    - Power-on the DSL modem; Wait at least 30 minutes.
    - Power-on the AEBS; Wait at least 5 minutes.
    If that doesn't resolve the problem, and your DSL ISP requires PPPoE for connectivity, you will need to set that up on your AirPort Extreme Base Station (AEBS) as follows:
    Connect your computer directly (using an Ethernet cable) to the LAN port of the AEBS, and then, using the AirPort Admin Utility, check these settings:
    Internet tab
    - Connect Using: PPP over Ethernet (PPPoE)
    - Account Name: <ISP account name>
    - Change password: <ISP password>
    - Always stay connected (checked)
    - WAN Ethernet Port: Automatic
    Another question. If I replace my current DSL Router with a wireless router, do I even need the airport base if all I want to do it connect to the internet with the laptop?
    No, the AEBS will no longer be required.

  • ADSL Modem Compatible with AEBS

    I'd be grateful if anyone could recommend an ADSL modem compatible with AEBS. The NetGear ADSL 2+ Ethernet Modem advertised in the Online Store is very poorly rated.

    Pretty much any ADSL modem that provides a regular internet connection with an RJ-45 cable would work with the AEBSn. More importantly you should ensure that the ADSL modem you purchase is compatible with your ISP ADSL connection. In most cases, the ISP provides a "custom" version of a ADSL retail modem with firmware modified for ISP tech support.

  • Help - Snow Leopard Server Setup with AEBS

    Hi.
    I am trying to setup two things at once. Good start, eh ;0)
    Step-by-step, this is what I have:
    Internet connection
    Static IP address
    Apple Airport Extreme Base Station
    Mac Mini Server (Snow Leopard)
    Registered Domain name with access to control panel for the name
    This is what I want to do:
    Connect the AEBS to the Internet
    Connect the Server to the Internet via AEBS
    Connect Client computers (all Mac, iPhone & iPad) to the server network and the internet locally
    Connect Client computers (all Mac, iPhone & iPad) to the server network and the internet remotely
    This is the information that I have been given by my ISP (I have added letters before the address to help you to help me identify where they should be entered):
    Router IP: (a)192.xxx.94.x (maps to (b)195.xxx.xx.xx)
    Subnet Mask: (c)255.255.255.0
    Default Gateway: (d)192.xxx.94.x
    DNS 1: (e)192.xxx.50.xx1
    DNS 2: (f)192.xxx.50.xx2
    SMTP: (g)smtp.xx.net
    I can't really find any obvious instructions, particularly about pointing my domain name to the router/server. Do I change the name servers/the A records, the A&MX Records on the domain control panel?
    If anyone has any experience with setting-up the server with an AEBS, I would be truly grateful for some pointers! e.g. put IP address (a) in box (x)
    Ha! if only it were that easy, but any help would be appreciated.
    Thanks in advance.

    Easy answer. Paid a local IT company to come and check my settings. Turns out that due to the office that I am in, I am in a 'double NAT' environment. When AEBS was throwing-up NAT errors, I was unsure about continuing.
    Al sorted now with a few phone calls to the ISP and 2 hours' work by the IT company. Done. What else can I try and break???

  • WRT 120N- Cannot connect to the internet with more than one PC at a time.

    Before I went on a three month vacation,I could connect 3 or 4 PC's either wireless or wired to my router with no problems at all.I have a desk top and a laptop computer which I use at home.After I returned,I found that I could connect to the internet with only one PC at a time.
    If I was say,connected via my laptop,my desk top would continuously keep getting disconnected and vice versa.I have been reading the suggestions from experts here and have done a few checks based on them.I also cannot get to my router page which is 192.168.1.1 I keep getting a message that says "Problem Loading Page" and this happens with both,Firefox and Internet Explorer.I am running Windows 7 - 32 bit on my desk top and Vista Home Premium on my laptop.
    I have opened the "Command Prompt" dialogue and pinged 192.168.1.1 and thereafter I typed in "ipconfig".These are the results:
    Microsoft Windows [Version 6.0.6002]
    Copyright (c) 2006 Microsoft Corporation.  All rights reserved.
    C:\Users\Gordon>ping 192.168.1.1
    Pinging 192.168.1.1 with 32 bytes of data:
    Reply from 192.168.1.1: bytes=32 time<1ms TTL=111
    Reply from 192.168.1.1: bytes=32 time<1ms TTL=111
    Reply from 192.168.1.1: bytes=32 time<1ms TTL=111
    Reply from 192.168.1.1: bytes=32 time<1ms TTL=111
    Ping statistics for 192.168.1.1:
        Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
    Approximate round trip times in milli-seconds:
        Minimum = 0ms, Maximum = 0ms, Average = 0ms
    C:\Users\Gordon>ipconfig
    Windows IP Configuration
    PPP adapter Brownwolf:
       Connection-specific DNS Suffix  . :
       IPv4 Address. . . . . . . . . . . : 92.98.42.65
       Subnet Mask . . . . . . . . . . . : 255.255.255.255
       Default Gateway . . . . . . . . . : 0.0.0.0
    Ethernet adapter Local Area Connection* 22:
       Media State . . . . . . . . . . . : Media disconnected
       Connection-specific DNS Suffix  . :
    Wireless LAN adapter Wireless Network Connection:
       Connection-specific DNS Suffix  . :
       IPv6 Address. . . . . . . . . . . : 2002:5c62:2a41:c:35a2:8753:8832:f494
       Site-local IPv6 Address . . . . . : fec0::c:35a2:8753:8832:f494%2
       IPv6 Address. . . . . . . . . . . : 2002:5661:4cc9:c:35a2:8753:8832:f494
       Temporary IPv6 Address. . . . . . : 2002:5661:4cc9:c:a408:59a3:918e:f0ab
       Temporary IPv6 Address. . . . . . : 2002:5c62:2a41:c:a408:59a3:918e:f0ab
       Link-local IPv6 Address . . . . . : fe80::35a2:8753:8832:f494%12
       IPv4 Address. . . . . . . . . . . : 192.168.0.1
       Subnet Mask . . . . . . . . . . . : 255.255.255.0
       Default Gateway . . . . . . . . . :
    Ethernet adapter Local Area Connection:
       Connection-specific DNS Suffix  . :
       IPv6 Address. . . . . . . . . . . : 2002:5c62:2a41:c:413:cf4f:77af:474d
       Site-local IPv6 Address . . . . . : fec0::c:413:cf4f:77af:474d%1
       IPv6 Address. . . . . . . . . . . : 2002:5661:4cc9:c:413:cf4f:77af:474d
       Temporary IPv6 Address. . . . . . : 2002:5661:4cc9:c:1591:ad9:13da:8fea
       Temporary IPv6 Address. . . . . . : 2002:5c62:2a41:c:1591:ad9:13da:8fea
       Link-local IPv6 Address . . . . . : fe80::413:cf4f:77af:474d%11
       IPv4 Address. . . . . . . . . . . : 192.168.1.100
       Subnet Mask . . . . . . . . . . . : 255.255.255.0
       Default Gateway . . . . . . . . . : fe80::35a2:8753:8832:f494%11
                                           192.168.1.1
    Tunnel adapter Local Area Connection* 7:
       Media State . . . . . . . . . . . : Media disconnected
       Connection-specific DNS Suffix  . :
    Tunnel adapter Local Area Connection* 11:
       Media State . . . . . . . . . . . : Media disconnected
       Connection-specific DNS Suffix  . :
    Tunnel adapter Local Area Connection* 14:
       Media State . . . . . . . . . . . : Media disconnected
       Connection-specific DNS Suffix  . :
    Tunnel adapter Local Area Connection* 15:
       Media State . . . . . . . . . . . : Media disconnected
       Connection-specific DNS Suffix  . :
    Tunnel adapter Local Area Connection* 19:
       Media State . . . . . . . . . . . : Media disconnected
       Connection-specific DNS Suffix  . :
    Tunnel adapter Local Area Connection* 20:
       Connection-specific DNS Suffix  . :
       IPv6 Address. . . . . . . . . . . : 2002:5c62:2a41::5c62:2a41
       Default Gateway . . . . . . . . . : 2002:c058:6301::c058:6301
    Tunnel adapter Local Area Connection* 23:
       Media State . . . . . . . . . . . : Media disconnected
       Connection-specific DNS Suffix  . :
    Tunnel adapter Local Area Connection* 24:
       Media State . . . . . . . . . . . : Media disconnected
       Connection-specific DNS Suffix  . :
    Tunnel adapter Local Area Connection* 28:
       Media State . . . . . . . . . . . : Media disconnected
       Connection-specific DNS Suffix  . :
    I presume that this model is a modem **bleep** router as I do not have a separate modem with my system.I have a DSL connection and the firmware version of my router is ver.1.0.If I recall,I did upgrade to the next firmware upgrade a few months after I purchased the router but I am not sure.
    I use both my PC's to run a small business venture and I am worried that resetting the router may cause some other problems and will stop me from using the internet.
    The Command Prompt information above was taken from my laptop.
    Any help will be really appreciated.
    Gerard.
    Solved!
    Go to Solution.

    brownwolf66 wrote:
    No,I have a desk top and a laptop and I cannot access 192.168.1.1 on either of them.In my OP,I have used the Command Prompt dialogue on both computers to ping 192.168.1.1 and I have attached the results.This is what I got:
    Microsoft Windows [Version 6.0.6002]
    Copyright (c) 2006 Microsoft Corporation.  All rights reserved.
    C:\Users\Gordon>ping 192.168.1.1
    Pinging 192.168.1.1 with 32 bytes of data:
    Reply from 192.168.1.1: bytes=32 time<1ms TTL=111
    Reply from 192.168.1.1: bytes=32 time<1ms TTL=111
    Reply from 192.168.1.1: bytes=32 time<1ms TTL=111
    Reply from 192.168.1.1: bytes=32 time<1ms TTL=111
    Ping statistics for 192.168.1.1:
        Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
    Approximate round trip times in milli-seconds:
        Minimum = 0ms, Maximum = 0ms, Average = 0ms
    The results I obtained using ipconfig in the command prompt have already been mentioned in my OP.
    I do not know if the above result is what it is supposed to be but I still cannot access my router's home page.How do I verify if there is a proxy server and if there is one,how do I disable it in my browsers?This problem occured suddenly as a few months earlier all was well.It's getting rather frustrating.
    I suggest resetting the router. Make sure firmware is updated. You can download it here - http://homesupport.cisco.com/en-us/support/routers/WRT120N. After firmware upgrade, reset and reconfigure. Just access the link below to guide you setting up the router.
    * Setting up a Linksys router for DSL Internet connection
    http://www6.nohold.net/Cisco2/ukp.aspx?vw=1&docid=20ee1457387f40178cd5f41d4b585db4_3687.xml&pid=80&r...
    * Setting up a Linksys router with Cable Internet service
    http://www6.nohold.net/Cisco2/ukp.aspx?vw=1&docid=0ff4c94586a345d082828ec2161aaecf_3686.xml&pid=80&r...

  • How do I connect to the internet with Airport Expess?

    In Airport Utility I get an orange icon and the Airport Express light is green. In the internet box
    coming from the globe picture it says Interent connection Disconnected and there is no router address
    and no DNS server information shown.

    As a minimum, in order to gain access to the Internet with an AirPort Express base station, you will need an Internet Service Provider (ISP) AND an Internet modem or gateway device.
    What is the make & model of the Internet modem or gateway device that you have the AirPort Express directly connected to by Ethernet? What exact model of Express do you have?

  • How do I connect to the internet with Airport for the first time?

    I just got my Airport express and I've been trying to configure it to connect to the internet but it doesn't work and I can't find info on the configurations. I have an ethernet "modem" which I used to connect the cable coming from it to the computer and now I connect it to my Airport. Although the green light is on and in network preferences, it tells me I'm connected to the internet, I can't browse the internet with Safari, etc. I've been trying to find information on how to configure the base station in Airport Admin Utility but there is no specific information. Is there anyone who could help me telling me how to set up the IP adress, if I need one, DHCP, preferences in Airport Admin Utility?? If the ethernet cable is connected to the computer directly I don't need a user ID or anything... It's all setup automatically.

    As a minimum, in order to gain access to the Internet with an AirPort Express base station, you will need an Internet Service Provider (ISP) AND an Internet modem or gateway device.
    What is the make & model of the Internet modem or gateway device that you have the AirPort Express directly connected to by Ethernet? What exact model of Express do you have?

  • How do I connect to the internet with my new IPAD ?

    How do I connect to the internet with myt new Ipad

    See here for connecting to the Internet:
    http://support.apple.com/kb/HT1695
    If you have any problems there is troubleshooting advice here: http://www.apple.com/support/ipad/wifi/

  • How do i connect to the internet with my ipad?

    how do i connect to the internet with my ipad?

    Did you turn WiFi on in the Settings App? If WiFi is turned on, your iPad should be able to see any WiFi networks that you can connect to and you should be able to tap on one of those, enter a password if needed and then tap the join button.
    I get the feeling that you know this and the problem needs further explanation so ... Can you explain in more detail?

  • How do i connect to the internet with apple tv

    how do i connect to the internet with apple tv

    Ethernet cable from your router, or configure wifi in Settings.

  • How do i use my iMac and the macs wired internet connection to share the internet with my iPod and iPhone

    How do i use my iMac and the macs wired internet connection to share the internet with my iPod and iPhone. For 6months I had set up a network that shared the internet through bluetooth to my iPod 5th gen but i messed it up when i tried to add my iPhone 5s and i can't remember how to do it.

    The following has instructions: OS X Mavericks: Share your Internet connection

  • I can't access the internet with Firefox on my computer (Windows 7 PC). I have used Firefox as my browser for 1 year but 5 days ago it stopped working even though Internet Explorer worked fine. I can't solve the problem and need some help.Randy Brown

    September 26, 2011
    Dear Mozilla,
    I am having some difficulty accessing the internet with Firefox on one of my PC computers. I normally use Mozilla Firefox as my web browser and google is my homepage and gmail is my email system. The operating system is Windows 7. For over a year this system worked perfectly but a few days ago it stopped working. When I launch Firefox now I get the message that that website (www.google.com) is unavailable. In fact, I can’t access any website and I am blocked from the internet entirely within Firefox. My internet connection is fine because Internet Explorer works fine. I can access google and any other website within that web browser. I have investigated all the security issue I can manage and found no smoking gun. I’ve tried uninstalling and reinstalling Firefox to no avail. Is Windows 7 compromising the effectiveness of Firefox? Any suggestions or other assistance you can offer would be appreciated.
    Sincerely,
    Randy Brown
    [email protected]

    You only have to clone your mac when using certain cable modem.  You don't clone your mac when using dsl.
    Greetings from Northern Ontario, Canada

  • Can't connect macbook pro to internet with airport extreme

    Can't connect macbook pro to internet with airport extreme

    If you have ethernet still on your MBP plug it in by ethernet and tell me if that works.
    Tell me how the Airport is setup.. what broadband modem and router you have.
    What OS on the laptop? Yosemite I guess.. since it is the most troublesome.
    Did it work before whatever change was made? Has it worked in the past? When did it stop and what did you do that coincided with it stopping?
    Upgrade to Yosemite??

Maybe you are looking for