No internet with Droid X2

First question is this phone WiFi ONLY? My old phone which was a blackberry could access the internet at my house without all this wifi, tethering, etc nonsense.
I cannot get any WiFi connection at my house. Is there a way to connect to net without WiFi or am I going to have to get a different phone?

Have you tried a HARD RESET? 
Boot in Recovery Mode Wipe: - Wipes system configuration settings and loads default settings but keeps personal data saved on system, normally used to recover from a none boot status without loosing personal data.  There is times that Personal Data gets wiped also with this process..
Power Device Off First.....
1. Hold Home Button and press power
2. Screen will show a Android with a triangle with astrick
3. Let Go of Home Button and Power
4. Press Search Button (Far RIGHT Button)
5. A blue menu will show at top of page, scroll to Format Device
6. Select Yes to verify
7. Allow format to complete (Information at bottom of page will go through a few steps)
8. Once Format is complete Blue Menu will show at top again, select Reboot
Note: Use volume up and down to select opinion and use camera button as Enter,,,
(thanks Wildman)

Similar Messages

  • WRT 120N- Cannot connect to the internet with more than one PC at a time.

    Before I went on a three month vacation,I could connect 3 or 4 PC's either wireless or wired to my router with no problems at all.I have a desk top and a laptop computer which I use at home.After I returned,I found that I could connect to the internet with only one PC at a time.
    If I was say,connected via my laptop,my desk top would continuously keep getting disconnected and vice versa.I have been reading the suggestions from experts here and have done a few checks based on them.I also cannot get to my router page which is 192.168.1.1 I keep getting a message that says "Problem Loading Page" and this happens with both,Firefox and Internet Explorer.I am running Windows 7 - 32 bit on my desk top and Vista Home Premium on my laptop.
    I have opened the "Command Prompt" dialogue and pinged 192.168.1.1 and thereafter I typed in "ipconfig".These are the results:
    Microsoft Windows [Version 6.0.6002]
    Copyright (c) 2006 Microsoft Corporation.  All rights reserved.
    C:\Users\Gordon>ping 192.168.1.1
    Pinging 192.168.1.1 with 32 bytes of data:
    Reply from 192.168.1.1: bytes=32 time<1ms TTL=111
    Reply from 192.168.1.1: bytes=32 time<1ms TTL=111
    Reply from 192.168.1.1: bytes=32 time<1ms TTL=111
    Reply from 192.168.1.1: bytes=32 time<1ms TTL=111
    Ping statistics for 192.168.1.1:
        Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
    Approximate round trip times in milli-seconds:
        Minimum = 0ms, Maximum = 0ms, Average = 0ms
    C:\Users\Gordon>ipconfig
    Windows IP Configuration
    PPP adapter Brownwolf:
       Connection-specific DNS Suffix  . :
       IPv4 Address. . . . . . . . . . . : 92.98.42.65
       Subnet Mask . . . . . . . . . . . : 255.255.255.255
       Default Gateway . . . . . . . . . : 0.0.0.0
    Ethernet adapter Local Area Connection* 22:
       Media State . . . . . . . . . . . : Media disconnected
       Connection-specific DNS Suffix  . :
    Wireless LAN adapter Wireless Network Connection:
       Connection-specific DNS Suffix  . :
       IPv6 Address. . . . . . . . . . . : 2002:5c62:2a41:c:35a2:8753:8832:f494
       Site-local IPv6 Address . . . . . : fec0::c:35a2:8753:8832:f494%2
       IPv6 Address. . . . . . . . . . . : 2002:5661:4cc9:c:35a2:8753:8832:f494
       Temporary IPv6 Address. . . . . . : 2002:5661:4cc9:c:a408:59a3:918e:f0ab
       Temporary IPv6 Address. . . . . . : 2002:5c62:2a41:c:a408:59a3:918e:f0ab
       Link-local IPv6 Address . . . . . : fe80::35a2:8753:8832:f494%12
       IPv4 Address. . . . . . . . . . . : 192.168.0.1
       Subnet Mask . . . . . . . . . . . : 255.255.255.0
       Default Gateway . . . . . . . . . :
    Ethernet adapter Local Area Connection:
       Connection-specific DNS Suffix  . :
       IPv6 Address. . . . . . . . . . . : 2002:5c62:2a41:c:413:cf4f:77af:474d
       Site-local IPv6 Address . . . . . : fec0::c:413:cf4f:77af:474d%1
       IPv6 Address. . . . . . . . . . . : 2002:5661:4cc9:c:413:cf4f:77af:474d
       Temporary IPv6 Address. . . . . . : 2002:5661:4cc9:c:1591:ad9:13da:8fea
       Temporary IPv6 Address. . . . . . : 2002:5c62:2a41:c:1591:ad9:13da:8fea
       Link-local IPv6 Address . . . . . : fe80::413:cf4f:77af:474d%11
       IPv4 Address. . . . . . . . . . . : 192.168.1.100
       Subnet Mask . . . . . . . . . . . : 255.255.255.0
       Default Gateway . . . . . . . . . : fe80::35a2:8753:8832:f494%11
                                           192.168.1.1
    Tunnel adapter Local Area Connection* 7:
       Media State . . . . . . . . . . . : Media disconnected
       Connection-specific DNS Suffix  . :
    Tunnel adapter Local Area Connection* 11:
       Media State . . . . . . . . . . . : Media disconnected
       Connection-specific DNS Suffix  . :
    Tunnel adapter Local Area Connection* 14:
       Media State . . . . . . . . . . . : Media disconnected
       Connection-specific DNS Suffix  . :
    Tunnel adapter Local Area Connection* 15:
       Media State . . . . . . . . . . . : Media disconnected
       Connection-specific DNS Suffix  . :
    Tunnel adapter Local Area Connection* 19:
       Media State . . . . . . . . . . . : Media disconnected
       Connection-specific DNS Suffix  . :
    Tunnel adapter Local Area Connection* 20:
       Connection-specific DNS Suffix  . :
       IPv6 Address. . . . . . . . . . . : 2002:5c62:2a41::5c62:2a41
       Default Gateway . . . . . . . . . : 2002:c058:6301::c058:6301
    Tunnel adapter Local Area Connection* 23:
       Media State . . . . . . . . . . . : Media disconnected
       Connection-specific DNS Suffix  . :
    Tunnel adapter Local Area Connection* 24:
       Media State . . . . . . . . . . . : Media disconnected
       Connection-specific DNS Suffix  . :
    Tunnel adapter Local Area Connection* 28:
       Media State . . . . . . . . . . . : Media disconnected
       Connection-specific DNS Suffix  . :
    I presume that this model is a modem **bleep** router as I do not have a separate modem with my system.I have a DSL connection and the firmware version of my router is ver.1.0.If I recall,I did upgrade to the next firmware upgrade a few months after I purchased the router but I am not sure.
    I use both my PC's to run a small business venture and I am worried that resetting the router may cause some other problems and will stop me from using the internet.
    The Command Prompt information above was taken from my laptop.
    Any help will be really appreciated.
    Gerard.
    Solved!
    Go to Solution.

    brownwolf66 wrote:
    No,I have a desk top and a laptop and I cannot access 192.168.1.1 on either of them.In my OP,I have used the Command Prompt dialogue on both computers to ping 192.168.1.1 and I have attached the results.This is what I got:
    Microsoft Windows [Version 6.0.6002]
    Copyright (c) 2006 Microsoft Corporation.  All rights reserved.
    C:\Users\Gordon>ping 192.168.1.1
    Pinging 192.168.1.1 with 32 bytes of data:
    Reply from 192.168.1.1: bytes=32 time<1ms TTL=111
    Reply from 192.168.1.1: bytes=32 time<1ms TTL=111
    Reply from 192.168.1.1: bytes=32 time<1ms TTL=111
    Reply from 192.168.1.1: bytes=32 time<1ms TTL=111
    Ping statistics for 192.168.1.1:
        Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
    Approximate round trip times in milli-seconds:
        Minimum = 0ms, Maximum = 0ms, Average = 0ms
    The results I obtained using ipconfig in the command prompt have already been mentioned in my OP.
    I do not know if the above result is what it is supposed to be but I still cannot access my router's home page.How do I verify if there is a proxy server and if there is one,how do I disable it in my browsers?This problem occured suddenly as a few months earlier all was well.It's getting rather frustrating.
    I suggest resetting the router. Make sure firmware is updated. You can download it here - http://homesupport.cisco.com/en-us/support/routers/WRT120N. After firmware upgrade, reset and reconfigure. Just access the link below to guide you setting up the router.
    * Setting up a Linksys router for DSL Internet connection
    http://www6.nohold.net/Cisco2/ukp.aspx?vw=1&docid=20ee1457387f40178cd5f41d4b585db4_3687.xml&pid=80&r...
    * Setting up a Linksys router with Cable Internet service
    http://www6.nohold.net/Cisco2/ukp.aspx?vw=1&docid=0ff4c94586a345d082828ec2161aaecf_3686.xml&pid=80&r...

  • How do I connect to the internet with Airport Expess?

    In Airport Utility I get an orange icon and the Airport Express light is green. In the internet box
    coming from the globe picture it says Interent connection Disconnected and there is no router address
    and no DNS server information shown.

    As a minimum, in order to gain access to the Internet with an AirPort Express base station, you will need an Internet Service Provider (ISP) AND an Internet modem or gateway device.
    What is the make & model of the Internet modem or gateway device that you have the AirPort Express directly connected to by Ethernet? What exact model of Express do you have?

  • How do I connect to the internet with Airport for the first time?

    I just got my Airport express and I've been trying to configure it to connect to the internet but it doesn't work and I can't find info on the configurations. I have an ethernet "modem" which I used to connect the cable coming from it to the computer and now I connect it to my Airport. Although the green light is on and in network preferences, it tells me I'm connected to the internet, I can't browse the internet with Safari, etc. I've been trying to find information on how to configure the base station in Airport Admin Utility but there is no specific information. Is there anyone who could help me telling me how to set up the IP adress, if I need one, DHCP, preferences in Airport Admin Utility?? If the ethernet cable is connected to the computer directly I don't need a user ID or anything... It's all setup automatically.

    As a minimum, in order to gain access to the Internet with an AirPort Express base station, you will need an Internet Service Provider (ISP) AND an Internet modem or gateway device.
    What is the make & model of the Internet modem or gateway device that you have the AirPort Express directly connected to by Ethernet? What exact model of Express do you have?

  • How do I connect to the internet with my new IPAD ?

    How do I connect to the internet with myt new Ipad

    See here for connecting to the Internet:
    http://support.apple.com/kb/HT1695
    If you have any problems there is troubleshooting advice here: http://www.apple.com/support/ipad/wifi/

  • How do i connect to the internet with my ipad?

    how do i connect to the internet with my ipad?

    Did you turn WiFi on in the Settings App? If WiFi is turned on, your iPad should be able to see any WiFi networks that you can connect to and you should be able to tap on one of those, enter a password if needed and then tap the join button.
    I get the feeling that you know this and the problem needs further explanation so ... Can you explain in more detail?

  • How do i connect to the internet with apple tv

    how do i connect to the internet with apple tv

    Ethernet cable from your router, or configure wifi in Settings.

  • How do i use my iMac and the macs wired internet connection to share the internet with my iPod and iPhone

    How do i use my iMac and the macs wired internet connection to share the internet with my iPod and iPhone. For 6months I had set up a network that shared the internet through bluetooth to my iPod 5th gen but i messed it up when i tried to add my iPhone 5s and i can't remember how to do it.

    The following has instructions: OS X Mavericks: Share your Internet connection

  • Getting bars but no internet with new airport extreme

    HI,
    I purchased a new AEBS for my restaurant. I set it up and it worked great. My Powerbook g4 was connecting and I was getting internet fine. The next time I went to the restaurant and opened my Powerbook I was getting airport bars but was unable to connect. My son has a Powerbook as well and he is connecting just fine. Several customers came in with Macs and they were also unable to connect. I know I'm getting internet from the modem. I've tried unplugging both the modem and AEBS and then reconnecting with no resolution. I've tried to re-set up the AEBS but it says it is not getting the IP address. I'm about to throw out the AEBS and go get a Linksys!
    I've read other posts of folks with this same problem and one of the solutions is to roll back to a previous firmware version. How is that done?
    Powerbook G4 aluminum, 1.25ghz
    Thanks for any help

    I have no problem gettiing the Macbook pro to set itself up on the Airport Network. I can NOT, though, access the internet. I even tried to type in the IP address for the DSL modem while connected to Airport base and can not connect to modem. Does anyone have any advice? Is there a bridging function in the Airport Base that has to be activated?
    Make sure you perform a complete power recycle when switching network components.
    Modem/Router Power ReCycling
    - Power-off the DSL modem & AEBS. (Wait at least 30 minutes. If possible, leave the modem off overnight.)
    - Power-on the DSL modem; Wait at least 30 minutes.
    - Power-on the AEBS; Wait at least 5 minutes.
    If that doesn't resolve the problem, and your DSL ISP requires PPPoE for connectivity, you will need to set that up on your AirPort Extreme Base Station (AEBS) as follows:
    Connect your computer directly (using an Ethernet cable) to the LAN port of the AEBS, and then, using the AirPort Admin Utility, check these settings:
    Internet tab
    - Connect Using: PPP over Ethernet (PPPoE)
    - Account Name: <ISP account name>
    - Change password: <ISP password>
    - Always stay connected (checked)
    - WAN Ethernet Port: Automatic
    Another question. If I replace my current DSL Router with a wireless router, do I even need the airport base if all I want to do it connect to the internet with the laptop?
    No, the AEBS will no longer be required.

  • I can't access the internet with Firefox on my computer (Windows 7 PC). I have used Firefox as my browser for 1 year but 5 days ago it stopped working even though Internet Explorer worked fine. I can't solve the problem and need some help.Randy Brown

    September 26, 2011
    Dear Mozilla,
    I am having some difficulty accessing the internet with Firefox on one of my PC computers. I normally use Mozilla Firefox as my web browser and google is my homepage and gmail is my email system. The operating system is Windows 7. For over a year this system worked perfectly but a few days ago it stopped working. When I launch Firefox now I get the message that that website (www.google.com) is unavailable. In fact, I can’t access any website and I am blocked from the internet entirely within Firefox. My internet connection is fine because Internet Explorer works fine. I can access google and any other website within that web browser. I have investigated all the security issue I can manage and found no smoking gun. I’ve tried uninstalling and reinstalling Firefox to no avail. Is Windows 7 compromising the effectiveness of Firefox? Any suggestions or other assistance you can offer would be appreciated.
    Sincerely,
    Randy Brown
    [email protected]

    You only have to clone your mac when using certain cable modem.  You don't clone your mac when using dsl.
    Greetings from Northern Ontario, Canada

  • Can't connect macbook pro to internet with airport extreme

    Can't connect macbook pro to internet with airport extreme

    If you have ethernet still on your MBP plug it in by ethernet and tell me if that works.
    Tell me how the Airport is setup.. what broadband modem and router you have.
    What OS on the laptop? Yosemite I guess.. since it is the most troublesome.
    Did it work before whatever change was made? Has it worked in the past? When did it stop and what did you do that coincided with it stopping?
    Upgrade to Yosemite??

  • My imac and ipad2 will not connect to the internet with Windstream using an 2wire DSL modem.

    Help my brand new imac and ipad2 will not connect to the internet with Windstream using an "2WIRE" DSL modem.  Windstream tech service is useless.  i can connect with the built in router through Ethernet or wireless, but still no connecting to internet, help!  windstream said everything is working on their end, yea right.  What i do know is that both the mac and ipad work at other places and can connect with wireless connected to the internet, so i know it's not the apple products. 
    these are brand new machines with lion.
    This is my first mac, so I’m still new to how it works, which is not helping either so a detailed help would be great.  Please help before my wife losses it
    thanks

    There is a 2701HG-B, and a 2701HG-D.  If not labelled on the modem, ask Windstream which one they presently supply or how to tell the difference.
    By the way tell your wife it isn't that bad.  At least you have an ethernet DSL modem.  There were times where DSL modems had RJ-11, USB, and Ethernet, and all three were used to provide access.  At least now only the craziest DSL providers still use those modems.

  • How do I use tether with droid ultra, keep getting message to call verizon. Do Verizon charge or have to somehow change my account?

    How do I use tether with droid ultra, keep getting message to call verizon. Do Verizon charge or have to somehow change my account?

    Verizon Wireless Customer Support wrote:
    Hi there JByrd,
    Let's take a closer look into this. What plan are you currently on? If you are on the More Everything plan, then you shouldn't have to do anything additional. If you are on the Nationwide plan it is an additional $20 a month for 2 GB of data. Let us know what plan you have. Thanks!
    ErinW_VZW
    Follow us on Twitter @VZWSupport
    Hey Erin how about you confirm to Elector and others that you HAVE to pay for tethering on Nationwide plans and that if you are using a 3rd tethering app to bypass paying you are violating the terms of service. They don't seem to believe me.

  • Can no longer connect to internet with wireless router.

    For almost a year I've had a wrt54g ver 6 connected on my computer with my cable modem and my sons computer with the compatible pci card. Everything worked fine until a few days ago, I came home and could not get on the internet with my computer. My son could, but not me. I didn't change anything at all. So I reinstalled the router drivers and I still can't connect to the internet, but now neither can the other computer. What could be the problem?
    michele

    it sounds like you might have to clone the mac address of the computer that was originally connected to the cable modem. clone mac address can be found on setup tab after log into router.

  • Can no longer connect to the internet with the 580...

    Hi, my PC was able to connect to the internet with my 5800 via a USB cable.  Now, I can no longer connect to the internet with the 5800 via a USB cable. 
    I had never tried connecting the computer to the internet with the 5800 via Bluetooth prior to this incident, so I tried that.  Strangely, it works.  
    My question is how come I can no longer use the 5800 via USB as a modem, but how come the 5800 via Bluetooth still works as a working modem?
    Sorry, if my sentences are confusing.  I have a terrible headache at the moment.  While the Bluetooth connection works, I just feel better using the USB connection and knowing that my 5800 has a clean bill of health. 
    BTW, my PC is on Windows 7 Professional at the moment.  I've tried uninstalling the Ovi Suite and reinstalling it, but that didn't work.  I've also tried using PC suite instead of the Ovi Suite but that didn't work either.  What other options do I have, beside hard resetting the phone?  Thanks in advance.        
    Edit: BTW, the message shown when I tried to connect to the internet with the 5800 USB modem was "failed to establish a network connection". 
    Solved!
    Go to Solution.

    Hi,
    I am so  much tierd by trying to connect my phone to pc.
    I have nokia 5800,and I used to connect my phone to PC by USB cable.
    But from last 5 days I could not able to connect it.
    The problem is that,
    when I connect phone to pc,notification comes up that phone connected via ovi suit,but within  a minute or 2,
    "porable device" icon disappears from the task bar in the right hand corner,so connection could not proceed further.
    Please help me in this asap.
    I had tried following already:
    1.format my PC
    2.Installed new ovi suit
    now please give me a proper solution on that.
    thank you.

Maybe you are looking for

  • How to create schedule job and event trigger in XI to start a ABAP program?

    Dear All: Here are what i need to do: 1.To run a ABAP program to start an XI scenario per hour. 2.To run a ABAP program to start an XI scenario per day at 6 PM. 3.To run a ABAP program used event trigger to make sure that XI scenario has finished the

  • Transferring music from iPhone to MacBook

    I have recently downloaded some new albums on my iPhone, however when I tried to transfer them to my MacBook there was a problem with my internet connection and as a result a majority of the songs haven't transferred. At the moment all of the songs t

  • Storing video on Time capsule and ATV and not on computer

    I would like to build my video library and not store it on my IMAC 24 When I back it up and delete it I also loose it from ATV Then I have to restore to watch it Is there any way around this So much storage on the ATV and Time Capsule Why use the com

  • Critical Error: An unhandled error has occurred. Please contact your system administrator.

    Hi all, Does anyone have any idea what the following error relates to? "Critical Error: An unhandled error has occurred. Please contact your system administrator. Debug information: System.IO.FileNotFoundException; Could not load file or assembly 'Mi

  • Why doesn’t the MOD/PLSQL do this?

    When using database authentication the users of my htmlDB applications all have an actual Oracle Database account. The passwords are set to “Expire” every X number of days and all that stuff. When one of my users lets their password expire instead of