No loudspeaker audio after iphone4 screen replacement - help please

Hi All
I recently replaced the damaged screen of an iPhone4, when it all went back together everything worked fine except for problems with the loudspeaker, which worked perfectly before i started working on it. It is strange though that it will play ring tones perfectly well but no music, video, you tube etc
Tested speaker by changing ring tone - could hear through loudspeaker ok.
I am unable to increase (or decrease) the sound bar using the side control buttons (though could when testing with ringtones)
When making a call, switching to speaker works fine.
Occasionally hear the first two screen clicks when entering lock code.
have checked mute isn't switched on.
Works fine through headphones.
Have checked all settings regarding to the sound and all are set as expected.
Have cleaned all contacts with acetone
Have cleaned speakers with dry brush and air spray.
Have tried changing the speaker unit with no change (though i didn't think it would make any difference as the call on speaker worked)
This is now driving me nuts and i was only doing a pal a favour, and could really do without having to try and explain this to him. So any tips/advise or even guesses would be much appreciated.
Thanks
Andy

thats strange that sounds word on certain apps but not on others .... did u happen to try a phone reset // by holding power and home buttons until the device resets and you see the apple logo?

Similar Messages

  • Only hear 8 mins of audio after dvd being burned. help please

    i keep trying to burn an avi file to idvd, but once its burned only the first 8 minutes of audio can be heard after that video looks fine but it becomes a silent film, i called apple and they said to go to advanced and click on delete encoded assets and that should fix the problem, but it didint. Has anyone had this problem and if so did you find a way to fix it?
    id appreciate any help!
    Thanks in advance

    There's a known issue with 12 bit audio and iDVD. But its issue is syncing when encoded. It's unlikely that's the issue but it might. That's out of my area. See these topics: Re: Audio not in sync, Re: Audio sync problem when burning to DVD and So many audio problems.
    They might have a suggestion you can try. Have you tried the disk image route yet?

  • I opened my iPod Touch up to fix my home button. When i closed it back up it had a white screen. I tried pressing lock and home button for 10 seconds and it worked but while i'm using it it goes white with lines on the screen. Help please

    I opened my iPod Touch up to fix my home button. When i closed it back up it had a white screen. I tried pressing lock and home button for 10 seconds and it worked but while i'm using it it goes white with lines on the screen. Help please. This has been happening for a while and i've tried everything but it doesn't work.

    Try:
    fix for Home button
    iPhone Home Button Not Working or Unresponsive? Try This Fix
    - If you have iOS 5 and later you can turn on Assistive Touch it add the Home and other buttons to the iPods screen. Settings>General>Accessibility>Assistive Touch
    - If not under warranty Apple will exchange your iPod for a refurbished one for:
    Apple - Support - iPod - Repair pricing
    You can do it an an Apple store by:
    Apple Retail Store - Genius Bar
    or sent it in to Apple. See:
    Apple - Support - iPod - Service FAQ
    - There are third-party places like the following that will repair the Home button. Google for more.
    iPhone Repair, Service & Parts: iPod Touch, iPad, MacBook Pro Screens

  • Wireless stopped working after blue screen crash. Please help

    Hi am desperate
    I was working on vista doing some graphic job when suddenly the screen turned blue with some message and a count down like thing. After a while vista rebooted fine but since then my wireless is not working anymore.
    I checked my device manager and everything is fine over there, driver installed correctly. But when i try to click on the power on button nothing happens and its not connecting or detecting to any wireless network.
    Then i try to uninstall the device from device manager, as soon as the uninstallation was done, vista installed it back. I checked the power button again and it worked this time. The window opened up and i could see the avaible networks to connect to. As soon as i clicked on any one of them. Some service crashed and i got this
    Problem signature:
      Problem Event Name:    APPCRASH
      Application Name:    svchost.exe_PcaSvc
      Application Version:    6.0.6000.16386
      Application Timestamp:    4549adc4
      Fault Module Name:    StackHash_883e
      Fault Module Version:    0.0.0.0
      Fault Module Timestamp:    00000000
      Exception Code:    c0000005
      Exception Offset:    77e48a32
      OS Version:    6.0.6000.2.0.0.768.3
      Locale ID:    2057
      Additional Information 1:    883e
      Additional Information 2:    949a7a0b47e310a64b136de1ad2bba33
      Additional Information 3:    3ead
      Additional Information 4:    eb840ca556c23fbe49b8bbf96ad42865
    What i noticed is that the MAC address of the card was something different before the crash and after the crash its just FF:FF:FF.....
    The card is physically connected to the PC i my guess is that is fine.
    Can anyone help please?
    Here is a preview of my desktop. Hope someone can help
    Now when i click on the mobility center in the control panel i get the following error
     Problem signature:
      Problem Event Name:    APPCRASH
      Application Name:    mblctr.exe
      Application Version:    6.0.6001.18000
      Application Timestamp:    47919f54
      Fault Module Name:    ntdll.dll
      Fault Module Version:    6.0.6001.18000
      Fault Module Timestamp:    4791a7a6
      Exception Code:    c000007b
      Exception Offset:    00009cac
      OS Version:    6.0.6001.2.1.0.768.3
      Locale ID:    2057
      Additional Information 1:    9d13
      Additional Information 2:    1abee00edb3fc1158f9ad6f44f0f6be8
      Additional Information 3:    9d13
      Additional Information 4:    1abee00edb3fc1158f9ad6f44f0f6be8
    Read our privacy statement:
      http://go.microsoft.com/fwlink/?linkid=50163&clcid=0x0409

    The laptop came with software to make a Recovery Disc set. If you did not make it you can order a set from HP. Usually around $16 for Windows 7 media. https://h10025.www1.hp.com/ewfrf/wc/mediaOrder?cc=us&lc=en&productOid=5112032&softwareitem=659152-001 Some are reporting trouble using the ordering process. If you can't order there fill out the form on this page for more help. https://support.hp.com/us-en/contact-hp/product/HP-Pavilion-g6-1b00-Notebook-PC-series/5082228/model/5112032

  • Ipod touch 4th generation camera doesn't work after smashed screen replacement

    I have an ipod touch 4th generation that i smashed to screen with a torch, i got the screen replaced however my camera shutter will NOT open at all, i can go into camera roll and everything BUT the shutter wont open and the slide to go from camera to video just blinks a few times. Ive tried everything from turning it off and on(note my off/top button doesn't work) I had problems with the camera before i had the screen replaced but now it doesn't work at all. And will resetting and/or restarting it through iTunes delete ANY of the conent i have on my Ipod?
    Any help much appreciated as i can NOT afford to get it fixed at Apple!!

    If you restored to factory settings/new iPod and still have the problem that indicates a hardware problem.
    In that case take it back to the people who replaced the screen. They likely messed something up unless what broke the screen and broke the camera.

  • After effects and photoshop ,,,help please

    hi all
    can anybody help please.
    ive been making a short film with my son and putting some basic effects in, just for a laugh.
    i noticed an effect on ADOBE TV that was done by Gareth Edwards in his movie MONSTERS which i thought would be good to try out in my film but i carnt get it right,,
    here is the link to that effect...            http://tv.adobe.com/watch/customer-stories-video-film-and-audio/monsters/
    its the effect where he changes the menu board in a cafe to one of his infected area signs, he allso changes a few other signs.
    in the video he say that he exports a still frame from after effects into photoshop and puts on his image {with a few tweaks her and there}, when hes got it ok in photoshop ,it some how updates in after effects??
    can any please help ,thank you

    It's a simplified explanation of the process.  He left out explanations of motion tracking and perspective matching that were most certainly required for the shot being discussed.
    If you are doing the same process to a static, locked off shot, with no foreground objects passing in front of your sign, it would be very possible to create a single frame in Photoshop and just layer it over your scene in AE.  But once the camera moves, you will need to understand Motion Tracking.  If objects pass in front of the replaced component, you will need to understand Masking.

  • How do I retrieve photos/data etc. from my iPhone 4 before a completely erasing restore! It'stuck on a "connect to iTunes" to restore screen!  Help please!!!

    I connected my iPhone 4 to my PC to sync all my new info to iTunes/PC, but it said it was not able to recognize it and needs to do a complete restore!  How do I retrieve photos from my iPhone 4 before a complete restore! It'stuck on a "connect to iTunes" to restore screen and won't do anything else!  I tried rebooting the phone (holding the top button and the home button and the SAME "connect to iTunes" screen comes up.  If I restore, I will lose ALL my unsynced photos, apps, and data from the past week (INCLUDING pics from a concert WITH band members!) Help please!  MAYDAY!  My prior backup does NOT contain these photos/apps/data! Ahh!!!!

    I am having the same problems as this person. I see that someone said there is no way to retrieve the pictures once it gets stuck in recovery mode.
    Then further along someone said that there are data retrieval methods except they have something to do with jail breaking a phone.
    My phone is already jail broken. It was kind of a gift from the company I work for- it was a fellow employees before. He jail broke it and then it was given to me. After I got it I activated the 4 and tried to back up everything. It didn't work and "Springboard" forced the phone into safety mode. So I could use it with the old dude's apps and my contacts. I made the mistake of using the phone for wedding dress shopping with a friend. I took tons of pictures.
    After this I found out the messages I was seeing meant it was jail broken. At&t said to force restore the phone - iTunes wouldn't recognize it in safety mode. I'm an idiot and didn't realize what this meant for my pictures. It didn't work (error 1611) - thankfully. Now it is stuck in recovery mode (iTunes icon and USB cable picture).
    Can I access that media in any way? It never suceeded restoring itself so is it still there? The phone is jail broken already so is there a method I can use?

  • LR6 freezing on full screen. Help please?

    I have just got LR6 (WINDOWS 64x). When I use the Full Screen (or F key shortcut) I cannot exit the full screen without using Task Manager (Ctrl/Alt/Delete)and ending task (ie, LR). When I do this LR closes without saving, or having the option to save, the catalogue. This is most frustrating and time wasting. Also now do not have the ability to view images on the full screen. LR6 works OK providing that I don't use the full screen option. I have also noticed that the image processing/loading is noticeably slower. My graphics processor checks out OK. Help please???

    I'm sorry, but I am a bit out of ideas here.
    I suppose the rest of your system like RAM is well enough too.
    Does the Windows event log have any entry after the freeze? Too bad it's not BSOD - that would at least show a hint where the issue might be.
    FWIW, I'd try with an older graphic card driver as well - you never know.

  • N97 screen cable =( help please!

    my n97 that i absolutely LOVE wouldnt start the other day;
    i figured it was coz it ran out of battery
    after charging it and turning it back on, 
    the screen wouldnt turn on?
    everything else was fine;
    it made the nokia sound at the start
    and the keys lit up also.
    after looking at it;
    i realised that the screen cable;
    behind the screen; had snapped?!
    is there anything i can do to fix this?
    also;
    if i have to take it to a store to get fixed..
    how much and how long will it take?!
    -i'd appreciate any help i can get. =)

    If its hardware, I would definitely recommend that you take it to Nokia care center. I dont think that it is not covered by warranty since I cannot think of a situation normally when the cable would just snap.
    If you find my post helpful please click the green star on the left under the avatar. Thanks.

  • HP Pavilion a6000 desktop with Vista black screen - need help please!

    I have an HP Pavilion a6000 desktop with Vista.  Yesterday it was working fine and today we have the black screen that reads: 
    Award BootBlock BIOS v1.0
    Copyright (c) 2000, Award Software, Inc.
    BIOS ROM checksum error
    Detecting IDE ATAPI device...
    Found CDROM, try to boot from it...Fail
    Detecting IDE ATAPI device...
    Detecting IDE ATAPI device...
    Detecting floppy drive A media...
    Drive A error.  System halt
    I am not a techie, but looked at online forums and have tried f10 at startup with no change to the screen other than it stops after the first four lines and does not try the floppy drive.  I also pulled out the round battery, waited and then reintstalled.  Same problem.  
    Also, computer emits a single, repeating beep after startup.
    HELP!

    jjeahall
    I saw your post and wanted to comment. I'm not an expert on these types of situations but did some digging around and found the following at Tips4PC.com.... read below
    "There are two types of computer black screens that can appear in Windows. One where the computer will not boot up but you have a beep sequence sounding to let you know what the problem could be, and the other has nothing at all. No beeps, no cursor, no logo screen, and no choice to boot to safe mode or access the bios.
    If your computer will not boot up and you get a beep sequence, I am not saying it is good news, however it is a step in the right direction towards solving this problem. This is a message from your computer that can be understood by looking up your bios (the brand) beep code. For example you may have an Award Bios, Ami Bios, Phoenix BIOS, Compaq, Dell, or Acer Bios. This list goes on and on.  You can search for Bios beep codes in Google. Here is an example of results in Google search"
    Link
    Also  I went into the Troubleshooting Guide for the A6000  and found the following information.  You need to use F11 for recovery. See below
    Starting System Recovery from system startup
    1
    Turn off the computer. If necessary, press and hold the On button until the computer
    turns off.
    2
    Remove the HP Personal Media Drive if your computer includes one. Disconnect all
    peripheral devices from the computer except the monitor, the keyboard, and the
    mouse.
    3
    Press the On button to turn on the computer.
    4
    During the startup, do the following to enter the Recovery Manager program:
    When the blue screen with the HP Invent logo appears, press the F11 key on the
    keyboard. (You have only a few seconds to press the F11 key before the normal
    startup process continues.)
    5
    The computer starts the Recovery Manager program; wait for the onscreen instructions
    to display, and then follow those instructions.
    6
    Complete the computer startup, finish the registration process, and wait until you see
    the desktop. Then, turn off the computer, reconnect all peripheral devices, and turn on
    the computer.
    I am an HP employee.
    Regards,
    Cooper56
    If you’ve found this information helpful, please make it easier for others who might be experiencing a similar type issue by marking my answer as “Accept as Solution” .
    ***Of course you can also Click on “Kudos” STAR to say thanks!***
    I work for HP. When your problem has been solved, accept the solution by clicking the "Accept as Solution" button to help other members in the future!

  • Z10 won't complete setup after device software update, help please.

    Help please, cannot complete phone setup ater performing software update using Blackberry Link.
    Sequence of events;-
    Phone recognised by Blackberry Link.
    Reload device software selected - updated version 10.0.10.90 available.
    Get update - software appears to load correctly then Z10 unplugged.
    Phone reboots, Welcome to Blackberry, English(UK) ticked, swupe left.
    No SIM card available, swipe to WI-Fi.
    Password entered for home network and confirmation screen shows connected.
    Agreement Screen - Country changed to United Kingdom(English),
    at bottom of screen under I agree to the Blackberry SLA....
    the 'I Agree' and 'I Do Not Agree'  buttons can not be selected and
    after a short delay Unable to connect screen appears.
    Pressing 'Settings' goes back to Wi-Fi Networks page with
    confirmation that connection is good and round we go again.
    Having performed software update several times as above and also from
    www.BlackBerry.com/updates by following forum posting at
    http://supportforums.blackberry.com/t5/General-Bla​ckBerry-10-Smartphone/How-
    to-Reload-your-Blackberry10-OS/td-p/2187545
    and getting the same result each time I would appreciate help to resolve this issue.
    Solved!
    Go to Solution.

    Try finding a different open free Wifi hotspot to perform the setup.
    It sounds like the device is never connecting to your WiFi to complete the setup.
    1. If any post helps you please click the below the post(s) that helped you.
    2. Please resolve your thread by marking the post "Solution?" which solved it for you!
    3. Install free BlackBerry Protect today for backups of contacts and data.
    4. Guide to Unlocking your BlackBerry & Unlock Codes
    Join our BBM Channels (Beta)
    BlackBerry Support Forums Channel
    PIN: C0001B7B4   Display/Scan Bar Code
    Knowledge Base Updates
    PIN: C0005A9AA   Display/Scan Bar Code

  • Can't get into IPad 2 after latest update.  HELP, PLEASE!??

    I made the mistake of updating my IPad 2 to the latest IOS7.  Now I cannot get into it.  When I turn it on, it says 'hello' and to swipe to set up the new update.  Sometimes the swipe brings up a new screen; sometimes it just scrolls through several languages.  Sometimes it asks for my Apple ID and gets as far as "updating ICloud."  It NEVER finishes updating ICloud! 
    I cannot reach my apps or a normal looking screen.  Can someone help, please?  Is there any way to get this update to work or to UNDO the update?  I'll be grateful if you can help.......  Thank you so much!
    Virginia

    1. Slide to set up
    2. Select language
    3. Select country/region
    4. Choose Wi-Fi Network
    5. Enable/Disable Location Service
    6. Enter Apple ID and Password
    7. (a) Set Up as New (b) Restore from iCloud Backup (c) Restore from iTune Backup
    8. Terms and Conditions
    9. Use iCloud/Don't use iCloud
    10. Create/Don't create Passcode
    11. Diagnostics
    12. Welcome to iPad

  • Broken Bonjour with Canon MF4350d after 10.6 upgrade - Help Please.

    I have been using a Canon 4350d with no problems with 10.5.8 - including Printer Sharing (Bonjour). Now, after updating to 10.6 (now 10.6.2) I can still print fine, but I have lost all Printer Sharing. All settings appear to be right, and my other macs appear to be printing through the one connected via USB to the printer, but it never goes through. HELP Please. Thank you.

    According to the UFR2 User Guide on page 2-8, the driver can be removed from the Mac by trashing the following folders. Note that you should delete the print queue first, by opening Print & Fax, selecting the MF model in the Printers list and pressing the minus button.
    System Volume > Library > Printers > Canon > UFR2
    System Volume > Library > Launch Agents > jp.co.canon.UFR2.BG.plist
    System Volume > Library > Printers > PPDs > Contents > Resources > en.lproj > CNTD**Z*2.ppd.gz
    (where * indicates the printer model and 2 indicates the language of driver used)
    With these files removed you can then empty the trash, although you may have to open Activity Monitor and stop the 'UFR II Backgrounder' service before you are able to remove all the files from the trash.
    With the v2.10 driver removed you are ready to add another driver. However you need to be aware that the v1.80 driver cannot be used on 10.6. If you were using it previously then it would suggest that the 10.6 Mac was an upgrade from 10.5 rather than a clean 10.6 install. On a clean 10.6 Mac, then v1.80 driver will not operate correctly.
    What you may be able to do is have the v1.80 driver installed on a Mac running Leopard and shared. You may then be able to use the v2.10 driver on the Snow Leopard Mac's to print to the Leopard share using the v1.80 driver. Note that I haven't tried this so I cannot say if this will work for you. Personally I always ensure I get a printer with Ethernet or wireless support so that I can avoid printer sharing...

  • Iphone 4s shuts off when it has a full battery and says its dead. This started happening right after a screen replacement.

    I have an iphone 4s and ever since the screen was replaced. It has been shutting down with a full battery saying its dead. Can someone help me?

    Hi Dcp019,
    There's a section in this article for power issues like unexpected power off.
    iPhone: Hardware troubleshooting
    http://support.apple.com/kb/ts2802
    If the issue started after a repair however, you may want to check with them about the repair.
    Best regards,
    Nubz

  • After 10.5.2 install stuck at the login screen.  Help please!

    Hi all,
    After installing 10.5.2 my computer rebooted to the login screen, but no matter what account I select (I have 3) it goes to a blue screen for a few seconds and then right back to the login screen. I've tried booting in safe mode and also resetting the PRAM. I've been reading this forum, but don't seem to see anyone else having this same exact problems.
    Any suggestions?

    I have had problems after the 10.5.2 update. I ended up with a frozen computer - unable to restart or shut down etc. Also ended up at one stage with Set Up Assistant screen. With the help of a computer savvy friend, at least I am able to use my computer again.
    It appears the actual download did happen but it did not install and the computer tells me I need to "re-start". When I did this, window appeared on plain blue screen saying it was installing software but absolutely nothing happened - no blue scrolling bar etc.
    My iMac computer is still under Apple Care Plan and technician told me they are many problems surfacing across the various machines with this upgrade. He has asked me to delay updating the software and to ring back in a couple of days because their technicians are currently working on the problem and he hopes for an answer soon.

Maybe you are looking for