No network connection after windows 10 install

No internet connection after windows 10 install- laptop wont recognize any wi-fi networks- repair option on MY ATT has no option for windows 10 system

Hi,
Sorry about that. One other thing to try is to try this in the command prompt:
Start - All Programs - Accessories and right click on Command Prompt, select "Run as Administrator" to open a command prompt. [For Windows 8 or 10: <Windows Logo> + x - Command Prompt(Admin)]
Reset WINSOCK entries to installation defaults: netsh winsock reset catalog
Reset IPv4 TCP/IP stack to installation defaults. netsh int ipv4 reset reset.log
Reset IPv6 TCP/IP stack to installation defaults. netsh int ipv6 reset reset.log
Reboot the machine
If still having issues, you may need to uninstall your network adapter and install it again.
-ATTU-verseCare

Similar Messages

FP1600 loses network connection after a few hours

My FP1600 loses its network connection after a few hours. It is part number 185690C-01, with firmware 4.11. I am running FieldPoint Explorer version 3.0.1 and LabView 6.1 from Windows XP Professional. I set it up, and everything runs fine for 4 hours or more. I do not have the network watchdog enabled, and the FP1600 is in constant communication with the host computer in any case. Sometime in the middle of the night the communication is lost. The FP1600 link light
is on, and it is still receiving packets, but it will not respond to a ping or any other communications. Only a power cycle brings it back. The FP1600 is sitting right next to the host computer, both attached to the same network switch. There is no interruptio
n of network services to the two.

Hi Heinz,
We are also trying to troubleshoot this same problem (Intermitten network connection loss with FP1600 Ethernet Module - Error code "33163", Error Message - "FP1600 Connection to module has been lost."). We have checked other possible causes for this sort of behaviour. Including independent assessment of netowork availability at the time of error reporting, connecting dedicated power supply to the FP1600 module, temperature of cabinet housing the module (which is between 10 and 50 deg C), disconnecting sensors connected to various I/O modules connected to this module, increasing duration of parameter "time out" (the time module will wait before reporting an error if it can not access network). However, none of the above resolved the intermittent and random network loss errors.
The MAX version is 3.0.2, and the firmware on the module is 4.17, Labview version is 7.0 and the Operating System is windows NT.
I was wondering is there any information about this problem from any user or NI recently. The only solution looking in to this discussion forum seems to be replacing the module.
MehulMessage Edited by MPatel on 02-28-2005 08:16 PM

My Mac Pro loses network connection after wake from sleep since Yosemite upgrade.

Mac Pro loses network connection after wake from sleep since Yosemite upgrade. Any one have this issue as well. And is there a work around?

Wi-Fi?
Wi-FI connection drops
Wi-Fi Problems in OS X Yosemite
Wi-Fi Problems in OS X Yosemite (2)
Wireless Diagnostics
Also try turning off Bluetooth.
Troubleshooting Wi-Fi issues in OS X
Wireless Connection Problems - Fix
Wireless Connection Problems - Fix (2)
Wireless Connection Problems - Fix (3)
Wireless Connection Problems - Fix (4)

Apple TV2 can't find my network connection after recent update?

Why can't my Apple TV2 can't find my network connection after recent update?

I had to update the software on my Airport Extreme then reset my apple tv and that resolved the issue for me.

I loose my home network connectivity after my iMac is awaken. This began after I upgraded to Lion. Is there a fix to this problem?

I loose my home network connectivity after my iMac is awaken. This began after I upgraded to Lion. Is there a fix to this problem?

see if this article helps: http://osxdaily.com/2011/11/06/lion-wi-fi-problems-solution-mac/?utm_source=feed burner&utm_medium=feed&utm_campaign=Feed%3A+osxdaily+%28OS+X+Daily%29&utm_conten t=FaceBook

Windows 7 Pro not finding network connections after boot camp installation. Is there something special we have to do to get the network (wired and wireless) set up?

Any suggestions for getting the network connections working on Windows 7 Pro running on a Mac Min with OSX Lion?

tim-bob wrote:
Any suggestions for getting the network connections working on Windows 7 Pro running on a Mac Min with OSX Lion?
If you haven't yet installed the Windows Support Software, that's probably why, so install it now.

Cannot log into windows network account after Bootcamp install

Hi All,
I have a 27" Intel i3 iMac with Mountain Lion 10.8.7. Its connected to a windows server. To access my account on the Mac I log in with a username and password. Yesterday I had Bootcamp with a 32bit version of Windows installed. After the Windows was installed successfully, my 'Helpdesk' had to remote access in and run patches on the windows installation. All good so far.
I tried to log into my mac account this morning with username and password. There is a little red light beside your username. I had no luck what so ever. My account has vanished of my mac. I could 'locally' log in under the adminstrator account. There was no sign of my account in the users & groups.
I had back upped my files except for the download folder. I eventually found the download folder and was able to back that up.
please please can someone explain what has happened here.
My IT guy has no Apple trianing and wants to remove my mac and replace it with the a PC because they support them. I feel it was a bad bootcamp installtion done by the IT tech, he did mention that he installed a 32 bit windows instead of a 64 bit. Its lack of trainign and understanding that has caused this.
I am trying to make an argument to say that it was simplay a bad Bootcamp installtion and try and find simliar cases to back it up.
Please help

Mac partition was still there as I was able to log into the Administrator account on the mac. But when I went into users and groups there was no sign of my account. I'll agree it was a bad install, jsut need to explain it and back it up so that I can make that argument.
thansk

Photosmart 6180 All-in-One Wireless Connection After Windows 7 Laptop Added to Network

I replaced a broken Vista laptop with a new Windows 7 64-bit laptop. After I installed my Photosmart 6180 All-in-One, the printer stopped working correctly when we try to connect to it wirelessly.
I followed all the directions HP provides for updating the printer software and drivers for Windows 7.
We've tried all the suggestions for resetting the printer that we can find on the HP forums.
The printer works properly when connected via USB cable to a Vista laptop.
I was not able to get the printer to work via USB cable connected to the Windows 7 laptop.
When we try to connect via the wireless signal, regardless of Vista or Windows 7, the printer goes into an endless initialization loop.
We need to determine whether achieving a wireless connection is hopeless. If it is not, we need step-by-step instructions on how to resolve the issue.
The security system for the printer is WEP. We connect through a wireless router provided by Verizon FIOS.
Many thanks in advance for your help.

Some of HP's printers do not support WEP shared. If you are using WEP shared this could be the problem. I would suggest turning off the WEP security temporarily to see if that fixes the issue. If it does then you can look at changing the security to WEP Open system authentication.
Mike
Say "Thanks" by clicking the Kudos Star in the post that helped you.
I am an HP employee.

No network connection after install on a VirtualBox VM

Hey guys, I am a relative newb to Arch, and linux in general for that matter. I'm working on a project with pogo plugs and Arch seems to be the best linux solution for those at the moment so I figured it would do me some good to get it running on my desktop so I can become more familiar with it.
I'm attempting to install it on a VirtualBox vm following the beginners install guide. I get all the way through the install and reboot into my shiny new OS, but have run into the issue where I can't do any further package updates as I have lost my network connection. The beginners guide specifies a way to configure this so it it is persistent once the install is done.
I can issue the systemctl enable "dhcpcd@<interface>.service" command with my interface as eth0 (verified by ip link) "[email protected]", but once I reboot into the fresh install ip link tells me my interface is actually enp0s3. If I rerun the dhcp enable command again with enp0s3 as the interface it executes without error, but I still do not have network.
I tried using ifplugd during the install process during one of my go-arounds, but ifplugd was not able to install as none of the files appear to be available, perhaps that server is down?
Can anyone shed some light on what I might be doing wrong? I'm guessing it's something very simple that I am missing, hopefully someone here can catch it.

I was stuck at this problem, as in topic header. I looked at this post, thought that finally I found the solution(was referring to one more post). Then I tried following steps as mentioned in #3. OMG, I tried it for more than hour, couldn't get it working. Then i get one hint, i.e, the interface name is not enps03 but its enp0s3 ... Okay, again i tried, but still it did not work... this time i was little more cautious, so after few attempts, looked at my command, i had been typing [email protected], I don't know why such confusing naming conventions are followed, there are two files under /lib/systemd/system/ that are like dhcpd.* .. but this one particular file is dhcpcd@.*... well.. that's it. I just had to laugh at myself.

MBP takes long time to restore wired network connection after wake-up

Hello...
My Mid-2010 MBP (MacBookPro6,2) has been experiencing this problem recently -- Whenever I wake up the computer from sleep, it needs approximately 10 seconds to restore its wired network connection. I know there are other annoying connection issues with MBP's WiFi/AirPort out there, but I'm talking about the wired connection here.
Maybe some don't even think this slowness is a problem at all, but this laptop used to be network-ready right after wake-up until 3~4 months ago. That was around the time when I upgraded to SSD and changed some settings via pmset, not sure if that's the culprit. It is now running OS X 10.8.5 and its pmset settings are:
Battery Power:
lidwake              1
ttyskeepawake        1
hibernatemode        3
gpuswitch            2
hibernatefile        /var/vm/sleepimage
displaysleep         2
sleep                15
acwake               0
halfdim              1
sms                  0
lessbright           1
disksleep            10
AC Power:
lidwake              1
ttyskeepawake        1
hibernatemode        0
gpuswitch            2
hibernatefile        /var/vm/sleepimage
womp                 1
displaysleep         10
networkoversleep     0
sleep                60
acwake               0
halfdim              1
sms                  0
disksleep            0
I'd appreciate help of any kind
Thanks,
zuoy

Maybe try this, i am not sure that it will resolve the problem, but it is worth trying anyways.
http://social.technet.microsoft.com/Forums/en-US/w7itpronetworking/thread/eef49e64-157c-4082-8e80-52e48309691f
Hi All,
I've seen this problem multiple times, especially with Windows 7 64-bit versions and Enterprise edition. The source of the problem appears to be the Bonjour service that is installed in the background and set to "Automatic" when installing certain 3rd
party applications. Apple applications like iTunes and Adobe applications like Acrobat Professional and Creative Suites have been known to cause this problem. I've also seen virtualization software like VMWare and VirtualBox cause similar issues
with network adapters.
The solution in most of the cases I've come across has been to stop and disable the Bonjour service. The Bonjour service also masquerades as a service with a name of the format "##Id_String1.6844F930_blahblahblah". Here's how to disable this service
in Windows 7:
Right-Click on Computer > Select 'Manage'
Expand the 'Services and Applications' section in the bottom of the Left-Nav dialog and Select 'Services'
Sort the Services list by name and look for either "Bonjour" or the "##Id_String..." name mentioned above
Right-Click on the service and select 'Properties'
Click the 'Stop' button to stop the service
Select 'Disabled' from the 'Startup type' drop down list
Click 'Apply' and then 'OK'
Reboot your machine and see if the "Multiple Networks" issue is resolved. If so, you should have internet connectivity again.
Hope this helps.
cheers,
Aaron

2008 r2 hyper-v guest with static IP always looses network connectivity after every restart - no problem with DHCP

Hello,
We are running 2008 R2 domain with one physical DC and other running in VM on Hyper-V host (2008 R2 Standard). The host has 4 NICs and is configured to use one physical NIC for itself (management) and the hyper-v guest is configured to use another dedicated/physical
NIC (through microsoft virtual switch) just for itself.
I noticed that after setting the hyper-v guest with a static IP address all works fine only until guest restart. When the guest boots up the IP address is still configured correctly in IPv4 properties, but there is no network connectivity at all and in fact
the guest shows running APIPA config in ipconfig /all output. That situation continues until I remove the virtual NIC from hyper-v guest, remove the virtual switch from dedicated NIC on host and then reconfigure it (using same settings as they were). very
annoying.
For time being I switched the virtual DC (problematic hyper-v guest) to a DHCP IP and configured DHCP server (running on physical DC machine, not on hyper-v host) to store a reservation for the hyper-v guest so it always gets the same "static"
IP configuration.
Is there some kind of a problem/bug with using static IP on (2008 R2) hyper-v guests? is there a hotfix for static IP config in hyper-v guest environment?
both 2008 R2 OSes (host and guest) are up to date with all updates (synced with Microsoft, not WSUS).

OK, I'm not at the office now, but took my time to test out the restart scenarios on problematic virtual guest remotely.
No dice, same as it was, everything works fine after guest has IP configured in DHCP mode (IP reservation of 192.168.1.5 for specific MAC address) and it doesn't work after restart in static IP mode (same address, works before restart of guest).
I also took "arp -a" outputs at each step from host server and that was always saying there is only a single host (192.168.1.5 = VDC = problematic virtual guest) assigned to that IP address and always with same MAC, so that pretty much rules out
ARP/MAC troubles and no issues with switches/routers getting spoofed. Problem is most likely with the virtual guest (WS2008R2) or within the host running same OS.
Here are outputs:
A) VDC has IP configured in DHCP mode - always same, survives through restart (all works)
Ethernet adapter Local Area Connection:
Connection-specific DNS Suffix . : CD.lan
Description . . . . . . . . . . . : Microsoft Virtual Machine Bus Network Adapter
Physical Address. . . . . . . . . : 00-15-5D-01-D3-00
DHCP Enabled. . . . . . . . . . . : Yes
Autoconfiguration Enabled . . . . : Yes
Link-local IPv6 Address . . . . . : fe80::b9af:6679:3142:8799%13(Preferred)
IPv4 Address. . . . . . . . . . . : 192.168.1.5(Preferred)
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Lease Obtained. . . . . . . . . . : Thursday, January 30, 2014 5:34:48 PM
Lease Expires . . . . . . . . . . : Friday, February 07, 2014 5:35:26 PM
Default Gateway . . . . . . . . . : 192.168.1.254
DHCP Server . . . . . . . . . . . : 192.168.4.5
DHCPv6 IAID . . . . . . . . . . . : 268440925
DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-1A-6F-5F-C2-00-15-5D-01-D3-00
DNS Servers . . . . . . . . . . . : 192.168.1.5
192.168.4.5
NetBIOS over Tcpip. . . . . . . . : Enabled
ARP -a output from host server at that time:
Interface: 192.168.1.4 --- 0xc
Internet Address Physical Address Type
192.168.1.5 00-15-5d-01-d3-00 dynamic
B) VDC has IP configured in static mode - BEFORE RESTART (all works)
Ethernet adapter Local Area Connection:
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Microsoft Virtual Machine Bus Network Adapter
Physical Address. . . . . . . . . : 00-15-5D-01-D3-00
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes
Link-local IPv6 Address . . . . . : fe80::b9af:6679:3142:8799%13(Preferred)
IPv4 Address. . . . . . . . . . . : 192.168.1.5(Preferred)
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Default Gateway . . . . . . . . . : 192.168.1.254
DHCPv6 IAID . . . . . . . . . . . : 268440925
DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-1A-6F-5F-C2-00-15-5D-01-D3-00
DNS Servers . . . . . . . . . . . : 192.168.1.5
192.168.4.5
NetBIOS over Tcpip. . . . . . . . : Enabled
ARP -a output from host server at that time:
Interface: 192.168.1.4 --- 0xc
Internet Address Physical Address Type
192.168.1.5 00-15-5d-01-d3-00 dynamic
C) VDC has the same IP configured in static mode - AFTER RESTART (no more network connectivity at all, LAN in Public zone)
Windows IP Configuration
Host Name . . . . . . . . . . . . : VDC
Primary Dns Suffix . . . . . . . : CD.lan
Node Type . . . . . . . . . . . . : Hybrid
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No
DNS Suffix Search List. . . . . . : CD.lan
Ethernet adapter Local Area Connection:
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Microsoft Virtual Machine Bus Network Adapter
Physical Address. . . . . . . . . : 00-15-5D-01-D3-00
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes
Link-local IPv6 Address . . . . . : fe80::b9af:6679:3142:8799%13(Preferred)
Autoconfiguration IPv4 Address. . : 169.254.135.153(Preferred)
Subnet Mask . . . . . . . . . . . : 255.255.0.0
Default Gateway . . . . . . . . . : 192.168.1.254
DHCPv6 IAID . . . . . . . . . . . : 268440925
DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-1A-6F-5F-C2-00-15-5D-01-D3-00
DNS Servers . . . . . . . . . . . : 192.168.1.5
192.168.4.5
NetBIOS over Tcpip. . . . . . . . : Enabled
ARP -a output from host server at that time:
Interface: 192.168.1.4 --- 0xc
Internet Address Physical Address Type
192.168.1.5 00-15-5d-01-d3-00 dynamic
Throughout the testing, the hyper-v host IP configuration and IPconfig output was always staying same.
The Network Connection #2 is the only one the host uses (not shared with hyper-v guests).
The Network Connection #4 is assigned to Microsoft Virtual Switch hence why it doesn't show up in results, like below:
Windows IP Configuration
Host Name . . . . . . . . . . . . : HYPER-V
Primary Dns Suffix . . . . . . . : CD.lan
Node Type . . . . . . . . . . . . : Hybrid
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No
DNS Suffix Search List. . . . . . : CD.lan
Ethernet adapter Local Area Connection 3:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : HP Ethernet 1Gb 4-port 331i Adapter #3
Physical Address. . . . . . . . . : 9C-8E-99-52-15-91
DHCP Enabled. . . . . . . . . . . : Yes
Autoconfiguration Enabled . . . . : Yes
Ethernet adapter Local Area Connection 2:
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : HP Ethernet 1Gb 4-port 331i Adapter #2
Physical Address. . . . . . . . . : 9C-8E-99-52-15-90
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes
Link-local IPv6 Address . . . . . : fe80::dc78:8a3b:38a5:7af3%12(Preferred)
IPv4 Address. . . . . . . . . . . : 192.168.1.4(Preferred)
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Default Gateway . . . . . . . . . : 192.168.1.254
DHCPv6 IAID . . . . . . . . . . . : 312250009
DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-1A-67-52-8F-9C-8E-99-52-15-93
DNS Servers . . . . . . . . . . . : 192.168.4.5
192.168.1.5
NetBIOS over Tcpip. . . . . . . . : Enabled
Ethernet adapter Local Area Connection:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : HP Ethernet 1Gb 4-port 331i Adapter
Physical Address. . . . . . . . . : 9C-8E-99-52-15-93
DHCP Enabled. . . . . . . . . . . : Yes
Autoconfiguration Enabled . . . . : Yes
On Monday I will install more test guests in Hyper-V host (WS2008R2), in variety of flavors like 7x64, 8.1x64, ws2012r2, and see if they show similar problems with static IP configuration when utilizing a dedicated NIC from host server.
Don't get me wrong, I can live with virtual DC running on DHCP IP reservation (which is based on MAC), because the virtual DC pretty much requires a physical PDC (hosting also DHCP in my network) to be present for safety reasons ... however I prefer a static
IP configuration on all servers, hence my question and surprise why it doesn't work.

Unreliable Network Connection with Windows

Hi,
I am using a Macbook Pro with Mac OSX Mavericks.
I have shared a few folders on my Macbook over the network so they can be accessed by another computer running Windows 7 Pro. The Macbook is connected to my home network using an ethernet cable via a hub.
I am unable to reliably copy *any* files from Windows to my Macbook.
Any attempt to copy a folder containing more than a few hundred files invariably results in the Macbook's network folder becoming disconnected (and therefore unreadable) briefly, cancelling the whole operation.
This was always pretty unreliable on Mac OSX Mountain Lion, but has since become even worse since I upgraded to Mavericks.
Does anyone else have this problem? How do you reliably share files over your network?

Home Edition or Home Premium?
The Apple SETUP drivers on your OEM DVD (Boot Camp 3.0.x) should enable network and seems that is fine.
The only AV you need, and you do need, is MS Security Essentials. I wouldn't bother with anything else, or any free or commercial suite or firewall.
PCs have had trouble too, with lost connections after resuming from sleep.
Is this wired or wireless?
How about the modem, router, etc. setup and configurations?
Uninstall the device driver and let Windows install its own.
You can always use Device Manager to "rollback" a driver; you have more options and flexible with Windows in that regard than OS X ever had, so you can test and try out different driver. Just look for current network adapter driver. And no, I'd think there is Windows 7 or Windows Vista/7 bundle (installer or zip package).
And if it is the BASIC Windows 7 then I'd also consider upgrade to Home Premium.

[SOLVED] Losing network connection after suspend

Lately I'm having this peculiar problem. When resuming after suspend (specifically, pm-suspend), I have no network connection. I first noticed this on March 31st. The only thing that changed was that I upgraded these packages:
openssl-1.0.1-2-x86_64.pkg.tar.xz
xf86-video-ati-6.14.4-2-x86_64.pkg.tar.xz
lib32-libdrm-2.4.33-1-x86_64.pkg.tar.xz
libnotify-0.7.5-1-x86_64.pkg.tar.xz
xz-5.0.3-2-x86_64.pkg.tar.xz
vim-taglist-45-5-any.pkg.tar.xz
But I'm pretty sure I would have suspended and resumed successfully at least once after that upgrade.
Can anyone suggest what I should look at to try to diagnose this?
Thanks
Last edited by ibrunton (2012-04-06 11:26:03)

Same issue here. Looks like dhcpcd crashes during or after running /usr/lib/dhcpcd/dhcpcd-run-hooks on resume from suspend. I'll try downgrading until this is fixed.
$ uname -s -v -r -m
Linux 3.2.13-1-ARCH #1 SMP PREEMPT Sat Mar 24 09:10:39 CET 2012 x86_64
$ pacman -Qi dhcpcd
Name : dhcpcd
Version : 5.5.5-1
URL : http://roy.marples.name/dhcpcd/
Licenses : BSD
Groups : base
Provides : None
Depends On : glibc sh
Optional Deps : None
Required By : networkmanager
Conflicts With : None
Replaces : None
Installed Size : 256.00 KiB
Packager : Ronald van Haren <[email protected]>
Architecture : x86_64
Build Date : Fri Mar 23 17:25:47 2012
Install Date : Thu Mar 29 23:36:13 2012
Install Reason : Explicitly installed
Install Script : No
Description : RFC2131 compliant DHCP client daemon
# dhcpcd -d -B eth0
dhcpcd[1865]: version 5.5.5 starting
dhcpcd[1865]: eth0: using hwaddr bc:ae:c5:75:36:8e
dhcpcd[1865]: eth0: executing `/usr/lib/dhcpcd/dhcpcd-run-hooks', reason PREINIT
dhcpcd[1865]: eth0: executing `/usr/lib/dhcpcd/dhcpcd-run-hooks', reason CARRIER
dhcpcd[1865]: eth0: sending IPv6 Router Solicitation
dhcpcd[1865]: eth0: reading lease `/var/lib/dhcpcd/dhcpcd-eth0.lease'
dhcpcd[1865]: eth0: rebinding lease of 192.168.1.100
dhcpcd[1865]: eth0: sending REQUEST (xid 0x36169f23), next in 3.93 seconds
dhcpcd[1865]: eth0: acknowledged 192.168.1.100 from 192.168.1.1
dhcpcd[1865]: eth0: checking for 192.168.1.100
dhcpcd[1865]: eth0: sending ARP probe (1 of 3), next in 2.00 seconds
dhcpcd[1865]: eth0: sending ARP probe (2 of 3), next in 1.81 seconds
dhcpcd[1865]: eth0: sending IPv6 Router Solicitation
dhcpcd[1865]: eth0: sending ARP probe (3 of 3), next in 2.00 seconds
dhcpcd[1865]: eth0: leased 192.168.1.100 for 3600 seconds
dhcpcd[1865]: eth0: adding IP address 192.168.1.100/24
dhcpcd[1865]: eth0: adding route to 192.168.1.0/24
dhcpcd[1865]: eth0: adding default route via 192.168.1.1
dhcpcd[1865]: eth0: writing lease `/var/lib/dhcpcd/dhcpcd-eth0.lease'
dhcpcd[1865]: eth0: executing `/usr/lib/dhcpcd/dhcpcd-run-hooks', reason BOUND
dhcpcd[1865]: eth0: sending ARP announce (1 of 2), next in 2.00 seconds
dhcpcd[1865]: eth0: sending IPv6 Router Solicitation
dhcpcd[1865]: eth0: sending ARP announce (2 of 2)
dhcpcd[1865]: eth0: sending IPv6 Router Solicitation
dhcpcd[1865]: eth0: no IPv6 Routers available
dhcpcd[1865]: eth0: carrier lost
dhcpcd[1865]: eth0: deleting default route via 192.168.1.1
dhcpcd[1865]: eth0: deleting route to 192.168.1.0/24
dhcpcd[1865]: eth0: deleting IP address 192.168.1.100/24
dhcpcd[1865]: eth0: executing `/usr/lib/dhcpcd/dhcpcd-run-hooks', reason NOCARRIER
dhcpcd[1865]: eth0: carrier acquired
dhcpcd[1865]: eth0: using hwaddr bc:ae:c5:75:36:8e
dhcpcd[1865]: eth0: executing `/usr/lib/dhcpcd/dhcpcd-run-hooks', reason CARRIER
*** glibc detected *** dhcpcd: double free or corruption (fasttop): 0x0000000000ac2860 ***
======= Backtrace: =========
/lib/libc.so.6(+0x78a56)[0x7f9b6a794a56]
dhcpcd[0x40cdd0]
dhcpcd[0x40e597]
dhcpcd[0x4093f0]
dhcpcd[0x411ba7]
dhcpcd[0x411563]
dhcpcd[0x40768f]
dhcpcd[0x40aa6b]
dhcpcd[0x4028a8]
/lib/libc.so.6(__libc_start_main+0xf5)[0x7f9b6a73d455]
dhcpcd[0x402d1d]
======= Memory map: ========
00400000-00419000 r-xp 00000000 fe:02 4590719 /sbin/dhcpcd
00619000-0061a000 r--p 00019000 fe:02 4590719 /sbin/dhcpcd
0061a000-0061b000 rw-p 0001a000 fe:02 4590719 /sbin/dhcpcd
0061b000-0061c000 rw-p 00000000 00:00 0
00ac1000-00ae3000 rw-p 00000000 00:00 0 [heap]
7f9b6a2eb000-7f9b6a300000 r-xp 00000000 fe:02 1063993 /usr/lib/libgcc_s.so.1
7f9b6a300000-7f9b6a4ff000 ---p 00015000 fe:02 1063993 /usr/lib/libgcc_s.so.1
7f9b6a4ff000-7f9b6a500000 rw-p 00014000 fe:02 1063993 /usr/lib/libgcc_s.so.1
7f9b6a500000-7f9b6a517000 r-xp 00000000 fe:02 3014810 /lib/libpthread-2.15.so
7f9b6a517000-7f9b6a716000 ---p 00017000 fe:02 3014810 /lib/libpthread-2.15.so
7f9b6a716000-7f9b6a717000 r--p 00016000 fe:02 3014810 /lib/libpthread-2.15.so
7f9b6a717000-7f9b6a718000 rw-p 00017000 fe:02 3014810 /lib/libpthread-2.15.so
7f9b6a718000-7f9b6a71c000 rw-p 00000000 00:00 0
7f9b6a71c000-7f9b6a8b3000 r-xp 00000000 fe:02 3018245 /lib/libc-2.15.so
7f9b6a8b3000-7f9b6aab3000 ---p 00197000 fe:02 3018245 /lib/libc-2.15.so
7f9b6aab3000-7f9b6aab7000 r--p 00197000 fe:02 3018245 /lib/libc-2.15.so
7f9b6aab7000-7f9b6aab9000 rw-p 0019b000 fe:02 3018245 /lib/libc-2.15.so
7f9b6aab9000-7f9b6aabd000 rw-p 00000000 00:00 0
7f9b6aabd000-7f9b6aac4000 r-xp 00000000 fe:02 3014856 /lib/librt-2.15.so
7f9b6aac4000-7f9b6acc3000 ---p 00007000 fe:02 3014856 /lib/librt-2.15.so
7f9b6acc3000-7f9b6acc4000 r--p 00006000 fe:02 3014856 /lib/librt-2.15.so
7f9b6acc4000-7f9b6acc5000 rw-p 00007000 fe:02 3014856 /lib/librt-2.15.so
7f9b6acc5000-7f9b6ace6000 r-xp 00000000 fe:02 3018769 /lib/ld-2.15.so
7f9b6aea5000-7f9b6aea9000 rw-p 00000000 00:00 0
7f9b6aee4000-7f9b6aee6000 rw-p 00000000 00:00 0
7f9b6aee6000-7f9b6aee7000 r--p 00021000 fe:02 3018769 /lib/ld-2.15.so
7f9b6aee7000-7f9b6aee8000 rw-p 00022000 fe:02 3018769 /lib/ld-2.15.so
7f9b6aee8000-7f9b6aee9000 rw-p 00000000 00:00 0
7ffff8b93000-7ffff8bb4000 rw-p 00000000 00:00 0 [stack]
7ffff8bc9000-7ffff8bca000 r-xp 00000000 00:00 0 [vdso]
ffffffffff600000-ffffffffff601000 r-xp 00000000 00:00 0 [vsyscall]

Juniper networks VPN: Network Connect will not install under Snow Leopard

Created different thread based on the topics from http://discussions.apple.com/thread.jspa?threadID=2130935.
With new install of Snow Leopard i get the following when trying to log into SSL VPN "Could not launch. Please restart the web browser and try again"
can not do the workarounds from the above thread since none of the directories exist. Has anyone found a fix for this?

I ran into this too (made matters worse by cleaning out the old juniper install). What I understand clearly now, which other discussions with all the happiness from people saying they fixed it seem to miss completely: Juniper only works if you installed it prior to upgrading 10.6. If you did not, you are possibly hosed.
Now, I was hosed, but I found a workaround. Find a stand-alone installer .dmg out there. As of a couple days ago it was there. I'm sure it still is. Google it. NetworkConnect.dmg.
It is version 6.0.0. It installs correctly. My company runs 6.4.0, which means the first time you open NetworkConnect after installing it prompts you to upgrade. The upgrade worked fine, so long as I was running as root.
Which brings me to my original problem which I've not seen anyone else complain about, which has me worried: after installing, NC only actually connects and functions when I run as root. I'm not talking about su - root or using sudo, I mean having to graphically switch users and log into the computer as the root user (after enabling it...using the scenableroot I think, something like that).
Has anyone else seen this behavior? I can launch Network Connect as my real user but it immediately fails with a software error. 'ncproxyd.error: Failed to gain root privileges'. Driving me batty.

Limited network connectivity after reboot

I have a Windows Server 2008 sp2, and every time it does a reboot, I lose the network connection. the system tray will either have a red x or it will say limited network connectivity. If I run a repair it says the network cable is unplugged.
The only way I have found to resolve this is is to go into manage network connections, and disable the network adapter, and then enabling the network adapter. This server worked fine for about three years, before the problem started occurring.
Any ideas would be appreciated.

I found a newer network driver, and will install probably on Monday. This is the server that runs all our backups, so I have to wait to install the driver until the next backup job finishes. The only warning I am getting is:
Broadcom NetXtreme Gigabit Ethernet #2: The network link is down. Check to make sure the network cable is properly connected.
If updating the driver does not help then it might something wrong with the NIC. You can try replacing it and see if that helps.
This posting is provided AS IS with no warranties or guarantees , and confers no rights.
Ahmed MALEK
My Website Link
My Linkedin Profile
My MVP Profile

No network connection after windows 10 install

Similar Messages

Maybe you are looking for