No network, WiFi, 3G after iOS 7.0.6 Update (iPhone 4s)

Following my update to iOS 7.0.6 which completed with no apparent problems, my phone has lost all connectivity to my network, WiFi and 3G services.
'Carrier Settings' no longer appears in my Settings menu, and in 'About' I cannot view IC, or IMEI number - they appear to have disappeared. Furthermore, Network appears as "Not available".
Instead of 'Sim Fault', 'No Sim', or carrier information in the top left of the screen I have 'Searching' instead.
I have spoken to my network provider who cannot provide me an answer, and instead have pointed me in the direction of Apple.
I have attempted the following thus far with no result:
Soft reset - same result
Recovery mode reset - same result
Reset all settings and content - Not possible as cannot verify Apple ID password with no internet connectivity
Reset carrier settings - same result
Restore iPhone via iTunes - Not possible as cannot turn off Find My iPhone, cannot verify Apple ID to turn off function without internet connectivity
Attempted different sim in same phone - no change, 'Searching' still present in top left and no WiFi / 3G
Please if anyone can offer any support in this matter I would greatly appreciate it.

I just updated from iOS 7.0.4 to 7.0.6 and now my carrier signal is UNSTABLE. It will have a complete signal with 3G, and then after a few seconds the 3G signal will be lost and then the carrier symbol will be lost, and then the signal bar will decrease from 5 bars to no signal at all and then just repeat the cycle.   I can receive messages but only when the signal is complete. I'm very frustrated coz i also use mg 3G connection as my internet through tethering but since the signal is unstable, i can't use it properly!

Similar Messages

  • Rear camera stopped working after iOS 7.1.2 update- iPhone 5

    My rear camera is not working after I did 7.1.2 software update this morning. I see a blank screen when I click the camera app.

    So my camera was fine until yesterday and pressing on the lens did not work so I went back to looking for solutions:
    http://www.cydiaios7.com/back-camera-not-working-after-ios-7-update-solution.htm l
    The article is from last year (IOS 7), but solution 1 worked for me. Here are all the solutions from the link:
    Solution 1
    Hold the Sleep button until you see the Slide to Power Off slider
    Slide it and then immediately hold down the Sleep button again until you see the Apple logo
    Solution 2
    Open your Settings app
    Tap General
    Tap Reset
    Tap Reset All Settings
    While you won’t lose any of your data you will have to re-enter all of your passwords and personal settings again
    Solution 3
    Hold the Sleep and Home button simultaneously until the Apple logo appears
    Let go of both buttons at the same time and let your iOS device boot up as normal
    Solution 4
    Try a different camera app instead of the stock one – downloadCamera Awesome, free of charge, from the App store
    Install and both cameras should work properly.

  • WiFi Problem after iOS 4.3.3 update

    Hi
    After the update to the IOS 4.3.3 all of the IPAD 2 from my company(six IPAD 2) I started to have many problems connecting to wireless network from my company.I saw that the IOS 4.3.4 the bug persists.
    I would to now if the IOS 4.3.5 fix this BUg or i have to wait until IOS 5.
    Regards
    VC
    iPad

    First, Thank you for the support that you are given me related to this situation,but you have to understand my reluctance to accept that this is not a IOS problem because all the six / seven have the same problem.
    (five minutes after)
    I tested a new connect using WEP and I coul connect with problem.When i try to use WP2-PSK, no connection.This situation in both technologies(Cisco and Alcatel)

  • Iphone 4s cannot surf at all wifi/cellular after ios 7.1.1 update

    worked yesterday on ios5.1.1, just updated ... what can be done? why this is happening? (The phone is in perfect condition, yesterday it worked properly.

    Settings > General > Reset > Reset Network Settings

  • No network LAN-connection after iOS 5.1.1update

    Today i tried to solve a big issue after updating my AppleTV's to 5.1.1 (actual version: AppleTV3,1_5.1_10A406e_Restore.ipsw). After updating my Apple TV´s, they could not connect to  the Apple activation server. No Home Sharing was adjustable and also logging in iTunesStore was not possible. The update I have done via LAN cable, and I changed  nothing in my network configuration. The network (networkadress via DHCP) is indeed set up by default in the AppleTV automatically. Nevertheless, nothing went. Then I removed the network cable and made a reset of the AppleTV and tried to connect via Wi-Fi. With Wi-Fi, he finds the activation server and everything works as it should. Home Sharing, iTunes, streaming. However, once the network cable is plugged in and the Apple TV is restarted, it is again not possible to get access the iTunesStore. Home Sharing is not possible. The networkcable are fine. Both MacBook, as well as my TVs have internet connection over the same network cable. If I unplug the network cable from the AppleTV again, anything goes. Only via WLAN, but it's just too slow to stream data from my Mac. I have this "strange behavior" on 3 AppleTV 3.Gen., which are in the apartment. The previous iOS-Version on the same network cables, worked great. Can anyone reproduce the problem? Or have I now 3 bricked devices? I tried to downgrade over itunes. But this is not possible anymore. I installed 3 times the update. But nothing goes. Please can anybody help me.

    I found another link titled "Apple TV Death after update"  and found several links that have proven to work to restore to the previous version.  Here is my post:
    "I had originally replied to a post titled "No network LAN-connection after iOS 5.1.1 update". That has been my issue after updating to 5.1. Wirless worked for me but iTunes match and Podcasts were slow to respond. I finally downgraded to the previous version (5.0.2). So far, my ATV3 has been operating exactly as it did out of the box. No more activation failed message, and all components of ATV are functioning flawlessly on my whole home LAN network.
    I also wonder what Apple was thinking for releasing this update without adaquate testing. I can forgive them for Maps, but not this. ATV has been around long enough for all of the kinks to be worked out and any updates to just plain work. I did like the new menu displays in apps and how you could rearrange the program icons on the home screen.
    Perhaps they will get it right. Some day. But until they show proof that any future updates are correct and provide detailed instructions on how to revert back to a previous version, I will be very leary of updating. Spending a week reading message boards on how to do a simple resotre is not my idea of how to spend my weekends.
    As a side note, I am a PC, so to restore from an .ispw file located on your system, you must press the Alt & Shift keys togather, then click the Restore button, and a window will pop-up so you can select the location for the restore file."
    Directions to restore:
    "Yes you can. I am a PC. Download the .ipsw file and save to your desktop. Unplug the LAN, HDMI and power cable. Connect the usb cable from your laptop to the ATV. If iTunes does not automatically launch, start it. After iTunes is running, plug in the power cable to the ATV. iTunes will recognize the ATV and will open the restore window in iTunes.
    Press the Alt and Shift keys togather, then click on the Restore button. A file window will open so you can navigate to the desktop (or where ever you saved the file). Select the AppleTV3,1_5.-.2_9B830_Restore.ipsw file. iTunes will start the restore process.
    When you see the message that it has completed the restore, unplug the usb cable and power cable. Reconnect the LAN and HDMI cable then plug in the Power cable in that sequence.
    Follow the setup procedure again and all should be as it was before."

  • IPhone 6 screen freezes and can't find wifi after iOS 8.0.2 update

    iPhone 6 screen freezes and can't find wifi after iOS 8.0.2 update. Have to do a hard reboot. I am Extremely disappointed and lost ALL trust in Apples Quality Assurance. From now on I'll wait a week before I update.

    Hey there Shortos,
    It sounds like your phone touchscreen is not consistently working for you after updating to iOS 8. I can see how that would be pretty frustrating. It sounds to me like this could be a software issue or an issue with the screen itself. I would start with the troubleshooting in the following article to help troubleshoot the screen itself:
    iPhone, iPad, iPod touch: Troubleshooting touchscreen response
    Restart your device
    Hold the On/Off button until "slide to power off" appears. Slide to power off your device. When it is off, press the On/Off button to turn it back on.
    If you can't restart your device, reset it by pressing and holding the Sleep/Wake button and the Home button at the same time for a least ten seconds, until the Apple logo appears.
    Clean the screen with a soft, slightly damp, lint-free cloth.
    Avoid using the device while wearing gloves, with wet hands, or immediately after applying hand lotion.
    If you have a protective case, or if you are using a plastic sheet or film on the display, try removing them and testing the device without it.
    If that does not resolve the issue, I would next quit all the running apps on the device:
    iOS: Force an app to close
    Double-click the Home button.
    Swipe left or right until you have located the app you wish to close.
    Swipe the app up to close it.
    When you have done that restart the device and test the issue again:
    iOS: Turning off and on (restarting) and resetting
    Thank you for using Apple Support Communities.
    All the very best,
    Sterling

  • Since upgrade to IOS 10.9 and associated iTunes 11.1.3, I can no longer WiFi sync iPad (IOS 7.0.3) nor iPhone (IOS 6.1.3).  USB connection is required.  Formerly I could sync both devices without locating them physically (not necessarily charging).

    Since upgrade to OS 10.9 and associated iTunes 11.1.3, I can no longer WiFi sync iPad (IOS 7.0.3) nor iPhone (IOS 6.1.3).  USB connection is required.  Formerly I could sync both devices without locating them physically (not necessarily charging).  I have restarted both devices, turned off and on "Sync with this iPad/iPhone over WIFI" and restarted WiFi.  WiFi is operating (iPad has no SIM).  What next?

    I'm also affected by this bug in exactly the same way as you.
    Some users have had success by closing iTunes, enetering (on OS 10.9) settings --> network --> edit locations, then create a new location with the same wifi/network settings. Then restarting iTunes.
    Others have had some success by editing settings --> iCloud --> de-selecting keychain
    neither of these fixes have worked for me.
    It appears that the iPad can "see" iTunes running on my iMac because when I open settings --> general --> 'iTunes wifi sync', "sync now" is greyed out if iTunes is not running. When iTunes is started, "sync now" is enabled but just doesn't work. Nor does the iPad appear in iTunes.

  • After ios 8 update has anyones ipad started randomly selecting everything? Even after ios 8.0.1 update it has still continued to do the same thing.

    After ios 8 update has anyones ipad started randomly selecting everything? Even after ios 8.0.1 update it has still continued to do the same thing making it immpossible to use ipad anymore. Has anyone had the same problem and/or knows how to fix this?

    Try a Reboot pess & hold power button & menu button hold both down until you see Apple Logo you will not lose any data This may help but the ipad 2 is a bit under powered for iOS 8 If you can a very good buy now is the iPad Air 32G Since they brought the new one out the price for this model Has come down by £120.00 That's the one I am using and it works great on iOS 8.1 Bsydd uk

  • Internet not connecting after ios 7.0.2 update on iphone 5

    Internet not connecting after ios 7.0.2 update on iphone 5

    Hi there PompasJr,
    I would recommend taking a look at the troubleshooting steps found in the article below.
    iPhone: Hardware troubleshooting
    http://support.apple.com/kb/TS2802
    Camera isn't functioning
    If the screen shows a closed lens or black image, force quit the Camera app.
    If you do not see the Camera app on the Home screen, try searching for it in Spotlight. If the camera does not show up in the search, check to make sure that Restrictions are not turned on by tappingSettings > General > Restrictions.
    Ensure the camera lens is clean and free from any obstructions. Use a microfiber polishing cloth to clean the lens.
    Third-party cases can interfere with the autofocus/exposure feature and the flash (iPhone 4 only); try removing the case if you have image-quality issues with photos.
    Try turning iPhone off and then back on.
    Tap to focus the camera on the subject. The image may pulse or briefly go in and out of focus as it adjusts.
    Try to remain steady while focusing:
    Still images: Remain steady while taking the picture. If you move too far in any direction, the camera automatically refocuses to the center. Note: If you take a picture with iPhone turned sideways, it is automatically saved in landscape orientation.
    Video: Adjust focus before you begin recording. After recording begins, you cannot readjust focus until you stop recording. Exiting the Camera application while recording will stop recording and will save the video to the Camera Roll. Note: Video-recording features are not available on original iPhone or iPhone 3G.
    If your iPhone has a front and rear camera, try switching between them to verify if the issue persists on both.
    -Griff W.

  • Touch ID doesn't work after ios 7.1.1 update

    Touch id doesn't work after ios 7.1.1 update..
    Why????

    After IOS update, you first have to use passcode.
    Passcode is needed when
    After restarting your iPhone 5s
    When more than 48 hours have elapsed from the last time you unlocked your iPhone 5s
    To enter the Touch ID & Passcode setting

  • Problems with sound from external speakers after iOS 5.0.1 update

    Have others experienced problems with external speakers on the Iphone 4 after iOS 5.0.1 update?  My phone no longer rings, sounds when i receive a text message, sounds alarm, etc.  Vibrate works fine and when i plug in headphones I can hear music through the headphones.  Any fixes for this?

    Hi Guys,
    I have post eariler on another forum and I have the same problem, I have tried all the things listed here and nothing was perminant in fixing this painful iphone hating problem.... and failed.  You probably have the problem when you use youtube or your music external speaker that there is no volume bar and no sound.   I have had the same problem But I need to happily say that I now have the fix!!!!  This worked for me and I fixed it by myself so you don't need to go to apple or service centre or anything.
    Ok I like so many of you here truly believed this was as IO5 issue as it only dropped the sound on the speakers once that IO5 update came along.  I tried a bunch of reset, reboots, home clicks, lock and unlocks, to fix this and all failed.  some worked for an hour but then failed.  hours of my life that I will never get back.   but since I have learnt this is not a IO5 problem but a hardware issue! ...  and in paticualar is has to do with your bottom connection.  Your phone is thinking it is docked all the time.
    To fix the no sound problem what you need is...
    1.  a torch
    2.  a tooth brush
    3.  methalated spirits
    4. a butter knife
    Step 1.
    get your torch and shine it down the bottom connection plate to see what kind of dust, sand, hair or anything you have stuck in there.   all that need to be removed!  everything!  it might look clean but still thats ok go to step 2.
    step 2.
    Turn on your music app and put the speakers on!  If your phone is like mine it should not work.  you most probably don't even have the volume display to turn it on but its ok, just do it! and it should still play with no sound.   its important you try and run the speakers as this will show you that it is a hardware problem.
    step 3.
    Dip your tooth brush into some methated sprits.   then at your sink tap the exess metho out of your brush as you just want the brushes to be slightly damp, not soaking wet and then scrub the bottom connetiors on your iphone.  work the brush back and forward in a way that scoops the dirt out of the phone, not just pushing it side to side.
    (As you bushing you should notice the volume bar come back on or off as you scub.   This happened to me and that is how I realised I was on the right track to fixing this problem as I was doing something external that was actually controling when the volume display came on or off.   but once I cleaned it this still didn't fix the problem...)
    Step 4.
    Use the back side of a butter knife (not the sharp side) to gently slide over the connectors on the iphone.  Do this gently as you are only pushing down on the tiny metal contect bars and you should notice the volume display come on again.  slide it back and forward.  Now the area of interest is about 2/3 along the connection plate to the right.   This is the area that has the infomation sent when your iphone thinks its docked.
    This has worked for me and I have not had a problem since I did this 2 weeks ago.   I have since learnt that the new IOS 5 has activated a different part of the bottom conectors.  if you have been using dodgy connectors or unapproved apple cables (as I was)  any damage or hair and dirt on the terminal this is effecting it.  Try it.   just remember if you can do something external to your phone then there lies the problem.
    Hope this works for your phone as it did for mine.
    Cheers

  • My ical won't sync with iPhone 4 after IOS 6.0.1 update

    My ical won't sync with iPhone 4 after IOS 6.0.1 update. The "sync calendars" option is no longer available after I installed this update. Any ideas???I have tried a few times to sync, and nothing has changed on my calendars. I have had so many troubles with this update. Grrr...

    I tried the same but it did not worked. But, i got a solution. I accessed gmail on my laptop. Went to gmail settings. There is a option to add a device. A iPhone was already listed. I clicked Revoke to remove it. Then i clicked add new device and gave it iPhone name and a new 16-20 character password was geenrated. I used it to configure gmail on my Iphone and it worked beautifully. So glad i have been able to fix this. That password is a one time password to authenticate that device.

  • HT201210 My iphone 4 crashed after iOS 7.1.1 update

    My iphone 4 (7.1) crashed after iOS 7.1.1 update. iTunes is unable to recover it. Has anyone encountered similar issues?

    Hello Rajesh,
    Thank you for providing the details of the issue you are experiencing with you iPhone repeatedly becoming unresponsive.
    I recommend following these steps for an issue like this (you can skip 4 because it does not relate to the issue you are experiencing):
    If a single application is not responding or stops responding when it opens, you can force it to close.
    If the device is unresponsive or if certain controls aren't working as expected, restart your device.
    If the device remains unresponsive or does not turn on (or power on),reset your device.
    If there is no video or if the screen remains black, verify that the device has enough charge to turn on:
    If you are using an iPad, ensure that it's connected to the USB Power Adapter supplied with the device.
    Let charge for at least twenty minutes, then see if it starts normally.
    If there is no image on the screen, press the Sleep/Wake button to attempt to wake the device.
    If the screen displays a red battery icon, continue charging the device until the battery is fully charged.
    If the above steps do not resolve the issue, or the if the screen remains black or shows a persistent Apple logo, try restoring with iTunes:
    Connect the device to your computer and open iTunes.
    If the device appears in iTunes, select and click Restore on the Summary pane. Learn more about restoring iOS software.
    If the device doesn't appear in iTunes, try to force the device into recovery mode, and then restore it.
    If the above steps do not resolve the issue, contact Apple.
    You can find the full article here:
    iOS: Not responding or does not turn on
    http://support.apple.com/kb/TS3281
    If you get to step 5, I recommend backing up your iPhone before performing the restore:
    iOS: Back up and restore your iOS device with iCloud or iTunes
    http://support.apple.com/kb/HT1766
    Thank you for using Apple Support Communities.
    Best,
    Sheila M.

  • HT201398 Why won't podcast app work on iPhone 5 after ios 8.1.3 update?

    Why won't podcast app work on iPhone 5 after ios 8.1.3 update?
    I've restarted the phone and itunes several times, have uninstalled and reinstalled the app on the phone and itunes separately, and it still just shows 'Installing" under the greyed out app.

    I have the same problem with an iPhone 5s. All podcast fail to work on the phone since updating to iOS 8.1.3. What is going on? Is Apple taking this problem serious?

  • After iOS 7.0.2 update: Freeze on lock screen, blackout & unresponsive for 5 min then the phone restarts itself

    Happened after iOS 7.0.2 update a few times (2x this morning): Freeze on lock screen, "blackout:" unresponsive to any buttons pressing, after 3-5 minutes the phone restarts itself and works again... (1) May I ask what can I do? I am trying to reset it and recovering the data from backup. (2) Can a virus cause this problem?

    To rule out a software issue, set it up as new device without using the latest backup.
    iOS: How to back up your data and set up your device as a new device
    If it does not charge normally after that, you'll have to get it serviced, the problem might be hardware related.
    iPhone - Contact Support - Apple Support

Maybe you are looking for

  • Script logic - how to use a selection variable within an allocation logic

    Hi, I want to implement a simple top-down distribution to distribute values from a yearly budget (Y20xx.TOTAL) to a quarter budget (Q20xx.Q1, ... Q20xx.Q4) using the actuals of the previous year as reference. If we hard code the members it works fine

  • Can you partition the Time Capsule hard drive?

    I would like to back up through AirportExtreme 2 different Macs with Time Machine but obviously I would first need to partition the Time Capsule HD ! Is it possible and how would I go about this? I can't find no infos in the manual... Thanks for your

  • Lost Playlist info

    I recently had to replace the logic board on my Powerbook G4 and have been reinstalling my iTunes library from my external harddrive. Everything has reinstalled except my Beatles music. The individual songs show up but not as separate albums. Any ide

  • Blackberry Pearl Battery Cover Clip Broken

    My pearl took a little fall and now the silver battery clip has broken (with the spring coming out and such).  Can I buy a replacement clip for the battery cover?  Where would I find this?

  • Cash Sales - Acc.Seq - Acct Key error

    Hi! I'm doing the Cash Acct Detmn, where the acc.seq. is having only to table 004 & 009. I reqd a Acctkey table in that acc.seq. So, used table 005 which has Sal Org and acct key. But when activating the fields, the Acct key is showing error as the f