No onboard sound- MSI k7n420 Pro after installing ATiI 9700 pro

I'm not sure if this has been answered previously.
I just installed an ATI 9700 pro on my MSI K7N420 Pro. Video card works great, but sound is absent after installing vid card.
In device manager shows yellow marks on nforce audio codec interface and nforce midi Uart. The former says: NtKern.vxd device loader for this device could not load the device driver. THe latter says: This device is either not present,, not working properly, or does not have all drivers installed.
I tried reinstalling the drivers using the windows files present in system, but nothing changed.
I'm not sure what to do next.
Any help would be appreciated.
System hardware:
MSI K7n420 MB with onboard sound & video, ver 1.05
ATI 9700 Pro video card
512 MB ram pc2100
40 GB western HD
win98

Hi,
Win98 - SE? Although this board (K7N420) works fine with Win 98 it can have driver issues (although, it's that long since I installed it - I can't remember what they were!). An upgrade to XP (Pro if possible) should be at the top of your Xmas list - then issues such as the one you're having should be a thing of the past
The card will work with DirectX 8 but as far as I know the 9700 is fully DirectX 9 compatible - so you should really install it as it enables more features.  
You can find your BIOS version on the initial boot screen!
Have you any IRQ conflicts? - Check device manager.
Is PNP OS enabled in your BIOS? if so disable it and see what happens. Also Enable APIC! (BIOS)
Axel  

Similar Messages

  • HT4356 Mavric doesn't support my 5 years old Big Screen Display, OR? Tried to connect my Mac Book Pro after installing Mavric, The Screen didn't work as before. I could only see the Desktop but not the movies for example. What can I do?

    Mavric doesn't support my 5 years old Big Screen Display, OR? Tried to connect my Mac Book Pro after installing Mavric, The Screen didn't work as before. I could only see the Desktop but not the movies for example.
    <E-mail Edited by Host>

    It appears what happened is the installer though it was looking at a empty drive and just went ahead and installed.
    I of course am assuming here you didn't use Disk Utility to format the drive first before installing, that would wipe out your files and programs for sure.
    So what to do, what to do.
    Well there is hope for you as long as the drive wasn't Filevaulted.
    I'll explain. When a hard drive writes data for the first time to a drive, it starts at the very top and works it's way down.
    When OS X was installed the first time, it was at the top of the drive, unless you upgraded then the upgraded OS X could have been written elsewhere.
    Now when you just reinstalled OS X, the new OS went on the top of the drive, overwriting any data that was there previously, so what was there you have lost forever which is about 8GB or so. If it was the previous OS there, then your more in luck because only the old OS X was overwritten.
    The remaining space on the drive still can have a copy of your files, provided it's not overwritten yet.
    It's because when a hard drive deletes data or reformats, it doesn't remove the data off the drive or overwrites it immediately, it's just made so it's SPACE is available for new files to be written there.
    So technically one can recover the deleted data off a non-encrypted/scrubbed hard drive with special software.
    The way it does this is it reads the 1's and 0's of the files themselves, and through a lot of figuring out, can tell what that file is and what it belongs too.
    So what you will have to do is this:
    Create a data recovery/undelete external boot drive
    or if you don't have the skills, then take it to a local PC/Mac tech and they can do a direct image of the drive and then you can run Data Rescue on it to rebuild your files.

  • Snipping Tool stopping working after installing Office 2013 Pro (32 bit) on Win 7 Pro 64bit - help?

    Have been looking at many forums to fix this:
    ran SFC - no errors
    rebooted multiple times
    all Windows Updates are current
    don't want to disable antivirus, as some have suggested
    Uploaded a registry fix, which several have suggested - no soap
    Note:
    all other features of this PC work great - zero issues.
    the issue starting right after installing Office 2013 Pro - 32bit.  It runs fine.
    "Paint" runs fine.  "Print Screen" works fine - image goes to clipboard, and I can paste anywhere.
    get the standard message everyone posts in forums: 
    "The Snipping Tool is not working on your computer right now. Restart your computer, and then try again. If the problem persists, contact your system administrator."
    Have tried other free third-party tools, and they are cumbersome, and I love the MS Snipping Tool.
    Advice?  Tips?
    Thanks,  
    Dave
    DavidLum

    Hi,
    Import this key back into the registry, log off and back on to check if it works.
    Windows Registry Editor Version 5.00
    [HKEY_CLASSES_ROOT\AppID\{7F429620-16D1-471E-A81A-114992148034}]
    @="wisptis"
    "RunAs"="Interactive User"
    "LaunchPermission"=hex:01,00,14,80,64,00,00,00,74,00,00,00,14,00,00,00,30,00,\
      00,00,02,00,1c,00,01,00,00,00,11,00,14,00,04,00,00,00,01,01,00,00,00,00,00,\
      10,00,10,00,00,02,00,34,00,02,00,00,00,00,00,18,00,1f,00,00,00,01,02,00,00,\
      00,00,00,05,20,00,00,00,20,02,00,00,00,00,14,00,0b,00,00,00,01,01,00,00,00,\
      00,00,01,00,00,00,00,01,02,00,00,00,00,00,05,20,00,00,00,20,02,00,00,01,02,\
      00,00,00,00,00,05,20,00,00,00,20,02,00,00
    If problem persists, please refer to another thread discussion with this problem.
    http://social.technet.microsoft.com/Forums/windows/en-US/610ecb85-9aea-472c-8590-b835a0982f68/snipping-tool-fails?forum=itprovistaapps
    Roger Lu
    TechNet Community Support

  • No audio Mac Pro after installing OS 10.7.5 Update 1163

    No audio on Mac Pro after installing OS 10.7.5 Update 11G63. Tried uninstalling iTunes Dock Notifications but it wasn't installed in the first place. No Audio on iTunes, youTube, Chrome, etc.

    Hello Howard,
    Thank you for using Apple Support Communities. 
    You can use the following article to sort your your audio issues on your MacPro:
    Troubleshooting issues with no audio from built-in speakers on Macs
    Regards,
    Jeff D. 

  • After installing Adobe Premiere Pro product CS6 in the program is not active PlayBack

    After installing Adobe Premiere Pro product CS6 in the program is not active
    PlayBack button setting when creating sequence.
    Windows 7 64-bit. Intel Xeon 2, RAM 12 MB. Mxo2

    Hi,
    Thanks for posting that screenshot. It appears that you have opened your Sequence Settings for a DV-NTSC sequence and have made a circle around the "Edit Settings" button.
    Since you chose to create a DV sequence, you cannot change those settings.
    Do you have DV NTSC clips? If so, these are the correct settings.
    If you do not have DV NTSC clips, do not be concerned. Just create the sequence.
    Once you drag a non-DV clip into the DV sequence, it's OK.
    You have the option of changing the Sequence Settings to match those of your clip in a new dialog box.
    Click "Change Sequence Settings" in the dialog box.
    I hope that helps.
    Thanks,
    Kevin

  • Are there Game Apps for MacBook Pro after installing Maverick

    Are there any Game Apps for MacBook Pro after installing Maverick IOS?  Any suggestions?  Thank you.

    The Game Center:  http://support.apple.com/kb/HT4314 

  • I have a very slow startup for a macbook pro after installing Maverick

    I have a very slow startup for a macbook pro after installing Maverick

    Try SMC and NVRAM resets:
    http://support.apple.com/en-us/HT201295
    http://support.apple.com/en-us/HT204063
    Then try a safe boot again:
    http://support.apple.com/en-us/HT201262
    Ciao.

  • Wifi keeps dropping out on MacBook Pro after installing Yosemite

    Wifi keeps dropping out on MacBook Pro after installing Yosemite. This is not good.  Apparently, a lot of people are having this issue with Yosemite.  Any suggestions for my MacBook Pro?  It's bad enough that Yosemite looks so boring, but to have a major issue like constantly disconnecting from wifi is deplorable.
    I plan to keep Mavericks on my iMac until this issue is resolved.

    Wi-Fi: How to troubleshoot Wi-Fi connectivity
    Wi-Fi Problems in OS X Yosemite
    Wireless Diagnostics
    Also try turning off Bluetooth.

  • After installing Acrobat X pro as a trial, I cannot use the software and Im required to enter the serial number to continue

    After installing Acrobat X pro as a trial, I cannot use the software and Im required to enter the serial number to continue
    Under Continue to use as a trial it shows 0 days remaining.

    Trial mode expires prematurely
    http://helpx.adobe.com/x-productkb/global/trial-software-expired-early.html

  • HT201974 I just installed a wireless cable modem for a desktop PC and my MacBook Pro;  After installing, I changed the password on the wireless connection at the PC but it is not being recognized by Airport as the new password.

    I just installed a wireless cable modem for a desktop PC and my MacBook Pro;  After installing, I changed the password on the wireless connection at the PC but it is not being recognized by Airport as the new password. Can anyone help?

    Hi twinkytomes,
    Welcome to the Support Communities!
    The article below may be able to help you with this.
    AirPort Utility 6.x: Password-protect your wireless network
    http://support.apple.com/kb/PH5119
    Cheers,
    - Judy

  • Moving Creative Suite 4 to new laptop. New download has 9 Pro, old install had 9 Pro "EXTENDED"

    Moving Creative Suite 4 to new laptop. New download has 9 Pro, old install had 9 Pro "EXTENDED". Don't remember if my boss bought the "extended" as an exrta. BUT, when I go to Adobe and downlaod the "Extended" version, it says I have a better program already installed. IF this program is 9 Pro, then It is missing the 3D capture feature I was using to create 3D User Interactive PDFs of AutoCAD 3D models off the Model tab.   Any clue what I need to do?  Thanks,  Cliff
    [email address removed by host]

    The version of Acrobat bundled with CS4 was Acrobat 9 Pro. Acrobat 9 Pro Extended was sold as a standalone product.
    If you already have Acrobat 9 Pro Extended, then untick the option to install Acrobat when installing CS4, and you can carry on using the standalone copy. Acrobat and CS4 don't actually talk to each other, so installing CS4 won't affect your install of Acrobat unless you force the CS4 install program to replace it.

  • No sound after installing windows 8 pro 64bit (macbook pro 2011)

    I installed windows 8 pro edition (64bit) on my mackbook pro and after installtion i run bootcamp 5.0.5.33 everything working find but only sound card not installing i have a red cross sign on my speaker in taskbar.
    after trying alot of things like reinstalling windows, audio drivers etc. but no success.
    then once again i downloaded boot camp 5 with bottcamp assistant from my mac but still not working.
    any idea?
    i am totaly dead ......:(

    people repport the drivers that bootcamp tool on osx creates include newer drivers then the 5.0.5.33 zip file from their web site

  • I am unable to open Photo on my MacBook Pro after installing ilife 11 from a disc.  The message I get says "you can't open the application iPhoto because it may be damaged or incomplete.  What can I do?!

    I am unable to open iPhoto on my Macbook Pro (OSX 10.9.3)  after installing ilife 11 from a disc.  The message I get is "you can't open the application iPhoto because it may be damaged or incomplete.  What can I do?!  Any help will be greatly appreciated.

    Reinstall it.This time delete the receipts first.
    To re-install iPhoto
    1. Put the iPhoto.app in the trash (Drag it from your Applications Folder to the trash)
    2. Download it from the App Store to reinstall It's on your Purchases List* there.
    For older versions that have been installed from Disk you'll need these additional steps:
    2a: On 10.5:  Go to HD/Library/Receipts and remove any pkg file there with iPhoto in the name.
    2b: On 10.6: Those receipts may be found as follows:  In the Finder use the Go menu and select Go To Folder. In the resulting window type
    /var/db/receipts/
    2c: on 10.7 or later they're at
    /private/var/db/receipts
    A Finder Window will open at that location and you can remove the iPhoto pkg files.
    3. Re-install.
    If you purchased an iLife Disk, then iPhoto is on it.
    If iPhoto was installed on your Mac when you go it then it’s on the System Restore disks that came with your Mac. Insert the first one and opt to ‘Install Bundled Applications Only.
    *Sometimes iPhoto is not visible on the Purchases List. it may be hidden. See this article for details on how to unhide it.
    http://support.apple.com/kb/HT4928
    One question often asked: Will I lose my Photos if I reinstall?
    iPhoto the application and the iPhoto Library are two different parts of the iPhoto programme. So, reinstalling the app should not affect the Library. BUT you should always have a back up before doing this kind of work. Always.
    Important:
    As you're on 10.9.3 you'll need to update iPhoto to v9.5 before opening it. Use Software update.

  • Trouble after installing Acrobat X Pro in Windows 7

    I just downloaded Acrobat X pro (upgrade) and installed on Windows 7 dell laptop. I had to uninstall ACROBAT 7.1 STD to do a clean install. After installing the product I was receiving low memory messages (4GB is installed) I also received a couple of blue screen followed by auto reboot. Dell claim that there is no hardware issues (brand new laptop). Are there any known issues with ACROBAT X Pro and Windows 7 pro (32bit) service pack 1  

    Hi LosBashBrothers,
    To investigate about this issue, installation logs help in a great way. Can you please share the installation log for this session ?
    To create installation logs, enable Windows Installer logging yourself. Open the registry with Regedit.exe and create the following path and keys:
    HKEY_LOCAL_MACHINE\Software\Policies\Microsoft\Windows\Installer
    Reg_SZ: Logging
    Value: voicewarmupx
    More Information : http://support.microsoft.com/kb/223300
    Thanks.

  • Default printer resets at each reboot after installing Acrobat X Pro

    I installed Acrobat X Pro yesterday, and updated it after the install to version 10.1.4.  Since that time my default printer has been reset after each computer reboot to the first physical printer on my printers list - an HP 5900 series.  I want my default printer to be my HP 6940, which is local, connected by USB, and have gone into Start/Printers and Faxes on my Windows XP Professional machine to do this.  But each time I reboot, the default is switched back to the HP 5900.  The printers have been installed on my machine for years with no issues, and I had Acrobat 9 Professional on my machine until yesterday - with no issues.  I tried live chat for help, but the representative told my it was a physical printer issue and I needed to contact HP.  Can you help me stop my computer from resetting the default printer each time it is shut down?
    The order of printers listed on my machine:
    Adobe PDF
    HP 5900 Series
    HP 6940
    (several network printers listed below here)
    Thanks!
    Bryan

    Hi William ,
    Please perform the following steps .
    > Enable the hidden Admin Account on Windows 7 ( Ref :  http://www.howtogeek.com/howto/windows-vista/enable-the-hidden-administrator-account-on-wi ndows-vista/ )
    > Disable all Non-Microsoft Startup Services. (Ref : http://helpx.adobe.com/x-productkb/global/disable-startup-items-services-windows.html )
    > Disable all the Antivirus softwares like CA, Norton,Mc Afee etc. temporarily from the computer.
    Reboot and try installing in the new enabled Admin user account and check
    Regards
    Sukrit Dhingra

Maybe you are looking for