"No password set" on c3745

Hi,
My c3745 printed "No password set" when I tried to get to the enable mode. So, I tried to do password-recovery, but it is always in the user-mode mode despite the attempts to type "Cntrl-Break", "Alt-b", "Cntrl-C" during the initial reload.
It failed to go into the Rommon mode, is it has to do with "no service password-recovery ..." being set? What else can I do to solve the problem?
Thanks in advance....
PL

you have forgot enable password and want to do password recovery with "no service password-recovery" command set. this command will enable ROMMON security which disable access to ROMMON due to which you are unable to go into the ROMMON mode.
There are only a few methods mentioned in the below URL which you can use to recover from a lost password, but all of them destroy the start-up configuration.
http://www.cisco.com/en/US/products/hw/routers/ps274/products_configuration_example09186a00801d8113.shtml
hope to help ... rate if it does ....

Similar Messages

Every time I try to download a game on my iPad it says please verify your account and follow the intrustion now I have a email n password set up and every time I click send it to my email there is nothing how do I acces this pla

Every time I try to download a game on my iPad it says please verify your account and follow the instructions now I have a email n password set up and every time I click send it to my email there is nothing how do I acces this please

Hi Mark ohara,
Welcome to the Support Communities!
The following articles will help you with your Apple ID verification:
Frequently asked questions about Apple ID
http://support.apple.com/kb/HT5622
Click on My Apple ID to access and edit your account. You will be prompted to verify your email address.
Apple ID: Associating and verifying email addresses with your Apple ID
http://support.apple.com/kb/he68
I hope this information helps ....
Have a great day!
- Judy

MY 2YR OLD LOCKED AN IPHONE 3GS THAT HAS NO SIMS CARD I TRIED ALL KIND OF PASSWORDS IT LOKED ME OUT FOR 15 MINS IS THE PASSWORD THE LAST PASSWORD SET ON THE PHONE

MY 2YR OLD LOCKED AN IPHONE 3GS THAT HAS NO SIMS CARD I TRIED ALL KIND OF PASSWORDS IT LOKED ME OUT FOR 15 MINS IS THE PASSWORD THE LAST PASSWORD SET ON THE PHONE

Please turn off your cpas lock.
All caps indicates shouting, is considered rude, and is difficult to read ( especially when you use no punctuation or sentence structure at all). Many will not read such posts.
Do as the manual says to do and restore the iphone.

Plugged in new Iphone 5 to computer and it says can't access due to password, but don't have a password set yet

I just got my new Iphone 5s activated at verizon. I came home to plug into my computer to get all my apps, etc that I had backed up from old phone. Computer keeps saying it can't access the new phone due to a password and that I need to enter password and try again. However, I don't have a password set on the new phone. Any help would be appreicated....I don't want to loose all my back up.

What is the EXACT message you're getting?

Impossible to boot MacBook Pro Retina ! impossible to start in single user mode, Openfirmware password set, but safari works!

I have got a Macbook pro retina.
I have done 2 partitions on the SSD drive. 1 for the OS and 1 for the user (with a kind of ln -s /Home/myself /Volume/Part2/myself
I was watching a movie (with VLC) in full screen for a while and I wanted to escape. Impossible, and impossible to reboot.
When I start, I have a directory with a question mark.
I have a Open firmware passwords set (that I remember).
I cannot reset PRAM. (I can not change the RAM amount inside the commuter as this is a retina model)
I cannot start in verbose mode.
I can choose a disk to boot. I see only the OS drive and not the user partition, and no 'recovery partition'. It seems that i need to do a fsck -yff on the user partition but how ?
I can start the OS partition, and i can choose 'guess' or 'myself'. If i choose myself, I have an error message :'there is a error, the session can not start'. If I start with the guess account, I restart, and then I can browse the internet with safari (this is how I am writing this text!)
=> How can i repair the partition ? (open a terminal, boot in single user mode ...?)
best regards.

Actually, the recovery partition was there, but was not shown as my user partition. I have seen that reseting the PRAM and changing the ram could remove the open firemware password. So i have turn the computer on until the battery was empty. Then I boot about 20 times, and unplug the power supply after few seconds at different step of the booting pricess. At last, the screen default resolution when booting changed, I undertood that i succeeded, and I was able to enter.
Then I boot in single user mode, removed the open firmware password, activated the root user, and everything was fine now !

Can't remember my answers for changing password setting

Can't remember my answers for changing password setting?

Apple ID Security -
Telephone Apple Care for your country and ask for the Account Security Team, then request help resetting the questions.

I have a desktop osx 10.8.2 and I want to have a password set before i log on how do i set it and still see my iphoto pictures still flash when it is in sleep mode

I have a desktop osx 10.8.2 and I want to have a password set before i log on how do i set it and still see my iphoto pictures still flash when it is in sleep mode

Open the Users & Groups pane of System Preferences and disable automatic login, and then go into the Security & Privacy pane and set the computer not to log out after a period of inactivity.
(77781)

Password entry box when no password set

Hi,
I have problem logging out when i turn the guest account off.
At the minute i have 1 use account (admin) and no guest account. The user account has no password set. When i log out the user account is automatically selected as there only is one and it shows the password entry box. But as there is no password set you have to press back and then click on the username which logs straight in.
Any fix for this? It should be that it logs out...shows the username only...and then when clicked logs straight in.
All input appreciated!

If your presented with a password screen just hit enter. This will occur with System updates as well.
Regars

Normal behaviour for "inactive passwords" setting?

If I have the OD policy for passwords set to "disable after inactive for xx days" - does this take effect if a user is not an interactive logon? ie, I have a user account setup that is used solely for connecting to a share on the server. It never "logs in" like a human would sitting at a mac. A process would connect to a share on the server using this user each day.
Related: Is there any way to setup "do not expire" for users?

Hi Jeffery
As a new user to SAP b1 I have no answer to your question but an observation. I have placed several questions on this forum about Dates because I am convinced that in B1 2007, SAP programmers made a mess in naming Date Field names in such a confusing way that they cannot tell which Date is what. For example in OINV table DocDate field is named Posting Date and in the same table the TaxDate field is named Document Date.
So this is only a guess but perhaps the Date Ranges you are referring to are pointing to the wrong DATE field so it would not work.
Good luck
Robert

I have a macbook pro (13inch). I had a firmware password set on it and updated the firmware when apple update told me to. I cannot change the firmware password or remove it now.

Hello,
I have a macbook pro which had a firmware password set on it (security-mode = command).
Update asked me to install updates and one of them was an EFI update. I proceeded and the macintosh booted just fine.
I've tried changing the firmware password, and removing the password without success so far. It's almost like the nvram terminal command does nothing as far as security is concerned.
Help would be appreciated!
J

Apparently the newer macbooks use a different utility than the older macbooks.
setregproptool will ask for the current password, and nvram is not used for these anymore.
J

"Expire Password" setting

If you check the "Expire Password" setting under a user's "Account Control", Save and then open up the user info page again, this setting becomes unchecked. So simply opening up the page again causes the user not to be prompted for a new password, whereas that is what you expect to happen. Why does that option become unchecked automatically?

Spadafo:
No. I don't want the change to be optional, nor do I want to ask the administrator to do anything; I want to do it myself.
And I found the solution: Simply do it in 2 steps:
Change the password – “Apply Changes”, then go back into the user’s page - click "Expire Password" - “Apply Changes”
That way, the "Expire Password" will apply to the new password, not the old one, and thus the user WILL be prompted to change it.
I have to consider this a fault in APEX. If you've already entered a new password, then "Expire Password" SHOULD MEAN expire the new password. It doesn't make sense for it to mean expire the old password if you've just entered a new one.
After all, it is a pretty common scenario for the end user to forget the password, in which case you want a fast method of changing it and requiring it to be immediately changed from what you set it to. So you should be able to do this by entering the User's page only once.
Edited by: Prohan on Sep 30, 2009 7:14 AM

Does supervisor password sets master hard drive password?

On lost or forgotten password - ThinkPad General we read "setting a supervisor password automatically sets the master hard drive password". This one is a powerful feature that allows administrators recovering disks whose user password has been set to an unknown string.
Does this feature applies to old systems too, let us say T40 and X40-series ThinkPads, or only to new ones?
If this feature does not apply to old systems is there a way to set a master password (only a master password, not a user one) on the drives of these old ThinkPads? Up to my knowledge the only choices are user password or master + user password. My goal is providing a mean to recover control on a drive whose user password has been set without requiring users provide a password each time the computer is booted.
Thanks!
Edit: found a reference to supervisor password setting a master hard drive password automatically from march 2008, however I am interested in computers from 2004 up to 2006.
Solved!
Go to Solution.

is1981 wrote:
Does this feature applies to old systems too, let us say T40 and X40-series ThinkPads, or only to new ones?
If this feature does not apply to old systems is there a way to set a master password (only a master password, not a user one) on the drives of these old ThinkPads? Up to my knowledge the only choices are user password or master + user password. My goal is providing a mean to recover control on a drive whose user password has been set without requiring users provide a password each time the computer is booted.
Thanks!
AFAIK, on the old systems such as T4x/X4x one must set both the user and the master password.
Cheers,
George
In daily use: R60F, R500F, T61, T410
Collecting dust: T60
Enjoying retirement: A31p, T42p,
Non-ThinkPads: Panasonic CF-31 & CF-52, HP 8760W
Starting Thursday, 08/14/2014 I'll be away from the forums until further notice. Please do NOT send private messages since I won't be able to read them. Thank you.

HT1766 My daughter locked herself out of her phone cannot remember the advanced password setting, we share an Itunes account and both recently joined the cloud, if she resets her phone all her information will be gone, will it affect the data on my phone

My daughter locked herself out of her phone cannot remember the advanced password setting, we share an Itunes account and both recently joined the cloud, if she resets her phone all her information will be gone, will it affect the data on my phone as well

No, when resetting an iPhone it resets the actual data contained within the phone, nothing on your iCloud will be affected. It is a good idea to use seperate iClouda and iTunes accounts then you can each create your own backups regularly without your daughters backup overwriting yours or vice versa.

There is an administrator already set on m y Macbook. word. Do I delete him and set myself as admin or set myself as a user. There is no password set now.

There is an administrator already on my Macbook with no password set. Do I delete him or create myself as a user?

Who is the administrator?
If it is root or wheel DO NOT TOUCH, as that is your system.
Or did you buy this computer 2nd hand?

Require Password Setting problem

Why does my require password setting always revert back to 5 seconds?
System Preferences>Security & Privacy

Hi,
I tested on my computer that is running Windows 8, but I havenot encountered the same issue. Could you please test the following thing.
1. Disable Require Password after wake up in Power Options.
2. Manually make the computer into Sleep Mode by the Power options in Charm bar rahter than close the lid.
3. Wake up the computer and check whether the issue persists.
Juke Chou
TechNet Community Support

"No password set" on c3745

Similar Messages

Maybe you are looking for