No phone service after FIOS installation

Can someone please help me.  We have had no phone service since a crew installed FIOS on part of our street Sept. 20th.  Went through troubleshooting online and final step is to call for help...hard to do since the phone has no dial tone.  

Your issue has been escalated to a Verizon agent. Please go to your profile page for the forum, and look in the middle, right at the top where you will find an area titled "My Support Cases".  You can reach your profile page by clicking on your name beside your post, or at the top left of this page underneath the title of the board.
Under “My Support Cases” you will find a link to the private board where you and the agent may exchange information.  This should be checked on a frequent basis  as the agent may be waiting for information from you before they can proceed with any actions. Please keep all correspondence regarding your issue in the private support portal.
If a forum member gives an answer you like, give them the Kudos they deserve. If a member gives you the answer to your question, mark the answer that solved your issue as the accepted solution.

Similar Messages

  • Nightmare Customer Service Verizon - DAD cannot connect phone line after fiber installation

    Similar to other complaints I have seen online yet Verizon customer service reps deny they have ever heard of the problem.  After FIOS installation my ADT system stopped communicating.
    We had Verizon FIOS triple play installed last August (2012) after a summer long marketing campaign by Verizon.  Several trips to get it.   A dropped phone number transfer order and Verizon tried to issue me a new phone number ... that took several attempts to fix. 
    Sept 2012 Our ADT service calls us to inform us our monitored alarm system stopped communicating  since Aug ... I call ADT  -they say it was Verizons fault, but could come out and fix it for a fee.  It took months to getr back to Verizon
    I first spent almost an hour online last night with a Verizon rep who claimed it was not Verizon's fault - Claiming that all the tech had to do was deliver a phone signal to one jack.  I called Verizon customer service and wasted time with that rep also.  I asked hat a supervisor call and the rep could not confirm that a supervisor would even get back to me. 
    TERRIBLE CUSTOMER SERVICE - Time to cancel Verizon

    Your issue has been escalated to a Verizon agent. Please go to your profile page for the forum, and look in the middle, right at the top where you will find an area titled "My Support Cases".
    There you will find a link to the private board where you and the agent may exchange information. This should be checked on a frequent basis as the agent may be waiting for information from you before they can proceed with any actions.

  • Home network stopped functioning after FIOS installation

    I have 2 desktops running XP and a wireless laptop running Vista.  With my old router, I was able to transfer files and print. 
    After the FIOS installation, the three computers don't "see" each other.  All 3 have internet connectivity and no problems with
    email.  The 2 destops are cabled to the router (MI424WI) and the laptop uses wireless.  My printers are cabled to one of the
    desktops.  It is most inconvenient only have 1 PC that can print.  I've tried the "Set up a network" wizard on the XP machines
    but it doesn't change anything. 
    Any ideas would be appreciated.
    Solved!
    Go to Solution.

    The firewall hint did the trick.  I tweaked Norton 360 on the desktops and I can now print and file share.  Thanks much, Justin!
    Jack

  • ADT cannot seize phone line after fiber installation

    I had my phone line switched over to fiber today and now my ADT system cannot "seize" the phone line.  It will call out properly but if you are in the middle a call and the alarm is activated it will not disconnect the current call in order to make it's own call out to the monitoring center.  Of couse this was working before.
    I talked to the tech that installed the fiber and he said his only responsibilty to me was to provide me with a dial tone, period.  I also called Verizon tech support and talked to three different people who all told me it was ADT's problem.  So now I have to call ADT and incur a fee to have them come out and fix it.  So much for Verizon's promise to me that an upgrade to fiber would not cost anything.  
    Is there anyone is this forum that may have experienced a similar problem?  Any help greately appreciated.
    Solved!
    Go to Solution.

    armond_in_nj wrote:... Verizon Digital Voice (if that's what you have and it seems likely that's the case) is capable of using typical alarm system components to transmit alarm system data.  Usually the data is transmitted using what's called "Contact ID" data, and usually the connection between the alarm system and the telco lines is handled by a simple device called an RJ31X connector.  I suspect that's the case for ADT, but you must check that with your monitoring company ...
    Some further thoughts on the issue.  Here's a link to demonstrate what's involved in the RJJ31x wiring scheme:
    http://wiki.hometech.com/tiki-index.php?page=How+to+Wire+an+RJ31X+Jack
    As you can see it appears little "hairy" and in fact there's really only one way to do it correctly.  Of course that's what alarm technicians are for, and there's no need for the average user to get into the details.
    After thinking about this a while, it occurred to me that what has probably happened in your case is that the VZ install tech never went near your RJ31x connection.  He (or she) just did what a normal install requires and got things working.  However there are certain requirements for the alarm setup to operate correctly.
    The RJ31x mustt be the first device in line after the phone line comes into the building.  In old terminology this means that it must be wired in directly after the NID (network interface device) where the phone company hooks up to your house.  In this way the alarm can take over the line for all phones downstream.
    However with FiOS Digital Voice, this is probably not how your house was connected.  I.e., the install tech can connect to your interior phone wiring network at any point and still get all the phones to operate correctly.  What doesn't happen in such a case is the alarm is not able to control all the phones downstream, because some of the phones aren't really "downstream."
    As convoluted as this seems, the way out is simple:  the alarm company must pay a visit and make sure that all your phones are connected (from the VZ ONT) after the RJ31x.  This should be pretty easy, and it's really on the alarm company to make it work.
    Let us know what you decide and what happens (using your personal service ticket mentioned by Lawrence).  Once again, good luck.

  • No phone service after a new iTunes version is issued

    I tried to use my phone yesterday and the call didn't go through. When I connected to my computer I saw that a new iTunes version (9.0.2.25) had been issued, and when I synched with iTunes it restored my connectivity. The same thing happened the previous time a new version was issued. There was no message on the phone saying it needed to connect to iTunes. I rely on the phone for continuous service in case of emergency, and don't sync it every day. If I were out of town I would be out of luck. Does Apple (or AT&T) de-activate the service each time a new version is issued, and rely on customers to re-sync when their phone goes dead?

    I have not experienced the same - not with any iTunes update when released.

  • Unable to start ./adopmnctl.sh services after fresh installation of 12.2 on linux 6.3

    Hi ,
    Installed E-business suite 12.2 on OEL 6.3 64bit.
    buildStage.sh script successfully  verified all media and executed rapidwiz script.
    Trying to start all services using adstrtal.sh but facing issue while starting adopmnctl.sh.
    Error showing:
    Starting Oracle Process Manager (OPMN) ...
    /usr/bin/linux32: /u01/oracle/prod/fs1/FMW_Home/webtier/instances/EBS_web_PROD_OHS1/bin/opmnctl: No such file or directory
    while installing "instances" directory is missing...
    Can you help to resolve issue?

    Hi,
    I logged an SR and there is a Bug logged for this for redhat and OEL 6
    The sugguested the following....
    Please try the following:
    1. Rename /etc/profile.d/modules.sh.
    2. Retry.
    This resolved one of the issues but FMW config still fails for Vision install on OEL 6 - 64 bit......
    Sr is still open and I will update if this is rescolved

  • Wireless connectivity no longer available after TWC adds digital phone service

    Hi All,
    My problem is that my wireless Internet connectivity is no longer available after Time Warner Cable added digital phone service to my existing TV and broadband Internet service.
    Prior to having the digital phone service added, my set up was a Motorola Surfboard cable modem connected to my Linksys WRT54G wireless router, with three computers (two Win XP desktops and one Win 7 laptop) wired to the Linksys router. I had wired Internet connectivity on all three computers. Importantly, I could also access the Internet wirelessly from the laptop instead of using a wire.
    AFTER having the digital phone service added, my set up is the same except that now an Arris Touchstone Telephony Gateway (TG862G) has replaced the Motorola Surfboard cable modem. I still have wired Internet connectivity on all three computers. However, now I cannot access the Internet wirelessly from the laptop. This is a real problem in that often others in the house need access to the wireless network as well.
    I should also mention that (from a wired connection) I cannot access the Linksys router any longer via 192.168.1.1. Now, the Linksys router seems to be "invisible," almost as though it were a pass-through device. I can access the Arris gateway at 192.168.0.1 (for what it's worth), but not the Linksys router.
    Also, not sure this is important, but some time ago (when my wireless was working) I had configured the Linksys router so that it wouldn't broadcast the SSID. Through the Win 7 "Network and Sharing Center" I have tried to "manually connect" to my (hidden) wireless network. The message indicates that my hidden network already exists, but I still can't connect to it.
    I've seen a few potential remedies involving power cycling the gateway and modem in certain sequences, setting the gateway's NAT mode to Bridged, etc., but nothing has worked so far. Time Warner Cable's only advice is for me to purchase (yet) another service so that the gateway can provide the wireless access, but I since my Linksys router worked before I'd rather stick with that method (and avoid yet another charge).
    I would be very grateful for any help you could provide for this problem.
    Thanks in advance.

    1. Don't hide your SSIDs
    http://www.howtogeek.com/howto/28653/debunking-myths-is-hiding-your-wireless-ssid-really-more-secure...
    2. I assume the Arris is also a wireless router. Use inSSIDer to find the best non-overlapping, non-interfering wireless channels. Change the wireless channels on both the WRT54G and Arris if necessary.
    http://www.metageek.net/products/inssider/

  • I am unable to see following SQL Server Analysis Services in central admin services after the SQL 2014 power pivot installations

    I am unable to see following SQL Server Analysis Services  in central admin services after the SQL 2014 power pivot installations
    Ravi

    Hi Ravi,
    Per my knowledge, there is no Analysis Service in SharePoint.
    After running the SQL 2014 setup to install PowerPivot for SharePoint, you need to open the PowerPivot for SharePoint 2013 Configuration tool in Central Admin Server and configure PowerPivot for SharePoint.
    After that, you will see new Service Application called "Default PowerPivot Service Application" in Central Administration.
    If you have other WFE servers, then you need to install the PowerPivot Add-In on all the other servers in the SharePoint farm.
    More references:
    http://sridharbabuk.blogspot.jp/2013/02/installing-configuring-analysis-service.html
    http://msdn.microsoft.com/en-us/library/jj219067.aspx
    Best regards.
    Thanks
    Victoria Xia
    TechNet Community Support

  • What can I do to recover data from my iPhone 4s? The phone fail to come on again after the installation of the new iOS8. The phone is locked and I didn't make any backup before the updating installation. Inside I have very important info.

    I Have problems with my iPhone 4s after the installation of the new iOS8, the phone doesn't want to switch on again. I need to recover some important data that I have inside the phone.

    Ralph Landry1 wrote:
    There isn't anything you can do to recover contents from iPhone 4s if you cannot get the iPhone to startup.  Connect it to a wall outlet so you have a solid power source, then do a reboot by holding both the power and home buttons until the apple logo appears, ignoring the red slider if that appears.  If the iPhone still will not startup, the next options to try will automatically erase your iPhone all of its contents.
    The next step is to do a restore via the recovery mode as described in http://support.apple.com/kb/HT1808 but again note that this erases the iPhone.
    Thank you Landry, it is really a good experience to solve problem of iPhone Data Recovery!

  • Plz Help, i downloaded ios8 on my 5s and it went to recovery mode after clicking installation.then downloaded by itunes and loaded but cant find my apple ID as i forgot everything. the phone is useless and cant be activated. wot can i do????plz help

    Plz Help,
    the last night  i downloaded ios8 on my 5s and it went to recovery mode after clicking installation.
    then downloaded the ios8 using itunes and loaded but cant find my apple ID as i forgot everything.
    the phone is useless and cant be activated. wot can i do????plz help

    Apple has a number of ways to help you find your Apple ID and password:
    https://iforgot.apple.com/appleid
    If you forgot your Apple ID password
    Apple ID: Contacting Apple for help with Apple ID account security

  • After 4 days OK service, now I get NO SIM card installed message and no phone service!?

    after 4 days OK service, now I get NO SIM card installed message and no phone service!?

    Try removing your sim card, then reseating it:

  • HT201270 Hi! Does anyone's phone constantly become "No Service" after install iOS5.1?

    After installing iOS 5.1.1, my phone become "No Service" after using for few hous. What should I do to stay with the carrier, so I can make and receive calls and messages?

    Restore it back to factory settings
    http://support.apple.com/kb/HT4137
    See if that helps..

  • How to update my new phone number after my U-verse phone service is disconnected?

    How to update my new phone number for forwarding  after my U-verse phone service is cancelled/ disconnected?

    I did call them. They said once the phone service is disconnected, there's nothing they can do about it. The thing is that when I called them to cancel the U-verse service yesterday, they did not offer me the opportunity to update the new phone #. This is so frustrating!

  • Iphone 4 has no service after replacing screen and updating, phone company says sim is fine. any ideas? thanks

    iphone 4 has no service after replacing screen and updating, phone company says sim is fine. any ideas? thanks

    We had this happen with a ipad mini, took it back to person who worked on it, after a week with trying to get it working again, he replaced it. I will agree with the other replies take it back to repair place there must be something inside the phone that if you don't do repair excalty right it messes up all phone functions. Also I would give the repair person a time frame to either get it working or replace it.

  • 3gs no service after updating to ios 5 tried network reset, reset all settings and even restoring from back been with out phone for 3 weeks now need help telus cant find network problem and apple has bad customer support please help!!!

    my 3gs has no service after updating from ios 5 tried resetting network settings, resetting all settings and restoring from back up on itunes.
    telus cant find any network problems and apple is difficult to deal with.please help 3 weeks with no phone and $70 a month not happy.

    I have been having a similar problem for the last few days.Without warning the signal will just completely duck out leaving the device searching for several minutes before settling on a no signal message.
    Sometimes restarting the device, toggling data and 3g settings or toggling Airplane Mode will set things right. However, a lot of the time I've been left without a working phone.
    I don't believe this is a SIM issue, as I had to change my SIM only one month ago for another signal related problem. Again any help would be appreciated here as well.

Maybe you are looking for