NO POST - Need Help

I recently purchased SiS661FM motherboard. I already own Intel 2.4Mhz (400 FSB) CPU and single stick of DDR for 512 MB. I've also got the new Antec Aria Case that has 300W PSU.
I installed everything and the PC did not boot. It did not go through POST. So, I removed everything and running with the minimum setup i.e CPU, Memory only. I get nothing on the display.
Can somebody help me in understanding what could be wrong.
Thanks

I'm using the on-board video connection. I also tried out with ATI9000AIW with no luck.
Power Signature
+5V - 26A
+12V - 18A
+3.3 - 28A
Yes, both the connectors are correctly connected. I use the same combination of components with my other SOYO motherboard and all works fine.

Similar Messages

Corrected FSB, now K7N2 won't POST - Need help!!

AMD XP 2600+ TBred B Core
1024 (2x512) MB PC3200 DDR SDRAM (Corsair XMS Series)
1 is C2 latency, 1 is normal PC3200. I had them both in channel A, right now I'm just running my brand new normal 3200 stick.
MSI GeForce6600GT (NX6600GT-VTD128SP)
MSI K7N2 Delta2 Platinum (MS-6570E)
Enermax 365P-VE PSU (350W, 3.3V & 5V rails have 32A each, 12V rail has 26A)
The system ran fine at the default settings, I installed Windows XP with no problems. No hardware difficulties, no overheating of any component, no lack of voltage. Everything was peachy keen, except that my XP 2600+ was being misdetected as an 2000+ because the FSB was being set at 133. So, I went into the BIOS and used the settings I know are correct for my processor, meaning the FSB was bumped to 166. Saved the settings to the CMOS and exited. Now, when my PC starts up, I am greeted with a black screen. No POST beep, no video, no nothing. CD-ROM spins up, hard drive spins up, all fans spin up, all lights light up, but...Nothing! First move -- Reset CMOS w/ jumper. Nothing! Next move -- Hard CMOS reset (1hr). Nothing. Next-move -- Barebones boot. More nothing. I even tried swapping out the video card just to be on the safe side. (it did nothing, of course) If I didn't know better, I'd swear it was a DOA board, except it was working fine for around 18 hours, and I heard the POST beep every time it started up, and the DRAM error 'continuous long beeps' when I first set it up & had the 3200C2 stick in the Channel B slot (which I can still hear if I try booting with the RAM removed). I found the "Insert" key trick, but it looks like my keyboard isn't even getting power. I've been completely unsuccesful in trying to undo my move to the 166FSB, and it seems this total failure to POST w/ this motherboard isn't a unique problem. Any help at all is GREATLY appreciated, as well as any explanation as to what in the HELL happened. This has left me utterly flummoxed. To reiterate -- my computer is in barebone state right now. (Motherboard, gfx card, processor, RAM, all power and case connected to mobo and gfx card, nothing else) Thanks. -David

... I have just experienced the very same problem as HorizonX! I'm using a AMD Athalon 2600+ processor in an MSI K7N2 Delta 2 - LSR mainboard with 2x512MB PC3200 DDR RAM chips and I decided (don't ask me why) to switch my front side bus frequency from 166Mhz to 200Mhz. Immediately after making the change my system, which had been working fine for about a month prior to this, failed to post - no beeps only the whirr and click of the hard drives starting up.
I attempted to clear the CMOS by moving the clear CMOS jumper to the "clear" position for a minute or two with no results. I then removed the battery and again set the clear CMOS jumper to "clear", this time for about five minutes, but once I returned the battery and the jumper to its original position the system still failed to post. I figured I must have fried my CPU and was ready to start shopping for a new one. Luckily I came across this discussion forum. After reading the previous comments about how long mainboard capacitors can hold charge I decided to try clearing the CMOS again using some of the forum suggestions. I unplugged my system, removed the battery, and moved the CMOS jumper to the clear position. I then toggled the power supply on and off a few times along with the front power button and then left the system to sit for a half an hour. After the half hour I toggled the power switches a couple of more times before I reconnected the power, reinstalled the battery, and restored the CMOS jumper to its original position. This time IT WORKED!! My CMOS was cleared and my system posted with default settings. Incidentally I did look for the FSB safe mode jumper on my mainboard but it doesn't appear to have one.
Unfortunately this my not be much help to HorizonX but I just wanted to let the other contributors know their advice helped solve my problem.

MSI Neo 2 plat w/ amd64 3200+ win will no longer post , need help plz.

Koolance watercooling case
enermax 431w ps
Msi neo2 plat with updated bios cant remember what version but i had to flash it as soon as i took it out of the box to be able to use sata raid trouble free.
amd 64 3200+ winchster 2ghz @ 2.6ghz
1gig (2x512) crosiar twinx DDR500 3.4.4.8
dual 36gig wd raptors in raid 0
sapphire x800xt
sb audigy 2
3 optical drives
floppy drive
6 80mm fans
System has been pretty much solid since i built it back in Dec 2005, The Power supply i've had for 1-2 years, last few months i would start up my pc and then at random between 15 secs or 30 mins the pc would just shut off, and sometimes it wouldn't do it at all. I didn't really think nothing of it. About a month ago i was about to play WoW (world of warcraft) and my pc glitched out and the sound screeched and then i shut it down, i reset the comp and no post, i then reset the cmos the pc then posted and i changed my bios settings back and i was up and running again. I could run any games, half life 2, quake 4, WoW and they all ran great i still got the random shut downs if it did shut down when i restarted it , it would shut down again. (odd) Tonight i was on chatting with some friends and was about to play some counter strike then changed my mind and i started up WoW everything loaded up great, got into the game and played for about 2 mins then my screen went black and the sound screeched, the monitor had no signal and my pc was still running, so i turn the thing off and reboot, no post and no beep code. I proceeded to reset cmos and reboot still nothing i checked the D-bug thing and i was getting a processor intialize error, so i thought i fried my cpu, i took off the waterblock and pulled out the cpu cleaned it up reapplied AS5 and then re-seated the cpu, tried to boot and nothing, i then started to pull ram out and swap slots and single the sticks out and that did nothing. I then stripped my pc down to barebones reset cmos and used beap codes, with just cpu seated i got a ram error code, put in a stick of ram then i got a video card error code put in the vid card then i was back where i started, no beep code and the d-bug thing was hanging on processor initialization. It could be my cpu although in my other comp i swapped cpu, i put the enermax 431w into the other comp nf2 w/ amd 2500 barton and it posted and ran fine, although when i used the ps from the other system in the one thats not posting it would post either but it was only a 300w ps. I don't believe its the cpu, the 20pin connector on the power supply has about 4 pins where the pastic shell has browned from heat or something, so i should replace the ps regardless but i'm not positive thats whats causing my issue. Anyone with any suggestions i'll pretty much try anything at this point.
Thanks for taking the time to read through my problem.

Quote
the 20pin connector on the power supply has about 4 pins where the pastic shell has browned from heat or something
This is not a good sign, this could be an indication of to much amp being drawed.
This could be due to a poor connection on the P/S connector or the connector of the MB or it could be due to a device like your CPU, ram, graphic card or so on drawing to much amps.
Check the MB for any signs of swelled, leaking or bursted caps, also look around the MB P/S connector for any resistors that have changed colors or are burnt.

Need help with conditional query

guys this is just an extension of this post that Frank was helping me with. im reposting because my requirements have changes slightly and im having a hell of a time trying to modify the query.
here is the previous post.
need help with query that can look data back please help.
CREATE TABLE "FGL"
    "FGL_GRNT_CODE" VARCHAR2(60),
    "FGL_FUND_CODE" VARCHAR2(60),
    "FGL_ACCT_CODE" VARCHAR2(60),
    "FGL_ORGN_CODE" VARCHAR2(60),
    "FGL_PROG_CODE" VARCHAR2(60),
    "FGL_GRNT_YEAR" VARCHAR2(60),
    "FGL_PERIOD"    VARCHAR2(60),
    "FGL_BUDGET"    VARCHAR2(60)
)data
Insert into FGL (FGL_GRNT_CODE,FGL_FUND_CODE,FGL_ACCT_CODE,FGL_ORGN_CODE,FGL_PROG_CODE,FGL_GRNT_YEAR,FGL_PERIOD,FGL_BUDGET) values ('240055','240055','7600','4730','02','11','00','400');
Insert into FGL (FGL_GRNT_CODE,FGL_FUND_CODE,FGL_ACCT_CODE,FGL_ORGN_CODE,FGL_PROG_CODE,FGL_GRNT_YEAR,FGL_PERIOD,FGL_BUDGET) values ('240055','240055','7240','4730','02','10','1','100');
Insert into FGL (FGL_GRNT_CODE,FGL_FUND_CODE,FGL_ACCT_CODE,FGL_ORGN_CODE,FGL_PROG_CODE,FGL_GRNT_YEAR,FGL_PERIOD,FGL_BUDGET) values ('240055','240055','7240','4730','02','10','1','0');
Insert into FGL (FGL_GRNT_CODE,FGL_FUND_CODE,FGL_ACCT_CODE,FGL_ORGN_CODE,FGL_PROG_CODE,FGL_GRNT_YEAR,FGL_PERIOD,FGL_BUDGET) values ('240055','240055','7600','4730','02','11','1','400');
Insert into FGL (FGL_GRNT_CODE,FGL_FUND_CODE,FGL_ACCT_CODE,FGL_ORGN_CODE,FGL_PROG_CODE,FGL_GRNT_YEAR,FGL_PERIOD,FGL_BUDGET) values ('360055','360055','7200','4730','02','10','1','400');
Insert into FGL (FGL_GRNT_CODE,FGL_FUND_CODE,FGL_ACCT_CODE,FGL_ORGN_CODE,FGL_PROG_CODE,FGL_GRNT_YEAR,FGL_PERIOD,FGL_BUDGET) values ('360055','360055','7600','4730','02','10','1','400');
Insert into FGL (FGL_GRNT_CODE,FGL_FUND_CODE,FGL_ACCT_CODE,FGL_ORGN_CODE,FGL_PROG_CODE,FGL_GRNT_YEAR,FGL_PERIOD,FGL_BUDGET) values ('240055','240055','7240','4730','02','10','14','200');
Insert into FGL (FGL_GRNT_CODE,FGL_FUND_CODE,FGL_ACCT_CODE,FGL_ORGN_CODE,FGL_PROG_CODE,FGL_GRNT_YEAR,FGL_PERIOD,FGL_BUDGET) values ('240055','240055','7600','4730','02','10','14','100');
Insert into FGL (FGL_GRNT_CODE,FGL_FUND_CODE,FGL_ACCT_CODE,FGL_ORGN_CODE,FGL_PROG_CODE,FGL_GRNT_YEAR,FGL_PERIOD,FGL_BUDGET) values ('240055','240055','7240','4730','02','10','14','200');
Insert into FGL (FGL_GRNT_CODE,FGL_FUND_CODE,FGL_ACCT_CODE,FGL_ORGN_CODE,FGL_PROG_CODE,FGL_GRNT_YEAR,FGL_PERIOD,FGL_BUDGET) values ('240055','240055','7240','4730','02','10','2','100');
Insert into FGL (FGL_GRNT_CODE,FGL_FUND_CODE,FGL_ACCT_CODE,FGL_ORGN_CODE,FGL_PROG_CODE,FGL_GRNT_YEAR,FGL_PERIOD,FGL_BUDGET) values ('240055','240055','7240','4730','02','11','2','600');
I need to find the greatest grant year for the grant by a period parameter.
once i find the greatest year i need to check the value of period 14 for that grant for the previous year and add it to the budget amount for that grant. however if their is an entry in the greatest year for period 00 then i need to ignore the period 14 of previous year and do this calculation current period +(current period - greatest year 00)
hope that makes sense so in other words with the new data above. if i was querying period two of grant year 11. i would end up with $800
because the greatest year is 11 it contains a period 0 with amount of $400 so my total should be
period 2 amount $ 600
period 0 amount $ 400 - period 2 amount of $600 = 200
600+200 = $800
if i query period 1 of grant 360055 i would just end up with 800 of grnt year 10.
i have tried to modify that query you supplied to me with no luck. I have tried for several day but im embarrased to say i just can get it to do what im trying to do .
can you please help me out.
here is the query supplied by frank kulash who gracefully put this together for me.
WITH     got_greatest_year     AS
     SELECT     fgl.*     -- or whatever columns are needed
     ,     MAX ( CASE
                 WHEN fgl_period = :given_period
                 THEN fgl_grnt_year
                END
              ) OVER ()     AS greatest_year
     FROM     fgl
SELECT     SUM (fgl_budget)     AS total_budget     -- or SELECT *
FROM     got_greatest_year
WHERE     (     fgl_grnt_year     = greatest_year
     AND     fgl_period     = :given_period
OR     (     fgl_grnt_year     = greatest_year - 1
     AND     fgl_period     = 14
;Miguel

Hi, Miguel,
Are you waying that, when the greatest year that has :given_period also has period='00' (or '0', or whatever you want to use), then you want to double the budget from the given_period (as well as subtract the budget from the '00', and not count the pevious year's '14')? If so, add another condition to the CASE statement which decides what you're SUMming:
WITH     got_greatest_year     AS
     SELECT       TO_NUMBER (fgl_grnt_year)     AS grnt_year
     ,       fgl_period
     ,       TO_NUMBER (fgl_budget)     AS budget
     ,       MAX ( CASE
                   WHEN fgl_period = :given_period
                   THEN TO_NUMBER (fgl_grnt_year)
                  END
                ) OVER ()     AS greatest_year
     FROM       fgl
,     got_cnt_00     AS
     SELECT     grnt_year
     ,     fgl_period
     ,     budget
     ,     greatest_year
     ,     COUNT ( CASE
                   WHEN grnt_year     = greatest_year
                   AND       fgl_period     = '00'
                   THEN 1
                     END
                ) OVER ()          AS cnt_00
     FROM    got_greatest_year
SELECT       SUM ( CASE
                    WHEN grnt_year     = greatest_year                    -- New
              AND       fgl_period     = :given_period                    -- New
              AND       cnt_00     > 0            THEN budget * 2     -- New
                    WHEN grnt_year     = greatest_year
              AND       fgl_period     = :given_period       THEN budget
                    WHEN grnt_year     = greatest_year
              AND       fgl_period     = '00'            THEN -budget
                    WHEN grnt_year     = greatest_year - 1
              AND       fgl_period     = '14'
              AND       cnt_00     = 0            THEN budget
                END
           )          AS total_budget
FROM       got_cnt_00
;You'll notice this is the same as the previous query I posted, except for 3 lines maked "New".

Need help in creating custom reports

hello,
I am using EM 10.2.0.2 on windows 32-bit.
All EM components are installed on a single machine.
Have installed AGENT 10.1.0.5 for managing targets which are on LINUX 2.1
Please help me in getting the solution for the following queries:
(a)I need to create a custom report regarding the CAPACITY MANAGEMENT .
(b)I have some UDM defined but I am not able to use these UDM while creating custom report.
(c)Also is there any possibility that we can use views other than REPOSITORY VIEWS. What I meant was : instead of using REPOSITORY VIEWS can we use the tables of the target instances.
Thanks in advance.

Same post
Need help on repository views for creating custom capacity planning reports

Need help in Mitigation...

Hi , I have the CC 5.2 connected to single system and using GLOBAL ruleset.
In backend i have created a role Z:CONFLICTING_ROLE and assigned to user ERIC.
Now there are two risks in the role F030 and S027 , i have created two mitigating controls for them and have mitigated the risks at role level .
When i run the report on the USER ERIC , it should show in there also as mitigated , but there is nothing in mitigation.
I was under impression that roles once mitigated , users with be mitigated also, what is wrong here ? ?
The option under Configuration :
Risk Analysis ->Add Options -> Include Role/Profile Mitigating Controls in User Analysis
is set to yes..
Pls help me to resolve this issue.
regds
navdeep
Edited by: navdeep pathania on Aug 25, 2008 11:02 PM

navdeep,
I was rather talking about the PFUD in the back-end system.
But okay, if the synch with GRC is not working in the first place, then this issue should be addressed as well. However, that goes beyond this particular post 'Need help in Mitigation"
In an attempt to help you : is your diamond shaped adapter green ? are you using the correct model in the JCO in terms of your release of backend system ? did you do a full sync or incremental ?
for sure, this is your issue why the users are not mitigated through their assigned mitigated roles.
succes
sam

Need help using dbms_scheduler to submit an immediate job on the database

Hi. I need help using dbms_scheduler to submit an immediate job on the database. Essentially I want to issue a one-time call to an Oracle Stored Procedure - this procedure will then send an email. I've never used dbms_scheduler before, but here's what I have so far.
So my Program is a stored database procedure named 'TTMS.dropperVacationConflict_Notify', but my problem is that I need to pass 3 parameter values to this job each time I run it. This is what I can't figure out. The procedure expects an 'Id' as number(5), begin_dt as a date, and end_dt as a date.
How do I pass these values when I run my job? Can anyone help?
begin
    dbms_scheduler.create_program(program_name=> 'PROG_DROPVACCONFLICTS_NOTIFY',
     program_type=> 'STORED_PROCEDURE',
     program_action=> 'TTMS.dropperVacationConflict_Notify',
     number_of_arguments => 3,
     enabled=>true,
     comments=> 'Procedure to notify PCM of a Dropper Vacation Conflict. Pass in Dropper Id, Begin_dt, and End_dt');
end;
begin
    dbms_scheduler.create_schedule
    (schedule_name=> 'INTERVAL_EVERY5_MINUTES',
     start_date=> trunc(sysdate)+18/24,
     repeat_interval => 'freq=MINUTELY;interval=5',
     end_date => null
     comments=> 'Runtime: Every day all 5 minutes, forever'
end;
begin
    dbms_scheduler.create_job
    (job_name => 'JOB_DROPVACCONFLICTS_NOTIFY',
     program_name => 'PROG_DROPVACCONFLICTS_NOTIFY',
     schedule_name => 'INTERVAL_EVERY5_MINUTES',
     enabled => true,
     auto_drop => true,
     comments => 'Job to notify PCM of Dropper Vacation Conflicts'
end;
/And I use this to execute the job as needed...
begin
    dbms_scheduler.run_job('JOB_DROPVACCONFLICTS_NOTIFY',true);
end;
/

Duplicate Post
Need help using dbms_scheduler to submit an immediate job on the database

Need help how to upload a PDF to an internet site

I'm applying for jobs on my iphone 5 and some websites need me to upload a resume... I click upload and my photo album comes up! I have PDFs of my resume saved on an app but I can't work out how to upload them on the websites? Any1 know an App or solution

Duplicate post NEED HELP: HOW TO OPEN A PDF IN ESS (EMPLOYEE SELF SERVICE)
--Shiv

Need help in posting a Form

Hi Everybody,
I'm having a Struts application that uses DynaValidatorForm for performing Validations.
The basic flow is like this -> I've got a home page, then a login page (action -> register.do) & a third page (action -> authenticate.do) which is displayed after authenticating the user.
I'm trying to re-direct the user to the home page once he directly accesses /authenticate.do
For this, in the Action class of /register, I'd defined a session attribute & set a value to it.
Then, in the Action class of /authenticate, I'm checking for the session attribute. If not present, I'm re-directing the user to home page.........
The problem that I'm facing is that when I directly access /authenticate.do, the application is not getting re-directed & instead, it is displaying error messages that User name & password (the 2 fields present in my login page) are required..........
The <action> tag of /authenticate.do has got validate="true" & hence it seems that validation occurs before re-directing....
Therefore, can someone tell me why is the application not posting the form to Action class of /authenticate........
Thanx in advance.....
Regards,
Sasidharan N

<form name="input" method="get" action=""> 
<table cellspacing="0" cellpadding="0" border="0"
width="300">
<tr>
<td><label for="proj_root">PROJECTROOT:
</label></td>
<td><input type="text" size="50" name="proj_root"
id="proj_root"></td>
</tr>
<tr>
<td><label for="frontend">FRONTEND:
</label></td>
<td><input type="text" size="50" name="frontend"
id="frontend"></td>
</tr>
<tr>
<td colspan="2" align="center"><input type="submit"
name="submit"
id="submit" value="Submit" onclick="save()"></td>
</tr>
</table>
</form>
(your form needs an action attribute value)
Murray --- ICQ 71997575
Adobe Community Expert
(If you *MUST* email me, don't LAUGH when you do so!)
==================
http://www.projectseven.com/go
- DW FAQs, Tutorials & Resources
http://www.dwfaq.com - DW FAQs,
Tutorials & Resources
==================
"goober35" <[email protected]> wrote in
message
news:gcjmlh$p42$[email protected]..
> Hello,
> I am new in writing HTML code. I need help to align my
Form and it's text.
> Please view my code and please show me how to align all
the square boxes
> (the
> square box is where the user type the text input).
Currently I have 2
> boxes but
> they are not aligned. The below is my code:
>
> <FORM name="input" method="get" >
> PROJECTROOT: <INPUT TYPE=TEXT SIZE=50
NAME=proj_root> <br>
> FRONTEND: <INPUT TYPE=TEXT SIZE=50 NAME=frontend>
<br>>
> <BR>
> <INPUT TYPE=SUBMIT VALUE=Submit onclick="save()">
<BR>
>
> </FORM>
>
>
> Would you please help.
>
> Thank you very much
> Goober35
>
>
> <FORM name="input" method="get" >
> PROJECTROOT: <INPUT TYPE=TEXT SIZE=50
NAME=proj_root> <br>
> FRONTEND: <INPUT TYPE=TEXT SIZE=50 NAME=frontend>
<br>>
> <BR>
> <INPUT TYPE=SUBMIT VALUE=Submit onclick="save()">
<BR>
>
> </FORM>
>

Need help with Apps misbehaving and upgrading the MacOS: The all-in-one post. ;)

Hi there,
So, I've been browsing the SL and Mavericks forums for the last days but although I have fetched some useful tips and answers, still need some help. Let me put it diary-style so I can be more concise ;)
Here's my current system profile:
iMac 27" (aluminium back- if I'm no wrong, from around late 2009-mid 2010)
MacOS 10.6.1 Never updated.
3.06 Ghz Intel Core2 Duo
4Gb RAM
LaCie Big Disk via FireWire 800
Internet access via Ethernet port (cable)
And here's The Issues Log:
– Day one: First ever Kernel Panic. Restart. Nothing (apparently) wrong.
– 3 weeks elapsed: Second Kernel Panic. Same. iMac restarts fine. Apps fine. No missing files. No misbehaviour experiences.
– After a month or so: One morning, Skype decides on its own to stop launching. The night before, I chatted with one of my clients, fine as always, but at the next day, nothing. Computer is usually shut off for the night. And so it was that night. Updated Skype and also did all the guest account trick / repaired permissions / repair ACLs. Nothing worked. Overwrote the Skype app with a former functioning version I have in an MacOS 10.5 system. Didn't work. Now I have to chat on the MacOS 10.5 computer. No good.
– 15 days ago or so: After realising that I no longer have my HP1515n printer (it ran out of inks and thrashed it. It costs more to refill than to buy a new one), I deleted the printer from the printers list in the System Prefs Pane.
– Last week: Acrobat (CS4) won't launch a PDF file and freezes. Spinning beach ball. Force quit and try opening the PDF file again. Freezes again. And again. And again. With that file and every other PDF.
Photoshop CS5 fails to open or crashes when attempting to open any jpg or tiff file. InDesign and Illustrator CS5 are frozen and had to force quit both. MacOS 10.5
Restart the iMac thinking it is just a "common" bad day and hoping everything will be alright after the restart, but nope.
Not only the CS5 stops working; MSOffice stops working too. Spinning beach ball. Begin to suspect of the deletion of the printer, however, I also deleted the same printer in the above mentioned 10.5 system and I'm not experiencing anything strange. Reinstalled the HP drivers but nothing remarkable happens.
Then, try to uninstall CS5, CS4, Office, etc. Try to reinstall Acrobat CS4 and the CS5 apps. Reinstall Office. Nothing. Just Outlook works.
Since I had to desperately meet deadlines, convinced a colleague to come over to the studio and -I know, I know- allowed me to install a copy of CS6. It seems to work fine, except for Acrobat, which randomly freezes/hangs/works and Photoshop, which works fine unless you want to open a layered file containing text layers or if you want to type text on a normal file, because it freezes as soon as the Text Tool is pressed in the toolbar, of course, spinning beach ball again.
Well, Illustrator CS6 sometimes shows a strange black thin frame overlaid on the interface but goes away by switching to another workspace and then back to the current. InDesign CS6 seems to be fine and making PDFs as expected. However, as I said before, it is pure luck if Acrobat accepts to open the file or even if it launches. Spinning beach ball when freezing/hanging.
As a method for eliminating possible culprits, did a clean up of the Suitcase Fusion database, removed duplicate and a few (less than 10) corrupted fonts.
Removed completely MSOffice reinstalled and updated. Nothing. Now I neither have MSoffice running.
I am no rookie but I can't even imagine what can cause such amount of misbehaviour, (kernel panics have something to do? malware? lack of system updates? MacHD is damaged?) so I'm thinking of a few scenarios:
Backing up my projects and user folder –anything else to backup? (In fact I've already done that)– and:
1. Do a clean install. Not sure if it will be best to completely erase the whole drive or if a standard reinstallation will be enough.
2. Take the machine to a Genius Bar to see if there's anything that can be done without major OS messes.
3. Erase the drive and go through the Mavericks upgrading (SL to Ln to MLn to Mavcks), although not sure if this upgrade is worth yet.
4. Replace HD for a brand new one and either step 1 or 3.
5. As a complement, I'm thinking of adding more RAM.
Well. It is really the first time I don't know what to do. I have work to do and would not want to face a week away from my main computer and since most of the files are CS5-6 and hence, can't move to my wife's iMac...
Apologies if this post feels too long, but I will truly appreciate any kind of input and advice on one of more of the issues mentioned in this post.
And if it fits best in any other forum, please also let me know.
Cheers and thanks in advantage.

You have to use the Base Station Menu on the Menu Bar at the very top of your screen.
Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
I am employed by HP

Installation of Photoshop update 13.1.2 for creative cloud fails with error code U44M1P7 I need help

I need help installing update 13.1.2 for Photoshop creative cloud, installation fails with error code: U44M1P7. Could someone please help?

Sorry to bother you.
I could find the answer after searching previous posts about this language problem.
Had to change my language in AAM profile and then download PS CS6 again ( english version ).
Then open the actual Photoshop and in preferences > interface you can besides the Dutch also option for English.
restart application and Voila.
Greetz, Jeroen

If i reset my ipad can i install paye games for free if i sign back into my apple ID. Please i need help because i need to update my games but i need to put in this billing thing and i want to get rid of it so then i cant buy games with my credit card

If i reset my ipad can i install paye games for free if i sign back into my apple ID. Please i need help because i need to update my games but i need to put in this billing thing and i want to get rid of it so then i cant buy games with my credit card

Hello,
As frustrating as it seems, your best to post any frustrations about the iPhone in the iPhone discussion here:
https://discussions.apple.com/community/iphone/using_iphone
As this discussion is for iBook laptops.
Best of Luck.

Need help in writing a vbscript

Hi,
I need help in wring a vbscript. I have serached for the vbscript on the net, but could not find any.
I need to add a file to an msi using vbscript. - That's the requirement.
For this I have done the following with the help of vbscript.
1. With the insert statement I inserted a new copmonent in the FeatureComponent Table.
2. Now the next thing I did is, I inserted a new row in the File table using insert statement again. The file is uncompressed.
3. Since the file is a non-version file I also added a row in the MSIFileHash table.
4. Also, now added the Component in the component table.
After doing this I am able to see the chnages in the mst, however whrn I try to install it I get an error 2725 (Invalid database tables).
Can somebody please post a vbscript which can add a file to an msi?

Hi All,
Thanks for all your responses.
Yes, It is not so easy. I never said it was. Thanks for pointing out Orca. We use Orca on a daily basis.
What exactly I am looking at, is this.
We have some standard applications which needs to be repackaged every month. The repackaging process is same and does not change at least for these packages. So I was actually looking at automating these things.
What I did so far.
First we have created an object for Windows installer. I have then taken a copy of the original msi and then opened the database of this temporary msi database in transact mode. Once the database is opened we can use select, insert, update
and delete statements to update the database.
I could successfully add a registry to the msi. The component was also added successfully to the component table. I also could make changes to the Property table.
The tricky part comes with the addition of file to the file table.
The addition of file requires the following steps.
1. Add a new row to the file table. This can be done with the Insert statement.
2. We then need to associate the file to a new component or any other component already existing in the msi. In my case I am creating a new component.
3. We then have to associate this components to a feature in the FeatureComponents table.
4. Since the file I am adding is a non-versioned file, a new row also has to be added to the MSIFILEHASH table.
I could see the changes that I have done using the mst. But when I try to install the msi with the mst, I get the error 2725. I checked everything. All the other steps except for the file addition works fine.
To check whether I am indeed right, I have did this.
Skipped the file addition part to the msi. Every other change that I make works and I am able to install the msi with the mst successfully.
For obvious security reasons I will not be able to share the vbscript with you. If you guys think, that this is not a right forum for this question, please let me know the right forum. I have been stuck with this issue from the past 6 months. Any help would
really be appreciated.

Need help in alignment a form

Hello,
I am new in writing HTML code. I need help to align my Form
and it's text.
Please view my code and please show me how to align all the
square boxes (the square box is where the user type the text
input). Currently I have 2 boxes but they are not aligned. The
below is my code:
<FORM name="input" method="get" >
PROJECTROOT: <INPUT TYPE=TEXT SIZE=50 NAME=proj_root>
<br>
FRONTEND: <INPUT TYPE=TEXT SIZE=50 NAME=frontend>
<br>>
<BR>
<INPUT TYPE=SUBMIT VALUE=Submit onclick="save()">
<BR>
</FORM>
Would you please help.
Thank you very much
Goober35

<form name="input" method="get" action=""> 
<table cellspacing="0" cellpadding="0" border="0"
width="300">
<tr>
<td><label for="proj_root">PROJECTROOT:
</label></td>
<td><input type="text" size="50" name="proj_root"
id="proj_root"></td>
</tr>
<tr>
<td><label for="frontend">FRONTEND:
</label></td>
<td><input type="text" size="50" name="frontend"
id="frontend"></td>
</tr>
<tr>
<td colspan="2" align="center"><input type="submit"
name="submit"
id="submit" value="Submit" onclick="save()"></td>
</tr>
</table>
</form>
(your form needs an action attribute value)
Murray --- ICQ 71997575
Adobe Community Expert
(If you *MUST* email me, don't LAUGH when you do so!)
==================
http://www.projectseven.com/go
- DW FAQs, Tutorials & Resources
http://www.dwfaq.com - DW FAQs,
Tutorials & Resources
==================
"goober35" <[email protected]> wrote in
message
news:gcjmlh$p42$[email protected]..
> Hello,
> I am new in writing HTML code. I need help to align my
Form and it's text.
> Please view my code and please show me how to align all
the square boxes
> (the
> square box is where the user type the text input).
Currently I have 2
> boxes but
> they are not aligned. The below is my code:
>
> <FORM name="input" method="get" >
> PROJECTROOT: <INPUT TYPE=TEXT SIZE=50
NAME=proj_root> <br>
> FRONTEND: <INPUT TYPE=TEXT SIZE=50 NAME=frontend>
<br>>
> <BR>
> <INPUT TYPE=SUBMIT VALUE=Submit onclick="save()">
<BR>
>
> </FORM>
>
>
> Would you please help.
>
> Thank you very much
> Goober35
>
>
> <FORM name="input" method="get" >
> PROJECTROOT: <INPUT TYPE=TEXT SIZE=50
NAME=proj_root> <br>
> FRONTEND: <INPUT TYPE=TEXT SIZE=50 NAME=frontend>
<br>>
> <BR>
> <INPUT TYPE=SUBMIT VALUE=Submit onclick="save()">
<BR>
>
> </FORM>
>

Need help in creating a 16gray levels 4 bit IndexColorModel.

Hi ppl,
Really need help with the above mentioned. I have reduced a 256 gray level .PGM image to 16 gray level (not using JAI). However, I'm having lots of trouble trying to create the image. It always comes out too dark. Does anyone know what the problem may be? Could it be that I'm using the wrong ColorModel?
Am currently using the follow code
static {
grayPallete1=new byte[16] ;
for(int i=0; i<16; i++) grayPallete1=(byte)i ;
public ImageData(byte[] pmap, int r, int c){
bpels = pmap ; irow=r; icol=c;
     int i = 0;
     clrmdl= new IndexColorModel(4,16,grayPallete1,grayPallete1,grayPallete1) ;
Any help is greatly appreciated!
Rgds,
Dam
Message was edited by:
Damy
Message was edited by:
Damy

Hi Suman Sarkar,
I am a little confused about the layout of your waterfall chart, could you please post some dummy chart here, with a clear
understanding with the issue, we could give some solution or workarounds, the steps of uploading the picture are following:
1.
Upload the picture to a website
http://skydriver.live.com
2.
View the picture in the website.
3.
Right-click the picture, and then select “Copy”
4.
In reply window, select “Paste” to paste the picture into a post.
If you have any question about the steps, please feel free to ask.
Regards,
Challen Fu

NO POST - Need Help

Similar Messages

Maybe you are looking for