No POST with more than 2 RAM slots?

Hello community! Yuu are my last hope.
I recenly purchased the MSI X99S and tried to install 4x4GB Crucial Ballistix DDR4, but it wont work. It does work with only 2 Sticks. I verified that the RAM is not broken, though. I also used the required quad-channel DIMM-Slots. Anyone else having this problem and a potential fix? Currently I can only use 8 GB.

Hello! Thank you for the answer. I have the X99s SLI Plus Motherboard. I tried it and the result is, that my PC only boots when the RAM is inserted in DIMM 1 and 3. Is it supposed to work in every single slot? Because it doesnt even work if I put one each in DIMM 1-4.

Similar Messages

  • P67A-GD65B3 won't post with more than 2 RAM sticks/P

    Issue is as stated.  On this board the dimm slots are listed as 1,2,3,4 (as marked on motherboard).  The computer will consistently power cycle (not even post) when RAM is in any dual channel configuration.  I've tried 4 sticks of memory (2 separate orders of 2x4GB).  All RAM sticks work in non-dual channel mode.  I've modified the voltage to 1.65.  I've verified the timings are correct at 8-8-8-24.  I've inserted 1 stick at a time, let boot all the way to windows, and inserted the next stick.  I tried the inserting 1 at a time numerous different ways.  Anything else I may have missed?  If not, I guess its RMA time.

    Quote
    2 separate orders of 2x4GB
    Check with G.Skill. I believe they only warranty & suggest one kit being installed. Differences in batches are noted as the excuse if memory serves me. UEFI/BIOS version 1.D was released by MSI to accomodate the non standard SPD profile programming, since a newer one, 1.E is installed, it rules a problem there out. It's also possible the RAM requires X.M.P. to be enabled to make them work correctly. Again, G.Skill is going to be the best source for advice on how to get their product to work.

  • Problems deploying Windows 7 x64 computers with more than 8GB RAM

    SCCM 2012 R2 CU1
    Windows 7 x64
    We have a weird problem after upgrading from SP1 to R2 CU1. We have built a Windows 7 64 bit image with the latest updates (currently September 2014 updates). It deploys fine to all computers. But after some days – don’t know exactly – guess after 4-7 days
    - we start getting errors on computers with more than 8 GB of RAM. The errors just start out of the blue. We didn't change TS, image or driver package.
    The error shows in 3 different ways – depending of the computer model.
    1) BSOD – STOP 0x000000F4. Disk error.
    2) Task Sequence error 0x87D00269 when installing the first Application in TS. The error seems to have something to do with Management Point not found.
    3) Task Sequence simply stops after installing CMclient. No errors - it simply stops.
    For instance we get the BSOD on the Lenovo ThinkCentre M93p. But on the ThinkCentre M83 we get the TS error 0x87D00269. M93p and M83 uses the same driver package. They consequently  fail every time after the error has begun. If we reduce (remove physically)
    the memory to max. 8GB of RAM, they successfully run the Task Sequence.  We get the above errors on both Lenovo and HP machines with more than 8GB. 
    I made a copy of the production TS and started testing. I created a new driver package for M93p/M83. It contains only the NIC drivers. Now M93p an M83 successfully finishes the TS. Adding sata or chipset or MEI/SOL drivers to the package I get the 0x87D00269
    error on both m93p and M83. At least not the BSOD on the M93p ;-)
    Tried setting  SMSTSMPListRequestTimeout to 180 in the TS. Also tried putting in a 5 minute break before installing the first Application in the TS. Also tried putting in SMSMP=mp1.mydomain in the installation properties for the CMclient. It is still
    the same problem.
    Investigating the smsts.log on a computer with the 0x87D00269 error.
    Policy Evaluation failed, hr=0x87d00269 InstallApplication
    25-09-2014 08:59:59 3020 (0x0BCC)
    Setting TSEnv variable 'SMSTSAppPolicyEvaluationJobID__ScopeId_654E40B7-FC55-4213-B807-B97383283607/Application_d9eea5a0-0660-43e6-94b8-13983890bae2'=''InstallApplication 25-09-2014 08:59:59 3020 (0x0BCC)
    EvaluationJob complete InstallApplication25-09-2014 08:59:59 3020 (0x0BCC)
    MP list missing in WMI, sending message to location service to retrieve MP list and retrying. InstallApplication 25-09-2014 08:59:59 3020 (0x0BCC)
    m_hResult, HRESULT=87d00269 (e:\qfe\nts\sms\client\osdeployment\installapplication\installapplication.cpp,1080) InstallApplication
    25-09-2014 08:59:59 3020 (0x0BCC)
    Step 2 out of 2 complete InstallApplication 25-09-2014 08:59:59 3020 (0x0BCC)
    Install application action failed: 'SCIENCE PC Guide'. Error Code 0x87d00269 InstallApplication 25-09-2014 08:59:59 3020 (0x0BCC)
    Sending error status message InstallApplication 25-09-2014 08:59:59 3020 (0x0BCC)
     Setting URL = http://mp1.mydomain, Ports = 80,443, CRL = false InstallApplication 25-09-2014 08:59:59 3020 (0x0BCC)
    Investegating the 0x87D00269 error on the siteservers Status Messages Queries is weird.
    Install Static Applications failed, hr=0x87d00269. The operating system reported error 617: You have attempted to change your password to one that you have used in the past. The policy of your user account does not allow this. Please select a password that
    you have not previously used.
    Hopefully this is a bug in translating the errorcodes? Just to be sure I checked all the SCCM serviceaccounts and none of them have expired passwords.  And again why only on computers with more than 8GB RAM.
    Anyone else had problems rolling computers with more than 8GB og RAM?
    Why does this happens after a few days? To begin with, it runs just perfect and then starts failing on all machines with more than 8GB. Without a change in TS, image and driverpackage. We have seen this pattern for the last 3 month after
    updating our image with the latest Windows Updates. It all started after updating from SP1 to R2 CU1.
    Why does it only affect machines with more than 8GB RAM?
    How to get rid of the 0x87D00269 error?
    Seems to be somehow related to driver installation mechanism in SCCM in combination with Windows 7 64 bit, +8GB RAM and SCCM 2012 R2 CU1 or perhaps just R2.
    Any help or hints would be appreciated!
    Thanks
    Anders

    We have the same workaround, using a x64 boot image resolved all our issues with WinPE 5.0.
    Machines with >4GB of RAM
    Lenovo ThinkPad T540p failed applying drivers with 80040005
    Black screen/white cursor issues intermittently
    No updates from Microsoft, they are still looking through the logs, but we have updated our boot images and all is well now. Our case it still open with Microsoft, they are researching the logs.
    Daniel Ratliff | http://www.PotentEngineer.com

  • Successful install of 8.1.7 on Solaris 8 with more than 256Mb RAM

    To all who have struggled with this one, like me. You owe me a bottle of Rogaine.... but I will accept a bottle of Jack instead.
    It appears that the kernel parameters published in the Install Guide are only good for Solaris 8 with up to 256Mb RAM
    If dbassist craters at around 80% in OUI with a "Can't connect to Oracle" and you have more than 256Mb on board
    DOUBLE the kernel parameters !!!
    shmmni = 200
    shmseg = 20
    semmns = 400
    semmni = 200
    semmls =200
    semopm =200
    touch /reconfigure (they don't mention that in the Guide)
    reboot
    If someone out there can isolate which actual damn kernel parameter is the culprit, I will gladly share some Jack with you.
    Otherwise an email to [email protected] with a comment or three will suffice.
    Cheers

    Sorry to ask a dumb question, but want to be precise, whn you say touch/reconfigure, do you mean touch system.
    WHat is the reconfigure?

  • GeForce 7300 GT with more than 2GB RAM?

    I had a lot of crashes with my MP and had original 2x512MB & Kingston's 2x1GB installed.
    I contacted Kingston's support when Rember caused kernel panic every time I tried to test memory with it.
    They said that it is "known issue" that 7300gt does not work with current drivers with openGL applications and more than 2GB memory installed.
    But my MP kept having kernel panics with rember (and with lots of other applications)without any openGL involved. I even ran Rember with Finder closed.
    With only 2x512 or only 2x1 installed everything seems to be fine, except that there's not enough memory to use FCS efficiently.
    Anybody had same problems?
    Is this really "known issue"?
    If it is, when is solution available?
    MP+GF7300gt have been on the market over half a year now.
    Any links and references would be appreciated.
    I didn't find anything from apple's website and will be calling apple's support tomorrow...

    I have 4 GBs installed in my Mac Pro w/7300 card. No problems whatsoever.
    For best performance from quad-channel interleaving you may want to install either six additional 512 MB DIMMs (four in Riser A and four in Riser B) or two more 512 MB DIMMs (in Riser A) and four 1 GB DIMMs (in Riser B.)
    In your current configuration I believe you should have two 512 MB DIMMs in Riser A and two 1 GB DIMMs in Riser B.
    See Memory (FB-DIMM) Replacement Instructions.

  • Mac Pro 2.66 crashing with more than 2GB ram

    I curently have a base config of 1GB ram (2 512MB chips), the systems runs fine, I then added memory in various configs and it always kernel panics when I exceed 2 GB. System runs fine until i try something memory intensive like Aperture or Photoshop.
    tried
    4 x 512MB chips (2GB) = perfect
    6 X 512MB chips (3GB) = crash
    2 x 512MB and 2 x 2GB (5GB) = crash
    2 X 2GB (4GB) = crash
    I have tried only riser 1, still crashes even with only the 4GB running. All memory is genuine apple and passes the hardtest CD.
    Any help much appreciated
    cheers

    Agreed.
    If you cannont get the memory to fail when only one or two pairs is in a given riser then it will be very difficult to diagnose and you'd have to suspect either a riser or mainboard problem.
    You do know that memtest will only test up to 2GB unless you buy the $0.99 version 4.14 though right? Lower versions shouldn't KP though, should just allocate 2GB and test.
    If it fails in both the following combinations:
    Riser A - 2x 512
    Riser B - 2x512, 2x 512
    Riser A - 2x 512, 2x 512
    Riser B - 2x512
    then I suppose I'd be suspecting hardware failure on the motherboard. BY the way, both risers boards are identical, you can swap Riser A for Riser B and still have a working system if it helps in your tests.
    I just went through the same thing, fortunately I had only 2 pairs (2x1GB) to work with...so I labelled the chips ABCD and worked the combinations through the risers A and B to determine that failure followed a given FBDIMM....after I'd done all this and found the suspected FBDIMM, I powered up the machine with the cover off for a change and found the red lights...did I feel silly then

  • Please Help :( iMac 20" refuses to boot up with anymore than 1gb ram?

    Please Help iMac 20" refuses to boot up with anymore than 1gb ram?  It was fine 4 days ago and had been working with a 1gb stick in one slot and a 2gb stick, which had replaced the orignal 1gb stick that I got it with, in the other and it had shown 3gb of ram and was working just fine with that since November?  It went to sleep briefly 4 days ago while I was waiting on a customer and I came back to try to wake it up and it never would forcing me to hard boot it.  When I did that it would only go to a black screen with a solid white light on the power indicator.  Over and over again and same thing.  I read and tried every suggestion I could possibly find in this and a few other mac forums to no avail.
    I finally after reading about RAM issues etc.  I decided to power off and take out the ram sticks and try them one at a time in each slot.  So I took out the 2gb stick and did the SMC reset and it would boot up and work just fine with the 1 gb of ram.  So then I went through the same process with the 2gb stick and it would not boot up only go to a black screen with white solid light again (NOT flashing).  So then I tried the other original 1gb I had replaced with the 2gb and it worked just find like the other 1gb.  So then I tried just 1gb stick in the other ram slot (back facing one) and with just the 1gb strip it booted up and worked fine.  Tried it with the other 1gb stick and once again that one too worked just fine.  So I determined it wasn't the slot itself I thought?  I then tried the 2gb in the back slot and it would not boot only go to the black screen white solid light deal like before.  So I thought well ok it's obviously the 2gb ram must have somehow went bad (even though I have only had it since November) and I thought well I will just use the (2) 1gb sticks in each slot and then that will at least give me 2gb because only 1gb really ***** LOL.  So I proceeded to go through the same shut down process installed both sticks (I always push them to I feel them click and my fingers have a nice indention on them) reset the SMC and turned the power one and.... It would only go to the black screen with white solid light on power indicator????  I went through the same above process at least 3 times and again today a few times and I can't figure it out and I tried to search and search and I couldn't find anything like what I am experiencing.....What happened?  Please help this slow Imac is killing me.  It will work with 1gb ram only nothing more?  Here are the specifics of my Imac.
    It is a 20" Late 2006 Intel Core 2 Duo 2.16 ATI Radeon X1600 256 MB graphics card and Ram with now only 1gb (did have 3gb) and I am running OSX Lion 10.7.5
    When I go to system report and go under memory it shows this:
    BANK 0/DIMM0:
      Size:          1 GB
      Type:          DDR2 SDRAM
      Speed:          667 MHz
      Status:          OK
      Manufacturer:          0xCE00000000000000
      Part Number:          0x4D342037305432393533435A332D43453620
    BANK 1/DIMM1:
      Size:          Empty
      Type:          Empty
      Speed:          Empty
      Status:          Empty
      Manufacturer:          Empty
      Part Number:          Empty
      Serial Number:          Empty
    Any help I can get would really be appreciated.  Thanks in advance
    ALSO...Here is also a pic of the system log right before it happened.  It even changed the date to 07/2014????
    I have some more if needed??????????????? 
    <Personal Information Edited by Host>

    The Memtest just completed and came back like this?  It only test the single 1gb chip because anything more in this computer it won't go past the black screen with solid white power light. 
    Memtest version 4.22 (64-bit)
    Copyright (C) 2004 Charles Cazabon
    Copyright (C) 2004-2008 Tony Scaminaci (Macintosh port)
    Licensed under the GNU General Public License version 2 only
    NOTE: No command-line arguments have been specified
    Using defaults: Test all available memory, one test pass, no logfile
    Mac OS X 10.7.5 (11G63) running in multiuser mode
    Memory Page Size: 4096
    System has 2 Intel core(s) with SSE
    Requested memory: 250MB (263086080 bytes)
    Available memory: 250MB (263086080 bytes)
    Allocated memory: 250MB (263086080 bytes) at local address 0x0000000101000000
    Attempting memory lock... locked successfully
    Partitioning memory into 2 comparison buffers...
    Buffer A: 125MB (131543040 bytes) starts at local address 0x0000000101000000
    Buffer B: 125MB (131543040 bytes) starts at local address 0x0000000108d73000
    Running 1 test sequence... (CTRL-C to quit)
    Test sequence 1 of 1:
    Running tests on full 250MB region...
      Stuck Address       : ok             
      Linear PRN          : ok             
    Running comparison tests using 125MB buffers...
      Random Value        : ok
      Compare XOR         : ok
      Compare SUB         : ok
      Compare MUL         : ok
      Compare DIV         : ok
      Compare OR          : ok
      Compare AND         : ok
      Sequential Increment: ok
      Solid Bits          : ok             
      Block Sequential    : ok                
      Checkerboard        : ok             
      Bit Spread          : ok               
      Bit Flip            : ok               
      Walking Ones        : ok               
      Walking Zeroes      : ok               
    All tests passed!  Execution time: 362 seconds.
    logout
    [Process completed]
    Seems Okay I guess?

  • More than 2GB RAM 1st gen Macbook

    Is there any way possible to get more than 2GB RAM in a 1st gen macbook? I have one 2GB stick in right now but if I try to put even the old 512MB in the other slot I get no video. I also tried two 2GB sticks as well. I'm pretty sure the answer is no, but it doesn't hurt to ask and have hope
    I have a dell inspiron with Core2 and it wouldn't see 4GBs until I pulled the battery on it. maybe there is a trick for the macbook like that?

    I was hoping since it sees one 2GB stick it may like 2? It was a long shot. I just got this one used, so I'm stuck with it for a while. It runs fine with 2GB though.

  • P67S-C43: Won't POST with two sticks of RAM

    Hi, my new P67S-C43 has a peculiar problem: It won't POST with two sticks of RAM. I've tried both of my sticks (2 x 2GB G.Skill Ripjaws DDR3-1600 CL9 1.5V) individually in Slot 1 and the system POSTs fine. When I insert the second stick in any other slot, the system proceeds to restart unsuccessully a couple of times and then it will not POST. Only one blue LED is illuminated. When the system is in this state I have to reset the CMOS in order to POST successfully with a single stick of RAM again, which made the problem difficult to diagnose and very annoying to troubleshoot (lose BIOS settings after every attempt with the clear).
    Any idea of when we'll see a new BIOS? Are any betas available? I'd like to see if this is a BIOS problem before RMAing it.
    Thanks.

    Quote from: HU16E on 14-January-11, 16:52:36
    Which BIOS do you now have? Current official is V1.5. It would possibly help to have a full listing of all the systems components. Work with the one RAM stick initially in the primary dimm slot, blue closest to CPU. Get the OS loaded, drivers, etc., then add the second stick in the other blue dimm slot later. I have a feeling the RAM is setting itself up wrong. Might try the manual settings of 1333 9 9 9 24 @ 1.50V's.
    The BIOS was 1.5 out of the box but it's my understanding from another thread that there have been a slew of beta BIOSs released. I'm not going to load the OS until I get this straightened out. Also, both sticks would have the same settings with one stick or two installed. I fiddled with voltage, timings, etc but it still wouldn't work when I popped in the second stick. LIke I said, after every attempt with two sticks I have to clear CMOS or it won't work again with one stick. I'm hoping to try a newer BIOS before spending more hours on this, one setting at a time.
    Also, I have a 2600K but the rest of the components are irrelevant. At one point I had everything but the CPU/fan, video card, and RAM unplugged and the mobo entirely out of the case. Still didn't work until there was only one stick.

  • Anyone with more than one iPhone 6/6+ in same order getting there phones shipped if all your phones didn't have 9-19 when you ordered?

    Our Verizon account has 10 lines and I figure we're paying over $7,000 a year, when I think of how much money total we have payed to Verizon only to be jerked around and around and lied too over and over again really does make me sick.  6 of these contracts have ended and 3 will be up in next couple months and 1 has a year left so the cancelation fees would not be that bad. And with the other big carrier I've heard it might be cheaper on monthly service. All I wanted from Verizon was for them to do whats right.
    I Ordered
    iPhone 6 16gb  gray
    iPhone 6+ 16gb gray
    iPhone 6+ 64gb gray
    iPhone 6+ 64gb silver
    all on the same order. I finished at 3:19 am est and got a date of 10/14 even though all the phones except the 6+ 16 gb gray had 9/19. Got confirmation email at 4:56 will ship by 10/14 I got worried that all the phones would not ship till 10/14 and contacted verizon thru facebook messenger. They told me my phones would ship in the order received and not be held up by a phone that wasn't available in my order. And based on the time of my order she said 9/19 for the 6 and 6+ silver, 10/7 for the 6+ 64 gray , 10/14 for 6+ 16 gray. On Monday morning my status changed to 9/19:):) in the afternoon in changed to unknown. I called 611 and rep went thru all my phones with a time sheet she had and said i should get all but the 6+ 16 gray on 9/19, she said that one you had to order by 3:00 to get on 9/19. On Wednesday my status changed to 10/14 , called 611 again and this lady told me all my phones had 10/14 listed after them. She told me she didn't know  what to tell me that Apple ships the phones and its out of Verizon's hands because they don't have the phones. then she told me to call Apple (and gave me the phone # ) and see if they ship preorders with more than 1 in a order when their available or wait till all are. I called them ( they laughed that Verizon had me call them) and they don't hold up orders . Called customer service back and guy said at least 10 times ....I ASSURE YOU VERIZON WILL NOT HOLD YOUR PHONES!!!  i said of course they're not actually putting them in a box and waiting for all, they're sending them to other people who ordered after me. I asked him if my order could be separated/ rebuilt and do a (jump the line request)  so i could get my phones when i should. He said there is no such thing at verizon....he has worked there many years and if there was he would know. Someone posted # to Internet orders so i called them Thursday morning, spoke to a very nice guy he said my phones that i should get i would and i should get an e-mail later that day and if i didnt get anything by 8:00 pm to call back. Before we hung up i asked if I didn't  get anything did he know if they could cancel/separate/rebuild and do jump the line, he said they can do that and put me on hold while he spoke with a supervisor, he came back and said if nothing happened that day they would do that with my order. I got nothing, called Internet orders back at 8:30pm... went thru my history and asked them to do the rebuild. She transferred me to supervisor who REFUSED to rebuild my order, that is only for orders that have a technical error. She was also the first person from Verizon to tell me that they DO NOT  ship orders in multiple shipments, they will only send when everything is available. She then said your order was given a delivery date of before 10/14  and that's when you'll get all your phones. I let her know that there is nothing about that confirmation that tells me that the phones that I ordered that had 9/19 deliver by dates would not be delivered then, 9/19 is before 10/14.

    Same thing happened to me!!! They made a shady business move and they should be ashamed. Placed a pre-order for an Phone 6 and an iPhone 6 Plus at 2 AM on the 12th and got my pre-order in line just like everyone else did that morning. The 6 said delivery by 9/19 and the Plus was already back ordered to 10/7 but that's fine, I expected the Plus to be harder to get anyway. Being that both phones were eligible it made sense to just place one order given this hasn't been an issue in the past. However, Verizon moved my iPhone 6 pre-order delivery to coincide with the back ordered Plus so they don't have to ship each phone separately!!! I have to wait for something on backorder while the other is ready so they can save on shipping cost. I expected the one that I pre-ordered IN TIME FOR A 9/19 delivery and waited my turn "in (on)line" like everyone else I should get that when it told me that in the checkout, THEN send the Plus when it becomes available. I even have the confirmation email that says "Deliver by 9/19"!!!  Every company you order from sends you the backorder item when it becomes in stock, they don't wait and hold the entire order for it. WHAT A BUNCH OF CRAP!!!

  • Is there a stereo bluetooth headset that can pair with more than one device at a time?

    Is there a stereo bluetooth headset that can pair, i.e. multipoint, with more than one device at a time?
    Are the MacBook and iPhone 4 capable of multipoint bluetooth technoloagy?
    The goal is for my wife to be able to watch her Korean TV soap operas on her MacBook and still receive a call on her iPhone 4 via a stereo bluetooth headset.
    I was looking at the Motorola S10-HD but after further review saw that it only pairs with one device at a time.
    Appreciate any and all input. My Googling has returned no results.
    Rick

    TeslasBB wrote:
    pairing my BB8330 with my blue tooth earphone(TM:jawbone) and my microsoft sync thats in my car simultaneously? if i pair with the car, will i have to pair my jawbone all over again?
    You can only pair one device at a time to your 8330, or any other phone for that matter.  The "pairings" are saved to the phone, you can use one or the other and you won't have to pair it again.  Once you turn your bluetooth device on and the phone is on, they will find each other again.
    Hope this helps,
    John
    Stevie Ray! 1954-1990
    ** Don't forget to resolve your post with the accepted solution.

  • After soak test update, I get error messages repeatedly. The majority are "unfortunately, messaging has stopped", but you can replace messaging with "android os", or any other process, as it happens with more than just messaging. I have had numerous peopl

    After soak test update, I get error messages repeatedly. The majority are "unfortunately, messaging has stopped", but you can replace messaging with "android os", or any other process, as it happens with more than just messaging. I have had numerous people call and ask why I didn't reply to their texts...and I look, but have not received any new texts. YES, I have restarted phone. I have cleared data as well as cache on all apps. I have downloaded the vzw messaging app, which seems silly, since it happens with several different processes and apps, but all to no avail. I am missing texts from my employer, from my family. This did happen, but rarely, before this "soak test". It is now Kitkat version 19.6.3.obake_verizon.en.US. THIS is when I started having problems...like 50 times a day kind of problems! I have seen hundreds of posts all over the internet over the past 3 days. Does no one know how to fix this??? Shouldn't there be a way to revert phone to a pre-update state? and no, hard reset did NOT work!!!! I have been with verizon for well over 15 years, but I have not upgraded my lines and will not in July either. This is ridiculous. It's not like my games aren't working, it is my messaging and "android os"...my lifeline at work!

    kristinaf333,
    Oh no, I am sorry to hear your messages are not working since the software update. I greatlly appreciate doing all that troubleshooting to try and get the messaging application back in business. I know how much I rely on my messages so I can understand the urgency to get this resolved. Have you had a resolution ticket opened since you started experiencing issues with your messages? Does this happen with all contacts or just some? Please provide additional information to ensure we get to the bottom of this for you.
    KarenC_VZW
    Follow us on Twitter @VZWSupport

  • Can i use my ipod with more than one computer?

    i synched my ipod with one computer, hooked it up to another and it says i can't sync with more than one library? it says i have to restore it but i dont want to delete my music off of my ipod, i just want to add the music from this other library

    I have two different iPods and two computers. I regularly use either iPod on either computer.
    First set the preferences so itunes will not automatically sync when ipod is connected.
    Then connect the ipod and set itunes to manually manage music.
    Drag and drop whatever content you want to the device showing on the left.
    If this was the default setup, there wouldn't be all these posts about people losing all their music when they connect their ipod.

  • When texting with more than one person at a time the incoming text scrolls to top of the conversation. anyone out there with the same issue?

    while texting with more than one person at a time the incoming texts scrolls to top of conversation. anyone having this issue?

    I've heard claims it can be done, claims some have done it, and claims that it didn't work for them. This thread is interesting, some indications it should be possible, complaints that it didn't, and also an interesting work-around:
    "How do I text message multiple people at once?"
    http://discussions.apple.com/click.jspa?searchID=-1&messageID=4822260
    You can ask Apple for iPhone changes via this link:
    http://www.apple.com/feedback/iphone.html
    Though if you're requesting hardware changes for iPhone v2 you may want to wait a week (or a month?)...they're probably going to be inundated right now by requests for software changes to the current iPhone.
    (If this has answered your question, please mark your original post as answered)

  • Is there a way to open CSV files with more than 255 columns?

    I have a CSV file with more than 255 columns of data.  It's a fairly standard export of social media data that shows volume of posts by day for the past year, from which I can analyze the data and publish customized charts. Very easy in Excel but I'm hitting the Numbers limit of 255 columns per table. Is there a way to work around the limitation? Perhaps splitting the CSV in two? The data shows up in the CSV file when I open via TextEdit, so it's there. Just can't access it in Numbers. And it's not very usable/useful for me in TextEdit.
    Regards,
    Tim

    You might be better off with Excel. Even if you could find a way to easily split the CSV file into two tables, it would be two tables when you want only one.  You said you want to make charts from this data.  While a series on a chart can be constructed from data in two different tables, to do so takes a few extra steps for each series on the chart.
    For a test to see if you want to proceed, make two small tables with data spanning the tables and make a chart from that data.  Make the chart the normal way using the data in the first table then repeat the following steps for each series
    Select the series in the chart
    Go to Format sidebar
    Click in the "Value" box
    Add a comma then select the data for this series from the second chart
    Press Return
    If there is an easier way to do this, maybe someone else will chime in with that info.

Maybe you are looking for