No Preview in the Monitor panel

Hello all,
when I start playing the images, there is no preview available in the Monitor panel (white screen). Only stopped sequenzes were shown and the sound is playing. This problem occurs independently from the used files. When starting Pre there is a failure shown:Problems with the Intel Graphics.But the driver is updated to the latest version. Furthermore it is not possible to change the setting from the Graphic Card as described in the Pre Help.
Select Edit > Preferences > General.
Deselect Enable GPU Playback and in the Playback Preferences dialog, click OK to confirm.
This menu is not available!
Thanks in advance for your help and best regards,

What model of camcorder is your video coming from and what format it is?
When you started your project, which project settings did you select? If you selected the right project settings for your video, you will NOT see red lines above your clips when you add them to your timeline. Is this the case in your project?
Have you ensured you have the latest version of Quicktime, per the program's requirements? Have you gone to the nVidia or ATI site and ensured you have the latest drivers for your graphics card?

Similar Messages

I have tried to view videos created in premiere elements 10 and I get the following message: "this file type is not supported, or the required codec is not installed. When it opens there is a red screen in the monitor panel with Korean writing which als

I have tried to view videos created in premiere elements 10 and I get the following message: "this file type is not supported, or the required codec is not installed. When it opens there is a red screen in the monitor panel with Korean writing which also appears in the place of each clip in the video. I tried uninstalling and reinstalling premiere elements 10, but that did not have any effect on the video. Do you have any suggestions? I researched codec, but do not understand them at all.

gloucester
In case you did not find it, the following is a copy/paste of the Announcement on Premiere Elements 19/NVIDIA GeForce
that appears at the top of this forum.
Premiere Elements 10 NVIDIA Video Card Driver Roll Back
If you are a Premiere Elements 10 user whose Windows computer uses a NVIDIA GeForce video card and you are experiencing
Premiere Elements 10 display and/or unexplained program behavior, then your first line of troubleshooting needs to be rolling
back the video card driver version instead of assuring that it is up to date.
Since October 2013 to the present, there have been a growing number of reports about display and unexplained workflow
glitches specific to the Premiere Elements 10 user whose Windows computer has a NVIDIA GeForce video card. If this applies
to you, then the “user to user” remedy is to roll back the NVIDIA GeForce video card driver as far as is necessary to get rid of
the problems. The typical driver roll back has gone back as far as March – July 2013 in order to get a working Premiere
Elements 10. Neither NVIDIA nor Adobe has taken any corrective action in this regard to date, and none is expected moving forward.
Since October 2013, the following thread has tried to keep up with the Premiere Elements 10 NVIDIA reports
http://forums.adobe.com/thread/1317675
Older NVIDIA GeForce drivers can be found
http://www.nvidia.com/Download/Find.aspx?lang=en-us
A February 2014 overview of the situation as well as how to use the older NVIDIA GeForce drivers for the driver roll back can be found
http://atr935.blogspot.com/2014/02/pe10-nvidia-video-card-roll-back.html
ATR

Why would my video clips be running too fast when played on the monitor panel?

I posted my problem earlier today, but re-reading it maybe I didn't explain myself well enough.
My main question is: "why would my video clips be running too fast when played on the monitor panel ?". This is occuring after I have selected my media from the Tasks Panel and placed them in correct order in the Timeline/Sceneline. I knew something was wrong when I could see that the clips were not indicating their right length when viewed in the (expanded) timeline. They were compressed into just a few seconds, whereas the clips should have been at least 5 minutes. I ran the clips in the monitor and sure enough they ran too fast, with a lot of jerking movements.
The 3 video clips I am trying to make into a HD PAL video were taken with my Nokia N8 mobile video camera. These are in mp4 format. Can this present a problem ? Note that when I play these individual HD clips on my computer in (Windows Media Player) they run fine.
After I placed the clips in my Project Panel (or before in the Organize Workspace), I have perforned no change or manipulation of the clips. They are in their original state.
Just too confirm that the clips did seem to be compressed, I burnt a DVD, the resultant video ran in a matter of seconds.
Help would be greatly appreciated.

Yes, that is what the problem was.
Although the video camera on my Nokia N8, mobile was capturing at 25fps,
for some reason once transfered over to PrE9 (via file transfer), the clip was interpreted as 500fps. Once in Interpret Footage I was able to change the fps to 25.
Thanks for the help.

I'm stuck in the monitor panel.

I want to add to my movie, but cant get out of the monitor panel. How do I get back to the time line so I can add more to the movie?

Hi, in answer to your questions
. We have elements 7 and are using a HP laptop. I shut down the computer and then realised that I had not shut down Elements first. I canceled shutdown and went back and shut the programme. When I later returned to elements , I found that I could not get out of the monitor panel.
Date: Fri, 1 Nov 2013 14:38:17 -0700
From: [email protected]
To: [email protected]
Subject: I'm stuck in the monitor panel.
Re: I'm stuck in the monitor panel. created by A.T. Romano in Premiere Elements - View the full discussion
valleysend
What version of Premiere Elements are you using and on what computer operating system is it running?
Are you working with one monitor system? Have you been moving workspace panels around?
What workspace are you in
Premiere Elements 12....Quick, Expert, Quided Quick, Quided Expert
Premiere Elements 11...Quick or Expert
Premiere Elements earlier than 11, Timeline or Sceneline
What were you doing last before you realized you could not import additional source media?
Let us start here and then decide what next.
Thanks.
ATr
Please note that the Adobe Forums do not accept email attachments. If you want to embed a screen image in your message please visit the thread in the forum to embed the image at http://forums.adobe.com/message/5807974#5807974
Replies to this message go to everyone subscribed to this thread, not directly to the person who posted the message. To post a reply, either reply to this email or visit the message page: http://forums.adobe.com/message/5807974#5807974
To unsubscribe from this thread, please visit the message page at http://forums.adobe.com/message/5807974#5807974. In the Actions box on the right, click the Stop Email Notifications link.
Start a new discussion in Premiere Elements at Adobe Community
For more information about maintaining your forum email notifications please go to http://forums.adobe.com/message/2936746#2936746.

PE10: Is there a way of dragging the anchor point within the monitor panel?

I need to drag the anchor point to the far right upper corner to make that point the pivot point for photos. Tried every combination I could think of, but can’t find a way.

I am used to Premiere Pro 5.5 that has the capability.
I have 40 some odd photos to do this with. I tried to automate the process by creating a preset. With premiere elements it seems to take longer. I guess I just have to fool around with what's available.
I am using premiere elements 10 upgraded from premiere elements 9, which had the color matte function which I can't find it elements 10. Can you tell me where that function my lay?

.mts file video won't play in Elements 10 Monitor Panel

Hi All
I am having trouble with .mts files. I have Premier Elements 10 on Win7 pc, and I have just, for the first time, opened .mts video files which were taken on my Lumix FZ150. When I drag the scenes onto the timeline then try to preview them I can hear the audio but the video in the Monitor Panel doesn't move, it doesn't play.
Is there something I am doing wrong?

jgjgjfjf
What computer operating system is your Premiere Elements 10 running on? And, does your computer use a NVIDIA GeForce video card/graphics card?
IMPORTANT. Please read the Announcement at the top of this forum regarding the Premiere Elements 10 NVIDIA GeForce issue. That Announcement describes the problem and gives detailed information on how to deal with the situation.
Do you have problems getting a video display in the Edit area monitor for still and videos from other sources?
Also of importance in directing the troubleshooting are the properties of the Panasonic Lumix FZ150 video file that you are importing and the project preset that you are selecting to match the properties of that video. From what I have read of your camera, you could have MPEG-4, AVCHD, or MotionJPEG video compression. But, with that .mts file extension, that would suggest that your camera is set to record AVCHD. Is that correct? Are you sure of the file extension and video compression for the file?
The answers to all of the above will point us to the solution to your issue.
We will be watching for your results.
Thank you.
ATR

Monitor Panel question

First timer here, so bear with me. I have imported my files, but the monitor panel right side is zoomed in. I have a feeling I just missed a setting somewhere. Can anyone tell me what I did wrong and how do I fix it?

Looks like I may have just selected the wrong video type when I first created the project. Is there any way to change that,
or do I have to start the project over again?

Capture monitor panel issue

Everything worked fine in capture mode from a camera.When i change the 4850 ati with a new GTX 470 n vidia,the monitor panel in capture mode, looks like the black level has increased,or something like that.. Actually there is no basic problem the clip is captured correct.Does anyone knows about it?The same issue happens also in cs4.ASUS P6T, I7,12GRAM, VISTA 64 NVIDIA DRIVERS 260.99.

Thanks a lot for your reply.I did but nothing change.During capture if i click capture settings i can see the real black in monitor.Why the source and the program monitors are correct and this happens only in capture mode?

Where is the parameter panel on the embedded Crystal Report preview in Visu

Where is the parameter panel on the embedded Crystal Report preview in Visual Studio?
I found a tweet on google about this.. but the link is invalid.. and I could not find the article on SDN.
KB #1486469 - Where is the parameter panel on the embedded Crystal Report preview in Visual Studio? http://tinyurl.com/22thlcg
How do I the show parameter dialog in either WPF or Winforms viewer of Visual Studio 2010.
Parameters are not even visible in the Parameters Side panel. It is empty too..
I see two classes ParameterPrompting and ParameterPrompt both, on initialization throws exception.. even to manually invoke them...
Is it permanently removed?

Hello,
Seems like a reported Bug.
Please check:
Re: CRVS2010 - Hide Group Tree and Parameter Panel
A possible woraround but you need to change as per your need:
CRVS 2010 BETA - WPF Viewer - How to hide SidePanel?
Hope it helps.
Thanks.

Is it possible to preview images in the files panel?

sorry in advance for what probably is a dumb question with a
simple solution.
i realize i can preview images in the assets panel-- but is
it possible to preview image files while in the files panel
instead?
i have a lot of images organized within folders in the files
panel-- so it's easier there to locate and visulalize an image--
than scrolling down the long list in the assets panel.
thanks.

Hello,
I don't believe there is a way to view images in the files
panel.
However, there's a quick way to see them if you're using
Windows.
Select your image folder in the Files Panel.
Right click and choose "Explore".
It opens a window where you can see all the images in that
folder.
It's much faster than scrolling through the assets, clicking
the file names
and reading the paths to know where they are.
This is very handy whether you have image folders in
different directories
(for organization and cleaner img src paths in the pages
within the
directory) or if you just dump them all in a folder in the
root.
On my wishlist: Hover over the image name in the files panel
and a small
box, like a tool tip, displays the image.
Maybe someday.
Take care,
Tim
"dexter manika" <[email protected]> wrote in
message
news:go4to8$k1m$[email protected]..
> sorry in advance for what probably is a dumb question
with a simple
> solution.
>
> i realize i can view images in the assets panel-- but is
it possible to
> view
> image files while in the files panel instead?
>
> i have a lot of images organized within folders in the
files panel-- so
> it's
> easier there to locate and visulalize an image-- than
scrolling down the
> long
> list in the assets panel.
>
> thanks.
>

I have Macbook Pro and Adobe CC. 3D won't work.. I can open the 3D panel options but clicking ok or even choosing preview brings up an error message [can't]

I have Macbook Pro and Adobe CC. 3D won't work.. I can open the 3D panel options but clicking ok or even choosing preview brings up an error message [can't]
My friend has exact same Mac and CC and he has the same problem. We both have up to date Yosemite and CC versions.
Any ideas?

Hi,
Could you please confirm the CC application you are using.
It would be great if you post a screenshot of the problem.
Regards,
Sumit Singh

I'm using a viewsonic 19" LCD monitor with a powermac 7100/66. The only resolution available in the monitor control panel is 640x480. The viewsonic gives me a message to use 1440x900. The mac specs state it's capable of 1152x870 @ 8 bit. Help!

I'm using a viewsonic 19" LCD monitor with a powermac 7100/66 running Mac OS 7.6.1. The only resolution available in the monitor control panel is 640x480. The viewsonic gives me a message to use 1440x900. The mac specs state it's capable of 1152x870 @ 8 bit. How can I get a higher resolution?

For unsupported resolutions, one may need to see if there are any software
solutions; maybe the minimum specs of the display are not met by an 8-bit
color specification of the video card in the computer.
Does the display support two kinds of connections, another one, plus VGA?
Could be the display needs some other support for it to work. Drivers?
VRAM? A different control panel and (third-party) software?
The limits may vary due to the VRAM on the card. With enough there, and
with a VGA connection (or supported converter to/from older Mac DB-15)
and the video graphics card with minimal supported specs will show that.
Been several years since I've run any PowerMac, & only used a variety of
Apple CRT color displays with them. Most times, they were very adequate.
A wider array of original choices appeared in the Displays control panel...
So I suspect the lack of video support in the graphics card or VRAM, to be
a player in this resolution limit you see in the control panel. A later CPU/GPU
and better hardware, later Mac OS, offered greater support for newer driver
along with better results.
There may not be a workable upgrade to a different graphic video card for
that old a vintage computer; or if there was one, to locate that now may be
a next-to-impossible mission. Was there any hints in the web site for older
Macs, the LowEndMac site, or others? Some are no longer current sites.
In any event...
Good luck & happy computing!

How to synchronize presentation on the front panel to the start of a 75Hz monitor's retrace cycle?

How to synchronize front panel presentation with the start of a retrace cycle of a 75Hz Monitor, so when a bitmap is presented 100ms, its duration is indeed 100ms on the monitor?

Hi,
In the old days (late 90's), we used in port and out port to wait for
vertical retraces (or even horizontal retraces).
I searched the web (vertical retrace), and there seem to be lots of
infromation and tools, like
http://www.compuphase.com/vretrace.htm
It uses a simple routine:
mov dx, 3dah ; VGA input status register
vretrace_loop:
in al, dx
test al, 8 ; bit 3 set?
jz vretrace_loop ; no, continue waiting
But to get it working, you need a VxD. Good news is you can download it.
The also suggest you use WaitForVerticalBlank(), but dx could be hard to get
working under LabVIEW.
Please let us know how (and if) you got it working with LabVIEW!
Regards,
Wiebe.
"Vinci HK" wrote in message
news:[email protected]...
> Hi Robert,
> I am so excited to have received a response! Sorry that I didn't reply
> earlier as I have been out of town. You are understanding the problem,
> so good!
>
> I just want to know the exact duration a stimuli in the front panel is
> presented. I can make it to last for 13 frames, but the problem is to
> ask LabView to synchronize with the start of a frame.
>
> The crucial thing is that I want a trial of presenting 700ms blank
> screen + 1300ms bitmap will add up to 2000ms on the front panel. And
> in the next 2000ms, a different bitmap will be used for the 1300ms.
> The start of a trial is initiated by a pulse from the parallel port. I
> need the 2000ms on the front panel to be really 2000ms+/-5ms.
>
> My worry is that even if I buy the external clock and the RealTime
> system of LabView, I won't be able to get the front panel to
> synchronise with the refresh cycle of the monitor, so that the trial
> length as it appears on the front panel is 2000ms +/- 5ms.
>
> What do u think?
>
> I am using LabView for my fMRI experiment, and I wonder if you know
> anyone from the fMRI community who are using LabView for stimulus
> presentation and synchronization with MRI data acquisition?
>
> Thanks,
> Vinci

How do I monitor parameters from a SubVI on the front panel of the main VI?

Good day. I have a LabView program that I am modifiying (actually it is a National Instruments demo program called Simple PID Demo). On the Front Panel of the main VI, I need to monitor several parameters that are on a SubVI. How do I do this?
Thank you very much for your time and help.
Michael

Hi Michael,
Global Variables should solve your problem.
Looks like you have to pass values from Sub VI that will execute continously inside a main vi.
Look at attached VI
Hope you can implement this type of logic in your program.
regards
Dev
Attachments:
Main_1.llb ‏53 KB

How to let Final Cut "ignore" other monitor and have preview on the largest

How to let Final Cut "ignore" the other monitor" and have preview on the largest monitor?
I have a setup with a MB Pro and an external Eizo 27" calibrated screen.
Now I am using the 27" as the main screen with Final Cut with its panes and windows on it and the MBPro as preview (Command F12). I would like to see the preview on the large 27" when I hit Command F12 and not on the laptop sometimes. Any way to do this?
When I do the "mirror" screen setup the resolution drops down on the Eizo 27" so that does not seem to be a good option.
Any solutions?

Try:
View>Video Playback>Digital Cinema Desktop-Main

No Preview in the Monitor panel

Similar Messages

Maybe you are looking for