NO PRINTERS FOUND - setting up no internet access printing with ipad 2

I have just purchased a:
Ipad 2
AirPort Express Base Station with 802.11n
HP LaserJet P1102w Printer ( An Airport supported printer suggested by apple - http://support.apple.com/kb/ht4356 )
Heres what i want:
I want to be able to put this printer in my car and print from my ipad to my printer via wifi or bluetooth (whichever will work)
Heres what i did and its not working:
unboxed everything
activated my ipad
got printer to print wirelessly from my windows laptop so i know it works!
configured a new wifi network on the airport express base station
I did not setup airtunes when asked too during setup - Not sure if this makes a difference.
tried printing to printer from ipad and it says " no airport printers found"
Please help?
I also went into the manual setting of the airport express base station and under printers there is no printers to select there to edit!
Next I physically connected the printer to the base station and it still will not print!
Any help is much appreciated - thanks!

Marc
The DSL needs a route back to the 192.168.10.x network. So using IOS terminology (although the DSL will have different syntax) -
ip route 192.168.10.0 255.255.255.0 192.168.2.2
if you cannot add a route to the DSL then the other option is to NAT all 192.168.10.x IPs to 192.168.2.2 so that DSL knows where to send teh return traffic eg.
int eth1/0
ip nat inside
int fa0/0
ip nat outside
access-list 101 permit ip 192.168.10.0 0.0.0.255 any
ip nat inside source list 101 interface fa0/0 overload
Jon

Similar Messages

Can I use my iPhone to have internet access on the iPad?

Can I use my iPhone to have internet access on the iPad?

Yes, but you have to have your phone set up for tethering. Depending on your carrier that might require a special plan.

How can I set up a guest access point with a Time Capsule and an Airport Extreme? I am using a Telus router with the Time Capsule used as a wireless access point (bridge mode). I don't want the guest access point to have access to my network.

How can I set up a guest access point with a Time Capsule and an Airport Extreme? I am using a Telus router with the Time Capsule used as a wireless access point (bridge mode). I don't want the guest access point to have access to my network.

The Guest Network function of the Time Capsule and AirPort Extreme cannot be enabled when the device is in Bridge Mode. Unfortunately, with another router...the Telus...upstream on your network, Bridge Mode is indicated as the correct setting for all other routers on the network.
If you can replace the Telus gateway with a simple modem (that performs no routing functions), you should be able to configure either the Time Capsule or the AirPort Extreme....whichever is connected to the modem....to provide a Guest Network.

How do I set up a booklet to print with my Konica Minolta?

how do I set up a booklet to print with my Konica Minolta?

Is it a BizHub? If so, use the booklet printing from the Koncia driver.
If it's like the one I have, click the Printer button at the bottom of InDesign's print dialog, then choose Layout/Finish from the drop down menu, and booklet from there.
One thing to note: with this method, leave your paper size the same as one page of your document.

Can i set up a cannon s450 printer with my mac

Is it possible to set up an s450 cannon printer with my mac? If so, how?

No. It only works with very, very old versions of the Mac OS (7.x-8.x).
Clinton

Set up an internet fax service with an iBook G4 for $12

NOTE: There are plenty of online resources for configuring the elements discussed below. I don't want to write a book so I'll let you look these up for whatever providers and devices you ultimately use.
For what it is worth, here is my recent experience with my wife's trusty old iBookG4 which keeps on giving. For years now it has been a living room music hub, but once a year or so it gets used to send out a fax as all the newer machines lack the modem.
Recently I wanted to set up a permanent fax line, but expecting it to not get used much didn't want to invest much. I now have a permenant fax line with internet access for $12.
The $12 is just the annual cost of a DID number from a voip provider as I already had the necessary bits in use for other purposes, i.e.:
an iBookG4 (or other older model that can run OS X and has an internal fax modem)
a Linksys PAP2T ATA device (this is a fax compatible device which converts voip digital signals to analog for older phone systems. The PAP2T has two telephone line ports.)
STEP 1
Get yourself a phone number from a solid voip provider (one you can configue online). Set the audio codec to be only whatever your ATA device expects for fax compatibility. For the PAP2T this is G.711. I used voip.ms for the provider, there are others. The business line option is $0.99/month plus whatever time your faxes take -- which I don't expect to be much at $.01/minute. (You may notice that the voip rates are insanely low, this is because services like AT&T and even MagicJack make their money by simplyfing the process which can look intimidating, but in truth almost all default settings will work.) Check online for your service providers required settings. Most will have device configuration samples.
The essence here is to set up a voip service through an ATA to your iBook. (You don't have to do a voip line, you can go ahead and pay the regular phone company dedicated line rate if you wish. This is the saving money part, not internet functionality.)
STEP 2
Get Dropbox onto your iBook and your iPhone, iPad or whatever. Install a VNC app onto your iPhone so you can use the Apple Remote Desktop. The free Mocha VNC Lite app worked fine for me.
STEP 3
Go to Print&Fax preferences and click on the + button to create a fax printer as you did in the old days, but this time go Receive Options, turn on Receive faxes on this computer and set Answer to 1 so it responds immediately and Save to: to a Dropbox folder of your choice. (Since my iBook is always plugged in I disabled computer sleep as well in Energy Saver as it also needs to be readily availble to serve music.)
STEP 4
Go to Sharing preferences and enable Remore Management. For security I set access to a single dedicated user. Your needs may vary.
STEP 5
Make sure your Firewall will pass through VNC or typically port 5900. You have to see what your system requires to enable VNC and Apple Remote Desktop. Also, go into Network preferences, Advanced, and set a DHCP with manual address to ensure your firewall pass through always hits the right machine.
STEP 6 - Testing
- Go online to your voip provider and ensure your DID has registered.
- Create .txt or PDF on whatever machine and copy it to your Dropbox folder.
- Go to the HP fax test page and follow their instructions to send them a fax and have an automatic fax back.
- Head off to Starbucks or local wifi spot (you might want to use Hotspot sheild or other encryption). Call up VNC, go into Preview or whatever app and print to fax (IMPORTANT: There is a bug in OS X, since 10.4 I believe, requiring you to turn off the "Receive faxes on this computer" in order to send a fax. Turn it off, send, then go back and turn it on)
- Leave your VNC app and wait a bit. Soon Dropbox should notify you a file has been placed in your folder.
There you go Receive and Send faxes on your iPhone wherever you can get wifi. Or, as the civilized world does, send a PDF and let the less advanced send you a fax if they have to.

Use the instructions in this article to create a new network location; each location has its own set of options and doesn't affect the other locations.
(10942)

HT4199 why can't I get internet access on my ipad mini when attached to itialian router whilst on holiday

I live in France but I am in Sicily on holiday for a month's holiday. My ipad is showing that I am connected to a router in Sicily but I still can't get internet access and on facebook it is marked 'network error'

Hello there, sheilafromfra.
The following Knowledge Base offers up some great steps for troubleshooting the Wi-Fi issue on your iPad:
iOS: Troubleshooting Wi-Fi networks and connections
http://support.apple.com/kb/ts1398
Thanks for reaching out to Apple Support Communities.
Cheers,
Pedro.

How to set up hp 7515 to print from ipad

I can't print from mynipad to hp7515 printer. The air print doesn't have printer listed although it was installed and did work for a while?

Hey Gwilliams! So AirPrint did work for you previously? I would check out the AirPrint Assistant and see if that helps your get it working again. You didnt state if you were getting an error message but you could also check out this document: 'The Printer is not Found,' 'No Printers Found,' or 'Printer is Offline' Message Displays on the iPa...
Its directed towards customers who receive that specific error message but may also be helpful for you. Let me know if it fixes your issue! Good luck
-------------How do I give Kudos? | How do I mark a post as Solved? --------------------------------------------------------

Is there a setting to make a PDF print with no background and black text?

I made a nice booklet that has colorful blocks in the background and sometimes white text and sometimes black text. We are not going to print it, it is just going to be a PDF on our website. Can I set it up so that it always prints without the backgrounds and makes all the text black?
I just don't want people to have to print huge fields of colr if they end up printing this out on a little ink jet with expensive and finicky cartridges...
BT

There are is no as such specified setting for customer or reader printer, because it depends on the printer setting of customer. However, you can mentioned that, if any one want to print book as black text, follow this setting http://helpx.adobe.com/acrobat/kb/print-black-white-acrobat-reader.html

How do i set up a wireless access point with ny time capsule

I am using a new Airport Extreme and want to utilize my older TC to create a wireless access point or maybe an aditional router using the same newtwork. What are the steps to set this up?
Thanks
Alamo

You will first need to perform a Factory Default Reset on the Time Capsule.
Resetting an AirPort Base Station or Time Capsule FAQ
Then, temporarily locate it in close proximity (same room or nearby) to the AirPort Extreme.
Open Macintosh HD > Applications > Utilities > AirPort Utility
Click the tab in the upper left hand corner of the AirPort Utility window that reads Other AirPort Base Stations (1), then click the Time Capsule
AirPort Utility will take a moment or two to analyze your network, then announce that the TC will be configured to extend your wireless network.
Enter a name for the TC (you can use the same device name that you used before if you wish) and click Next.
AirPort Utility will take a another minute or two to configure the TC and then tell you that the setup is complete. Click Done
At this point, power down the TC and move it to a location that is approximately half the distance from the AirPort Extreme and the area that needs more wireless coverage.....to give the TC a good strong signal to "extend"
Power up the TC and wait for the green light and then you are all set.

Lost internet access & printer settings after switched off airport extreme

Hi,
when I switched off my airport extreme I lost internet & printer settings. All other settings are OK. What`s my problem or what do I wrong?

please go to windows section and you need to provide more specific information to your problem.

How do I set up a d7400 to print from ipad.

I am trying to get my iPad to print using the HP home&biz software on my D7400 printer. The web pages say it is compatible, but offer no instructions on setting it up (at least that I can find). Any help would be greatly appreciated. I will also be setting up a C309g once this one works, I'm hoping they are similar! Thanks
This question was solved.
View Solution.

Hi,
You may find the steps to get and use the App below:
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c02775166&cc=us&dlc=en&lc=en&product=3795314&tmp...
Please let me know of any clarification you may need,
Shlomi
Say thanks by clicking the Kudos thumb up in the post.
If my post resolve your problem please mark it as an Accepted Solution

HT3500 Setting up wireless on a printer with preloaded drivers in 10.9.1

I'm trying to connect an HP Deskjet 3050 J610 printer to my wireless network. It's an older model so the CD that came with it is not compatible with OS X 10.9.1, but the printer driver is already loaded in the operating system. So I'm able to print using the USB cable but when I try to connect with my Belkin router via WPS the printer won't connect because it has a pre-assigned SSID. I'm unable to find any configuration program on the computer that would allow me to change the SSID on the printer manually. So far HP has been no help so I'm hoping the Apple community might have a few more answers.

Removing the SSID from the global config first, causes the SSID to be removed from the radio interface. If you remove the SSID this way the AP WILL NOT crash.

How do i set up my wireless lexmark printer with my imac

how

You can download the drivers at www.Lexmark.com or through Apple's software update. Or you can check this link for steps on how to connect your Lexmark printer to your wireless network: http://support.lexmark.com:80/lexmark/index?page=content&locale=EN&productCode=& segment=SUPPORT&viewlocale=en_US&searchid=1320934367324&actp=search&userlocale=E N_US&id=HO3531

Motorola V525 UK Vodafone Internet Access Point

Hi guys
I have a Midlet that makes an HttpConnection to a servlet to get some String data. It works perfectly well through the emulators, but not on my phone. Having read the forums I can see that this is probably because I have a WAP access point for my GPRS connection on the mobile. I rang Vodafone to ask them about how to set up an Internet access point via TCP/IP, but they were next to useless. So anyone know how to set up an Internet APN for Vodafone on a Motorola V525 ?!?
Thanks
K
ps. If you know another way to get data from a server that doesn't involve an HttpConnection, that would be great also.

Hi Killuminati.
The settings you need are for the Vodafone Internet APN, as below:
Access Point (APN) address : internet
Username : web
Password: web
(note that these are all case sensitive)
You may also need to explicitly set the DNS server (I can't remember if you actually need to do this or not):
DNS Server: 212.183.137.012
Ok, now that may be enough for it to work. If you are still having problems however, then you need to phone Vodafone, as we've found that some people need to get access to the Internet access point explictly turned on for their account.
This can be tricky, and has taken us from between 5 mins, and 2 days to get sorted out, depending on whether the person on the end of the phone knows what they're talking about or not!
Explain to them (slowly!) that you need to have access to the Internet GPRS Access point turned on for your phone (explain if necessary that you already have access to the WAP Access point but that is different.
Once you find someone that actually understands what you're talking about, it should then be a 5 minute job for them to activate it for your account. You then turn your phone off & back on, and you should then be up & running (after ensuring your phone is set up to use the Internet Access Point instead of the WAP one of course).
Hope that's of help.
Cheers,
Neal.

NO PRINTERS FOUND - setting up no internet access printing with ipad 2

Similar Messages

Maybe you are looking for