No ring on analog phone

Hi I have a router 1750 with an analog phone connected through an FXS port on the router. The voice works but when the extension number is dialed the phone does not ring. What can the problem be?
Regards.

What is your dial-peer configuration ?
If yo want to see how the router rings the phone, check "debug vpm signal" with "term mon".
Hope this helps, please rate post if it does!

Similar Messages

Analog phone with ring light

We have analog phones in certain applications that use a neon light instead of a ring tone. It requires 90v to activate the neon light. We have VG224 analog gateways which appear to not be able to push 90v. Does anyone have a solution or is there another Cisco gateway that will support analog phones that use a neon light instead of a ring?

BlackBerrys have a flashing red LED indicator light for new messages. It's hard to miss. And with the sleeve cases, there is a gap for keeping this notification light visible, even when holstered.

SPA9000 + SPA492 + analogic phone: Cancel Request doesn't work

Hi all, I'm build up a LVS in the following configuration: SPA9000 + SPA942 + analogic phone on FXS1; PBX connected to LAN with WAN interface and IP phones on the same LAN at all; "Force Media Proxy" parameter = "yes"; "Line 1" in trunk with an ITSP; no NAT parameter changed from default; WAG54GP2 on ADSL as Internet gateway in standard configuration. All seems running fine, except for one small but really fundamental function: I start an outbound call from SPA942 or analogic phone, the addressed phone rings and if I hung up before the call is accepted, the phone on the other side keeps the ringing up. In my opinion, it seems like a failed "Cancel" request. If I try to do the same with the analogic phone conected to WAG54GP2 all runs well, so I can exclude a signalling problem of the ITSP. Thanks in advance for your help.

Several things to try -
1) Set NAT mapping and NAT Keep Alive to yes on the SPA9000 line connected to the ITSP.
2) Setup port forwarding on the WAG54GP2 to forward port 5060 to the IP address of your SPA9000.
3) Replace the WAG54GP2 with a standard modem and connect the SPA9000 directly to it.

PAP-2T, make incoming calls ring in both phones/Lines?

I have a PAP-2T. On this device I have connected two different phones, one connected to Line 1 and the other to Line 2. I have one SIP account with my provider. My provider has configured my account so that I can make two concurrent outgoing calls. My Lines are configured as the following;
Line 1:
Proxy: xxxx.sipserver.xxxx.xx
Outbound Proxy: <blank>
Register: Yes
Register Expires: 3600
Use Outbound Proxy: No
Use OB Proxy In Dialog: No
Make Call Without Reg: No
Ans Call Without Reg: No
Line 2:
Proxy: <blank>
Outbound Proxy: xxxx.sipserver.xxxx.xx
Register: No
Register Expires: 3600
Use Outbound Proxy: Yes
Use OB Proxy In Dialog: Yes
Make Call Without Reg: Yes
Ans Call Without Reg: No
Now, when I receive an incoming call, the phone connected to Line 1 rings. If I configure Line 2 like this,, Ans Call Without Reg: Yes,, the phone on Line 2 rings but not the one on Line 1.
My question is,, can I make both phones ring when I receive an incoming call?
If so, how do I configure the ATA to make that happen?

Cat2k1 what kind of probs do you hve with your phones ?
- assume it's a DECT phone, try to change the ring voltage to 75V and ring waveform to trapezoid - this works better with problematic DECT phones
- assume you're having an old analog phones, make sure the PAP2T's Line1 socket is only connected via 2wire interconnect cable (4wire cable on Line1 plus certain analog phones is a trouble-maker)
- assume you use multiple analog phones on one line, you may consider increase the FXS power from 3 to let's say 5
- assume you're having an old analog phone, it's ability to ring (if all the SIP comm works OK) is also affected by the FXS port impedance which must (shall) fit the phone's one.
====
On the other hand, shall you have problems with SIP communication between PAP2T an SIP operator, you shall enable NAT traversal and NAT keeplalive for the first on PAP2T settings
Message Edited by Scorpio-cz on 12-24-2008 10:50 PM

Setup Hotline Analog Phone with SCCP

Anyone out there can help me out how to setup a hotline in CUCM 8.6?
I've followed this procedure below, but I'm still getting an error message when I lift the handset such as "your dial cannot be completed...".
http://www.cisco.com/en/US/products/sw/voicesw/ps556/products_configuration_example09186a0080232b9f.shtml
Just in a nutshell, here is what I've done:
Extension: 1111 PLAR Analog SCCP Phone with: CSS_Hotdial and PT_Allowed (line settings)
TP: blank, PT_Hotdial and CSS_Hotdial, and called PTM: 2222
Extension: 2222 CSS_Allowed, and PT_Allowed - no changes on this extension...
Added the PT_Allowed into CSS_Hotdial. The order is: PT_Hotdial/PT_Allowed
Both lines are on the same VG204-vg20x-ipvoice-mz.124-22.T5.bin. When I selected hotline feature it says is supported Analog Phone SCCP, but I did not see the VG. It looks like is not supported hotline on VGs. Can someone confirm that?
Am I missing something? Do I need to enable something under Service/Enterprise parameters?
Thank you!

Chris, thanks for your prompt help.
I thought the TP needs a CSS with access to the 1111 DN, not to the 2222. Because when someone lifts the handset on phone 1111 this phone should invoke the TP which translate and ring to the 2222 phone. Thus, I put this CSS_Hotdial on phone 1111 under line.
And my TP looks like this: PT_Hotdial and CSS_Hotdial, and called party transformation mask 2222
The CSS_Hotdial has only access to one PT_Hotdial.
Also the two phones 1111 and 2222 are on the same partition PT_Allowed, but they are on different CSS.
Anyway I also tried what you said but did not work. Are you sure this hotline works on VG204? I think it is not working because this feature is not supported on VG204 nor in any VG model.
If you are sure it should work. Could you please elaborate more this solution with PT/CSS/TP?
Once again thanks

Vg224 don't auto disconnect with analog phone

Dear all ,
why vg224 don't auto disconnect with analog phone? is the busy frequency dismatch between vg224 and analog phone?
can you have any suggest to me ?
thks.

HI rrjoas45,
thks your answer, I try to add a command with supervisory . but I discovery it isn't effective . the port status follow:
sh voice port 2/0
Foreign Exchange Station 2/0 Slot is 2, Port is 0
Type of VoicePort is FXS
Operation State is DORMANT
Administrative State is UP
The Last Interface Down Failure Cause is Administrative Shutdown
Description is not set
Noise Regeneration is enabled
Non Linear Processing is enabled
Non Linear Mute is disabled
Non Linear Threshold is -21 dB
Music On Hold Threshold is Set to -38 dBm
In Gain is Set to 0 dB
Out Attenuation is Set to 0 dB
Echo Cancellation is enabled
Echo Cancellation NLP mute is disabled
Echo Cancellation NLP threshold is -21 dB
Echo Cancel Coverage is set to 64 ms
Echo Cancel worst case ERL is set to 6 dB
Playout-delay Mode is set to adaptive
Playout-delay Nominal is set to 60 ms
Playout-delay Maximum is set to 250 ms
Playout-delay Minimum mode is set to default, value 40 ms
Playout-delay Fax is set to 300 ms
Connection Mode is normal
Connection Number is not set
Initial Time Out is set to 10 s
Interdigit Time Out is set to 10 s
Call Disconnect Time Out is set to 60 s
Supervisory Disconnect Time Out is set to 750 ms
Ringing Time Out is set to 180 s
Wait Release Time Out is set to 30 s
Companding Type is u-law
Region Tone is set for CN
Analog Info Follows:
Currently processing none
Maintenance Mode Set to None (not in mtc mode)
Number of signaling protocol errors are 0
Impedance is set to 600r Ohm
Analog interface A-D gain offset = -3.0 dB
Analog interface D-A gain offset = -3.0 dB
FXS idle voltage set to high
Ring DC offset set to 0 volt
Station name None, Station number None
Translation profile (Incoming):
Translation profile (Outgoing):
Voice card specific Info Follows:
Signal Type is loopStart
Ring Frequency is 25 Hz
Hook Status is On Hook
Ring Active Status is inactive
Ring Ground Status is inactive
Tip Ground Status is active
Digit Duration Timing is set to 100 ms
InterDigit Duration Timing is set to 100 ms
Hookflash-in Timing is set to max=1000 ms, min=150 ms
Hookflash-out Timing is set to 400 ms
No disconnect acknowledge
Ring Cadence is defined by CPTone Selection
Ring Cadence are [10 40] * 100 msec
Ringer Equivalence Number is set to 1
thks.

Hello i have a unusual problem,anyway my iphone 4 wont turn on and when someone calls they hear ringing,but my phone doesent ring,so i open cimcas now ring off. Screen is just black,because it's turned off..Please help me to solve this problem..Thanks

Hello i have a unusual problem,anyway my iphone 4 wont turn on and when someone calls they hear ringing,but my phone doesent ring.So i poen simcase and now ring off. Screen is just black,because it's turned off..Please help me to solve this problem..Thanks

As far as trying to power up your device, make sure it has a good charge and then hold the button on the top of the phone and the home button on the faceplate together until the apple appears on the screen.

My I phone is ringing as a phone. However, no sound could be heard when viewing youtube video no sound for the keyboard. Also when the vonage or the magic Jack is ringing it rings once and no more. I don't know how to solve this problem?

My IPHONE 4S Rings well as phone. However, I could not hear the sound from vedio or from ITUNES. Even the keyboard sounds are not clicking. The vonage and magic jack rings one and sometimes vibrate only.. what should I do to solve this probelm??

set the wake-on lan on the main computer
The laptop's too far away from the router to be connected by ethernet. It's all wifi.
No separate server app on the laptop, it's all samba
The files are on a windows laptop and a hard drive hooked up to the windows laptop. The windows share server is pants, so I'd need some sort of third party server running. Maybe you weren't suggesting to use Samba to connect to the windows share though?
I'm glad that you've all understood my ramblings and taken and interest, thanks The way I see it, I can't be the only netbook user these days looking for this kind of convenience, and I certainly won't be once chrome and moblin hit the market.
Last edited by saft (2010-03-18 20:38:08)

I have a iphone4s and an ipod 4th gen, they both share same itunes acc, the ipod has its own email but when people try to FT it also rings on my phone, how do i stop it ringing both devices

i have a iphone4s and an ipod 4th gen, they both share same itunes acc, the ipod has its own email but when people try to FT it also rings on my phone, how do i stop it ringing both devices

That's because you're using the same Apple ID on both devices. On your phone: Settings>FaceTime>You Can Be Reached at>Remove your Apple ID.

How do I change the number of rings on my phone?

how do I change the number of rings on my phone?

Call your provider and ask them to do it.
This is not controlled from the iphone.

H.323 endpoint to analog phone call problem

I have Tandberg H.323 endpoints registered in gatekeeper, Callmanager 4.2(1) and MGCP voice gateway to classic telephony. There is a problem, when I try to set up a call from H.323 endpoint to the analog phone through voice gateway. The call is set up but disconnets after about 3 seconds alerting signal. However you can have normal connection, when you answer the phone during theese three seconds of alerting. When it disconnects it says: 'Resource unavailable, unsecified'.
What can cause such problem?
Thanks in advance.

NO, I was using an Sx-20 as the H323 endpoint. I tried a different video confernece unit.The other confernce unit worked with out any issues. Sorry I wish I new what was wrong with the sx-20. What kind of h323 endpoint are you using?

Abandoned Call Rings on Agent Phone

Hello,
I have a strange situation reported by a supervisor that, abandoned call keep rings on agent phones and when one of the agents answers the call she hears busy tone.
To reproduce this issue, we made some test calls and hung up the call just before the call starts ringing on agent phone.
The same call started ringing on agent phone. It looks like abandone en-route.
Any way to avoid this behavior.
UCCX: 9.0.2.10000-71
CUCM-BE: 9.1.1
Thanks,
Sami

Do you have an On Exception Goto (ContactInactiveException) step in the script that jumps to an End step? If not, add it near the Accept step. Without this, the script will carry on running even if a caller hangs up. I'm not saying this is your problem but it might be a contributing factor.
The second question is in-line with Gergely: does the PSTN circuit have disconnect supervision? Is the gateway telling CUCM the call has ended when the outside caller hangs up? (e.g. SIP BYE, Q931 DISCONNECT, etc.) If not this might be the PSTN reorder being heard.
Please remember to rate helpful responses and identify helpful or correct answers.

Caller doesn't hear a ring back if the call is ringing on agent phone

Hi team,
can anybody help me? Here in Germany there are a lot of customers that don't understand why the caller doesn't hear a ring back when the call is ringing on agent phone for instance with UCCX 8. I read some discussions here for that issue but the only solution for that should be to change the MOH on CUCM. This is not a very good solution when the call in queue is set to hold he will hear the ring back tone in the queue as well :-(
Has anybody another solution for that issue???
All the discussion I've read was for IPCC version 4 or so. Is there another solution for this issue in version 8.x
In one discussion I found the following solution:
Yes, To resolve this issue,Set up a Send H225 User Info Message service parameter for Cisco CallManager service in CallManager. Perform the following steps:
In Cisco CallManager Administration, select Service > Service Parameter.
Select the correct server from the drop-down list.
Set the service to Cisco CallManager.
In the Send H225 User Info Message field, under the Cluster Wide Parameters (Device - H323) section, select H225 Info for Ring Back.
Reset the H.323 voice gateway.
After completing this procedure, the caller hears ring back when the agent phone is ringing.
Does it realy work?
Need you help!
Thanks in advance.
Tobias

Hi Tobais
you right one of the solutions is to change the MOH to the ring back one
however there are two types of MOH that you need to select
use MOH is the music to be played while the call on hold/ in queue
use Network MOH which is the oneyou need to change to the ring back MOH source file so when the call get transferred to an agent ring back MOH will be played
these options under the CTI ports in UCCX
also you can search the forum here and there are many discussions about this topic
HTH
if helpful Rate

Why are calls from my favorites not ringing when my phone is silenced at night?

Why are calls from my favorites not ringing when my phone is silenced at night?

You Might Have scheduled do not diturb... Turn Of Scheduled button in settings>do not disturb>scheduled..

MWI on analog phone using stutter dial on VG248

Someone is telling me that you can use stutter dial or some other method to light up an anolog phone Message waiting indicator using on a VG248. This is with an analog phone that has an Message light on it. Is this possible and if so is it possible using and ATA with Call Manager?

Hi Shane,
This does work with the VG248, we have used the "Stutter Dial Tone" on some analog phones and used the actual MWI Lamp on other analog phones with good success. Have a look;
Choosing Message Waiting Indicator Type
The VG248 supports several types of methods for sending MWI messages to analog phones. Because you might have different types of analog phones connected to the VG248, you can modify the MWI type on a per-port basis. So, if you have some analog phones that have MWI lamps on them, you can notify users of awaiting messages using the lamp. Or, you can choose to play a tone when users pick up their phones.
Keep in mind that the VG248 only sends this information to the phones if it is received from Cisco CallManager. If Cisco CallManager is not integrated with your voice mail system, it does not send this information to the VG248.
Step 1 From the main menu, choose Configure.
Step 2 Choose Telephony.
Step 3 Choose Port specific parameters.
Step 4 Use the arrow keys to select the port to configure and press Enter.
Step 5 Choose MWI type.
Step 6 Choose from the following options:
Lampilluminates lamp on phone
Caller IDuses caller ID mechanism to send MWI messages to the LCD screen on phone
Stutterplays tones when user picks up the phone
Lamp + stutterilluminates lamp and plays tone
Caller ID + stuttersends message to LCD screen and plays tone
Nonedoes not send MWI information
From this doc;
http://www.cisco.com/en/US/products/hw/gatecont/ps2250/products_configuration_guide_chapter09186a0080087de4.html#xtocid13
Hope this helps!
Rob
Please remember to rate helpful posts..........

No ring on analog phone

Similar Messages

Maybe you are looking for