No route after Interface change in VRF

Hi Everyone,
I have had a couple of strange incidents where changing a physical interface or ip address on an interface causes routing problems. We are running ASR9010 on IOS-XR 4.2.3
Case 1:
Changed a physical interface gi0/0/0/1.12 to BE21.12 on a vrf.
I lost static routes and had to remove and re-apply.
Case2:
Changed the IP address to a different network 172.17.254.126/27 to 172.27.254.126/27
ARP OK and ping from VRF or local device in other VRF OK, however host on connected interface cannot be pinged from across MPLS. Connected route is carried across MPLS OK. We will be trying to remove the entire interface and vrf config and re-apply.
EDIT: We re-applied config after removing and commiting. It is now working.
Any ideas or clues?
Cheers
Mike

Thanks,
The basic thing for case 2 is:
Customer --> VRF Gateway- Ping OK
RP/0/RSP0/CPU0:macq-syd-intel2-asr9010-01#ping vrf BACKUP-MANAGEMENT 172.27.254.99
Fri Feb 14 12:42:49.771 EST
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 172.27.254.99, timeout is 2 seconds:
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/2 ms
Server --> MPLS --> VRF Gateway - Ping OK
>  ping routing-instance BACKUP_SERVERS 172.27.254.126
PING 172.27.254.126 (172.27.254.126): 56 data bytes
64 bytes from 172.27.254.126: icmp_seq=0 ttl=255 time=1.126 ms
64 bytes from 172.27.254.126: icmp_seq=1 ttl=255 time=1.029 ms
64 bytes from 172.27.254.126: icmp_seq=2 ttl=255 time=1.097 ms
64 bytes from 172.27.254.126: icmp_seq=3 ttl=255 time=0.998 ms
64 bytes from 172.27.254.126: icmp_seq=4 ttl=255 time=1.032 ms
^C
--- 172.27.254.126 ping statistics ---
5 packets transmitted, 5 packets received, 0% packet loss
round-trip min/avg/max/stddev = 0.998/1.056/1.126/0.047 ms
Server --> MPLS --> VRF --> Customer - Destination Unreachable
> ping routing-instance BACKUP_SERVERS 172.27.254.99    
PING 172.27.254.99 (172.27.254.99): 56 data bytes
76 bytes from 124.47.128.30: Destination Net Unreachable
Vr HL TOS  Len   ID Flg  off TTL Pro  cks      Src      Dst
4  5  00 0054 940d   0 0000  40  01 3404 172.28.91.252  172.27.254.99
76 bytes from 124.47.128.30: Destination Net Unreachable
Vr HL TOS  Len   ID Flg  off TTL Pro  cks      Src      Dst
4  5  00 0054 a361   0 0000  40  01 24b0 172.28.91.252  172.27.254.99
76 bytes from 124.47.128.30: Destination Net Unreachable
Vr HL TOS  Len   ID Flg  off TTL Pro  cks      Src      Dst
4  5  00 0054 a8ae   0 0000  40  01 1f63 172.28.91.252  172.27.254.99
76 bytes from 124.47.128.30: Destination Net Unreachable
Vr HL TOS  Len   ID Flg  off TTL Pro  cks      Src      Dst
4  5  00 0054 ad11   0 0000  40  01 1b00 172.28.91.252  172.27.254.99
76 bytes from 124.47.128.30: Destination Net Unreachable
Vr HL TOS  Len   ID Flg  off TTL Pro  cks      Src      Dst
4  5  00 0054 b5ab   0 0000  40  01 1266 172.28.91.252  172.27.254.99
--- 172.27.254.99 ping statistics ---
9 packets transmitted, 0 packets received, 100% packet loss
RP/0/RSP0/CPU0:macq-syd-intel2-asr9010-01#ping vrf BACKUP-MANAGEMENT 172.27.254.99
Fri Feb 14 12:42:49.771 EST
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 172.27.254.99, timeout is 2 seconds:
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/2 ms
RP/0/RSP0/CPU0:macq-syd-intel2-asr9010-01#    sh arp vrf M2MGMT23509001                    
Fri Feb 14 12:56:57.313 EST
0/1/CPU0
Address         Age        Hardware Addr   State      Type  Interface
172.27.254.99   00:14:08   0050.5682.66c0  Dynamic    ARPA  Bundle-Ether2.12
172.27.254.124  03:08:07   0050.5682.565c  Dynamic    ARPA  Bundle-Ether2.12
172.27.254.126  -          6c9c.ed03.8eb2  Interface  ARPA  Bundle-Ether2.12
RP/0/RSP0/CPU0:macq-syd-intel2-asr9010-01#    sh arp vrf M2MGMT23509001
Fri Feb 14 12:57:25.328 EST
VRF Gateway --> MPLS --> Server - Ping OK
RP/0/RSP0/CPU0:macq-syd-intel2-asr9010-01#ping vrf M2MGMT23509001 172.28.91.19
Fri Feb 14 13:00:13.402 EST
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 172.28.91.19, timeout is 2 seconds:
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 ms
RP/0/RSP0/CPU0:macq-syd-intel2-asr9010-01#sh run router bgp 17477 vrf M2MGMT23509001
Fri Feb 14 13:02:11.425 EST
router bgp 17477
vrf M2MGMT23509001
  rd auto
  label-allocation-mode per-vrf
  address-family ipv4 unicast
   redistribute connected
RP/0/RSP0/CPU0:macq-syd-intel2-asr9010-01#sho route vrf M2MGMT23509001                                       
Fri Feb 14 13:03:46.700 EST
Codes: C - connected, S - static, R - RIP, B - BGP
       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
       E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
       i - ISIS, L1 - IS-IS level-1, L2 - IS-IS level-2
       ia - IS-IS inter area, su - IS-IS summary null, * - candidate default
       U - per-user static route, o - ODR, L - local, G  - DAGR
       A - access/subscriber, - FRR Backup path
Gateway of last resort is not set
B    10.117.24.0/23 [20/0] via 172.27.0.110 (nexthop in vrf BACKUP-MANAGEMENT), 1d01h
B    10.135.0.0/24 [20/0] via 172.27.0.110 (nexthop in vrf BACKUP-MANAGEMENT), 1d01h
B    10.135.2.0/24 [20/0] via 172.27.0.110 (nexthop in vrf BACKUP-MANAGEMENT), 1d01h
C    172.27.254.96/27 is directly connected, 2d02h, Bundle-Ether2.12
L    172.27.254.126/32 is directly connected, 2d02h, Bundle-Ether2.12
B    172.28.1.240/28 [200/0] via 125.7.35.120 (nexthop in vrf default), 6d22h
B    172.28.91.0/24 [200/0] via 125.7.35.120 (nexthop in vrf default), 6d22h
B    172.28.92.0/24 is directly connected, 1d01h, Bundle-Ether4 (nexthop in vrf BACKUP-SERVER)

Similar Messages

  • [svn:fx-trunk] 10459: Change to ensure ScriptNodes are no longer part of the node tree after interface compilation stage in order to avoid the extra code that was necessary to avoid tripping over them during type checking , etc.

    Revision: 10459
    Author:   [email protected]
    Date:     2009-09-21 08:42:44 -0700 (Mon, 21 Sep 2009)
    Log Message:
    Change to ensure ScriptNodes are no longer part of the node tree after interface compilation stage in order to avoid the extra code that was necessary to avoid tripping over them during type checking, etc.
    Improving revision 10199 a bit, to allow for single line comments.
    QE notes: None
    Doc notes: None
    Bugs: SDK-22027
    Reviewer: Paul
    Tests run: Checking, Compiler cyclones
    Is noteworthy for integration: No
    Ticket Links:
        http://bugs.adobe.com/jira/browse/SDK-22027
    Modified Paths:
        flex/sdk/trunk/modules/compiler/src/java/flex2/compiler/as3/AbstractSyntaxTreeUtil.java
        flex/sdk/trunk/modules/compiler/src/java/flex2/compiler/mxml/InterfaceCompiler.java
        flex/sdk/trunk/modules/compiler/src/java/flex2/compiler/mxml/builder/AbstractBuilder.java
        flex/sdk/trunk/modules/compiler/src/java/flex2/compiler/mxml/builder/DocumentBuilder.java

    In general theory, one now has the Edit button for their posts, until someone/anyone Replies to it. I've had Edit available for weeks, as opposed to the old forum's ~ 30 mins.
    That, however, is in theory. I've posted, and immediately seen something that needed editing, only to find NO Replies, yet the Edit button is no longer available, only seconds later. Still, in that same thread, I'd have the Edit button from older posts, to which there had also been no Replies even after several days/weeks. Found one that had to be over a month old, and Edit was still there.
    Do not know the why/how of this behavior. At first, I thought that maybe there WAS a Reply, that "ate" my Edit button, but had not Refreshed on my screen. Refresh still showed no Replies, just no Edit either. In those cases, I just Reply and mention the [Edit].
    Also, it seems that the buttons get very scrambled at times, and Refresh does not always clear that up. I end up clicking where I "think" the right button should be and hope for the best. Seems that when the buttons do bunch up they can appear at random around the page, often three atop one another, and maybe one way the heck out in left-field.
    While I'm on a role, it would be nice to be able to switch between Flattened and Threaded Views on the fly. Each has a use, and having to go to Options and then come back down to the thread is a very slow process. Jive is probably incapable of this, but I can dream.
    Hunt

  • Wrt1900ac (I changed the local ip of the router after a power outage)

    I changed the local ip of the router after a power outage,which brings me a lot of trouble because I have everything set up based on a class C network (192.168.1.x) and I changed it to a ip Type A (10.xxx), someone happens the same there any solution ?

    Hi juanmanuelvazquez. Have you tried to do a hard reset to the unit and reinstall it from scratch?  I suggest that you do so as power interruption normally brings the router back to default settings thereby messing up the network. To do the proper reset, please press down the reset button at the back of the router for 30 seconds while the device is powered on. Release the button and unplug the device. Reinstall everything from scratch.
    Hope that helps.

  • No messages by perfoming a Function After Data Change - Web Interface Build

    Hey Xperts,
    I have a problem to see messages, when I perform a Function via WEB - Function After Data Change.
    You can select by costomizing a Subcomponent "Layout" that a Function can be performent by the feature "Function After Data Change".
    But when I run the function there is no message in the message tray.
    When I run the function via Button, there will come up a messages.
    Is this a buk or a feature.
    How can I see message by performing a Function After Data Change ?
    Thanks for help.
    Thomas

    Hi Thomas,
    the system works as designed. It would be a bit anoying if the success messages are always displayed. Therefore only errors are shown.
    If you really need it, here's the modification:
    Include LUPWB_COMPONENTD18
    *   PROCESS FUNCTION (after data set)
        if m_state-request-function = cb_true.
          l_function ?= if_upwb_c_layout2~get_function( ).
          if l_function is not initial.
            l_function->_execute(
    *          i_show_success_msg = cb_false ).   "<<<DELETE
               i_show_success_msg = cb_true ).   "<<<INSERT
          endif.
          m_state-request-function = cb_false.
        endif.
    Regards
    Marc
    SAP NetWeaver RIG

  • %OSPF-4-FLOOD_WAR messages after config change

    I recently changed some configs on two L3 switches running OSPF.  After this change I'm now getting the below log message about ever 2 minutes or so on one of the switches (172.22.0.53):
    %OSPF-4-FLOOD_WAR: Process 1 re-originates LSA ID 172.18.24.3 type-2 adv-rtr 172.22.0.53 in area 0
    The two switches are using loopbacks 172.22.0.53 and 172.22.0.89, and are connected via a radio link.  Previously both switches were using Layer 3 vlan interfaces with their OSPF configs applied to those vlan interfaces, then the physical interfaces were added in this VLAN as a L2 interface.  The radio AP's were also within this vlan and not participating in OSPF.  Under this setup I was not getting these Flood War messages, but was having a spanning-tree issue which is why I removed the L3 vlan interfaces.
    I changed the physical ports to routed ports and copied the L3 vlan interfaces over and removed the L3 vlans.  This is working, but now I'm getting these OSPF Flood war messages.  I didn't change any router ID's, and the IP's set on the L3 vlans were moved to the L3 routed ports so I'm not sure where the duplicate is coming from.  I've attached the configs of both switches.
    Any ideas?

    Hi
    from url:-
    http://www.cisco.com/c/en/us/support/docs/ip/open-shortest-path-first-ospf/9237-9.html
    Q. What does the error message %OSPF-4-FLOOD_WAR: Process process-id re-originates LSA ID ip address type-2 adv-rtr ip address in area area id means?
    A. The error message is due to the some router that is flushing the network LSA because the network LSA received by the router whose LSA ID conflicts with the IP address of one of the router's interfaces and flushes the LSA out of the network. For OSPF to function correctly the IP addresses of transit networks must be unique. If it is not unique the conflicting routers reports this error message. In the error message the router with the OSPF router ID reported as adv-rtr reports this message.
    Also on your 53 config
    You have a paasive int on vlan 153 but that SVI does not exist , 133 does though
    Regards
    Alex

  • How do I set up security on my linksys router after the i...

    How do I set up security on my linksys router after the install of a net gear wireless pc adapter?

    Setting up your wireless connection in your router.
    1.Open Internet Explorer and type 192.168.1.1 into the address bar.
    2.You will now get a sign-in box, User Name = (Leave Blank)
                                                           Password = admin (all lower case letters)
    3.Once the set-up page opens, click on the Wireless Tab as youwill need to change the settings. A) Wireless Network Mode = Mixed
                  B) Wireless Network Name (SSID) = Choose any name and do not use Linksys.
                  C) Wireless Channel = 1, 6 or 11 is best, so see which work best for you.
                  D) Wireless SSID Broadcast = Enabled.
    4. Now go to the bottom of the page and click on save settings.
    5. Click on the Wireless Security Sub tab.
                  A) Security Mode: WPA
                  B) WPA Algorithms: TKIP + AES
                  C) WPA Shared Key:  Type 24 letters, and numbers using lower and upper case letters
                  D) Group Key Renewal: 3600
    6. Once again go to the bottom of the page and click on Save Settings.
    7. Now you can close out of this page.
    8. You will now need to enter the security info into your computer. I will now give you 2 links, depending which operating system you have, Vista or XP you will follow the one you have.
    Vista = http://www.home-network-help.com/wireless-adapter-configuration-in-vista.html
    XP = http://www.home-network-help.com/wireless-adapter.html
    Now try to make a wireless connection.
    Good Luck,
    Ttech

  • No automatic connection to a wireless router after startup!

    After adding a new wireless router to my home network an iMac G5 does not automatically connect to the wireless network after startup.
    And so the story began: I'm running a wireless network for years without problems at my home. The wireless router is a Orinoco 102.11b with 128-Bit WEP encryption and I have 4 different Mac connected to it.
    Because I wanted to use the higher 54 MBit/s speed and a more secure encryption for my network I've installed a LINKSYS wireless router and configured it for 102.11g and WPA2.
    Everything worked fine except the automatic connection after restart on my iMac G5 running Mac OS 10.4.10. I can connect to the new wireless router but I have to do it manually after each restart. The password is therefore stored in the login keychain. The connection can be established automatically after sleep but not after startup...
    So I switchted the connection back to the old router and got unfortunately the same behaviour. The iMac does not connect any more automatically to the router after startup. I removed the new router from the network, deleted all wireless passwords from the system and login keychains, created new keychains, switched back and forth the preferred vs. automatic network selection, created new locations, changed the root password and so on...
    It seems that the new password entry in the system keychain causes an error in the password encryption of the system keychain which prevents the automatic connection to the network after startup. Replacing the keychains from my backup does not work either after I've once created a the system keychain.
    Is there any log file, which may proof my assumption or can give me some more information of the erroneous login process to the wireless network during startup.

    One thing that can work, try this, *please ignore the exact symptoms and connection and Hardware types*, it's worked for many others than the stated...
    http://docs.info.apple.com/article.html?artnum=304482

  • WRT54G, Firmware Version: 8.00.2, Stops routing after a day, Requires Power Cycle to Work Properly

    WRT54G, Firmware Version: 8.00.2, Stops routing after a day, requires a quick 10-15 second power cyc... work properly for a day or so before powering down again….
    I was using for years the BEFW11S4 Model without any issues before it finally failed. Due to loyalty, I went out over a month ago to purchase the current model. The problems did not pop-up until month of December… The issue had me thinking at first was the internet connection…
    Any advice on dealing with this issue… Is it a Software and/or Hardware? It appears to be a software related condition…
    For those other WRT54G users that appear to be having similar issues, regardless of the firmware, it would appear we all seem to be facing the same condition of resolving the issue after a power cycle…
    Is there anyone out there that has already resolved this issue (e.g. Configuration changes)? Does anyone have input that Linksys is actively working on this issue?
    Although I am sure we will find a solution, having to cycle the power is a bit disappointing since my older model had no such flaws with my current internet connection…
    Thanks for the support out there….

    If you have an Intel wireless card you can try this.  I came across this link on the forum a days ago and it seems to help.  The problem is that my problem was much more intermittent than some people are experiencing.  It mainly seemed to appear when undocked the computer or if there was a power outage during the day.  I would be interested to see if it works for you or if I'm just chasing my tail.  I've seen other suggestions for changing the thresholds in the router which may be related.
    http://www.intel.com/support/wireless/wlan/sb/cs-006205.htm

  • Revising Services based on interface changes

    I expect this to be an easy question.  I've struggled with updating a service after making function module interface changes e.g. adding removing fields, structures or changing types. 
    What is the process to update a webservice after supporting function module changes?
    Thanks in advance.
    /Greg

    i tried it before i gave you that advice and just now again and it worked for me (although the poup came when i clicked the check button rather than already at save).
    what's definitely supposed to work is to just delete the service definition and create a new one.
    and yes it was in SE80.
    anton
    Edited by: Anton Wenzelhuemer on Oct 21, 2008 4:56 PM

  • Restricting Change of Routing without a Change Number

    Hi Techies,
    In BOM we can restrict the change of a BOM which is already changed by a change number. Is there a same way using which we can restrict the change of a routing which we have changed once with a change number. The client does not want any engineers to change it without a change number.
    Can you please advice on this.?
    Thanking you in advance.
    Regards,
    Kris.S

    Hi Techies,
    Thanks for your reply.
    I checked the setting in OP5A. I was able to make the field for change number mandatory. But i want to make it mandatory only after a Routing is changed with a change number.
    Until then i don need to make it mandatory for history requirements.
    Is this possible just like assing the field C_STUE_NOH to the Routing transaction and making it No (") and mandatory for changing routing with the change number?
    Is this possible?
    Thanking you in advance.
    Regards,
    Kris.S

  • My ipod works in itunes but does not appear in "my computer" after I changed the properties

    My ipod works in itunes but does not appear in "my computer" after I changed the properties.
    First off, I'm using Windows XP (and Mac SnowLeopard) Here's how it started. For some reason my ipod started showing up as a camera when I plugged it in. It works fine in itunes, though. But when I tried to access it from "my computer" it only
    showed me the one and only picture I had on my ipod. I deleted that picture hoping it would no longer show up as a camera. When it still did I right-clicked on it in "my computer" and selected "properties". Under "autoplay" I
    chose for it to 'not show up' or 'take no action' or some such deal when I plugged it in. I thought that would stop it from popping up the window that asks whether i want to 'open camera wizard' or 'open camera scanning' or 'open folder to view files' or 'take
    no action' , etc. But now it won't show up in "my computer" at all. I also have a Mac with SnowLeopard. When I plugged my ipod into it my ipod doesn't show up in "finder" either! So basically my problem is not a mechanical one with hardware
    or software; yht ipod still works fine in itunes. I just need to undo the change I made. I've searched all around my preferences, utilities, options, etc. It shows up on my "Device Manager" but not on "Disk Management".
    Any help would be very much appreciated. Thanks.

    Hi,
    To show up in Windows Explorer, you can try placing the iPod into
    disk mode.
    Moreover, i recommend you to
    restore ipod to factory settings.
    If this issue still persists, locate to device manager, uninstall and reinstall USB Mass Storage Device driver.
    Here is an article you can refer to below:
    http://support.apple.com/kb/TS1369
    To get more help, you can also redirect to apple support forum:
    http://www.apple.com/support/ipod/
    Thanks!
    Andy Altmann
    TechNet Community Support

  • Admin permanent status gone after password change

    Hi everyone.
    a couple of days ago i decided to change my password as good safety measure. changed as usual, only getting a message about keychain and a possible need to do the change in it after unlocking. seemed pretty standard to me, don't know if it is. (6 month mac user...)
    however, for some strange reason, afterwards the change, even if i am still an admin in the user accounts i have to identify myself with pass every time i need to do some change in admin areas, as changing the apps in the apps folder.
    i seem to be working as a standard guest , needing to elevate my status every time i need to something standard as changing my apps or renaming them.
    i've tried correcti the permissions in the disk utility and also tried to repair my keychain, without great sucess.
    anyone knows how can i get my permanent admin status again? it's a pain to need to type a password every time i want to drag and drop an app!
    Filevault is active on my home folder.
    thanks for your help
    filipe

    Macbook-de-Filipe:Applications filipe$ ls -aldeO /Applications/scilab-5.1.1.app
    [email protected] 3 filipe wheel - 102 17 Abr 20:42 /Applications/scilab-5.1.1.app
    for example this one. an app in Apps folder i wanted to update
    i didn't changed app folder permissions before. i believe all this weird behaviour appeared after i changed my password.is there a system log i can see?
    i was cheking the app folder permissions and is :
    system : read and write
    wheel : read
    everyone: read
    i haven't changed them before but i have found that if i had a admin group with read and write permissions i can have back my standard usage. however i don't know the implications of this and don't like treating the symptom, prefer instead to treat the cause
    thanks for your help V.K.

  • How do you update apps that where purchased using different iTunes accounts?  I get a cannot connect to iTunes message and it won't accept the password even after you change it.

    Both my iPad and iPhone have the same problem.  I have purchased apps with three different accounts. I understand I will need to use the original acct to do the update but every time it asks for the password I put it in and get a message that I cannot connect to iTunes store. I have even had the password reset and it still will not connect on the upgrade.  But I can sign in with that account and purchase new apps i am loading a free one now just to make sure. So what is that about?  Please do not tell me I have to also use the original password!  We have reset them so many times that there is no way to remember the original one used at time of purchase a year and 1/2 ago.  Please help. I have also upgraded to the iCloud thinking this would solve the problem but it still exists.

    I use only one Apple ID and only one ID. I did have to change the password at one point but I had no issues at all with updating apps after I changed the password.
    If you can download new apps with the ID that you changed the password for, I would think that you will be able to update apps associated with that ID as well.
    Did you try restarting the iPad after signing out of the one account and then sign in to the other account/accounts?

  • Crystal Report (RDC) doesn't print correctly, after Printer change ?

    There are problems with the page format and the color settings for the new printer !
    It should be resolved with ADAPT01104291 FixPack3.8
    Description: Crystal reports may not print properly after users change printers by using the SelectPrinter command from the Report Designer Component (RDC). The cause of the problem is that the incorrect DEVMODE structure size is allocated to the print job.
    We are using CRXI_R2_SP5_Upgrade: ProductID=11.5.11.1470.2.26.Patch
    but we still have the problems !

    Hello Don, thank you for your extensive answer. The PCL printer of HP is not the trouble maker. The problem is obviously replicable with any other Printer Driver (Espon/Sharp/Kycocera a. s. o.)  I only installed this PCL Printer Driver of course you mentioned it in your example before.
    Okay, let's talk about the Devcap-Program and there Information about the paper source of a printer. Even in Visual Basic it's possible to get those Information by Win-API-Call's. Here they are:
    PrinterID: , AusgabeName: , TreiberName: , Port: LPT1:, TrackDefault: , PaperSize:
    Papier-Schächte:
    Automatisch auswählen, Nr: 15
    Automatische Druckeraus, Nr: 262
    Schacht 1, Nr: 261
    Schacht 2, Nr: 260
    Schacht 3, Nr: 259
    Schacht 4 (2000-Blatt), Nr: 258
    Manueller Einzug (Schac, Nr: 257
    Papier-Formate:
    Letter, Nr: 1
    Legal, Nr: 5
    Statement, Nr: 6
    Executive, Nr: 7
    A3, Nr: 8
    A4, Nr: 9
    A5, Nr: 11
    B4 (JIS), Nr: 12
    B5 (JIS), Nr: 13
    11x17, Nr: 17
    Umschlag 10, Nr: 20
    Umschlag DL, Nr: 27
    Umschlag C5, Nr: 28
    Umschlag B5, Nr: 34
    Umschlag Monarch, Nr: 37
    Jap. Doppelpostkarte gedreht, Nr: 82
    12x18, Nr: 131
    9x12, Nr: 132
    C4, Nr: 133
    Maximum 11,7 x 17,7, Nr: 134
    and even set those Information for the RDC-Sturcture, so there is a solution for the setting of the paper size.
    But there is not solution for the setting of the color nor the further page settings (Printing onesided or bothsided a.s.o.)
    I can change the default windows printer settings but that has no effect on the RDC-Print !  So I think, there must be a solution by the Crystal-Report-Design-printing-DLL (craxdrt.dll) !
    Greetings V. Hölscher

  • How do I retain my apps after I change my apple ID? Right now I'm unable to update any of the apps with the old apple ID. I get an error message about an invalid id or password. If I delete my apps and start over, I may lose the apps that I purchased...

    How do I retain my apps after I change my apple ID? Right now I'm unable to update any of the apps with the old apple ID. I get an error message about an invalid id or Password. If I delete my appos and start over, I may lose the apps that I purchased (like the ones for $5 +....

    Apps are always tied to the ID that was used to purchase them originally. Did you try entering your old password and see if that works?
    If you need to sign out of your old account go to Settings>Store>Tap on your ID and sign out. Sign in with the new one.
    you can also access your ID in the featured tab of the App Store. Swipe to the bottom of the screen and you will find it there as well.

Maybe you are looking for