No SATA drive after booting into Windows (BootCamp 5.0)

One of my DVD burners has failed in one of my 2008 Apple Mac Pro's. I pulled the drive out (it was PATA/IDE) and replaced with a new LG WH14NS40 Blu-Ray Burner. I had to pull the fan out (temporarily) and run a new 24" SATA cable (with right-angle connector) from one of the two extra SATA ports (on the motherboard) to the new actual SATA drive, and also install a MOLEX to SATA power connector.
I managed to get the drive installed (and working). I now at least have a Blu-Ray burner in my 2008 Apple Mac Pro (with OS X 10.8.3 Mountain Lion).
The problem seems to be with when I boot directly into Windows 8. When I boot into Windows 8, the two ports on the motherboard are disabled and the latest BootCamp 5.0 drivers don't seem to support the two SATA ports on the motherboard (they seem to be disabled). So when I boot directly into Windows, my LG WH14NS40 Blu-Ray drive disappears.
I really wish Apple would have just "done things right" from the very beginning and took the time to write decent BootCamp 5.0 drivers that supported the two SATA ports on the motherboard, so that users who need to replace their old/dying/aging PATA drives could easily replace them with SATA drives and use the two SATA ports on the motherboard.
Also it would have been nice if Apple would have taken the time to write good BootCamp 5 drivers (for Windows 8) that support booting from the two SATA ports on the 2008 Apple Mac Pro motherboard.
I've heard of many people that have tried installing RAID Controller Cards (from OWC) in their 2008 Apple Mac Pro to upgrade their four hard drive caddys from SATA II (3Gbps) to SATA III (6Gbps) but unfortunately the RAID Controller Cards don't seem to be bootable and the only option is to install a fifth (bootable) hard drive into the Apple Mac Pro and this is normally done by installing a bootable SSD drive into one of the DVD-drive bays. Unfortunately if you use a SATA SSD drive (which most SSD's are SATA) and then use one of the two SATA ports on the motherboard to connect it, then you go back to having the problem of not having a boot drive when you boot directly into Windows 8 (since there are no BootCamp 5 drivers for the 2008 Apple Mac Pro that support the two SATA ports on the 2008 Apple Mac Pro motherboard).
This seems to be a never-ending problem, and we have twelve 2008 Apple Mac Pro's (along with an office full of 2008/2009/2010/2013 Apple Mac Pro's) and we're getting extremely frustrated with Apple's lack of support in BootCamp 5.0 drivers for the 2008 Apple Mac Pro (and the two SATA ports on the mainboard).
Please fix this problem, and please update the BootCamp 5.0/5.1 drivers (for 2008 Apple Mac Pro users) and please support the two SATA ports on the Apple Mac Pro mainboard, and please make those two SATA ports on the motherboard bootable and usable in both Microsoft Windows 8 and in OS X 10.8.3 Mountain Lion. Please update the BootCamp 5.0 drivers to support the two onboard SATA ports in Windows 8 (so that my Blu-Ray burner is viewable/usable in Windows 8).

Just as a follow-up, yes it does seem to be possible to get both SATA ports on a 2008 Apple Mac Pro working (in Windows 8).
You need to enable AHCI in Windows 8.
First boot into Windows 8 and then go into the windows registry (regedit) and enable AHCI in your registry.
You can do this by going to the following registry key:
Computer\HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\storahci
Set the "Start" Value data to "0" (to enable AHCI in Windows).
After AHCI is enabled in Windows, then reboot your computer and now the SATA drive (connected to the ODD port) should appear in Windows (under devices).
Now the next step is to update your AHCI drivers (in Windows) to the latest Intel drivers, so that your SATA device will actually work (and work properly).
The latest Intel RST drivers can be found here: https://downloadcenter.intel.com/Detail_Desc.aspx?agr=Y&ProdId=2101&DwnldID=2306 0&ProductFamily=Software+Products&ProductLine=Chipset+Software&ProductProduct=In tel%C2%AE+Rapid+Storage+Technology+(Intel%C2%AE+RST)&lang=eng
Download the 64-bit drivers (if you are running 64-bit Windows).
After you install the latest drivers, and perform a reboot, your SATA drive should now work under windows.
You can find a long detailed thread about enabling AHCI (in Windows 7) here: http://forums.macrumors.com/showthread.php?t=760482
The thread listed above is a bit old/dated (2009?) but it does give detailed step-by-step instructions for those that want to enable AHCI (and get those two onboard SATA ports working in Windows 8 or Windows 7).
I managed to get everything working in Windows 8, and I was able to enable AHCI in Windows 8, installed the latest AHCI drivers and I'm now able to use my SATA Blu-Ray burner in my 2008 Apple Mac Pro.
Hope this helps!
-> Mark

Similar Messages

How do I access the music from my Mac drive while booted into Windows?

How do I access the music from my Mac drive while booted into Windows via Bootcamp? I tried using MacDrive but it's not supported for Vista 64-bit edition. Is there another program out there that I can use? I just want to be able to access my music that's on Leopard while in Vista. Any advice will be much appreciated. Thanks in advance.

Your best bet is to move the music on the Windows side since Leopard will be able to read and play the music from the mounted Windows drive (Leopard will not be able write anything to the Windows NTFS partition).
In your case it won't work the other way around.
Axel F.

Have to restore OS X.9.1 after booting into Windows 7 on Bootcamp

I am having an odd problem--whenever I boot into Windows 7 on bootcamp, when I then boot into Mac OS X.9.1, I have to restore the disk from Time Machine. This has never happened before, but now has happened twice in a row. It takes hours for the Restore function to restore everything. Anyone have any idea as to why this is happening. My MacPro dates to 2010. Thanks.

Windows is a guest on your Mac. If you use Windows tools to change the partition Map, or the size of any partition, all Mac OS X partition information is trashed, and you will need to restore it before proceeding.
Otherwise, you should be able to hold down Alt/Option key at Startup, and select your Mac OS X Volume to boot from (after several minutes of discovering what Volumes are present).

Imac auto boots into windows bootcamp

I just installed windows 8 using bootcamp. Installed it without issue (magic mouse wouldn't work though), now i can't boot into mac. it won't even send me to the boot options. I turn on holding option, like apple says I should. But i get a blinking underscore for a second, then boots into windows 8. My magic mouse still doesn't have drivers to work. I'm not sure what to do. I have also tried holding down cmd + r, but nothing happens as well. my keyboard does work, just not my magic mouse.
Thanks for the help!

Yes, when you were in Boot Camp getting ready to install Windows you missed step 1
Downloading the Windows Support Software, go back and do it now.

NF750-G55 - Does not detect usb mouse (have to plugin after boot into Windows)

Topic says it all...
Mouse is Microsoft Habu, has been working in my old system just fine (ASUS M2N32-SLI DELUXE). The only usb items plugged in are the mouse and my Logitech G11 Keyboard.
I just upgraded my old rig to what you see in my signature, my mouse will not get detected unless I replug it in after windows has started.
During boot after initializing usb controller it says Found: 1 Keyboard and 1 Hub
I have tried the following but with no successful results:
PS2 Keyboard with mouse (mouse behaves the save)
Mouse w/usb->ps2 adapter (mouse lights up but doesn't do anything in windows)
Mouse plugged into every different port on the MOBO, D-Bracket, front panel usb or even into keyboard
Different mouse (boot says Found: 1 Keyboard, 1 Mouse, 1 Hub) and this mouse works all the time
USB Legacy On/Off inside bios
I also have a USB powered hard drive (http://www.simpletech.com/products/storage/simpledrive-mini/red-wine-250gb.php) that when plugged into the motherboard was making a beeping sound but I can't find any information on what that means (if anything)
Any ideas?

Quote
I just upgraded my old rig to what you see in my signature, my mouse will not get detected unless I replug it in after windows has started.
I had a similar problem with a couple of different boards, but with a Razer Copperhead mouse. I ended up just buying a new mouse (PS/2 type).

System locks about 3min after booting into windows

AMD TB 1.4ghz
512mb Elixer DDR ram
K7N Delta 2 board
430W Power supply (just bought)
WD 80gb HD
Boots up fine then fails shortly after. Just freezes up. I did a memory test on the RAM and no errors. Any ideas?

Quote from: tordavis on 18-September-05, 17:30:27
This same thing was happening with the Asus board and older PSU. New PSU and Board, same issue. On old board it would take a little longer but it would still happen. Especially after loading a sound app like Fruity Loops or iTunes and playing music. I'm starting to think that this old AMD TB1.4ghz cpu just doesn't like the newer boards. I'm thinking maybe I should update the bios?! The latest version is B.5 but my version is so old that it doesn't match current version numbers. Mine is an 11.4.
Discuss?
[EDIT] Noticed something else. If I let the system run for a LONG time after it's frozen and then reboot, I can't even get into bios when I hit delete. Just locks at that point. So turning it off for about 10 mins and rebooting it lets me get into bios. Those are the symptoms of an overheating problem. It's clocking my cpu at the correct 1400mhz at 133fsb. I have it set to auto. Why would it be overheating? Never had this problem with the old asus board. .18 micron tech can't handle the power this board is putting out maybe? I have a nice heatsink and fan on the cpu....this is perplexing. OH and what is that little orange plastic thing underneath where the cpu goes? It sticks straight up. Is it like a cpu thermometer?
Yes, the orange plasitc strip under the CPU is the thermal probe.
I found the 11.4 (B4) BIOS to be the most unstable of all I tested for my components. The B30 (11.3) BIOS tends to be the most stable however the B.50 (11.5) BIOS works best for me in performance.
Take labtech1's advice and try enabling the setting "PRIVATE" in dynamic overclocking because it has been found to stabilize BIOS 11.4 and 11.5

Can't boot into Windows (Bootcamp) since EFI/10.8.2 update

The boot menu no longer comes up during restart ever since I updated the EFI for my MacBook Pro with Retina display and from 10.8.1 to 10.8.2.
When I try to reboot from the preferences menu, I get this message:
http://i47.tinypic.com/rvkho4.png
As far as I can tell, the disk and the two partitions are in order:
http://i49.tinypic.com/vxi0lx.png
http://i50.tinypic.com/2gy9lc0.png
http://i50.tinypic.com/fxsdht.png
When I try to use the Alt/Option key during boot-up method, it fails to bring up the boot menu and just brings up my login window.

The boot menu no longer comes up during restart ever since I updated the EFI for my MacBook Pro with Retina display and from 10.8.1 to 10.8.2.
When I try to reboot from the preferences menu, I get this message:
http://i47.tinypic.com/rvkho4.png
As far as I can tell, the disk and the two partitions are in order:
http://i49.tinypic.com/vxi0lx.png
http://i50.tinypic.com/2gy9lc0.png
http://i50.tinypic.com/fxsdht.png
When I try to use the Alt/Option key during boot-up method, it fails to bring up the boot menu and just brings up my login window.

Cannot boot into Windows XP, should I replace hard drive?

THE PROBLEM: I have not been able to boot into or use Windows XP (SP2) for almost 3 years. I have been using Linux instead for 3 years and am using it now. The Windows Recovery process only half works, it works up until you have to boot up the computer from the hard drive. Then it no longer works. The computer will load the files from the TOSHIBA Recovery and Applications/Drivers DVD that came new with the computer onto the hard drive. But when you get to the point of booting off the hard drive, with newly added Windows & Toshiba files, nothing happens. It does not boot up into Windows XP. In fact I can see the newly added Windows & Toshiba fileson the hard drive when I boot into Linux (Live) off the hard drive.
THE HARD DRIVE (Specs below): I ran a SMART Data check using a Linux (Ubuntu) Disk utility on the hard drive and it passed everything except for Reallocated Sector Count. There are 20 bad sectors. I called the Toshiba 800 # on the DVD and they told me that the problem may be the hard drive. A new TOSHIBA Recovery and Applications/Drivers DVD costs $40. Toshiba also said there is no Windows XP Recovery Console on the DVD.
CAUSE OF THE PROBLEM: I think, and TOSHIBA agreed it is either the hard drive or corrupteD files on the TOSHIBA Recovery and Applications/Drivers DVD
POSSIBLE SOLUTIONS: I have found a couple of sites that seem to have instructions for making a Windows XP Recovery Console CD. And I have thought I might try to run some Windows XP Recovery Console commands from such a CD, such as fixboot, fixmbr, etc. The try to see if I can boot into Windows XP from the hard drive. If I can, then that might suggest he problem is corrupted files on the TOSHIBA Recovery and Applications/Drivers DVD. If I still cannot boot into Windows, then maybe I should replace the hard drive. This should be very easy to do.
QUESTION(S): Does anybody have any comments or suggestions? Does my approach sound good? Do you have any other suggestions?
I have a TOSHIBA Satellite L25 S1216 that I bought new in early 2006. It has a 40 GB (5400 RPM) Enhanced IDE (ATA-6) 9.5 mm height hard disk drive in it. User removable, i.e., it is easy to replace.
Thank you,
Bob
Solved!
Go to Solution.

My plan is to try to use the TOSHIBA Recovery and Applications/Drivers DVD to load the WIndows XP files onto the hard drive, then use the Windows XP Recovery console CD I downloaded from here
http://www.proposedsolution.com/downloads/download-windows-recovery-console/
by using commmands such as fxmbr, fixboot, etc to see if I can get the computer to boot up into Windows XP.
Good plan, Bob!
Description of the Windows XP Recovery Console for advanced users
A backup plan would be to obtain a Windows XP installation CD from eBay or wherever. They are super cheap now. Then you could install Windows clean and add the drivers and utilities from the website here. Or you could use it to repair-install Windows.
How to Perform a Windows XP Repair Install
You are entitled to activate Home Edition for free. I understand that even after Microsoft no longer supports Windows XP (in April), they will honor activation attempts.
I wouldn't mess with SSDs. And stick with IDE PATA drives. You won't need to worry about advanced-format technology since that didn't come along until the very recent SATA drives. Your BIOS should support 120GB (KB303013). Some here.
-Jerry

Can't boot into Windows 8.1 partition after apple store repair

Can't boot into Windows 8.1 partition after apple store repair
I went to the apple store about a week ago to get my screen fixed, and when I get it back I don't have an option to boot into my windows partition. The bootcamp partition is still there, but I can't boot into it. I can still see all of the files on the drive. When I try to boot into windows from the startup disc setting I get "no bootable device — insert boot disk and press any key” on a black screen. I went in for a dead pixel, and the guy at the genius bar ran something on my computer and went into disk utility application. I’m not sure what he was doing, but obviously that’s what messed up my windows partition. How can I be able to boot back into windows? Here's what disk utility looks like on my computer.

Here's the output
00000000 eb 52 90 4e 54 46 53 20 20 20 20 00 02 08 00 00 |.R.NTFS .....|
00000010 00 00 00 00 00 f8 00 00 3f 00 ff 00 00 b0 0e 2b |........?......+|
00000020 00 00 00 00 80 00 80 00 ff bf 2e 0f 00 00 00 00 |................|
00000030 00 00 0c 00 00 00 00 00 02 00 00 00 00 00 00 00 |................|
00000040 f6 00 00 00 01 00 00 00 05 92 d3 74 c4 d3 74 aa |...........t..t.|
00000050 00 00 00 00 fa 33 c0 8e d0 bc 00 7c fb 68 c0 07 |.....3.....|.h..|
00000060 1f 1e 68 66 00 cb 88 16 0e 00 66 81 3e 03 00 4e |..hf......f.>..N|
00000070 54 46 53 75 15 b4 41 bb aa 55 cd 13 72 0c 81 fb |TFSu..A..U..r...|
00000080 55 aa 75 06 f7 c1 01 00 75 03 e9 dd 00 1e 83 ec |U.u.....u.......|
00000090 18 68 1a 00 b4 48 8a 16 0e 00 8b f4 16 1f cd 13 |.h...H..........|
000000a0 9f 83 c4 18 9e 58 1f 72 e1 3b 06 0b 00 75 db a3 |.....X.r.;...u..|
000000b0 0f 00 c1 2e 0f 00 04 1e 5a 33 db b9 00 20 2b c8 |........Z3... +.|
000000c0 66 ff 06 11 00 03 16 0f 00 8e c2 ff 06 16 00 e8 |f...............|
000000d0 4b 00 2b c8 77 ef b8 00 bb cd 1a 66 23 c0 75 2d |K.+.w......f#.u-|
000000e0 66 81 fb 54 43 50 41 75 24 81 f9 02 01 72 1e 16 |f..TCPAu$....r..|
000000f0 68 07 bb 16 68 52 11 16 68 09 00 66 53 66 53 66 |h...hR..h..fSfSf|
00000100 55 16 16 16 68 b8 01 66 61 0e 07 cd 1a 33 c0 bf |U...h..fa....3..|
00000110 0a 13 b9 f6 0c fc f3 aa e9 fe 01 90 90 66 60 1e |.............f`.|
00000120 06 66 a1 11 00 66 03 06 1c 00 1e 66 68 00 00 00 |.f...f.....fh...|
00000130 00 66 50 06 53 68 01 00 68 10 00 b4 42 8a 16 0e |.fP.Sh..h...B...|
00000140 00 16 1f 8b f4 cd 13 66 59 5b 5a 66 59 66 59 1f |.......fY[ZfYfY.|
00000150 0f 82 16 00 66 ff 06 11 00 03 16 0f 00 8e c2 ff |....f...........|
00000160 0e 16 00 75 bc 07 1f 66 61 c3 a1 f6 01 e8 09 00 |...u...fa.......|
00000170 a1 fa 01 e8 03 00 f4 eb fd 8b f0 ac 3c 00 74 09 |............<.t.|
00000180 b4 0e bb 07 00 cd 10 eb f2 c3 0d 0a 41 20 64 69 |............A di|
00000190 73 6b 20 72 65 61 64 20 65 72 72 6f 72 20 6f 63 |sk read error oc|
000001a0 63 75 72 72 65 64 00 0d 0a 42 4f 4f 54 4d 47 52 |curred...BOOTMGR|
000001b0 20 69 73 20 63 6f 6d 70 72 65 73 73 65 64 00 0d | is compressed..|
000001c0 0a 50 72 65 73 73 20 43 74 72 6c 2b 41 6c 74 2b |.Press Ctrl+Alt+|
000001d0 44 65 6c 20 74 6f 20 72 65 73 74 61 72 74 0d 0a |Del to restart..|
000001e0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
000001f0 00 00 00 00 00 00 8a 01 a7 01 bf 01 00 00 55 aa |..............U.|
00000200
Here's a better screenshot.

IMac with bootcamp and parallel boots into windows 7 but won't boot intoxc lion.

IMac with bootcamp and parallel boots into windows 7 but won't boot into Mac OS lion?

Hi,
Thanks for your suggestion. Actually that was not the problem, because I had the Mcintosh drive set as my boot drive. The answer was that my Lion Os got somehow corrupted and I had to reinstalll Lion. This was all after I discussed the situation with the Apple Support people.

Can I boot into Windows if it is partitioned on a second hard drive?

I want to put my 2009 MBP hard drive into a 2012 MBP by replacing the optical drive with the 2009 hard drive in a caddy. The 2009 has Windows partitioned on it already through bootcamp.
Will I be able to boot into windows through the second drive or will I have to bootcamp the new 2012 drive with Windows?

OK Cool. I think I will try that. Thanks for the tip. I appreciate it.

Can only boot into Windows 7. Can't even boot from Snow Leopard DVD.

I have no idea what prompted this. I don't recall installing any OS updates recently, other than some Windows Live apps in Windows 7.
I have an early 2009 Mac Mini with Snow Leopard, and have Windows 7 64-bit installed in a Boot Camp partition. When I installed Windows 7, I couldn't get the Boot Camp utility to install within Windows (I guess because it's 64-bit) so to switch back and forth between OSes, I just shut down the Mac and restart it with the Option key pressed, and select Mac OS X when I want to return to Mac. This has worked for about a month and a half now (ever since I got Windows 7). Suddenly I have problems.
I first had problems booting into Windows or Mac. I got to the grey screen with the Apple logo, with that spinning "progress" thing going for a while, then it would freeze up and get stuck on the grey screen with the Apple logo. I zapped the PRAM. No help. Then, after disconnecting all external drives (I have several) and extra USB devices, I was able to boot from the DVD install disk and reinstall Snow Leopard on my internal drive. Joy, or so I thought. Then I booted into Windows 7, and after some weirdness getting it to start, it did successfully start and ran just peachy.
Then I turned off the Mac and held down the option key (as usual) to return to Mac OS. But now all that happens is that I get a grey screen for a few seconds, then the Mac boots back into Windows 7, which seems to work fine. (I'm in Windows 7 right now.) I turned on one my external drives (Snow Leopard installed, connected via Firewire 800) in hopes that the Mac would boot into that, but same thing. Ignored and back to Windows 7.
Then I thought I'd boot from the install DVD again by putting it in the drive and holding down the C key as I restart, but the same thing--a grey screen for a few seconds, and then booting right into Windows 7. I can't seem to escape Windows 7! It's a bit disturbing when it won't even recognize the install DVD.
I tried to call Apple Care since I'm within my 90 day support window, but of course they are closed. I'm figuring that I'm going to have to take this into an Apple Store, but thought I'd see if anyone has any ideas. Any advice will be appreciated. Thanks.

According to Apple, Win 7 64bit is supported with Bootcamp 3.0. If bootcamp 3.0 is available; I could not find it anywhere on Apple's website. It appears the most recent version is 2.2. The only place I could find 3.0 is not on Apples website and it's a questionable source so I won't post it here.
It may just be a matter of time before Apple makes it available. I'm not suggesting you wait, however if the install disk can't be used, I'm not too sure where u could go from there. Calling Applecare might work.
If you do a simple google search using the terms 'download bootcamp drivers windows 7' u will see what I was referring too.
Here's what I found from Apple (It doesn't specifically mention 64bit however just win7): http://support.apple.com/kb/HT3920
This is not from Apple, but specifically addresses whether they support win7 64bit: http://www.macnn.com/articles/09/08/31/boot.camp.win.7.64.support/
Here is more info about bootcamp 3.0 and win7: http://www.apple.com/support/bootcamp/

Can I use my Intel-based MacBook to boot into Windows 7 from an external HDD?

Okay, so I need to use Windows for some simple applications. Problem is, I don't have a Windows desktop anymore and while I have both Windows and Linux partitions along with Mountain Lion on my installed hard drive, I'm probably going to wipe said drive and just use the entire partition for Mountain Lion. That said, I'd like to use an extra hard drive I have lying around to boot Windows.
My questions are:
1. Does my MacBook support USB boot to Windows?
2. If my laptop does support this, can someone point me to a set of good reliable instructions to install Windows onto the external hard drive and boot into it by USB?
Thank you; have a blessed day!

You seem to have a triple boot system that was done using the 10.6 installer disk and a copy of rEFIt.
I know because I had the same thing once.
I can tell you what will happen if you decide to upgrade 10.7 or 10.8
1: The EFI and GUID is going to change, rEFIt hasn't been updated in ages since 10.7 started rolling out back in about June 2011. There will be adverse effects with rEFIt so I hear.
2: The 10.8 upgrader is going to barf at your triple boot system, it will upgrade the 10.6 partition but warn you that the 10.8 RecoveryHD partition (10.7 and 10.8 both install) that it normally installs at the very bottom of the drive will not be installed and you can't enable Filevault.
Intel Mac's can have only 4 bootable partitions on the drive, the 10.7+ installer is normally dealing with EFI, MacintoshHD, BOOTCAMP, RecoveryHD. It barfs at anything else it doesn't understand and will not install RecoveryHD partition, which on a non-Internet Recovery capable hardware is required to reinstall the currently upgraded OS X operating system version. But you can always go back to the 10.6 disks and wipe and restore that way or via 10.6 USB boot key.
http://www.maciverse.com/install-os-x-snow-leopard-from-usb-flash-drive.html
So with 10.7+ you'll have to use something like Carbon Copy Cloner for the OS X partition.
So since rEFIt is going to be hosed, so will your ability to use the EFI based program to boot into the three operating systems at boot time.
I assume you found this out and why you want to dump Windows on a external drive. However Apple's EFI doesn't recognize Linux as a boot option.
There is a rEFIt fork that will allow Linux to boot on a Mac: http://www.rodsbooks.com/ubuntu-efi/index.html
Windows as you now know can't be booted off a external drive, however if your use of it is minor, you may want to consider using a virtual machine to run it in OS X or Linux instead using the free VirtualBox.
Windows in BootCamp or Virtual Machine?
You should Carbon Copy Cloner the OS X 10.6 partition to a external GUID OS X Extended J (JHFS+) drive.
You can use WinClone 3 in OS X to clone the Windows partition to a external drive, but it's a backup only, no booting capability. Restoring it will boot on the internal drive of course.
Linux you should already know how to clone it to a external drive using dd.
I advise you use the 10.6 install disks to set up your new partition scheme, but your going to have to uninstall rEFIt and return the machine and firmware back to basic Apple factory system as possible before doing anything.
EFI doesn't get erased, it resides in NVRAM and the EFI partition, controls the at boot key commands to boot off OS X install disks, so it's important to uninstall rEFIt completely before upgrading OS X.
If the Windows version your using is XP, to install that first using BootCamp in a fresh 10.6 install and reverse clone using WinClone before upgrading to 10.7 or above. It will be grandfathered in, but can't be reinstalled later.

MSI K9A2 Platinum + Phenom 9600 + 2GB Mushkin XP8500 cannot boot into windows

Hi!
I am building my computer using the Spider platform and I ran across problems during booting into windows.
I am using MSI K9A2 platinum with Phenom 9600 and Mushkin 2Gb kit XP8500 ddr2 1066. I have no problem installing windows xp.
The problem starts when I install the utility and drivers that come on a cd from MSI, my computer requests to re-boot after installation and after
that it will not boot into windows. I can get to the windows logo and then the system reboots right away.
I checked the bios and it shows that the ram is running at 800mhz and i have tried running with just 1 stick and im getting the same problem every time.
Anyone knows how to resolve this?
thanks!

Quote from: nirianto on 22-February-08, 01:32:52
Everything is stable now...I guess installing the driver from the MSI website is the best thing to do right now
I notice that my ram is underclocked to 800mhz instead of 1066mhz...I have update the motherboard BIOS to v1.2 and i checked that the ram is running on unganged mode...I tried adjusting the spd to 5-5-4-12 with voltage of 2.2v as suggested by the mushkin ram itself
Any idea?
"I have update the motherboard BIOS to v1.2 and i checked that the ram is running on unganged mode..."
That is the correct mode.
"I notice that my ram is underclocked to 800mhz instead of 1066mhz..."
1066 is not officially certified by JEDEC, also your memory probably don't have SPD configuration for that freq.
Contact to Mushkin for more details.
"I guess installing the driver from the MSI website is the best thing to do right now"
Yep
"Everything is stable now.."
nice :smiley:

Hi, can anyone help with the problem I am having with pro book 4440s? I can't boot into windows 7.

Hi, can anyone help with the problem I am having with pro book 4440s? I can't boot into windows 7, nor can I enter the bios cause i fogot the password. the error I am getting says "windows failed to start. a recenr hardware or software change might be the cause. it then gives me options to boot from a disc but I can't do that cause I am unable to get into the bios to change it to boot from a disc.
The error message goes on :
File: \Boot\BCD
Status: oxcoooooof
info: An error occurred while attempting to read the boot configuration.
the only two options on the screen are enter=continue and ECS=exit
I just can't get pass this screen.
Please help.
Thanks

Hi,
If you don't already have one, use another PC to create a Windows 7 Rescue CD. Download the relevant ISO from the links below.
Windows 7 32bit
Windows 7 64bit
You should use an application such as ImgBurn to burn the ISO to a CD - a guide on using ImgBurn to write an ISO to a disc is Here. Once created, or if you already have this, tap away at the esc key as you start the notebook to enter the Start-up Menu. Insert the Rescue CD. Select Boot options ( usually f9 ), use the arrow keys to select the CD/DVD drive and hit enter. You may also get a prompt to 'Press any key to continue' - do this if asked.
When loaded, select Repair Your Computer and choose the Command Prompt. When this loads, enter the following commands and hit enter after each one - include spaces as shown.
Bootrec.exe
bcdedit /export C:\BCD_Backup
c:
cd boot
attrib bcd -s -h -r
ren c:\boot\bcd bcd.old
bootrec /RebuildBcd
bootrec /fixmbr
bootrec /fixboot
Remove the Rescue CD and try rebooting the notebook.
Regards,
DP-K
****Click the White thumb to say thanks****
****Please mark Accept As Solution if it solves your problem****
****I don't work for HP****
Microsoft MVP - Windows Experience

No SATA drive after booting into Windows (BootCamp 5.0)

Similar Messages

Maybe you are looking for